What happens to the bandwidth of an antenna as it is shortened through the use of loading coils? A. It is increased B. It is decreased C. No change occurs D. It becomes flat

What happens to the bandwidth of an antenna as it is shortened through the use of loading
coils?
A. It is increased
B. It is decreased
C. No change occurs
D. It becomes flat
by

1 Answer

Answer :

A. It is increased
by

Related questions

For a shortened vertical antenna, where should a loading coil be placed to minimize losses and produce the most effective performance? A. As low as possible on the vertical radiator B. Near the center of the vertical radiator C. As close to the transmitter as possible D. At a voltage node

Description : For a shortened vertical antenna, where should a loading coil be placed to minimize losses and produce the most effective performance? A. As low as possible on the vertical radiator B. Near the center of the vertical radiator C. As close to the transmitter as possible D. At a voltage node

Last Answer : B. Near the center of the vertical radiator

The advantage of using top loading in a shortened HF vertical antenna is A. lower quality factor B. greater structural strength C. higher losses D. improved radiation efficiency

Description : The advantage of using top loading in a shortened HF vertical antenna is A. lower quality factor B. greater structural strength C. higher losses D. improved radiation efficiency

Last Answer : D. improved radiation efficiency

Top loading is used in an antenna in order to increase its ___________. A. input capacitance B. beamwidth C. bandwidth D. effective height

Description : Top loading is used in an antenna in order to increase its ___________. A. input capacitance B. beamwidth C. bandwidth D. effective height

Last Answer : D. effective height

If the length of an antenna is changed from 2.5 meters to 2.8 meters, its resonant frequency will A. increase B. depend on the velocity factor so the resonant frequency can either be increased or decreased C. will be unchanged D. decrease

Description : If the length of an antenna is changed from 2.5 meters to 2.8 meters, its resonant frequency will A. increase B. depend on the velocity factor so the resonant frequency can either be increased or decreased C. will be unchanged D. decrease

Last Answer : D. decrease

If the length of a Hertz dipole is decreased A. its resonant frequency will be lowered its distributed inductance will be increased B. its distributed inductance will be decreased C. its resonant frequency will be increased D. its distributed capacitance between the antenna and ground will be increased.

Description : If the length of a Hertz dipole is decreased A. its resonant frequency will be lowered its distributed inductance will be increased B. its distributed inductance will be decreased C. its ... frequency will be increased D. its distributed capacitance between the antenna and ground will be increased.

Last Answer : C. its resonant frequency will be increased

What is antenna bandwidth? A. Antenna length divided by the number of elements B. The angle between the half-power radiation points C. The angle formed between two imaginary lines drawn through D. The frequency range over which an antenna can be expected to operate satisfactorily

Description : What is antenna bandwidth? A. Antenna length divided by the number of elements B. The angle between the half-power radiation points C. The angle formed between two imaginary lines drawn through D. The frequency range over which an antenna can be expected to operate satisfactorily

Last Answer : D. The frequency range over which an antenna can be expected to operate satisfactorily

What is meant by the term antenna bandwidth A. Antenna length divided by the number of elements. B. The angle between the half-power radiation points C. The frequency range over which and antenna can be expected to perform well D. The angle formed between two imaginary line drawn through the ends of the elements

Description : What is meant by the term antenna bandwidth A. Antenna length divided by the number of elements. B. The angle between the half-power radiation points C. The frequency range over which and antenna ... perform well D. The angle formed between two imaginary line drawn through the ends of the elements

Last Answer : C. The frequency range over which and antenna can be expected to perform well

What is meant by the term radiation resistance for an antenna? A. The resistance in the trap coils to received signal B. An equivalent resistance that would dissipate the same amount of power as that radiated from an antenna C. The specific impedance of the antenna D. Losses in the antenna elements and feed line

Description : What is meant by the term radiation resistance for an antenna? A. The resistance in the trap coils to received signal B. An equivalent resistance that would dissipate the same amount of power as ... antenna C. The specific impedance of the antenna D. Losses in the antenna elements and feed line

Last Answer : B. An equivalent resistance that would dissipate the same amount of power as that radiated from an antenna

What happens to the beamwidth of an antenna as the gain is increased? A. The beamwidth increases geometrically as the gain is increased. B. The beamwidth increases arithmetically as the gain is increased. C. The beamwidth is essentially unaffected by the gain of the antenna. D. The beamwidth decreases as the gain is increased.

Description : What happens to the beamwidth of an antenna as the gain is increased? A. The beamwidth increases geometrically as the gain is increased. B. The beamwidth increases arithmetically as the gain is increased ... unaffected by the gain of the antenna. D. The beamwidth decreases as the gain is increased.

Last Answer : D. The beamwidth decreases as the gain is increased.

One of the following makes an antenna physically long but electrically short A. Adding L in series B. Adding C in series C. Top loading D. Both A and C

Description : One of the following makes an antenna physically long but electrically short A. Adding L in series B. Adding C in series C. Top loading D. Both A and C

Last Answer : B. Adding C in series

What is the estimated medium wind loading in the Philippines for antenna tower design? A. 300 kph B. 100 kph C. 200 kph D. 250 kph

Description : What is the estimated medium wind loading in the Philippines for antenna tower design? A. 300 kph B. 100 kph C. 200 kph D. 250 kph

Last Answer : C. 200 kph

Top loading is used in an antenna in order to increase its ______. A. practical height B. beamwidth C. effective height D. input capacitance

Description : Top loading is used in an antenna in order to increase its ______. A. practical height B. beamwidth C. effective height D. input capacitance

Last Answer : C. effective height

When speaking of antennas. ______ is a section which would be a complete antenna by itself. A. image B. top loading C. bay D. quarterwave

Description : When speaking of antennas. ______ is a section which would be a complete antenna by itself. A. image B. top loading C. bay D. quarterwave

Last Answer : C. bay

Known as the technique for adding a series inductor at or near the center of an antenna element in order to cancel the capacitive reactance of an antenna. A. Dipole B. Center loading C. Reflector D. loading coil

Description : Known as the technique for adding a series inductor at or near the center of an antenna element in order to cancel the capacitive reactance of an antenna. A. Dipole B. Center loading C. Reflector D. loading coil

Last Answer : D. loading coil

What makes an antenna physically long but electrically short? A. Top loading B. Adding C in series C. Adding L in series D. All of these

Description : What makes an antenna physically long but electrically short? A. Top loading B. Adding C in series C. Adding L in series D. All of these

Last Answer : B. Adding C in series

What is the estimated medium wind loading in the Philippines for antenna tower design? A. 200 kph B. 250 kph C. 300 kph D. 100 kph

Description : What is the estimated medium wind loading in the Philippines for antenna tower design? A. 200 kph B. 250 kph C. 300 kph D. 100 kph

Last Answer : A. 200 kph

______ is the measurement of a unilateral antenna properties of directivity A. Phase angle B. Antenna gain C. Beamwidth D. Bandwidth

Description : ______ is the measurement of a unilateral antenna properties of directivity A. Phase angle B. Antenna gain C. Beamwidth D. Bandwidth

Last Answer : C. Beamwidth

Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1.0MHz and the temperature is 20˚C, and that the receiver is connected to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

A helical antenna is used for satellite tracking because of ______. A. Broad bandwidth B. Good front-to-back C. Maneuverability D. Circular polarization

Description : A helical antenna is used for satellite tracking because of ______. A. Broad bandwidth B. Good front-to-back C. Maneuverability D. Circular polarization

Last Answer : D. Circular polarization

_______ is the horizontal pointing angle of an antenna. A. Right angle B. Angle of elevation C. Bandwidth D. Azimuth

Description : _______ is the horizontal pointing angle of an antenna. A. Right angle B. Angle of elevation C. Bandwidth D. Azimuth

Last Answer : D. Azimuth

When a capacitor is connected in series with a Marconi antenna? A. Antenna open circuit stops transmission B. An inductor of equal value must be added C. No change occurs to antenna D. Antenna resonant frequency increases

Description : When a capacitor is connected in series with a Marconi antenna? A. Antenna open circuit stops transmission B. An inductor of equal value must be added C. No change occurs to antenna D. Antenna resonant frequency increases

Last Answer : D. Antenna resonant frequency increases

A compression spring is made of music wire of 2 mm diameter having a shear strength and shear modulus of 800 Mpa and 80 Gpa respectively. The mean coil diameter is 20mm, free length is 40 mm, and the number of active coils is 10. If the mean coil diameter is reduced to 10 mm, the stiffness of the spring is approximately a. increased by 8 times b. decreased by 2 times c. increased by 2 times d. decreased by 8 times

Description : A compression spring is made of music wire of 2 mm diameter having a shear strength and shear modulus of 800 Mpa and 80 Gpa respectively. The mean coil diameter is 20mm, free length is 40 mm, and the number ... by 8 times b. decreased by 2 times c. increased by 2 times d. decreased by 8 times

Last Answer : a. increased by 8 times

The angle of elevation of the antenna beam is 20°. Calculate the transmission-path distance for an ionospheric transmission that utilizes a layer of virtual height 200 km. Use flat-earth approximation. A. 966 km B. 2100 km C. 1100 km D. 405 km

Description : The angle of elevation of the antenna beam is 20°. Calculate the transmission-path distance for an ionospheric transmission that utilizes a layer of virtual height 200 km. Use flat-earth approximation. A. 966 km B. 2100 km C. 1100 km D. 405 km

Last Answer : C. 1100 km

What happens to the strength of an electromagnet when the voltage in the coils of the solenoid is decreased?

Description : What happens to the strength of an electromagnet when the voltage in the coils of the solenoid is decreased?

Last Answer : The greater the current in the coil, the stronger the magnetic field will grow. Conversely, lowering the battery voltage decreases the current, weakening the field.

When the clearance above the obstruction is equal to the radii of even Fresnel zone at the point of reflection the RSL A. remains the same B. is above threshold C. is decreased D. is increased

Description : When the clearance above the obstruction is equal to the radii of even Fresnel zone at the point of reflection the RSL A. remains the same B. is above threshold C. is decreased D. is increased

Last Answer : C. is decreased

The purpose of stacking elements on an antenna. A. Sharper directional pattern B. increased gain C. Improved bandpass D. All of these

Description : The purpose of stacking elements on an antenna. A. Sharper directional pattern B. increased gain C. Improved bandpass D. All of these

Last Answer : D. All of these

If an antenna is too short for the wavelength being used, the effective length can be increased by adding: A. capacitance in series B. inductance in series C. resistance in parallel D. resistance in series

Description : If an antenna is too short for the wavelength being used, the effective length can be increased by adding: A. capacitance in series B. inductance in series C. resistance in parallel D. resistance in series

Last Answer : B. inductance in series

How much does the radiated power of an antenna increases if its current increased by 3.3 times? A. 6.6 times B. 3.3 times C. 10.89 times D. 9.9 times

Description : How much does the radiated power of an antenna increases if its current increased by 3.3 times? A. 6.6 times B. 3.3 times C. 10.89 times D. 9.9 times

Last Answer : C. 10.89 times

Flat footed camels can walk easily in sandy deserts because - (1) pressure on the sand is decreased by increasing the area of the surface in contact (2) pressure on the sand is increased by increasing the area of the surface in contact (3) pressure on the sand is decreased by decreasing the area of the surface in contact (4) pressure on the sand is increased by decreasing the area of the surface in contact

Description : Flat footed camels can walk easily in sandy deserts because - (1) pressure on the sand is decreased by increasing the area of the surface in contact (2) pressure on the sand is increased by ... in contact (4) pressure on the sand is increased by decreasing the area of the surface in contact

Last Answer : (1) pressure on the sand is decreased by increasing the area of the surface in contact Explanation: Camels have broad, flat, leathery pads with two toes on each foot. When the camel places its foot on ... the animal on loose sand in much the same way that a snowshoe helps a person walk on snow.

Flat footed camels can walk easily in sandy deserts because (1) pressure on the sand is decreased by increasing the area of the surface in contact (2) pressure on the sand is increased by increasing the area of the surface in contact (3) pressure on the sand is decreased by decreasing the area of the surface in contact (4) pressure on the sand is increased by decreasing the area of the surface in contact

Description : Flat footed camels can walk easily in sandy deserts because (1) pressure on the sand is decreased by increasing the area of the surface in contact (2) pressure on the sand is increased by increasing ... in contact (4) pressure on the sand is increased by decreasing the area of the surface in contact

Last Answer : pressure on the sand is decreased by increasing the area of the surface in contact

For a symmetrical two hinged parabolic arch, if one of the supports settles horizontally, then the horizontal thrust (A) Is increased (B) Is decreased (C) Remains unchanged (D) Becomes zero

Description : For a symmetrical two hinged parabolic arch, if one of the supports settles horizontally, then the horizontal thrust (A) Is increased (B) Is decreased (C) Remains unchanged (D) Becomes zero

Last Answer : (B) Is decreased

For a two-hinged arch, if one of the supports settles down vertically, then the horizontal thrust (A) Is increased (B) Is decreased (C) Remains unchanged (D) Becomes zero

Description : For a two-hinged arch, if one of the supports settles down vertically, then the horizontal thrust (A) Is increased (B) Is decreased (C) Remains unchanged (D) Becomes zero

Last Answer : (C) Remains unchanged

In a ferromagnetic material the state of flux density is as follows when external magnetic field is applied to it. (A) Increased (B) Decreased (C) Remains unchanged (D) Becomes zero

Description : In a ferromagnetic material the state of flux density is as follows when external magnetic field is applied to it. (A) Increased (B) Decreased (C) Remains unchanged (D) Becomes zero

Last Answer : (C) Remains unchanged

What is the primary advantage of DSBSC in AM? A. Reduce bandwidth over standard AM B. All of these C. It is simpler to transmit and receive than the standard AM D. No transmitter power is wasted in the carrier

Description : What is the primary advantage of DSBSC in AM? A. Reduce bandwidth over standard AM B. All of these C. It is simpler to transmit and receive than the standard AM D. No transmitter power is wasted in the carrier

Last Answer : D. No transmitter power is wasted in the carrier

The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the same bandwidth. A. Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Description : The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the ... . Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Last Answer : D. Residual noise level

How does the gain of a parabolic dish type antenna change when the operating frequency is doubled? A. Gain does not change B. Gain is multiplied by 0.707 C. Gain increases 6 dB D. Gain increases 3 dB

Description : How does the gain of a parabolic dish type antenna change when the operating frequency is doubled? A. Gain does not change B. Gain is multiplied by 0.707 C. Gain increases 6 dB D. Gain increases 3 dB

Last Answer : C. Gain increases 6 dB

One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency oscillation. A. Heating and expansion of oscillator coil B. DC and RF ac heating of resistors which cause change in values C. Heating of capacitor in the oscillatorD. Loose connections in the oscillator, amplifier, or antenna circuits.

Description : One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency ... capacitor in the oscillator D. Loose connections in the oscillator, amplifier, or antenna circuits.

Last Answer : D. Loose connections in the oscillator, amplifier, or antenna circuits.

Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections B. Power supply voltage changes C. Loose connections in the oscillator, amplifier, or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Description : Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections ... , or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Last Answer : D. DC and RF heating of resistors, causing then to change values.

How can intermodulation interference between two transmitters in close proximity reduced or eliminated? A. Through installing a band-pass filter in the antenna feed line B. Through installing terminated circulator or ferrite isolator in the feed line of the transmitter and duplexer C. By using a class C final amplifier with high driving power D. By installing a low-pass filter in the antenna feed line

Description : How can intermodulation interference between two transmitters in close proximity reduced or eliminated? A. Through installing a band-pass filter in the antenna feed line B. Through installing terminated circulator ... high driving power D. By installing a low-pass filter in the antenna feed line

Last Answer : A. Through installing a band-pass filter in the antenna feed line

De novo synthesis and oxidation of fatty acids differ in the following respect: (A) Synthesis occurs in cytosol and oxidation in mitochondria (B) Synthesis is decreased and oxidation increased by insulin (C) NADH is required in synthesis and FAD in oxidation (D) Malonyl CoA is formed during oxidation but not during synthesis

Description : De novo synthesis and oxidation of fatty acids differ in the following respect: (A) Synthesis occurs in cytosol and oxidation in mitochondria (B) Synthesis is decreased and oxidation increased by ... synthesis and FAD in oxidation (D) Malonyl CoA is formed during oxidation but not during synthesis

Last Answer : Answer : A

Renal glycosuria occurs due to (A) Increased filtration of glucose in glomeruli (B) Increased secretion of glucose by renal tubular cells (C) Decreased reabsorption of glucose by renal tubular cells (D) Increased conversion of glycogen into glucose in tubular cells

Description : Renal glycosuria occurs due to (A) Increased filtration of glucose in glomeruli (B) Increased secretion of glucose by renal tubular cells (C) Decreased reabsorption of glucose by renal tubular cells (D) Increased conversion of glycogen into glucose in tubular cells

Last Answer : Answer : D

. Vasodilatation occurs in: a. increased lactate concentration. b. decreased in skin c. increased hydrogen ions concentration d. increased in potassium concentration

Description : . Vasodilatation occurs in: a. increased lactate concentration. b. decreased in skin temperature c. increased hydrogen ions concentration d. increased in potassium concentration

Last Answer : increased in potassium concentration

Which of the following is not a way of minimizing if not eliminating noise? A. Use redundancy B. Increase transmitted power C. Reduce signaling rate D. Increase channel bandwidth

Description : Which of the following is not a way of minimizing if not eliminating noise? A. Use redundancy B. Increase transmitted power C. Reduce signaling rate D. Increase channel bandwidth

Last Answer : D. Increase channel bandwidth

Define loading?

Description : Define loading?

Last Answer : A large value of Rc cannot be used in a circuit since,a large value of resistance requires a large chip area.For large Rc, quiescent drop across it increases and hence a large power supply is required ... source can also be used as an active load for an amplifier to obtain a very large voltage gain.

The main benefit of light-wave communications over microwaves or any other communications media is a. Lower cost b. Better security c. Wider bandwidth d. Freedom from interference

Description : The main benefit of light-wave communications over microwaves or any other communications media is a. Lower cost b. Better security c. Wider bandwidth d. Freedom from interference

Last Answer : c. Wider bandwidth

Which of the following contributes to the broadening of laser emission bandwidth? a. Doppler shift of moving atoms and molecules b. Amplification within the laser medium c. Coherence of the laser light d. Optical pumping of the laser transition

Description : Which of the following contributes to the broadening of laser emission bandwidth? a. Doppler shift of moving atoms and molecules b. Amplification within the laser medium c. Coherence of the laser light d. Optical pumping of the laser transition

Last Answer : a. Doppler shift of moving atoms and molecules

Is the width of the range of wavelengths emitted by the light source a. Bandwidth b. Chromatic Dispersion c. Spectral width d. Beamwidth

Description : Is the width of the range of wavelengths emitted by the light source a. Bandwidth b. Chromatic Dispersion c. Spectral width d. Beamwidth

Last Answer : c. Spectral width

The bandwidth of optical fiber a. 900MHz b. 900PHz c. 900THz d. 900EHz

Description : The bandwidth of optical fiber a. 900MHz b. 900PHz c. 900THz d. 900EHz

Last Answer : c. 900THz

_____ is the amount of uncertainty in a system of symbols A. Bandwidth B. Enthalpy C. Entropy D. Quantum

Description : _____ is the amount of uncertainty in a system of symbols A. Bandwidth B. Enthalpy C. Entropy D. Quantum

Last Answer : C. Entropy

What is the typical bandwidth of a satellite band? A. 36 MHz B. 40 MHz C. 70 MHz D. 500 MHz

Description : What is the typical bandwidth of a satellite band? A. 36 MHz B. 40 MHz C. 70 MHz D. 500 MHz

Last Answer : D. 500 MHz