Why pistons are usually dished at top ?

Why pistons are usually dished at top ?
by

1 Answer

Answer :

Pistons are usually hollowed at top to (i) provide greater spa’e for combustion, (ii) increase surface for
flue gases to act upon, and (iii) better distribution of stresses.
by

Related questions

Engine pistons are usually made of aluminium alloy because it A. is lighter B. wears less C. Stronger D. absorbs shocks

Description : Engine pistons are usually made of aluminium alloy because it A. is lighter B. wears less C. Stronger D. absorbs shocks

Last Answer : ANSWER : A

Engine pistons are usually made of aluminium alloy as it a. is lighter b. wears less c. absorbs shocks d. is stronger

Description : Engine pistons are usually made of aluminium alloy as it a. is lighter b. wears less c. absorbs shocks d. is stronger

Last Answer : ANSWER a. is lighter

Will replacing pistons with flat top pistons in a 5.8 increase horse power?

Description : Will replacing pistons with flat top pistons in a 5.8 increase horse power?

Last Answer : Need answer

Is Donald Trump going to get what he dished out in the past (details inside )?

Description : Is Donald Trump going to get what he dished out in the past (details inside )?

Last Answer : Trump is a study in the armor afforded those of enormous wealth. His oafish demeanor and apparent indifference to ridicule from his betters renders him impervious to criticism as he bumps from one ... him. Again, is anyone here prepared to state where the man sits on the political spectrum?

Why are the pistons called that?

Description : Why are the pistons called that?

Last Answer : They are called this because Detroit is one of the biggestautomoblie producers in the country, and Pistons are found incars.

In which step of the four-stroke engine cycle does the heat from the combustion reaction causes the pistons to move?

Description : In which step of the four-stroke engine cycle does the heat from the combustion reaction causes the pistons to move?

Last Answer : combustion and expansion

How many championships do the Detroit Pistons have?

Description : How many championships do the Detroit Pistons have?

Last Answer : 3

A hydraulic accumulator comprises of (A) A storage device and a control valve (B) A cylinder and a plunger (C) Two pistons and two cylinders (D) A storage tank and a ram pump

Description : A hydraulic accumulator comprises of (A) A storage device and a control valve (B) A cylinder and a plunger (C) Two pistons and two cylinders (D) A storage tank and a ram pump

Last Answer : (B) A cylinder and a plunger

A CNC Lathe is usually a machine tool with Z axes is….. a.Line Joining origin and vertical movement b.Line perpendicular to Y axis c.Both A & B d.Line Joining Chuck centre & tail stock centre

Description : A CNC Lathe is usually a machine tool with Z axes is….. a.Line Joining origin and vertical movement b.Line perpendicular to Y axis c.Both A & B d.Line Joining Chuck centre & tail stock centre

Last Answer : d.Line Joining Chuck centre & tail stock centre

Car tyres are usually made of ?

Description : Car tyres are usually made of ?

Last Answer : Styrene-butadine rubber.

Why manholes in vessels are usually elliptical in shape ?

Description : Why manholes in vessels are usually elliptical in shape ?

Last Answer : Elliptical shape has minimum area of opening and thus plate is weakened the least. Further it is very convenient to insert and take out the cover plate from elliptical opening.

What Is The Potential Risk That Repair And Maintenance Work Usually Face?

Description : What Is The Potential Risk That Repair And Maintenance Work Usually Face?

Last Answer : The potential risk that repair and maintenance worker faces are: Faulty electrical: Risk of electrocuted always remains with repair and maintenance workers, if not equipped with electric-proof tools ... Dust: It potential risk for the workers specially working in woodworking or iron industries.

Mention What Are The Challenges That Maintenance And Repair Work Usually Face?

Description : Mention What Are The Challenges That Maintenance And Repair Work Usually Face?

Last Answer :  Unusual working condition like bad weather or low temperature  May have to work in an unusual shift  May have to work in a messy area  May sometimes be physically distressing and ... have to work in dangerous places like working at height or working with electrical appliances and wires.

Piston displacement is the volume displaced by the piston during one stroke and is usually expressed in 1. Cubic meter 2.cubic inches 3. Both of these 4. none of these

Description : Piston displacement is the volume displaced by the piston during one stroke and is usually expressed in 1. Cubic meter 2.cubic inches 3. Both of these 4. none of these

Last Answer :    <!-- [endif] -->ans-1

The disc is usually the preferred system as it takes and can handle obstacles much easier. A. Less power. C) More power B. Moderate power. D) None of the above

Description : The disc is usually the preferred system as it takes and can handle obstacles much easier. A. Less power. C) More power B. Moderate power. D) None of the above

Last Answer : Less power

Small labels can be found in appliances which usually a) Don‘t consume more energy c) don‘t have higher cost b) Don‘t consume less energy d) don‘t have high maintenance

Description : Small labels can be found in appliances which usually a) Don‘t consume more energy c) don‘t have higher cost b) Don‘t consume less energy d) don‘t have high maintenance

Last Answer : Don‘t consume more energy

Small label can be found in plants which usually don‘t consume ……….. energy. A) Less. C) More B) Medium. D) None of the above

Description : Small label can be found in plants which usually don‘t consume ……….. energy. A) Less. C) More B) Medium. D) None of the above

Last Answer : more

A waste heat recovery unit (WHRU) is an_________ that transfers heat from process outputs at high temperature to another part of the process for some purpose, usually increased efficiency. a) Energy recovery heat exchanger b) Energy recovery heat diffuser c) Both ‘a’ and ‘b’ d) None of the above

Description : A waste heat recovery unit (WHRU) is an_________ that transfers heat from process outputs at high temperature to another part of the process for some purpose, usually increased efficiency. a) Energy recovery heat exchanger b) Energy recovery heat diffuser c) Both ‘a’ and ‘b’ d) None of the above

Last Answer : Energy recovery heat exchanger

Work done in pushing a fluid across a boundary, Usually into or out of a system  a. Flow Work  b. Flow Energy  c. Both a & b  d. None of the above

Description : Work done in pushing a fluid across a boundary, Usually into or out of a system  a. Flow Work  b. Flow Energy  c. Both a & b  d. None of the above

Last Answer : Both a & b

Open system usually encloses which of the following devices?  A. Compressor  B. Turbine  C. Nozzle  D. All of the above

Description : Open system usually encloses which of the following devices?  A. Compressor  B. Turbine  C. Nozzle  D. All of the above

Last Answer : All of the above