Description : If the inputs to the diagram shown in the illustration were J=1, K=0, H=0, L=1, M=1, what logic levels would be indicated at points 'X' and 'Y' respectively? EL-0089 A. 0,0 B. 0,1 C. 1,0 D. 1,1
Last Answer : Answer: D
Description : If the inputs to the diagram shown in the illustration were J=1, K=1, H=0, L=1, M=1, what logic levels would be indicated at points 'X' and 'Y' respectively? EL-0089 A. 0,0 B. 0,1 C. 1,0 D. 1,1
Description : If the inputs to the diagram shown in the illustration were J=1, K=0, H=1, L=1, M=0, what logic levels would be indicated at points 'X' and 'Y' respectively? EL-0089 A. 0,0 B. 0,1 C. 1,0 D. 1,1
Last Answer : Answer: A
Description : If the outputs marked 'Q' of 'FF-A', 'FF-B' and 'FF-C' in the circuit shown in the illustration are at logic levels 0, 1, and 1 respectively, what levels are present at the 'NOT Q' outputs? EL-0087 A. 1, 0, and 1 B. 1, 0, and 0 C. 0, 0, and 1 D. 0, 1, and 1
Last Answer : Answer: B
Description : What type of logic circuit is indicated by the truth table shown in the illustration? EL-0072 A. OR B. AND C. NOR D. NAND
Description : The turns ratio of transforme 'A' shown in the illustration is four to one and all taps are evenly spaced. If 110 volts were applied to terminals 'X1' and 'X3', what would be indicated across 'H1' and 'H2'? EL-0082 A. 37.5 volts B. 55 volts C. 220 volts D. 440 volts
Last Answer : Answer: C
Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 220 volts were applied to terminals 'H1' & 'H2', what would be indicated across 'X1' & 'X4' with 'X2' & 'X3' connected and isolated? EL-0082 A. 55 volts B. 110 volts C. 220 volts D. 440 volts
Description : If the clock frequency to the circuit shown in the illustration were 100 kHz, what would be indicated at the output of 'FF-C'? EL-0087 A. 10.1 kHz B. 12.5 kHz C. 805 kHz D. 1010 kHz
Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 110 volts were applied to terminals 'X1,3' and 'X2,4', what would be indicated across 'H1' and 'H2'? EL-0082 A. 27.5 volts B. 55 volts C. 220 volts D. 440 volts
Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 440 volts were applied to terminals 'H1' & 'H2', what would be indicated across 'X1' & 'X4' with 'X2' & 'X3' connected and isolated? EL-0082 A. 110 volts B. 220 volts C. 880 volts D. 1760 volts
Description : If the clock frequency to the circuit shown in the illustration were 2 kHz, what would be indicated at the output of 'FF-C'? EL-0087 A. 250 Hz B. 666 Hz C. 6 kHz D. 16 kHz
Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 220 volts were applied to terminals 'H1' and 'H2', what would be indicated across 'X3' and 'X4'? EL-0082 A. 55 volts B. 110 volts C. 440 volts D. 880 volts
Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 440 volts were applied to terminals 'H1' and 'H2', what would be indicated across 'X1,3' and 'X2,4'? EL-0082 A. 55 volts B. 110 volts C. 220 volts D. 880 volts
Description : The turns ratio of device 'A' shown in the illustration is four to one and all taps are evenly spaced. If 110 volts were applied to terminals 'X1' and 'X3', what would be indicated across 'H1' and 'H2'? EL-0082 A. 37.5 volts B. 55 volts C. 220 volts D. 440 volts
Description : The turns ratio of device 'A' shown in the illustration is four to one and all the taps are equally spaced. If 120 volts were applied between 'X1' and 'X2', what would be indicated across 'H1' and 'H4'? EL-0082 A. 30 volts B. 120 volts C. 480 volts D. 1440 volts
Description : A ground detection system is shown in the illustration for a three-phase ungrounded distribution system. Which of the following statements describes the conditions indicated if a full ground occurs in line 'A'? EL-0009 A ... . D. Lamp 'A' will go out and Lamps 'B' and 'C' will burn brightly.
Description : Which of the devices listed is indicated by the electronic symbol lettered as 'A', shown in the illustration? EL-0016 A. Thyristor B. Diode C. Capacitor D. Transistor
Description : When replacing component 'B' of the circuit shown in the illustration, it is important to know that ____________. EL-0081 A. it is polarity sensitive and must be inserted as indicated on its ... provide the capacitor's initial charge D. it must match the circuit voltage and component 'C' wattage
Description : The illustrated test is being conducted on the motor shown in the illustration, if the lamp lights dimly then ________. EL-0027 A. the bulb needs to be changed to one with a higher wattage rating B. ... D. a ground or partial ground is indicated, a check with a megger should confirm the lamp test
Description : As shown in the illustration, what is the meaning of the numbers in brackets [ ] at location '31/33U'? EL-0100 A. Four separate devices with these part numbers feed signals into this point. ... continues on those four pages and connects to devices at the indicated coordinates. D. None of the above.
Description : Which of the devices listed is indicated by the symbols lettered 'A' to 'F', shown in the illustration? EL-0016 A. Diodes B. Linear inductors C. Capacitors D. Transistors
Description : When changing out component 'B' of the circuit shown in the illustration, it is important to know that ____________. EL-0081 A. it is polarity sensitive and must be inserted as indicated on its ... provide the capacitor's initial charge D. it must match the circuit voltage and component 'C' wattage
Description : What is indicated by gradual blackening at the ends of component 'C' shown in the illustration? EL-0081 A. The unit is in danger of exploding. B. The tube is nearing the end of its useful life. C. The circuit voltage is too high. D. The circuit current is too high.
Description : As shown in the illustration, which of the listed types of motor controllers and starters is indicated? EL-0012 A. Across-the-line B. Capacitor C. Autotransformer D. Part-winding
Description : If the values of 'C' and 'R' shown in the illustration were 1 microfarad and 100 kOhms respectively, at what listed time would 'C' be considered fully charged? EL-0086 A. 0.1 second B. 0.2 second C. 0.5 second D. 5 seconds
Description : If the values of 'C' and 'R' shown in the illustration were 1 microfarad and 3 Megohms respectively, at what listed time would 'C' be considered fully charged? EL-0086 A. 0.33 second B. 3 seconds C. 6 seconds D. 15 seconds
Description : If the values of C and R shown in the illustration were 1-microfarad and 3- Megohms respectively, which of the listed intervals would equal one 'time constant'? EL-0086 A. 0.33 second B. 3 seconds C. 6 seconds D. 15 seconds
Description : What type of circuit is on card 'A0AA2' at coordinate '29Q' shown in the illustration? EL-0099 A. Operational amplifier B. Digital logic inverter C. Square wave pulse generator D. Binary counter
Description : As shown in the illustration, which set of conditions, evident to the operator and the 'setpoint module' respectively, will result in a high exhaust temperature alarm on the 'starboard main engine'? EL-0094 A. 50°F and 3.3 volts B. 180°F and 6.0 volts C. 750°F and 0-10 volts D. 900°F and 7.5 volts
Description : As shown in the illustration, part 'X' of the diagram is known as a/an _____________. EL-0052 A. commutator B. interpole C. starting pole D. auxiliary pole
Description : In the schematic diagram of the DC compound generator shown in the illustration, the positive ammeter reading is 500 amps and the negative ammeter reading is 475 amps. What is the current flow through the neutral bus? EL-0037 A. 0 amp B. 12.5 amp C. 25 amp D. 975 amp
Description : Batteries 'A' and 'B' shown in the illustration are 6 volts each and batteries 'C' and 'D' are 24 volts each. If 'A' and 'B' were reconnected to be in series-opposing to 'C' and 'D' ... at the top terminal C. 30 volts, negative at the bottom terminal D. 30 volts, positive at the bottom terminal
Description : For console circuit card 'LLEA' as shown in the illustration at coordinates '63R/S', the input(s) and output(s) are respectively on pin numbers ____________. EL-0100 A. '5' and '3' & '4' B. '2' & '3' and '5' & '6' C. '5' & '6' and '2' & '3' D. '3' & '4' and '5'
Description : When 'selector switch' 'SEL8' shown in the illustration is in the 'TEST' position, contacts '3,4' and '7,8' are respectively ____________. EL-0100 A. open; closed B. closed; open C. open; open D. closed; closed
Description : When 'selector switch' 'SEL8' shown in the illustration is in the 'OFF' position, contacts '3,4' and '7,8' are respectively ____________. EL-0100 A. open; closed B. closed; open C. open; open D. closed; closed
Description : When 'selector switch' 'SEL8' shown in the illustration is in the 'ON' position, contacts '3,4' and '7,8' are respectively ______________. EL-0100 A. open; closed B. closed; open C. open; open D. closed; closed
Description : Which of the diagrams shown in the illustration, indicates the highest induced voltage? EL-0028 A. Diagram 'A' only B. Diagram 'B' only C. Both diagrams 'A' and 'C' D. Both diagrams 'B' and 'D'
Description : The wiring diagram for the motor starting circuit shown in the illustration indicates ______________. EL-0007 A. resistance starting B. reduced voltage starting C. low voltage protection D. low voltage release
Description : Which of the following statements is true concerning the motor controller diagram shown in the illustration? EL-0023 A. Terminal 'T2' is hot only on high speed. B. Both indicating lights will be lit on ... high speed operation only. D. 'L2' is always connected to 'T2' whenever the motor is running.
Description : The electrical diagram shown in the illustration shows _____________. EL-0021 A. 'R1', 'R2', and 'R3' are connected is series B. 'R1', 'R2', and 'R3' are connected in parallel C. the voltages measured across ... if 'R1', 'R2' and 'R3' have different values D. the total resistance equals R1 + R2 + R3
Description : The electrical diagram shown in the illustration represents a ___________. EL-0054 A. series-wound motor B. shunt-wound motor C. compound-wound motor D. flat-compounded motor
Description : The electrical diagram shown in the illustration is used to depict a/an ____________. EL-0015 A. resistance circuit B. inductive circuit C. stepdown circuit D. capacitive circuit
Description : The schematic diagram shown in the illustration uses symbol 'A' to represent a/an _________. EL-0011 A. non-renewable fuse link B. circuit breaker coil C. overload relay coil D. thermal overload heater
Description : The diagram shown in the illustration represents a/an _____________. EL-0082 A. stepup transformer B. magnetic amplifier C. autotransformer D. Scott-connected transformer
Description : Which component is responsible for energizing solenoid 'B1-B2' and releasing the brake for the winch motor shown in the illustration? EL-0102 A. Contactor '3M' B. A spring not shown in the schematic diagram C. Resistor 'B2-R1' D. Relay 'FR-B.O.'
Description : The contacts operated by the D.C. relay coil shown in the illustration are located in the schematic diagram prints at coordinates ____________. EL-0100 A. '41Y' on this page B. '52M52M' and '52H35M' C. '57R' on this page D. '52N' on page '57R'
Description : The schematic diagram shown in the illustration represents which of the listed solid-state circuits? EL-0069 A. Bridge rectifier B. Magnetic amplifier C. Flip-flop generator D. Cathodic amplifier
Description : In the pitch control diagram shown in the illustration, what are the present plant operating conditions? EL-0095 A. One engine is on the line, cruise mode is selected and the engine room is in control. ... . D. Both engines are on line, maneuvering mode is selected and the engine room is in control.
Description : What are the plant conditions existing in the 'engine speed control' diagram shown in the illustration? EL-0096 A. The Bridge is in control in the 'auto. maneuver' mode. B. The Engine Room is in control in ... in the 'auto. split' mode. D. The Engine Room is in control in the 'auto. maneuver' mode.
Description : Figure 'A' of the diagram shown in the illustration represents a ______________. EL-0092 A. differential transformer B. saturable reactor C. synchro system D. magnetic amplifier