What is the approximate voltage produced by a nickel-cadmium battery cell? A. 1.25 volts B. 1.50 volts C. 2.20 volts D. 6.05 volts

What is the approximate voltage produced by a nickel-cadmium battery cell? A. 1.25 volts B. 1.50 volts C. 2.20 volts D. 6.05 volts
by

1 Answer

Answer :

Answer: A
by

Related questions

What is the approximate voltage per cell produced by the nickel-iron (Edison) battery? A. 0.85 volts B. 1.35 volts C. 2.20 volts D. 6.05 volts

Description : What is the approximate voltage per cell produced by the nickel-iron (Edison) battery? A. 0.85 volts B. 1.35 volts C. 2.20 volts D. 6.05 volts

Last Answer : Answer: B

The plates of a NiCad storage battery are made of ________. A. potassium hydroxide with a small amount of sulfuric acid B. lead and lead peroxide C. silver oxide and lead sulfate D. combinations of nickel powder and nickel & cadmium salts

Description : The plates of a NiCad storage battery are made of ________. A. potassium hydroxide with a small amount of sulfuric acid B. lead and lead peroxide C. silver oxide and lead sulfate D. combinations of nickel powder and nickel & cadmium salts

Last Answer : Answer: D

To determine the state of charge of a nickel-cadmium battery, you would use a/an _____________. A. voltmeter B. hydrometer C. ammeter D. potentiometer

Description : To determine the state of charge of a nickel-cadmium battery, you would use a/an _____________. A. voltmeter B. hydrometer C. ammeter D. potentiometer

Last Answer : Answer: A

To determine the state of charge of a nickel-cadmium battery, you should ___________. A. check the electrolyte with a hydrometer B. use the constant specific gravity method C. use a nonbreakable mercury thermometer D. connect a voltmeter to the battery terminals

Description : To determine the state of charge of a nickel-cadmium battery, you should ___________. A. check the electrolyte with a hydrometer B. use the constant specific gravity method C. use a nonbreakable mercury thermometer D. connect a voltmeter to the battery terminals

Last Answer : Answer: D

When charging a nickel-cadmium battery, ____________. A. the charging rate should be lessened when gassing commences B. overcharging should be avoided C. the specific gravity of the electrolyte will be unaffected by the state of charge D. add distilled water just prior to charging to insure proper mixing

Description : When charging a nickel-cadmium battery, ____________. A. the charging rate should be lessened when gassing commences B. overcharging should be avoided C. the specific gravity of the electrolyte will be ... by the state of charge D. add distilled water just prior to charging to insure proper mixing

Last Answer : Answer: C

To test the state of charge of a nickel-cadmium battery, you should use a/an ____________. A. ammeter B. voltmeter C. hydrometer D. potentiometer

Description : To test the state of charge of a nickel-cadmium battery, you should use a/an ____________. A. ammeter B. voltmeter C. hydrometer D. potentiometer

Last Answer : Answer: B

A nickel-cadmium battery is receiving a normal charge and gases freely. The charging current should _____________. A. be increased B. be decreased C. be cut off and the battery allowed to cool D. remain the same

Description : A nickel-cadmium battery is receiving a normal charge and gases freely. The charging current should _____________. A. be increased B. be decreased C. be cut off and the battery allowed to cool D. remain the same

Last Answer : Answer: D

Local action in a nickel-cadmium battery is offset by _____________. A. separating the positive and negative plates with plastic spacers B. separating the positive and negative plates with resin impregnated spacers C. adding a small amount of lithium hydroxide to the electrolyte D. trickle charging

Description : Local action in a nickel-cadmium battery is offset by _____________. A. separating the positive and negative plates with plastic spacers B. separating the positive and negative plates with resin impregnated spacers C. adding a small amount of lithium hydroxide to the electrolyte D. trickle charging

Last Answer : Answer: D

Which of the following statements concerning nickel-cadmium batteries is true? A. When mixing electrolyte always add acid to the water. B. Nickel-cadmium batteries can be charged and discharged only a limited number of times without damage to the cells. C. Nickel-cadmium batteries can be stored for a long time and still keep a full charge without additional charging. D. The electrolyte of an idle nickel-cadmium battery must be replaced monthly to maintain battery condition.

Description : Which of the following statements concerning nickel-cadmium batteries is true? A. When mixing electrolyte always add acid to the water. B. Nickel-cadmium batteries can be charged and ... The electrolyte of an idle nickel-cadmium battery must be replaced monthly to maintain battery condition.

Last Answer : Answer: C

The electrolyte used in a nickel-cadmium battery is distilled water and ______________. A. diluted sulfuric acid B. potassium hydroxide C. lead sulfate D. zinc oxide

Description : The electrolyte used in a nickel-cadmium battery is distilled water and ______________. A. diluted sulfuric acid B. potassium hydroxide C. lead sulfate D. zinc oxide

Last Answer : Answer: B

What are the disadvantages of nickel cadmium battery?

Description : What are the disadvantages of nickel cadmium battery? 

Last Answer : Status of charge not known Number of cells are more Cost very high Environmental protection agency considers cadmium as a hazardous material, difficult to discard at the end of life. 

In the illustrated circuit, what is the voltage of the battery if the resistance of R1 is 150 ohms, the total resistance is 250 ohms and the current though R2 is 25 milliamps? EL-0036 A. 12 volts B. 24 volts C. 1.5 volts D. 6.25 volts

Description : In the illustrated circuit, what is the voltage of the battery if the resistance of R1 is 150 ohms, the total resistance is 250 ohms and the current though R2 is 25 milliamps? EL-0036 A. 12 volts B. 24 volts C. 1.5 volts D. 6.25 volts

Last Answer : Answer: D

At high discharge rates, nickel-cadmium storage batteries are superior to lead-acid batteries because they __________. A. require fewer cells for the same voltage and less mounting space B. are able to produce higher voltages and do not have to be charged as often C. can be charged and discharged many times without much damage D. have no individual cells to replace at the end of useful life

Description : At high discharge rates, nickel-cadmium storage batteries are superior to lead-acid batteries because they __________. A. require fewer cells for the same voltage and less mounting space B. are able to ... times without much damage D. have no individual cells to replace at the end of useful life

Last Answer : Answer: C

When the circuit shown in the illustration is operating correctly, the voltage at the reference electrode will be kept in the optimum range of ____________. EL-0090 A. 0.01 - 0.05 volt B. 0.80 - 0.85 volt C. 35 - 60 volts D. 100 - 115 volts

Description : When the circuit shown in the illustration is operating correctly, the voltage at the reference electrode will be kept in the optimum range of ____________. EL-0090 A. 0.01 - 0.05 volt B. 0.80 - 0.85 volt C. 35 - 60 volts D. 100 - 115 volts

Last Answer : Answer: B

What is the calculated voltage at the positive and negative terminals of the battery shown in the illustration if each cell has a voltage of 1.5 volts? EL-0034 A. 1.5 volts B. 3.0 volts C. 6.0 volts D. 12.0 volts

Description : What is the calculated voltage at the positive and negative terminals of the battery shown in the illustration if each cell has a voltage of 1.5 volts? EL-0034 A. 1.5 volts B. 3.0 volts C. 6.0 volts D. 12.0 volts

Last Answer : Answer: A

The distance between a generator and its load is 100 feet. What would be the approximate total voltage drop across a two wire supply cable if the current were 5.5 amperes and the resistance of the wire were 2.525 ohms per 1,000 feet? A. 0.5 volts B. 1.38 volts C. 1.90 volts D. 2.77 volts

Description : The distance between a generator and its load is 100 feet. What would be the approximate total voltage drop across a two wire supply cable if the current were 5.5 amperes and the resistance of the wire were 2.525 ohms per 1,000 feet? A. 0.5 volts B. 1.38 volts C. 1.90 volts D. 2.77 volts

Last Answer : Answer: D

The power supplied to a motor is six kilowatts at 120 volts. What is the impedance of the motor? A. 0.05 Ohms B. 0.50 Ohms C. 2.40 Ohms D. 24.00 Ohms

Description : The power supplied to a motor is six kilowatts at 120 volts. What is the impedance of the motor? A. 0.05 Ohms B. 0.50 Ohms C. 2.40 Ohms D. 24.00 Ohms

Last Answer : Answer: C

A balanced three-phase, 50 Hz voltage is applied to a 3 phase, 4 pole, induction motor. When the motor is delivering rated output, the slip is found to be 0.05. The speed of the rotor m.m.f. relative to the rotor structure is (A) 1500 r.p.m. (B) 1425 r.p.m. (C) 25 r.p.m. (D) 75 r.p.m.

Description : A balanced three-phase, 50 Hz voltage is applied to a 3 phase, 4 pole, induction motor. When the motor is delivering rated output, the slip is found to be 0.05. The speed of the rotor m.m.f. relative to the rotor structure is (A) 1500 r.p.m. (B) 1425 r.p.m. (C) 25 r.p.m. (D) 75 r.p.m.

Last Answer : (D) 75 r.p.m.

In the illustrated circuit the voltage is 12 VDC and the resistance is 3 ohms. If the battery is rated for 120 amp-hours, how long before the voltage will drop to 1.75 volts per cell? EL-0018 A. 12 hours B. 1.75 days C. 30 hours D. 2.5 days

Description : In the illustrated circuit the voltage is 12 VDC and the resistance is 3 ohms. If the battery is rated for 120 amp-hours, how long before the voltage will drop to 1.75 volts per cell? EL-0018 A. 12 hours B. 1.75 days C. 30 hours D. 2.5 days

Last Answer : Answer: C

The open-circuit voltage of a fully charged lead-acid battery cell is _____________. A. 1.5 volts B. 1.8 volts C. 2.0 volts D. 2.3 volts

Description : The open-circuit voltage of a fully charged lead-acid battery cell is _____________. A. 1.5 volts B. 1.8 volts C. 2.0 volts D. 2.3 volts

Last Answer : Answer: C

A battery is connected to a circuit containing three resistors in parallel. The values of the three resistors are 2 ohms, 3 ohms, and 6 ohms. What is the voltage of the battery if the total circuit current is 12 amps? A. 2 volts B. 6 volts C. 12 volts D. 24 volt

Description : A battery is connected to a circuit containing three resistors in parallel. The values of the three resistors are 2 ohms, 3 ohms, and 6 ohms. What is the voltage of the battery if the total circuit current is 12 amps? A. 2 volts B. 6 volts C. 12 volts D. 24 volt

Last Answer : Answer: C

The storage battery generally used in electric power station is A. Nickel-cadmium battery B. Zinc carbon battery C. Lead-acid battery D. None of the above

Description : The storage battery generally used in electric power station is A. Nickel-cadmium battery B. Zinc carbon battery C. Lead-acid battery D. None of the above

Last Answer : C. Lead-acid battery

The storage battery generally used in electric power station is A] nickel-cadmium battery B] zinc-carbon battery C] lead-acid battery D] None of the above

Description : The storage battery generally used in electric power station is A] nickel-cadmium battery B] zinc-carbon battery C] lead-acid battery D] None of the above

Last Answer : C] lead-acid battery

Nickel-cadmium storage batteries are superior to lead-acid batteries because they __________. A. put out higher voltages and require no maintenance B. can remain idle and keep a full charge for a long time C. need fewer cells in series and use less mounting space D. all of the above

Description : Nickel-cadmium storage batteries are superior to lead-acid batteries because they __________. A. put out higher voltages and require no maintenance B. can remain idle and keep a full charge for a long time C. need fewer cells in series and use less mounting space D. all of the above

Last Answer : Answer: B

Common nickel-cadmium and nickel-iron storage batteries utilize _______________. A. acid primary cells B. alkaline primary cells C. acid secondary cells D. alkaline secondary cells

Description : Common nickel-cadmium and nickel-iron storage batteries utilize _______________. A. acid primary cells B. alkaline primary cells C. acid secondary cells D. alkaline secondary cells

Last Answer : Answer: D

Nickel-cadmium batteries are superior to lead-acid batteries at high discharge rates because they _______________. A. deliver a large amount of power and can be recharged in a shorter time B. need fewer cells in connected series and less mounting space C. have higher output voltages and require no maintenance D. all of the above

Description : Nickel-cadmium batteries are superior to lead-acid batteries at high discharge rates because they _______________. A. deliver a large amount of power and can be recharged in a shorter time B. need ... less mounting space C. have higher output voltages and require no maintenance D. all of the above

Last Answer : Answer: A

A 400/200 volts transformer has pu impedance of 0.05. The HV side voltage required to circulate full load...

Description : A 400/200 volts transformer has pu impedance of 0.05. The HV side voltage required to circulate full load current during short circuit test is

Last Answer : A 400/200 volts transformer has pu impedance of 0.05. The HV side voltage required to circulate full load current during short circuit test is 20 V

In the illustrated circuit, what is the voltage measured across R1 if the battery is 24 volts, the resistance of R1 is 34 ohms, and the resistance of R2 is 126 ohms? EL-0036 A. 24 volts B. 18.9 volts C. 5.1 volts D. 150 millivolts

Description : In the illustrated circuit, what is the voltage measured across R1 if the battery is 24 volts, the resistance of R1 is 34 ohms, and the resistance of R2 is 126 ohms? EL-0036 A. 24 volts B. 18.9 volts C. 5.1 volts D. 150 millivolts

Last Answer : Answer: C

Using the graph in figure 3-7, what is the approximate value of current when the voltage is 12.5 volts?

Description : Using the graph in figure 3-7, what is the approximate value of current when the voltage is 12.5 volts?

Last Answer : 1.25 amperes.

Voltage can be stepped up from 6 to approximately a) 10,000 volts b) 15.00 0 volts c) 20,000 volts d) 25,000 volts

Description : Voltage can be stepped up from 6 to approximately a) 10,000 volts b) 15.00 0 volts c) 20,000 volts d) 25,000 volts

Last Answer : c) 20,000 volts

When charging a 100 amp-hour lead-acid battery, ___________. A. the temperature of the electrolyte should not be allowed to exceed 90°F B. the charging rate should be no greater than 125% of the battery amp-hour rating C. the source of power for charging should be 2.5 volts per cell D. gassing within the battery decreases when nearing full charge and it will be necessary to reduce the charging current to a low finishing rate

Description : When charging a 100 amp-hour lead-acid battery, ___________. A. the temperature of the electrolyte should not be allowed to exceed 90°F B. the charging rate should be no greater than 125% of the ... nearing full charge and it will be necessary to reduce the charging current to a low finishing rate

Last Answer : Answer: C

A common-emitter circuit has an input voltage of 0.1 volt, an output voltage of 2.0 volts, an input current of 0.5 milliamps, and an output current of 10 milliamps. What is the power gain? A. 20 B. 40 C. 400 D. 4000

Description : A common-emitter circuit has an input voltage of 0.1 volt, an output voltage of 2.0 volts, an input current of 0.5 milliamps, and an output current of 10 milliamps. What is the power gain? A. 20 B. 40 C. 400 D. 4000

Last Answer : Answer: C

What would be the voltage drop across the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts

Description : What would be the voltage drop across the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts

Last Answer : Answer: C

What would be the voltage drop across the parallel branches of the circuit shown in the illustration if the source is 30 volts the resistance for R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts

Description : What would be the voltage drop across the parallel branches of the circuit shown in the illustration if the source is 30 volts the resistance for R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts

Last Answer : Answer: B

If a 6 volt battery were connected in series with a 24 volt battery by putting their negative terminals together, what would be the result? A. 'Zero' volts B. 12 volts of the opposite polarity C. 18 volts, positive on the 24 volt battery D. 30 volts, negative on the 24 volt battery

Description : If a 6 volt battery were connected in series with a 24 volt battery by putting their negative terminals together, what would be the result? A. 'Zero' volts B. 12 volts of the opposite polarity C. 18 volts, positive on the 24 volt battery D. 30 volts, negative on the 24 volt battery

Last Answer : Answer: C

The dielectric strength of a vacuum or dry air is approximately ________________. A. 450 volts/inch B. 1000 volts/inch C. 20-kv/inch D. 50-kv/inch

Description : The dielectric strength of a vacuum or dry air is approximately ________________. A. 450 volts/inch B. 1000 volts/inch C. 20-kv/inch D. 50-kv/inch

Last Answer : Answer: C

When a nickel-cadium battery begins gassing while connected to the battery charging circuit, you should _____________. A. do nothing as this is a normal condition when charging B. add distilled water to each cell to reduce the specific gravity of the electrolyte C. add potassium hydroxide to each cell to increase the specific gravity of the electrolyte D. decrease the charging rate

Description : When a nickel-cadium battery begins gassing while connected to the battery charging circuit, you should _____________. A. do nothing as this is a normal condition when charging B. add distilled water ... to each cell to increase the specific gravity of the electrolyte D. decrease the charging rate

Last Answer : Answer: A

What will be the total output voltage if four 1.5 volt batteries are connected in a series-parallel arrangement as shown in the illustration? EL-0039 A. 1.5 volts B. 3.0 volts C. 4.5 volts D. 6.0 volts

Description : What will be the total output voltage if four 1.5 volt batteries are connected in a series-parallel arrangement as shown in the illustration? EL-0039 A. 1.5 volts B. 3.0 volts C. 4.5 volts D. 6.0 volts

Last Answer : Answer: B

In the illustration, 12 volts is applied to the circuit where the resistance of R1 is 10 ohms and R2 is 10 ohms. what is the voltage across R2? EL-0036 A. 1.2 volts B. 2 volts C. 6 volts D. 12 volts

Description : In the illustration, 12 volts is applied to the circuit where the resistance of R1 is 10 ohms and R2 is 10 ohms. what is the voltage across R2? EL-0036 A. 1.2 volts B. 2 volts C. 6 volts D. 12 volts

Last Answer : Answer: C

In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 1 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal ... 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: A

In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

What is the voltage across 'R3' of the illustrated circuit if the supply is 24 volts and the resistance of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms? EL-0020 A. 2 volts B. 6 volts C. 8 volts D. 10 volts

Description : What is the voltage across 'R3' of the illustrated circuit if the supply is 24 volts and the resistance of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms? EL-0020 A. 2 volts B. 6 volts C. 8 volts D. 10 volts

Last Answer : Answer: D

What is the voltage across 'R2' of the illustrated circuit if the supply is 24 volts and the resistance of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms? EL-0020 A. 2 volts B. 6 volts C. 8 volts D. 10 volts

Description : What is the voltage across 'R2' of the illustrated circuit if the supply is 24 volts and the resistance of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms? EL-0020 A. 2 volts B. 6 volts C. 8 volts D. 10 volts

Last Answer : Answer: C

What is the voltage across 'R1' of the illustrated circuit if the supply is 24 volts and resistance of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms? EL-0020 A. 2 volts B. 6 volts C. 8 volts D. 10 volts

Description : What is the voltage across 'R1' of the illustrated circuit if the supply is 24 volts and resistance of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms? EL-0020 A. 2 volts B. 6 volts C. 8 volts D. 10 volts

Last Answer : Answer: B

Can I replace Nickel Cadmium batteries with NiMH?

Description : Can I replace Nickel Cadmium batteries with NiMH?

Last Answer : Yah, that’s fine. Just don’t put your NiMH batteries in the NiCad charger.

Whic of the following pairs of materials serves as electrodes in chargeable batteries commonly used in devices such as torch lights, electric shavers, etc.? (1) Iron and cadmium (2) Nickel and cadmium (3) Lead peroxide and lead (4) Zinc and carbon

Description : Whic of the following pairs of materials serves as electrodes in chargeable batteries commonly used in devices such as torch lights, electric shavers, etc.? (1) Iron and cadmium (2) Nickel and cadmium (3) Lead peroxide and lead (4) Zinc and carbon

Last Answer : (2) Nickel and cadmium Explanation: A rechargeable battery, storage battery, or accumulator is a type of electrical battery. It comprises one or more electrochemical cells, and is a ... sizes, ranging from button cells to megawatt systems connected to stabilize an electrical distribution network.

Compare between lead acid and nickel-cadmium batteries?

Description : Compare between lead acid and nickel-cadmium batteries?

Last Answer : Lead acid : Dilute H2SO4, spongy and PbSO2, low efficiency, 2 volt per cell, less strong, requires more maintenance, less efficient wrt temperature, discharges fast, low cost, problem of sulfation.

Which of the following pairs of materials serves as electrodes in chargeable batteries commonly used in devices such as torch lights, electric shavers, etc. ? (1) Iron and cadmium (2) Nickel and cadmium (3) Lead peroxide and lead (4) Zinc and carbon

Description : Which of the following pairs of materials serves as electrodes in chargeable batteries commonly used in devices such as torch lights, electric shavers, etc. ? (1) Iron and cadmium (2) Nickel and cadmium (3) Lead peroxide and lead (4) Zinc and carbon

Last Answer : Nickel and cadmium

A tube has a transconductance of 800 mhos and a load resistor of 50 kohms. When control grid voltage varies by 6 volts, the plate voltage will vary by what amount?

Description : A tube has a transconductance of 800 mhos and a load resistor of 50 kohms. When control grid voltage varies by 6 volts, the plate voltage will vary by what amount?

Last Answer : 240 volts.