As shown in the illustration, which set of conditions, evident to the operator and the 'setpoint module' respectively, will result in a high exhaust temperature alarm on the 'starboard main engine'? EL-0094 A. 50°F and 3.3 volts B. 180°F and 6.0 volts C. 750°F and 0-10 volts D. 900°F and 7.5 volts

As shown in the illustration, which set of conditions, evident to the operator and the 'setpoint module' respectively, will result in a high exhaust temperature alarm on the 'starboard main engine'? EL-0094 A. 50°F and 3.3 volts B. 180°F and 6.0 volts C. 750°F and 0-10 volts D. 900°F and 7.5 volts
by

1 Answer

Answer :

Answer: D
by

Related questions

An open-circuit fault between the pressure switch and the 'annunciator module' shown in the illustration would cause the alarm circuit to react in the same manner as if ___________. EL-0094 A. 3.5 volts were applied to the 'setpoint module' B. 'reduction gear lube oil pressure' fell below switch setting C. 50 PSI were applied to the 'setpoint module' D. the pressure switch closed

Description : An open-circuit fault between the pressure switch and the 'annunciator module' shown in the illustration would cause the alarm circuit to react in the same manner as if ___________. EL-0094 A. 3.5 ... below switch setting C. 50 PSI were applied to the 'setpoint module' D. the pressure switch closed

Last Answer : Answer: B

What is the purpose of the 'annunciator module' (6000F35) shown in the illustration? EL-0094 A. Provide an input to the setpoint module. B. Drive the alarm lamp and, through the controller, the horn. C. Deliver +5 and +24 volts to their respective power supplies. D. Connect 24 volts to both sides of the horn.

Description : What is the purpose of the 'annunciator module' (6000F35) shown in the illustration? EL-0094 A. Provide an input to the setpoint module. B. Drive the alarm lamp and, through the controller, the horn. ... and +24 volts to their respective power supplies. D. Connect 24 volts to both sides of the horn.

Last Answer : Answer: B

What is the purpose of either 'setpoint module' (6000F090/030) shown in the illustration? EL-0094 A. Program the 'signal conditioner' as to how to vary its input. B. Supply 0 - 10 volts to the 'signal conditioner'. C. Initiate logging of measured information at set intervals; for example, each hour. D. Obtain an input from the 'signal conditioner' and, if outside set limits, signals the 'annunciator'.

Description : What is the purpose of either 'setpoint module' (6000F090/030) shown in the illustration? EL-0094 A. Program the 'signal conditioner' as to how to vary its input. B. Supply 0 - 10 volts to ... . Obtain an input from the 'signal conditioner' and, if outside set limits, signals the 'annunciator'.

Last Answer : Answer: D

What type of service is NOT provided by the circuit shown in the illustration? EL-0094 A. Logging of engine order signals from the bridge. B. Printed record of alarms as they occur. C. Visual metering of temperature and pressure conditions. D. Periodic recording of pressure and temperature conditions.

Description : What type of service is NOT provided by the circuit shown in the illustration? EL-0094 A. Logging of engine order signals from the bridge. B. Printed record of alarms as they ... . Visual metering of temperature and pressure conditions. D. Periodic recording of pressure and temperature conditions.

Last Answer : Answer: A

The +5 volt regulated power supply shown in the illustration is fed directly from the _______________. EL-0094 A. 115 volt AC bus B. Annunciator Module C. +24 volt supply D. Annunciator Controller

Description : The +5 volt regulated power supply shown in the illustration is fed directly from the _______________. EL-0094 A. 115 volt AC bus B. Annunciator Module C. +24 volt supply D. Annunciator Controller

Last Answer : Answer: C

Which plant parameters shown in the illustration would produce an alarm if they exceeded preset values? EL-0094 A. SME #7 CYL. EXH. and L.O. TO RDCN. GR. B. L.O. PRESS. TO MN. ENG. and PME #3 MN. BRG. C. L.O. PRESS. TO MN. ENG. and L.O. TO RDCN. GR. D. PME #3 MN. BRG. and SME #7 CYL. EXH.

Description : Which plant parameters shown in the illustration would produce an alarm if they exceeded preset values? EL-0094 A. SME #7 CYL. EXH. and L.O. TO RDCN. GR. B. L.O. PRESS. TO MN. ENG. and PME #3 MN. BRG. C. L.O. PRESS. TO MN. ENG. and L.O. TO RDCN. GR. D. PME #3 MN. BRG. and SME #7 CYL. EXH.

Last Answer : Answer: D

Which plant parameters shown in the illustration would produce an alarm if they fell below preset values? EL-0094 A. SME #7 CYL. EXH. and L.O. PRESS. TO RDCN. GR. B. L.O. PRESS TO MN. ENG. and PME #3 MN. BRG. C. L.O. PRESS. TO MN. ENG and L.O. PRESS. TO RDCN. GR. D. PME #3 MN. BRG. and SME #7 CYL. EXH.

Description : Which plant parameters shown in the illustration would produce an alarm if they fell below preset values? EL-0094 A. SME #7 CYL. EXH. and L.O. PRESS. TO RDCN. GR. B. L.O. PRESS TO MN. ENG. and PME #3 MN. BRG. C. ... . TO MN. ENG and L.O. PRESS. TO RDCN. GR. D. PME #3 MN. BRG. and SME #7 CYL. EXH.

Last Answer : Answer: C

Batteries 'A' and 'B' shown in the illustration are 6 volts each and batteries 'C' and 'D' are 24 volts each. If 'A' and 'B' were reconnected to be in series-opposing to 'C' and 'D' respectively, the result would be _______________. EL-0039 A. 18 volts, negative at the top terminal B. 18 volts, positive at the top terminal C. 30 volts, negative at the bottom terminal D. 30 volts, positive at the bottom terminal

Description : Batteries 'A' and 'B' shown in the illustration are 6 volts each and batteries 'C' and 'D' are 24 volts each. If 'A' and 'B' were reconnected to be in series-opposing to 'C' and 'D' ... at the top terminal C. 30 volts, negative at the bottom terminal D. 30 volts, positive at the bottom terminal

Last Answer : Answer: A

Which sensor shown in the illustration develops its own conditioning and point setting and 'reports' directly to the 'annunciator'? EL-0094 A. Transducer B. Resistance Temperature Detector (RTD) C. Pressure Switch D. Thermocouple

Description : Which sensor shown in the illustration develops its own conditioning and point setting and 'reports' directly to the 'annunciator'? EL-0094 A. Transducer B. Resistance Temperature Detector (RTD) C. Pressure Switch D. Thermocouple

Last Answer : Answer: C

In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 1 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal ... 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: A

Batteries 'A' and 'B' shown in the illustration are 6 volts each and batteries 'C' and 'D' are 24 volts each. If 'A' were connected in series-opposing to 'C' and 'B' was similarly connected to'D', the result would be _______________. EL-0039 A. 18 volts, negative at the top terminal B. 18 volts, positive at the top terminal C. 30 volts, negative at the bottom terminal D. 30 volts, positive at the bottom terminal

Description : Batteries 'A' and 'B' shown in the illustration are 6 volts each and batteries 'C' and 'D' are 24 volts each. If 'A' were connected in series-opposing to 'C' and 'B' was similarly ... the top terminal C. 30 volts, negative at the bottom terminal D. 30 volts, positive at the bottom terminal

Last Answer : Answer: A

The sensor connected to 'signal conditioner' (6000F125) shown in the illustration is a/an ______________. EL-0094 A. thermocouple B. transducer C. inverter D. RTD

Description : The sensor connected to 'signal conditioner' (6000F125) shown in the illustration is a/an ______________. EL-0094 A. thermocouple B. transducer C. inverter D. RTD

Last Answer : Answer: B

The sensor connected to 'signal conditioner' (6000AH170) shown in the illustration is a/an _____________. EL-0094 A. thermocouple B. transducer C. inverter D. RTD

Description : The sensor connected to 'signal conditioner' (6000AH170) shown in the illustration is a/an _____________. EL-0094 A. thermocouple B. transducer C. inverter D. RTD

Last Answer : Answer: A

The sensor connected to 'signal conditioner' (6000F085) shown in the illustration is a/an ______________. EL-0094 A. thermocouple B. transducer C. inverter D. RTD

Description : The sensor connected to 'signal conditioner' (6000F085) shown in the illustration is a/an ______________. EL-0094 A. thermocouple B. transducer C. inverter D. RTD

Last Answer : Answer: D

How many different D.C. voltages are required to operate the circuit shown in the illustration? EL-0094 A. Two B. Three C. Four D. Five

Description : How many different D.C. voltages are required to operate the circuit shown in the illustration? EL-0094 A. Two B. Three C. Four D. Five

Last Answer : Answer: C

In an emergency, the fastest way to interrupt power and stop the winch shown in the illustration is for the ____________. EL-0102 A. mate to open the disconnect switch at 'L1' and 'L2' B. winch operator to open the 'safe switch' at the 'master switch' C. engine room watch engineer to open the winch circuit breaker D. electrician to open the test link at the controller

Description : In an emergency, the fastest way to interrupt power and stop the winch shown in the illustration is for the ____________. EL-0102 A. mate to open the disconnect switch at 'L1' and 'L2' B. ... watch engineer to open the winch circuit breaker D. electrician to open the test link at the controller

Last Answer : Answer: B

Considering the function of the circuit shown in the illustration, what is the purpose of supplying the thrust lever potentiometers with both (+) and (-) 15 volts? EL-0095 A. To select which lever (bridge or engine room) is active. B. So the circuit can differentiate between ahead and astern commands. C. To provide an alternate voltage supply if the other fails. D. So as to automatically select the position of Relay #

Description : Considering the function of the circuit shown in the illustration, what is the purpose of supplying the thrust lever potentiometers with both (+) and (-) 15 volts? EL-0095 A. To select which ... alternate voltage supply if the other fails. D. So as to automatically select the position of Relay #

Last Answer : Answer: B

What will be the total output voltage if four 1.5 volt batteries are connected in a series-parallel arrangement as shown in the illustration? EL-0039 A. 1.5 volts B. 3.0 volts C. 4.5 volts D. 6.0 volts

Description : What will be the total output voltage if four 1.5 volt batteries are connected in a series-parallel arrangement as shown in the illustration? EL-0039 A. 1.5 volts B. 3.0 volts C. 4.5 volts D. 6.0 volts

Last Answer : Answer: B

What is the calculated voltage at the positive and negative terminals of the battery shown in the illustration if each cell has a voltage of 1.5 volts? EL-0034 A. 1.5 volts B. 3.0 volts C. 6.0 volts D. 12.0 volts

Description : What is the calculated voltage at the positive and negative terminals of the battery shown in the illustration if each cell has a voltage of 1.5 volts? EL-0034 A. 1.5 volts B. 3.0 volts C. 6.0 volts D. 12.0 volts

Last Answer : Answer: A

Which of the listed conditions occur when '4th point lower' is selected on the winch shown in the illustration? EL-0102 A. Master switch contacts '3', '4', '6', '8', '9', & '10' close. B. Contactors '2, 3, & 4M' and '1A' pick up. C. Master switch contacts '5', '6', '7', '8', and '9' close. D. Contactors '1 & 3M' and '1, 2, & 3A' pick up.

Description : Which of the listed conditions occur when '4th point lower' is selected on the winch shown in the illustration? EL-0102 A. Master switch contacts '3', '4', '6', '8', '9', & '10' close. B. Contactors '2, 3, & 4M' and ' ... , '7', '8', and '9' close. D. Contactors '1 & 3M' and '1, 2, & 3A' pick up.

Last Answer : Answer: B

If the 'E/P converter' shown in the illustration operated on a range of 1-9 volts and 6-30 PSI, a 5 volt input would yield ______________. EL-0096 A. 9 PSI B. 15 PSI C. 18 PSI D. 24 PSI

Description : If the 'E/P converter' shown in the illustration operated on a range of 1-9 volts and 6-30 PSI, a 5 volt input would yield ______________. EL-0096 A. 9 PSI B. 15 PSI C. 18 PSI D. 24 PSI

Last Answer : Answer: C

The 'pitch controller module' shown in the illustration is fed the actual pitch position of the propeller from the _____________. EL-0095 A. 'pitch meter' B. 'pitch feedback potentiometer' C. #5 relay position D. pitch error signal

Description : The 'pitch controller module' shown in the illustration is fed the actual pitch position of the propeller from the _____________. EL-0095 A. 'pitch meter' B. 'pitch feedback potentiometer' C. #5 relay position D. pitch error signal

Last Answer : Answer: B

What would be the power consumed in the combined parallel section of the circuit shown in the illustration if the source were 30 volts and the resistance for R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms? EL-0032 A. 5 watts B. 10 watts C. 20 watts D. 40 watts

Description : What would be the power consumed in the combined parallel section of the circuit shown in the illustration if the source were 30 volts and the resistance for R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms? EL-0032 A. 5 watts B. 10 watts C. 20 watts D. 40 watts

Last Answer : Answer: C

What power would be consumed by the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms? EL-0032 A. 5 watts B. 10 watts C. 20 watts D. 40 watts

Description : What power would be consumed by the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms? EL-0032 A. 5 watts B. 10 watts C. 20 watts D. 40 watts

Last Answer : Answer: D

What power would be consumed in EACH of the branch resistors of the circuit shown in the illustration if the source is 30 volts, the resistance for R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 watts B. 10 watts C. 20 watts D. 40 watts

Description : What power would be consumed in EACH of the branch resistors of the circuit shown in the illustration if the source is 30 volts, the resistance for R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 watts B. 10 watts C. 20 watts D. 40 watts

Last Answer : Answer: B

What would be the voltage drop across the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts

Description : What would be the voltage drop across the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts

Last Answer : Answer: C

What would be the voltage drop across the parallel branches of the circuit shown in the illustration if the source is 30 volts the resistance for R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts

Description : What would be the voltage drop across the parallel branches of the circuit shown in the illustration if the source is 30 volts the resistance for R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts

Last Answer : Answer: B

What would be the total current flowing in the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 1 amp B. 2 amps C. 5 amps D. 15 amps

Description : What would be the total current flowing in the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 1 amp B. 2 amps C. 5 amps D. 15 amps

Last Answer : Answer: B

The 'safe switch' of the winch controller shown in the illustration is operated _______________. EL-0102 A. through the master switch handle B. when heater circuit current is high C. by contactor coil 'FR' D. manually by the winch operator

Description : The 'safe switch' of the winch controller shown in the illustration is operated _______________. EL-0102 A. through the master switch handle B. when heater circuit current is high C. by contactor coil 'FR' D. manually by the winch operator

Last Answer : Answer: D

As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 110 ohms, and R2 is 10 kohms what is the voltage measured across R1 EL-0036 A. 11.86 volts B. .131 volts C. 12 volts D. .673 volts

Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 110 ohms, and R2 is 10 kohms what is the voltage measured across R1 EL-0036 A. 11.86 volts B. .131 volts C. 12 volts D. .673 volts

Last Answer : Answer: B

What would be the total power consumed in the circuit shown in the illustration if the source is 30 volts the resistance for R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms? EL-0032 A. 10 watts B. 40 watts C. 45 watts D. 60 watts

Description : What would be the total power consumed in the circuit shown in the illustration if the source is 30 volts the resistance for R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms? EL-0032 A. 10 watts B. 40 watts C. 45 watts D. 60 watts

Last Answer : Answer: D

If the total source voltage of the three-wire distribution system shown in the illustration is 240 volts, what is the voltage across load L5? [ NOTE: Kirchhoff's voltage and current laws apply ] EL-0075 A. 110.4 volts B. 112.2 volts C. 113.0 volts D. 114.8 volts

Description : If the total source voltage of the three-wire distribution system shown in the illustration is 240 volts, what is the voltage across load L5? [ NOTE: Kirchhoff's voltage and current laws apply ] EL-0075 A. 110.4 volts B. 112.2 volts C. 113.0 volts D. 114.8 volts

Last Answer : Answer: D

If the total source voltage of the three-wire distribution system shown in the illustration is 240 volts, what is the voltage across load L2? [NOTE: Kirchhoff's voltage and current laws apply.] EL-0075 A. 110.4 volts B. 112.2 volts C. 113.0 volts D. 114.8 volts

Description : If the total source voltage of the three-wire distribution system shown in the illustration is 240 volts, what is the voltage across load L2? [NOTE: Kirchhoff's voltage and current laws apply.] EL-0075 A. 110.4 volts B. 112.2 volts C. 113.0 volts D. 114.8 volts

Last Answer : Answer: C

If the total source voltage of the three-wire distribution system shown in the illustration is 240 volts, what is the voltage across load L3? [NOTE: Kirchhoff's voltage and current laws apply.] EL-0075 A. 110.4 volts B. 112.2 volts C. 113.0 volts D. 114.8 volts

Description : If the total source voltage of the three-wire distribution system shown in the illustration is 240 volts, what is the voltage across load L3? [NOTE: Kirchhoff's voltage and current laws apply.] EL-0075 A. 110.4 volts B. 112.2 volts C. 113.0 volts D. 114.8 volts

Last Answer : Answer: B

If the total source voltage of the three-wire distribution system shown in the illustration is 240 volts, what is the voltage across load L4? EL-0075 A. 110.4 volts B. 112.2 volts C. 113.0 volts D. 114.8 volts

Description : If the total source voltage of the three-wire distribution system shown in the illustration is 240 volts, what is the voltage across load L4? EL-0075 A. 110.4 volts B. 112.2 volts C. 113.0 volts D. 114.8 volts

Last Answer : Answer: A

When the circuit shown in the illustration is operating correctly, the voltage at the reference electrode will be kept in the optimum range of ____________. EL-0090 A. 0.01 - 0.05 volt B. 0.80 - 0.85 volt C. 35 - 60 volts D. 100 - 115 volts

Description : When the circuit shown in the illustration is operating correctly, the voltage at the reference electrode will be kept in the optimum range of ____________. EL-0090 A. 0.01 - 0.05 volt B. 0.80 - 0.85 volt C. 35 - 60 volts D. 100 - 115 volts

Last Answer : Answer: B

As shown in the illustration, which of the following conditions will occur as a result of a momentary loss of power? EL-0017 A. The motor will automatically restart when power is restored. B. 'H-4' will open, necessitating a manual restarting of the motor. C. '10L' and '20L' will open, necessitating a manual restarting of the motor. D. 'A-1' or 'A-2' will open, necessitating a manual restarting of the motor.

Description : As shown in the illustration, which of the following conditions will occur as a result of a momentary loss of power? EL-0017 A. The motor will automatically restart when power is restored. B. 'H-4' will open, ... the motor. D. 'A-1' or 'A-2' will open, necessitating a manual restarting of the motor.

Last Answer : Answer: B

Which set of truth table input signals will result in an output signal value of 1 from the 'AND' gate as shown in the illustration? EL-0035 A. 1-Jan B. Jan-00 C. 0-1 D. 0-0

Description : Which set of truth table input signals will result in an output signal value of 1 from the 'AND' gate as shown in the illustration? EL-0035 A. 1-Jan B. Jan-00 C. 0-1 D. 0-0

Last Answer : Answer: A

As shown in the illustration, which set of truth table input signals will result in an output signal at point 'Y'? EL-0035 A. 0-0 B. 0-1 C. Jan-00 D. 1-Jan

Description : As shown in the illustration, which set of truth table input signals will result in an output signal at point 'Y'? EL-0035 A. 0-0 B. 0-1 C. Jan-00 D. 1-Jan

Last Answer : Answer: D

In the pitch control diagram shown in the illustration, what are the present plant operating conditions? EL-0095 A. One engine is on the line, cruise mode is selected and the engine room is in control. B. One engine is on the line, maneuvering mode is selected and the bridge is in control. C. Both engines are on line, cruise mode is selected and the bridge is in control. D. Both engines are on line, maneuvering mode is selected and the engine room is in control.

Description : In the pitch control diagram shown in the illustration, what are the present plant operating conditions? EL-0095 A. One engine is on the line, cruise mode is selected and the engine room is in control. ... . D. Both engines are on line, maneuvering mode is selected and the engine room is in control.

Last Answer : Answer: D

What are the plant conditions existing in the 'engine speed control' diagram shown in the illustration? EL-0096 A. The Bridge is in control in the 'auto. maneuver' mode. B. The Engine Room is in control in the 'cruise split' mode. C. The Bridge is in control in the 'auto. split' mode. D. The Engine Room is in control in the 'auto. maneuver' mode.

Description : What are the plant conditions existing in the 'engine speed control' diagram shown in the illustration? EL-0096 A. The Bridge is in control in the 'auto. maneuver' mode. B. The Engine Room is in control in ... in the 'auto. split' mode. D. The Engine Room is in control in the 'auto. maneuver' mode.

Last Answer : Answer: D

Which of the listed conditions occur when selection is made for 'third point hoist' on the winch shown in the illustration? EL-0102 A. Master switch contacts '5', '6', '7', '8', and '9' close. B. Contactors '2M', '3M', '4M' and '1A' pick up. C. Contactors '1M', 3M', '1A' and '2A' drop out. D. Master switch contacts '3','4', '6', '8', and '9' close.

Description : Which of the listed conditions occur when selection is made for 'third point hoist' on the winch shown in the illustration? EL-0102 A. Master switch contacts '5', '6', '7', '8', and '9' close. B. Contactors '2M', ' ... ' and '2A' drop out. D. Master switch contacts '3','4', '6', '8', and '9' close.

Last Answer : Answer: D

The turns ratio of transforme 'A' shown in the illustration is four to one and all taps are evenly spaced. If 110 volts were applied to terminals 'X1' and 'X3', what would be indicated across 'H1' and 'H2'? EL-0082 A. 37.5 volts B. 55 volts C. 220 volts D. 440 volts

Description : The turns ratio of transforme 'A' shown in the illustration is four to one and all taps are evenly spaced. If 110 volts were applied to terminals 'X1' and 'X3', what would be indicated across 'H1' and 'H2'? EL-0082 A. 37.5 volts B. 55 volts C. 220 volts D. 440 volts

Last Answer : Answer: C

The dry-cell batteries, when connected as shown in the illustration, would produce ____________. EL-0070 A. 1.5 volts B. 2.5 volts C. 3.5 volts D. 4.5 volts

Description : The dry-cell batteries, when connected as shown in the illustration, would produce ____________. EL-0070 A. 1.5 volts B. 2.5 volts C. 3.5 volts D. 4.5 volts

Last Answer : Answer: A

The turns ratio of device 'B' shown in the illustration is two to one (total). If 110 volts were applied to terminals 'X1,3' and 'X2,4', what would be indicated across 'H1' and 'H2'? EL-0082 A. 27.5 volts B. 55 volts C. 220 volts D. 440 volts

Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 110 volts were applied to terminals 'X1,3' and 'X2,4', what would be indicated across 'H1' and 'H2'? EL-0082 A. 27.5 volts B. 55 volts C. 220 volts D. 440 volts

Last Answer : Answer: D

The turns ratio of device 'A' shown in the illustration is four to one and all taps are evenly spaced. If 110 volts were applied to terminals 'X1' and 'X3', what would be indicated across 'H1' and 'H2'? EL-0082 A. 37.5 volts B. 55 volts C. 220 volts D. 440 volts

Description : The turns ratio of device 'A' shown in the illustration is four to one and all taps are evenly spaced. If 110 volts were applied to terminals 'X1' and 'X3', what would be indicated across 'H1' and 'H2'? EL-0082 A. 37.5 volts B. 55 volts C. 220 volts D. 440 volts

Last Answer : Answer: C