What is meant by the term antenna bandwidth A. Antenna length divided by the number of elements. B. The angle between the half-power radiation points C. The frequency range over which and antenna can be expected to perform well D. The angle formed between two imaginary line drawn through the ends of the elements

What is meant by the term antenna bandwidth
A. Antenna length divided by the number of elements.
B. The angle between the half-power radiation points
C. The frequency range over which and antenna can be expected to perform well
D. The angle formed between two imaginary line drawn through the ends of the elements
by

1 Answer

Answer :

C. The frequency range over which and antenna can be expected to perform well
by

Related questions

What is antenna bandwidth? A. Antenna length divided by the number of elements B. The angle between the half-power radiation points C. The angle formed between two imaginary lines drawn through D. The frequency range over which an antenna can be expected to operate satisfactorily

Description : What is antenna bandwidth? A. Antenna length divided by the number of elements B. The angle between the half-power radiation points C. The angle formed between two imaginary lines drawn through D. The frequency range over which an antenna can be expected to operate satisfactorily

Last Answer : D. The frequency range over which an antenna can be expected to operate satisfactorily

What is meant by the term radiation resistance for an antenna? A. The resistance in the trap coils to received signal B. An equivalent resistance that would dissipate the same amount of power as that radiated from an antenna C. The specific impedance of the antenna D. Losses in the antenna elements and feed line

Description : What is meant by the term radiation resistance for an antenna? A. The resistance in the trap coils to received signal B. An equivalent resistance that would dissipate the same amount of power as ... antenna C. The specific impedance of the antenna D. Losses in the antenna elements and feed line

Last Answer : B. An equivalent resistance that would dissipate the same amount of power as that radiated from an antenna

What is meant by the term antenna efficiency? A. Efficiency = effective radiated power/transmitter output x 100% B. Efficiency = radiation resistance/ transmission resistance C. Efficiency = total resistance/radiation resistance x 100% D. Efficiency = radiation resistance/total resistance x 100%

Description : What is meant by the term antenna efficiency? A. Efficiency = effective radiated power/transmitter output x 100% B. Efficiency = radiation resistance/ transmission resistance C. Efficiency = total resistance/radiation resistance x 100% D. Efficiency = radiation resistance/total resistance x 100%

Last Answer : D. Efficiency = radiation resistance/total resistance x 100%

In order to get maximum radiation to all surrounding points in the horizontal plane, the antenna used is a A. vertical loop B. vertical quarter-wavelength rod C. array which includes parasitic elements D. a horizontal Hertz dipole

Description : In order to get maximum radiation to all surrounding points in the horizontal plane, the antenna used is a A. vertical loop B. vertical quarter-wavelength rod C. array which includes parasitic elements D. a horizontal Hertz dipole

Last Answer : B. vertical quarter-wavelength rod

_____ is the angle between the half-power radiation points A. Critical angle B. Beamwidth C. Angle of elevation D. Azimuth

Description : _____ is the angle between the half-power radiation points A. Critical angle B. Beamwidth C. Angle of elevation D. Azimuth

Last Answer : B. Beamwidth

lobes between end of the love at which the relative power is one half (-3dB) its value from the peak of the lobe. A. Bandwidth B. Wavelength C. Radiation D. Beamwidth

Description : Width measured in degrees of a major lobes between end of the love at which the relative power is one half (-3dB) its value from the peak of the lobe. A. Bandwidth B. Wavelength C. Radiation D. Beamwidth

Last Answer : D. Beamwidth

______ is the measurement of a unilateral antenna properties of directivity A. Phase angle B. Antenna gain C. Beamwidth D. Bandwidth

Description : ______ is the measurement of a unilateral antenna properties of directivity A. Phase angle B. Antenna gain C. Beamwidth D. Bandwidth

Last Answer : C. Beamwidth

_______ is the horizontal pointing angle of an antenna. A. Right angle B. Angle of elevation C. Bandwidth D. Azimuth

Description : _______ is the horizontal pointing angle of an antenna. A. Right angle B. Angle of elevation C. Bandwidth D. Azimuth

Last Answer : D. Azimuth

Factors that determine the radiation resistance of an antenna A. Transmission line length and height of antenna B. The location of the antenna with respect to nearby objects C. It is a constant for all antennas since it is physical D. Sunspot activity and the time of day

Description : Factors that determine the radiation resistance of an antenna A. Transmission line length and height of antenna B. The location of the antenna with respect to nearby objects C. It is a constant for all antennas since it is physical D. Sunspot activity and the time of day

Last Answer : B. The location of the antenna with respect to nearby objects

Emission on a frequency or frequencies immediately outside the necessary bandwidth which result from the modulation process except spurious emission. A. Radiation B. Noise C. Out of the band D. Interference

Description : Emission on a frequency or frequencies immediately outside the necessary bandwidth which result from the modulation process except spurious emission. A. Radiation B. Noise C. Out of the band D. Interference

Last Answer : C. Out of the band

Where are the current nodes in a half-wave antenna? A. At the ends B. At the center C. Three-quarters of the way from the feed point toward the end D. One-half of the way from the feed point toward the end

Description : Where are the current nodes in a half-wave antenna? A. At the ends B. At the center C. Three-quarters of the way from the feed point toward the end D. One-half of the way from the feed point toward the end

Last Answer : A. At the ends

Where are the voltage nodes in a half-wave antenna? A. At the ends B. Three-quarters of the way from the feed point toward the end C. One-half of the way from the feed point toward the end D. At the feed point

Description : Where are the voltage nodes in a half-wave antenna? A. At the ends B. Three-quarters of the way from the feed point toward the end C. One-half of the way from the feed point toward the end D. At the feed point

Last Answer : D. At the feed point

At the ends of a half-wave antenna, what values of current and voltage exist compared to the remainder of the antenna? A. Minimum voltage and minimum current B. Equal voltage and current C. Minimum voltage and maximum current D. Maximum voltage and minimum current.

Description : At the ends of a half-wave antenna, what values of current and voltage exist compared to the remainder of the antenna? A. Minimum voltage and minimum current B. Equal voltage and current C. Minimum voltage and maximum current D. Maximum voltage and minimum current.

Last Answer : D. Maximum voltage and minimum current.

What is the term for the ration of the radiation resistance of an antenna to the total resistance of the system? A. Effective radiated power B. Beamwidth C. Radiation conversion loss D. Antenna efficiency

Description : What is the term for the ration of the radiation resistance of an antenna to the total resistance of the system? A. Effective radiated power B. Beamwidth C. Radiation conversion loss D. Antenna efficiency

Last Answer : D. Antenna efficiency

Stacking elements in a transmitting antenna system A. increases the field strength at the receiving antenna B. increases the directivity of the transmitter antenna C. decrease the size of the lobe in the radiation pattern D. both A and B

Description : Stacking elements in a transmitting antenna system A. increases the field strength at the receiving antenna B. increases the directivity of the transmitter antenna C. decrease the size of the lobe in the radiation pattern D. both A and B

Last Answer : D. both A and B

What happens to the bandwidth of an antenna as it is shortened through the use of loading coils? A. It is increased B. It is decreased C. No change occurs D. It becomes flat

Description : What happens to the bandwidth of an antenna as it is shortened through the use of loading coils? A. It is increased B. It is decreased C. No change occurs D. It becomes flat

Last Answer : A. It is increased

The effect of adding parasitic elements of a Hertz dipole is to A. make the antenna more omnidirectional B. reduce its resonant frequency C. increase the antenna’s power gain D. All of these

Description : The effect of adding parasitic elements of a Hertz dipole is to A. make the antenna more omnidirectional B. reduce its resonant frequency C. increase the antenna’s power gain D. All of these

Last Answer : C. increase the antenna’s power gain

A method of multiple accessing where a given RF channel bandwidth is divided inot smaller frequency band. A. CDMA B. ANIK-D C. TDMA D. FDMA

Description : A method of multiple accessing where a given RF channel bandwidth is divided inot smaller frequency band. A. CDMA B. ANIK-D C. TDMA D. FDMA

Last Answer : D. FDMA

Part of a microwave link can be approximated by free space conditions. The antenna gain are each 40 dB, the frequency is 10 GHz, and the path length is 80 km. Calculate the receive power for a transmitted power of 10 W? A. 0.871 μW B. 871 μW C. 0.871 mW D. 871 nW

Description : Part of a microwave link can be approximated by free space conditions. The antenna gain are each 40 dB, the frequency is 10 GHz, and the path length is 80 km. Calculate the receive power for a transmitted power of 10 W? A. 0.871 μW B. 871 μW C. 0.871 mW D. 871 nW

Last Answer : A. 0.871 μW

What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna compared to the output power of the transmitter C. The ratio of the signal in the backward direction D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Description : What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna ... D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Last Answer : D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

If the current ratios of the two or more elements must be held 5% and the phase angle to 3° the antenna is called a A. end fire array B. critical phased array C. broadband array D. wideband array

Description : If the current ratios of the two or more elements must be held 5% and the phase angle to 3° the antenna is called a A. end fire array B. critical phased array C. broadband array D. wideband array

Last Answer : B. critical phased array

The reflector and director of an antenna array are considered as A. Parasitic elements B. Transcendental elements C. Feed-points D. Driven elements

Description : The reflector and director of an antenna array are considered as A. Parasitic elements B. Transcendental elements C. Feed-points D. Driven elements

Last Answer : A. Parasitic elements

Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or load resistor B. noise factor expressed in decibels C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signal D. S/N of an ideal system divided by S/N at the output of the receiver or amplifier under test, both working at the same temperature over the same bandwidth and fed from the same source

Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source

Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals

What is included in the total resistance of an antenna system? A. Radiation resistance plus space impedance B. Radiation resistance plus transmission resistance C. Transmission line resistance plus radiation resistance D. Radiation resistance plus ohmic resistance

Description : What is included in the total resistance of an antenna system? A. Radiation resistance plus space impedance B. Radiation resistance plus transmission resistance C. Transmission line resistance plus radiation resistance D. Radiation resistance plus ohmic resistance

Last Answer : D. Radiation resistance plus ohmic resistance

Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1.0MHz and the temperature is 20˚C, and that the receiver is connected to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

A helical antenna is used for satellite tracking because of ______. A. Broad bandwidth B. Good front-to-back C. Maneuverability D. Circular polarization

Description : A helical antenna is used for satellite tracking because of ______. A. Broad bandwidth B. Good front-to-back C. Maneuverability D. Circular polarization

Last Answer : D. Circular polarization

Top loading is used in an antenna in order to increase its ___________. A. input capacitance B. beamwidth C. bandwidth D. effective height

Description : Top loading is used in an antenna in order to increase its ___________. A. input capacitance B. beamwidth C. bandwidth D. effective height

Last Answer : D. effective height

It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation, taken under the normal operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Description : It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation ... operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Last Answer : C. Mean power

Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power

Description : Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power

Last Answer : A. Carrier power

Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power

Description : Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power

Last Answer : C. Carrier power

In the case if Marconi antenna, the actual length if the radiating element is A. one-half wavelength B. one-quarter wavelength C. one wavelength D. one-eight wavelength

Description : In the case if Marconi antenna, the actual length if the radiating element is A. one-half wavelength B. one-quarter wavelength C. one wavelength D. one-eight wavelength

Last Answer : B. one-quarter wavelength

An antenna “efficiency” is computed by using one of the following equations. A. Efficiency = (radiation resistance / transmission resistance) B. Efficiency = (total resistance / radiation resistance) x 100% C. Efficiency = (effective radiated power / transmitter output) x 100% D. Efficiency = (radiation resistance / total resistance) x 100%

Description : An antenna efficiency is computed by using one of the following equations. A. Efficiency = (radiation resistance / transmission resistance) B. Efficiency = (total resistance / radiation resistance) x ... / transmitter output) x 100% D. Efficiency = (radiation resistance / total resistance) x 100%

Last Answer : D. Efficiency = (radiation resistance / total resistance) x 100%

Increasing the resonant frequency of an end-fed Marconi antenna can be done by A. adding a capacitor in series and reducing the physical length B. adding an inductor in series C. adding an inductor in series D. All of these

Description : Increasing the resonant frequency of an end-fed Marconi antenna can be done by A. adding a capacitor in series and reducing the physical length B. adding an inductor in series C. adding an inductor in series D. All of these

Last Answer : A. adding a capacitor in series and reducing the physical length

What is the effect of adding a capacitor in series with an antenna? A. The antenna’s resonant frequency will increase B. The antenna’s resonant frequency will decrease C. The antenna will be physically 5% longer than its electrical length D. A capacitor is never added in series with an antenna

Description : What is the effect of adding a capacitor in series with an antenna? A. The antenna’s resonant frequency will increase B. The antenna’s resonant frequency will decrease C. The antenna will be physically 5% longer than its electrical length D. A capacitor is never added in series with an antenna

Last Answer : A. The antenna’s resonant frequency will increase

If the length of an antenna is changed from 2.5 meters to 2.8 meters, its resonant frequency will A. increase B. depend on the velocity factor so the resonant frequency can either be increased or decreased C. will be unchanged D. decrease

Description : If the length of an antenna is changed from 2.5 meters to 2.8 meters, its resonant frequency will A. increase B. depend on the velocity factor so the resonant frequency can either be increased or decreased C. will be unchanged D. decrease

Last Answer : D. decrease

If the length of a Hertz dipole is decreased A. its resonant frequency will be lowered its distributed inductance will be increased B. its distributed inductance will be decreased C. its resonant frequency will be increased D. its distributed capacitance between the antenna and ground will be increased.

Description : If the length of a Hertz dipole is decreased A. its resonant frequency will be lowered its distributed inductance will be increased B. its distributed inductance will be decreased C. its ... frequency will be increased D. its distributed capacitance between the antenna and ground will be increased.

Last Answer : C. its resonant frequency will be increased

The frequency of operation of a dipole antenna cut to a length of 3.4 m. A. 88 MHz B. 44 MHz C. 22 MHz D. 11 MHz

Description : The frequency of operation of a dipole antenna cut to a length of 3.4 m. A. 88 MHz B. 44 MHz C. 22 MHz D. 11 MHz

Last Answer : B. 44 MHz

The frequency of operation of a dipole antenna cut to length of 3.4 m. A. 42.9 MHz B. 61.3 MHz C. 38.5 MHz D. 53.5 MHz

Description : The frequency of operation of a dipole antenna cut to length of 3.4 m. A. 42.9 MHz B. 61.3 MHz C. 38.5 MHz D. 53.5 MHz

Last Answer : A. 42.9 MHz

How to maximize the skip distance? A. Using the smallest possible radiation angle and highest possible frequency B. Using the smallest possible radiation angle and lowest possible frequency C. Using the biggest possible radiation angle and highest possible frequency D. Using the biggest possible radiation angle and lowest possible frequency

Description : How to maximize the skip distance? A. Using the smallest possible radiation angle and highest possible frequency B. Using the smallest possible radiation angle and lowest possible frequency ... highest possible frequency D. Using the biggest possible radiation angle and lowest possible frequency

Last Answer : A. Using the smallest possible radiation angle and highest possible frequency

Skip distance can be maximized by using the ____ radiation angle possible and the ____ frequency that will be refracted at that angle. A. lowest, lowest B. lowest, highest C. highest, lowest D. highest, highest

Description : Skip distance can be maximized by using the ____ radiation angle possible and the ____ frequency that will be refracted at that angle. A. lowest, lowest B. lowest, highest C. highest, lowest D. highest, highest

Last Answer : B. lowest, highest

Where do the maximum current and minimum voltage values on a resonant Hertz dipole exist? A. Center of the antenna B. Near the end of the antenna C. Near the center of the antenna D. Ends of the antenna

Description : Where do the maximum current and minimum voltage values on a resonant Hertz dipole exist? A. Center of the antenna B. Near the end of the antenna C. Near the center of the antenna D. Ends of the antenna

Last Answer : A. Center of the antenna

Refers to a type of beam antenna which uses two or more straight elements arranged in line with each other. A. Dipole antenna B. Yagi antenna C. Whip antenna D. Rhombic antenna

Description : Refers to a type of beam antenna which uses two or more straight elements arranged in line with each other. A. Dipole antenna B. Yagi antenna C. Whip antenna D. Rhombic antenna

Last Answer : B. Yagi antenna

determining stresses in frames by methods of sections, the frame is divided into two parts by an imaginary section drawn in such a way as not to cut more than (A) Two members with unknown forces of the frame (B) Three members with unknown forces of the frame (C) Four members with unknown forces of the frame (D) Three members with known forces of the frame

Description : determining stresses in frames by methods of sections, the frame is divided into two parts by an imaginary section drawn in such a way as not to cut more than (A) Two members with unknown forces ... C) Four members with unknown forces of the frame (D) Three members with known forces of the frame

Last Answer : (B) Three members with unknown forces of the frame

Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Description : Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Last Answer : C. resistive load at the resonant frequency

Pick up the correct statement from the following: (A) The horizontal angle between magnetic meridian and true meridian at a place is called magnetic declination or variance of the compass (B) The imaginary lines which pass through points at which the magnetic declinations are equal at a given time are called isogonic lines (C) The isogonic lines through places at which the declination is zero are termedagonic lines (D) All the above

Description : Pick up the correct statement from the following: (A) The horizontal angle between magnetic meridian and true meridian at a place is called magnetic declination or variance of the compass (B) The ... lines through places at which the declination is zero are termedagonic lines (D) All the above

Last Answer : (D) All the above

How can intermodulation interference between two transmitters in close proximity reduced or eliminated? A. Through installing a band-pass filter in the antenna feed line B. Through installing terminated circulator or ferrite isolator in the feed line of the transmitter and duplexer C. By using a class C final amplifier with high driving power D. By installing a low-pass filter in the antenna feed line

Description : How can intermodulation interference between two transmitters in close proximity reduced or eliminated? A. Through installing a band-pass filter in the antenna feed line B. Through installing terminated circulator ... high driving power D. By installing a low-pass filter in the antenna feed line

Last Answer : A. Through installing a band-pass filter in the antenna feed line

Is the width of the range of wavelengths emitted by the light source a. Bandwidth b. Chromatic Dispersion c. Spectral width d. Beamwidth

Description : Is the width of the range of wavelengths emitted by the light source a. Bandwidth b. Chromatic Dispersion c. Spectral width d. Beamwidth

Last Answer : c. Spectral width

One of the following is not a reason for the use of an earth mat A. impossibility of a good ground connection B. provision of an earth for the antenna C. protection of personnel working underneath D. improvement of the radiation pattern of the antenna

Description : One of the following is not a reason for the use of an earth mat A. impossibility of a good ground connection B. provision of an earth for the antenna C. protection of personnel working underneath D. improvement of the radiation pattern of the antenna

Last Answer : C. protection of personnel working underneath

Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Description : Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Last Answer : D. To prevent re-radiation of the local oscillator

The advantage of using top loading in a shortened HF vertical antenna is A. lower quality factor B. greater structural strength C. higher losses D. improved radiation efficiency

Description : The advantage of using top loading in a shortened HF vertical antenna is A. lower quality factor B. greater structural strength C. higher losses D. improved radiation efficiency

Last Answer : D. improved radiation efficiency