Before servicing the device indicated as 'A' in panels #1 and #3 of the illustration, the device labeled 'CT' must __________. EL-0003 A. have the disconnected leads taped to prevent short circuiting. B. only be connected to multimeter on the ammeter setting C. be short circuited D. have one lead grounded to discharge static electricity for the prevention of damage to electronic components

Question

Before servicing the device indicated as 'A' in panels #1 and #3 of the illustration, the device labeled 'CT' must __________. EL-0003 A. have the disconnected leads taped to prevent short circuiting. B. only be connected to multimeter on the ammeter setting C. be short circuited D. have one lead grounded to discharge static electricity for the prevention of damage to electronic components

asked Jan 4, 2022 by anonymous

1 Answer

Answer :

Answer: C

answered Jan 4, 2022 by anonymous

Related questions

In the illustration, if one of the devices labeled 'TURB' should fail the ___________. EL-0003 A. device labeled 'EXC' will drive the alternator B. device labeled 'BKR' for that alternator should automatically open because of the reverse power relay C. operator must open all the devices labeled 'BKRS' to reduce the load on the remaining turbo-alternator D. emergency generator should automatically start and be placed on line to supply emergency load centers

Description : In the illustration, if one of the devices labeled 'TURB' should fail the ___________. EL-0003 A. device labeled 'EXC' will drive the alternator B. device labeled 'BKR' for that ... -alternator D. emergency generator should automatically start and be placed on line to supply emergency load centers

Last Answer : Answer: B

In the illustration, the component labeled 'EXC' is _______. EL-0003 A. a separate class II regulated DC generator for critical direct current loads B. a generator feeding the FLD winding through the voltage regulator. C. the controller to drive the governor for turbogenerator speed. D. the electronic driver for the switchboard metering circuits

Description : In the illustration, the component labeled 'EXC' is _______. EL-0003 A. a separate class II regulated DC generator for critical direct current loads B. a generator feeding the FLD ... to drive the governor for turbogenerator speed. D. the electronic driver for the switchboard metering circuits

Last Answer : Answer: B

The device labeled 'REG SW' in the illustration is used to ___________. EL-0003 A. shift from the automatic voltage regulator to the manual voltage regulator B. shift the governor control from manual to automatic/zero droop C. enable the operator to read the field voltage on device 'REG ADJ' or device 'MAN ADJ' D. supply regulated control power to the switchboard

Description : The device labeled 'REG SW' in the illustration is used to ___________. EL-0003 A. shift from the automatic voltage regulator to the manual voltage regulator B. shift the governor control from manual to ... device 'REG ADJ' or device 'MAN ADJ' D. supply regulated control power to the switchboard

Last Answer : Answer: A

A switchboard ammeter indicates a reading slightly above 'zero' when the leads are disconnected, this is caused by _____________. A. mechanical misalignment of the meter pointer B. a poor ground for the meter case C. static electricity in the air D. capacitors inside the meter storing charges

Description : A switchboard ammeter indicates a reading slightly above 'zero' when the leads are disconnected, this is caused by _____________. A. mechanical misalignment of the meter pointer B. a poor ground for the meter case C. static electricity in the air D. capacitors inside the meter storing charges

Last Answer : Answer: A

An ammeter reads slightly above 'zero' when its leads are disconnected, this is a result of ___________. A. mechanical misalignment of the meter pointer B. a poor ground for the meter case C. static electricity in the air D. resistors inside the meter storing charges

Description : An ammeter reads slightly above 'zero' when its leads are disconnected, this is a result of ___________. A. mechanical misalignment of the meter pointer B. a poor ground for the meter case C. static electricity in the air D. resistors inside the meter storing charges

Last Answer : Answer: A

When reassembling the equipment shown in the illustration, _____________. El-0001 A. item 2A and 2B should not be installed on assembly #2 until assembly #3 or #4 have been secured to assembly #1 B. item 2A and 2B should be installed on assembly #2 regardless of when assembly #3 has been secured in place C. assembly #2 should be aligned into it's position in assembly #1 before assembly #3 or #4 have been positioned on assembly #1 D. item 5 should be secured to assembly #1 to provide support to assembly #2 during the reassembling of the entire unit

Description : When reassembling the equipment shown in the illustration, _____________. El-0001 A. item 2A and 2B should not be installed on assembly #2 until assembly #3 or #4 have been secured to assembly ... be secured to assembly #1 to provide support to assembly #2 during the reassembling of the entire unit

Last Answer : Answer: B

Vessel pitch can be controlled by either the 'bridge or engine room thrust lever' shown in the illustration; but only with one engine on the line whether in 'cruise or maneuver' mode. The cause is most likely a faulty relay _____________. EL-0095 A. #1 B. #2 C. #3 D. #4

Description : Vessel pitch can be controlled by either the 'bridge or engine room thrust lever' shown in the illustration; but only with one engine on the line whether in 'cruise or maneuver' mode. The cause is most likely a faulty relay _____________. EL-0095 A. #1 B. #2 C. #3 D. #4

Last Answer : Answer: D

In replacing a defective transformer with a new one, which of the following actions must be carried out to insure proper operation of the equipment it serves? A. The secondary leads must be grounded for 10 minutes to remove static charges. B. The transformer connections must be made as before with regard to the indicated polarity. C. The iron core of the transformer must be flashed to pre-magnetize it. D. The iron core must be grounded for 10 minutes to remove any residual magnetism.

Description : In replacing a defective transformer with a new one, which of the following actions must be carried out to insure proper operation of the equipment it serves? A. The secondary leads must be grounded ... magnetize it. D. The iron core must be grounded for 10 minutes to remove any residual magnetism.

Last Answer : Answer: B

As shown in the illustration, the function of the switch labeled 'PFSW' is to determine the ______________. EL-0003 A. bus frequency B. reactive volt amperes of the bus C. frequency of either generator D. power factor of either generator

Description : As shown in the illustration, the function of the switch labeled 'PFSW' is to determine the ______________. EL-0003 A. bus frequency B. reactive volt amperes of the bus C. frequency of either generator D. power factor of either generator

Last Answer : Answer: D

The devices labeled 'L' in the illustration are _________. EL-0003 A. load lights indicating that the generator breaker is closed and the generator is supplying power to the main bus B. synchronizing lights. When the synchroscope is at the 12 o'clock position the lights are on at their brightest indicating that the generators are in phase C. emergency lighting for the switchboard to enable the meters to be read in case of power failure D. synchronizing lights. When the synchroscope is at the 12 o'clock position the lights are at their dimmest or out indicating the the generators are in phase

Description : The devices labeled 'L' in the illustration are _________. EL-0003 A. load lights indicating that the generator breaker is closed and the generator is supplying power to the main bus B. ... o'clock position the lights are at their dimmest or out indicating the the generators are in phase

Last Answer : Answer: D

When troubleshooting electronic equipment, you should use a high impedance multimeter ________________. A. to prevent excess current flow through the meter that would damage it B. for AC measurements only and a low resistance meter for DC measurements C. whenever a low impedance meter is not available, regardless of the components being tested D. so as not to load down the circuit and obtain erroneous voltage readings

Description : When troubleshooting electronic equipment, you should use a high impedance multimeter ________________. A. to prevent excess current flow through the meter that would damage it B. for AC measurements only ... being tested D. so as not to load down the circuit and obtain erroneous voltage readings

Last Answer : Answer: D

In the illustrated 450 VAC system, what should be provided between the bus and the device labeled 'F'? EL-0003 A. a potential transformer B. a current transformer C. an emergency disconnect device D. an audible alarm and indicating light

Description : In the illustrated 450 VAC system, what should be provided between the bus and the device labeled 'F'? EL-0003 A. a potential transformer B. a current transformer C. an emergency disconnect device D. an audible alarm and indicating light

Last Answer : Answer: A

As shown in the illustration, the circuit has been on the line for several days when component 'E1' burns out. The operator receives an alarm, switches over 'B' to energize the standby component 'E2' and tells the electrician to renew 'E1'. The opera EL-0058 A. burned out rapidly due to an overused and overheated connection terminal which in turn led to 'C' burning out B. installation developed an accidental connection to 'D' and short-circuited the main line resulting in overloaded fuses just after the master switch C. is a 110 volt DC device being used in a 115 volt AC circuit and will conduct only on the positive half-cycle D. is of a lower wattage rating than required for the circuit therefore limiting the current through the alarm relay which will not pick up

Description : As shown in the illustration, the circuit has been on the line for several days when component 'E1' burns out. The operator receives an alarm, switches over 'B' to energize the standby ... than required for the circuit therefore limiting the current through the alarm relay which will not pick up

Last Answer : Answer: D

As shown in the illustration, when the 'speed control' system is in 'SPLIT' _______________. EL-0096 A. Relays #1, #5 and #8 are not used B. the 'slew rated controller' is grounded through Relay #6 C. the RPM 'function generator' and 'thrust levers' have no control D. the 'E/P converters' are bypassed and air is fed directly to the governors via the 'load sharing valve'

Description : As shown in the illustration, when the 'speed control' system is in 'SPLIT' _______________. EL-0096 A. Relays #1, #5 and #8 are not used B. the 'slew rated controller' is grounded through Relay ... E/P converters' are bypassed and air is fed directly to the governors via the 'load sharing valve'

Last Answer : Answer: C

In the illustration, the tan and white wires are connected to the solenoid valve. The solinoid valve is_________. EL-0043 A. in the liquid line before the TXV B. energized and open whenever the unit is plugged in C. not grounded so the unit must be modified before using aboard ship D. the water inlet for the ice maker

Description : In the illustration, the tan and white wires are connected to the solenoid valve. The solinoid valve is_________. EL-0043 A. in the liquid line before the TXV B. energized and open whenever the unit ... so the unit must be modified before using aboard ship D. the water inlet for the ice maker

Last Answer : Answer: D

In the illustration, the tan and white wires are connected to the solenoid valve. The solenoid valve is_________. EL-0042 A. in the liquid line before the TXV B. energized and open whenever the unit is plugged in C. not grounded so the unit must be modified before using aboard ship D. the water inlet for the ice maker

Description : In the illustration, the tan and white wires are connected to the solenoid valve. The solenoid valve is_________. EL-0042 A. in the liquid line before the TXV B. energized and open whenever the unit ... so the unit must be modified before using aboard ship D. the water inlet for the ice maker

Last Answer : Answer: D

The illustrated test is being conducted on the motor shown in the illustration, if the lamp lights dimly then ________. EL-0027 A. the bulb needs to be changed to one with a higher wattage rating B. safety procedures need to be reviewed because the test presents a severe electrical shock hazard to the person conducting the test and anyone touching the motor frame C. the disconnected wires are touching, they need to be seperated and the test conducted again D. a ground or partial ground is indicated, a check with a megger should confirm the lamp test

Description : The illustrated test is being conducted on the motor shown in the illustration, if the lamp lights dimly then ________. EL-0027 A. the bulb needs to be changed to one with a higher wattage rating B. ... D. a ground or partial ground is indicated, a check with a megger should confirm the lamp test

Last Answer : Answer: D

What is the direction of current through the load resistor in the circuit shown in the illustration? EL-0085 A. Always from point 'Z' to the grounded end. B. Always from the grounded end to point 'Z'. C. It depends on the instantaneous polarity at point 'W'. D. It cannot be determined without a directional ammeter.

Description : What is the direction of current through the load resistor in the circuit shown in the illustration? EL-0085 A. Always from point 'Z' to the grounded end. B. Always from the grounded end to ... on the instantaneous polarity at point 'W'. D. It cannot be determined without a directional ammeter.

Last Answer : Answer: B

When reading AC current with the multimeter shown in the illustration and you are unsure of the range, the range switch should be set to ___________. EL-0047 A. 10 MA/ 10 AMP with leads in the (-10 A) and (+10 A) jacks B. 10 MA/ 10 AMP with leads in the (-COMMON) and (+) jacks C. 10 MA/ 10 AMP with leads in the (-COMMON) and (+10 A) jacks D. unable to measure AC current with this multimeter

Description : When reading AC current with the multimeter shown in the illustration and you are unsure of the range, the range switch should be set to ___________. EL-0047 A. 10 MA/ 10 AMP with leads in the (-10 A ... leads in the (-COMMON) and (+10 A) jacks D. unable to measure AC current with this multimeter

Last Answer : Answer: D

A faulty 'function generator' shown in the illustration may prevent _____________. EL-0095 A. proper pitch control from both the 'bridge' and 'engine room thrust levers' B. the 'split potentiometer's' ability to control pitch C. the pitch meter from indicating accurately D. relays #2 and/or #3 from energizing

Description : A faulty 'function generator' shown in the illustration may prevent _____________. EL-0095 A. proper pitch control from both the 'bridge' and 'engine room thrust levers' B. the 'split potentiometer ... control pitch C. the pitch meter from indicating accurately D. relays #2 and/or #3 from energizing

Last Answer : Answer: A

You are performing an out-of-circuit test on the semi-conductor shown in the illustration. Using an ohmmeter on 'low power' setting and with leads properly inserted, which of the listed results would indicate a good Emitter-Base junction? EL-0068 A. A low reading with red lead on 'A' and black lead on 'C'; and a high reading with the leads reversed. B. A low reading with red lead on 'A' and black lead on 'B'; and a high reading with the leads reversed. C. A low reading with black lead on'A' and red lead on 'B'; and a high reading with the leads reversed. D. A low reading with black lead on 'A' and red lead on 'C'; and a high reading with the leads reversed.

Description : You are performing an out-of-circuit test on the semi-conductor shown in the illustration. Using an ohmmeter on 'low power' setting and with leads properly inserted, which of the listed results would indicate a good ... lead on 'A' and red lead on 'C'; and a high reading with the leads reversed.

Last Answer : Answer: D

If the illustrated device is fully discharged, what will be the result? EL-0061 A. The battery will be short circuited because the mud space will be filled with lead sulfate B. The electrolyte will be maximum sulfuric acid minimum water C. The electrolyte will be maximum water minimum sulfuric acid. D. The plates will be maximum lead oxide and sponge lead minimum lead sulfate.

Description : If the illustrated device is fully discharged, what will be the result? EL-0061 A. The battery will be short circuited because the mud space will be filled with lead sulfate B. The electrolyte ... minimum sulfuric acid. D. The plates will be maximum lead oxide and sponge lead minimum lead sulfate.

Last Answer : Answer: C

The turns ratio of device 'B' shown in the illustration is two to one (total). If 220 volts were applied to terminals 'H1' & 'H2', what would be indicated across 'X1' & 'X4' with 'X2' & 'X3' connected and isolated? EL-0082 A. 55 volts B. 110 volts C. 220 volts D. 440 volts

Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 220 volts were applied to terminals 'H1' & 'H2', what would be indicated across 'X1' & 'X4' with 'X2' & 'X3' connected and isolated? EL-0082 A. 55 volts B. 110 volts C. 220 volts D. 440 volts

Last Answer : Answer: B

The turns ratio of device 'B' shown in the illustration is two to one (total). If 440 volts were applied to terminals 'H1' & 'H2', what would be indicated across 'X1' & 'X4' with 'X2' & 'X3' connected and isolated? EL-0082 A. 110 volts B. 220 volts C. 880 volts D. 1760 volts

Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 440 volts were applied to terminals 'H1' & 'H2', what would be indicated across 'X1' & 'X4' with 'X2' & 'X3' connected and isolated? EL-0082 A. 110 volts B. 220 volts C. 880 volts D. 1760 volts

Last Answer : Answer: B

When using a multimeter for resistance measurements, it should be calibrated by clipping the loose ends of the leads together and _____________. A. setting the instrument pointer at 'zero' ohms B. adjusting the line voltage to calibrate the instrument C. plugging each end of one test lead into the plus and minus terminals D. using a special purpose resistance measuring instrument (a bridge)

Description : When using a multimeter for resistance measurements, it should be calibrated by clipping the loose ends of the leads together and _____________. A. setting the instrument pointer at 'zero' ohms B. ... the plus and minus terminals D. using a special purpose resistance measuring instrument (a bridge)

Last Answer : Answer: A

If fuse #1 shown in the illustration is defective, a voltage tester connected across points 'C' and 'B' will ____________. EL-0062 A. show a reading of 55 volts B. show full line voltage across the fuse C. give positive indication that fuse #2 is good D. give positive indication that fuse #1 is defective

Description : If fuse #1 shown in the illustration is defective, a voltage tester connected across points 'C' and 'B' will ____________. EL-0062 A. show a reading of 55 volts B. show full line voltage ... C. give positive indication that fuse #2 is good D. give positive indication that fuse #1 is defective

Last Answer : Answer: D

In the illustration, the chemical reaction depicted indicates that the _________. EL-0061 A. battery is being charged at a high rate B. cell is short circuited C. cell is discharging D. battery is attached to a trickle charger

Description : In the illustration, the chemical reaction depicted indicates that the _________. EL-0061 A. battery is being charged at a high rate B. cell is short circuited C. cell is discharging D. battery is attached to a trickle charger

Last Answer : Answer: C

What operational characteristics do the components labeled as 'S' and 'R' represent in the motor controller diagram shown in the illustration? EL-0080 A. Standard and Reverse directions B. Stop and Restart features C. Subnormal and Regular loading D. Start and Run functions

Description : What operational characteristics do the components labeled as 'S' and 'R' represent in the motor controller diagram shown in the illustration? EL-0080 A. Standard and Reverse directions B. Stop and Restart features C. Subnormal and Regular loading D. Start and Run functions

Last Answer : Answer: D

An electrical appliance is earthed to 1. Protect the appliance against any damage 2. Prevent electric shocks 3. Avoid short-circuiting Which of the above is/are correct? (a) 1 only (b) 2 only (c) 1 and 2 (d) 2 and 3

Description : An electrical appliance is earthed to 1. Protect the appliance against any damage 2. Prevent electric shocks 3. Avoid short-circuiting Which of the above is/are correct? (a) 1 only (b) 2 only (c) 1 and 2 (d) 2 and 3

Last Answer : Ans:(b)

In the illustration, the component labeled 'G' _________. EL-0031 A. is lined with cardboard to maintain a moisture (electrolyte) barrier between cells B. is a one piece container with compartments for each individual cell C. must be UL approved for shipboard use D. can only contain one cell

Description : In the illustration, the component labeled 'G' _________. EL-0031 A. is lined with cardboard to maintain a moisture (electrolyte) barrier between cells B. is a one piece container with compartments for each individual cell C. must be UL approved for shipboard use D. can only contain one cell

Last Answer : Answer: B

If your multimeter gives a reading in ohms when testing each end of each conductor of a three-conductor cable, this indicates ______________. A. continuity of the conductor B. an infinite resistance C. the presence of a partial ground D. that the conductor is not short circuited

Description : If your multimeter gives a reading in ohms when testing each end of each conductor of a three-conductor cable, this indicates ______________. A. continuity of the conductor B. an infinite resistance C. the presence of a partial ground D. that the conductor is not short circuited

Last Answer : Answer: A

While troubleshooting a circuit in an engine room central control console, a resistor is suspected of being faulty. Which of the following precautions must be observed if an ohmmeter is to be used to check its value? A. Correct polarity must be observed because reverse bias will damage the component. B. Meter leads must not be twisted so as to cancel out the individual magnetic fields. C. Resistor's circuit must be de-energized and at least one end of the component isolated. D. The meter case must be grounded prior to attaching the leads.

Description : While troubleshooting a circuit in an engine room central control console, a resistor is suspected of being faulty. Which of the following precautions must be observed if an ohmmeter is to be used to ... of the component isolated. D. The meter case must be grounded prior to attaching the leads.

Last Answer : Answer: C

In actual applications, electrical connections to 'R1-R2' of figure 'A' and to 'R1-R2- R3' of figure 'B' shown in the illustration are made by ______________. EL-0092 A. soldered contacts B. spliced and taped connections C. slip rings and brushes D. solderless crimp-on connectors

Description : In actual applications, electrical connections to 'R1-R2' of figure 'A' and to 'R1-R2- R3' of figure 'B' shown in the illustration are made by ______________. EL-0092 A. soldered contacts B. spliced and taped connections C. slip rings and brushes D. solderless crimp-on connectors

Last Answer : Answer: C

Which of the devices listed is indicated by the electronic symbol lettered as 'A', shown in the illustration? EL-0016 A. Thyristor B. Diode C. Capacitor D. Transistor

Description : Which of the devices listed is indicated by the electronic symbol lettered as 'A', shown in the illustration? EL-0016 A. Thyristor B. Diode C. Capacitor D. Transistor

Last Answer : Answer: B

A CT has 2 – secondary windings. If we use only one secondary winding can we keep the unused secondary winding short circuited?

Description : A CT has 2 – secondary windings. If we use only one secondary winding can we keep the unused secondary winding short circuited?

Last Answer : No. If it is short-circuited then the ratio will not get correctly. The turns of primary winding will be shared between 2 secondary windings. So the unused secondary winding should kept open.

Which plant parameters shown in the illustration would produce an alarm if they exceeded preset values? EL-0094 A. SME #7 CYL. EXH. and L.O. TO RDCN. GR. B. L.O. PRESS. TO MN. ENG. and PME #3 MN. BRG. C. L.O. PRESS. TO MN. ENG. and L.O. TO RDCN. GR. D. PME #3 MN. BRG. and SME #7 CYL. EXH.

Description : Which plant parameters shown in the illustration would produce an alarm if they exceeded preset values? EL-0094 A. SME #7 CYL. EXH. and L.O. TO RDCN. GR. B. L.O. PRESS. TO MN. ENG. and PME #3 MN. BRG. C. L.O. PRESS. TO MN. ENG. and L.O. TO RDCN. GR. D. PME #3 MN. BRG. and SME #7 CYL. EXH.

Last Answer : Answer: D

Which plant parameters shown in the illustration would produce an alarm if they fell below preset values? EL-0094 A. SME #7 CYL. EXH. and L.O. PRESS. TO RDCN. GR. B. L.O. PRESS TO MN. ENG. and PME #3 MN. BRG. C. L.O. PRESS. TO MN. ENG and L.O. PRESS. TO RDCN. GR. D. PME #3 MN. BRG. and SME #7 CYL. EXH.

Description : Which plant parameters shown in the illustration would produce an alarm if they fell below preset values? EL-0094 A. SME #7 CYL. EXH. and L.O. PRESS. TO RDCN. GR. B. L.O. PRESS TO MN. ENG. and PME #3 MN. BRG. C. ... . TO MN. ENG and L.O. PRESS. TO RDCN. GR. D. PME #3 MN. BRG. and SME #7 CYL. EXH.

Last Answer : Answer: C

The purpose of the capacitor within component 'B' of the circuit shown in the illustration is to ____________. EL-0081 A. prolong the life of the component's contacts B. discharge the neon within the envelope C. counteract the inductive reactance in the circuit D. store power to operate the circuit should 'D' open

Description : The purpose of the capacitor within component 'B' of the circuit shown in the illustration is to ____________. EL-0081 A. prolong the life of the component's contacts B. discharge the neon within ... the inductive reactance in the circuit D. store power to operate the circuit should 'D' open

Last Answer : Answer: A

The turns ratio of device 'B' shown in the illustration is two to one (total). If 110 volts were applied to terminals 'X1,3' and 'X2,4', what would be indicated across 'H1' and 'H2'? EL-0082 A. 27.5 volts B. 55 volts C. 220 volts D. 440 volts

Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 110 volts were applied to terminals 'X1,3' and 'X2,4', what would be indicated across 'H1' and 'H2'? EL-0082 A. 27.5 volts B. 55 volts C. 220 volts D. 440 volts

Last Answer : Answer: D

The turns ratio of device 'B' shown in the illustration is two to one (total). If 220 volts were applied to terminals 'H1' and 'H2', what would be indicated across 'X3' and 'X4'? EL-0082 A. 55 volts B. 110 volts C. 440 volts D. 880 volts

Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 220 volts were applied to terminals 'H1' and 'H2', what would be indicated across 'X3' and 'X4'? EL-0082 A. 55 volts B. 110 volts C. 440 volts D. 880 volts

Last Answer : Answer: A

The turns ratio of device 'B' shown in the illustration is two to one (total). If 440 volts were applied to terminals 'H1' and 'H2', what would be indicated across 'X1,3' and 'X2,4'? EL-0082 A. 55 volts B. 110 volts C. 220 volts D. 880 volts

Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 440 volts were applied to terminals 'H1' and 'H2', what would be indicated across 'X1,3' and 'X2,4'? EL-0082 A. 55 volts B. 110 volts C. 220 volts D. 880 volts

Last Answer : Answer: B

The turns ratio of device 'A' shown in the illustration is four to one and all taps are evenly spaced. If 110 volts were applied to terminals 'X1' and 'X3', what would be indicated across 'H1' and 'H2'? EL-0082 A. 37.5 volts B. 55 volts C. 220 volts D. 440 volts

Description : The turns ratio of device 'A' shown in the illustration is four to one and all taps are evenly spaced. If 110 volts were applied to terminals 'X1' and 'X3', what would be indicated across 'H1' and 'H2'? EL-0082 A. 37.5 volts B. 55 volts C. 220 volts D. 440 volts

Last Answer : Answer: C

The turns ratio of device 'A' shown in the illustration is four to one and all the taps are equally spaced. If 120 volts were applied between 'X1' and 'X2', what would be indicated across 'H1' and 'H4'? EL-0082 A. 30 volts B. 120 volts C. 480 volts D. 1440 volts

Description : The turns ratio of device 'A' shown in the illustration is four to one and all the taps are equally spaced. If 120 volts were applied between 'X1' and 'X2', what would be indicated across 'H1' and 'H4'? EL-0082 A. 30 volts B. 120 volts C. 480 volts D. 1440 volts

Last Answer : Answer: D

Before testing insulation with a megohmmeter, the windings of large machines should be grounded for about 15 minutes just prior to the test as the ______________. A. insulation may be damaged B. insulation may be covered with moisture C. armature windings will have a greater number of leakage paths D. larger machines may acquire a charge of static electricity during operation

Description : Before testing insulation with a megohmmeter, the windings of large machines should be grounded for about 15 minutes just prior to the test as the ______________. A. insulation may be damaged ... number of leakage paths D. larger machines may acquire a charge of static electricity during operation

Last Answer : Answer: D

What is the resistance value indicated on the multimeter scale illustrated, if the range switch is set at R X 100, and the needle is at the position indicated by the letter 'R'? EL-0047 A. 6.0 ohms B. 162.5 ohms C. 600 ohms D. 16,250 ohms

Description : What is the resistance value indicated on the multimeter scale illustrated, if the range switch is set at R X 100, and the needle is at the position indicated by the letter 'R'? EL-0047 A. 6.0 ohms B. 162.5 ohms C. 600 ohms D. 16,250 ohms

Last Answer : Answer: C

What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 100, and the needle is at the position indicated by the letter 'Y'? EL-0047 A. 220 ohms B. 240 ohms C. 2,400 ohms D. 24,000 ohms

Description : What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 100, and the needle is at the position indicated by the letter 'Y'? EL-0047 A. 220 ohms B. 240 ohms C. 2,400 ohms D. 24,000 ohms

Last Answer : Answer: C

What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 1, and the needle is at the position indicated by the letter 'A'? EL-0047 A. 10 ohms B. 100 ohms C. 200 ohms D. 1,000 ohms

Description : What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 1, and the needle is at the position indicated by the letter 'A'? EL-0047 A. 10 ohms B. 100 ohms C. 200 ohms D. 1,000 ohms

Last Answer : Answer: C

What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 1, and the needle is at the position indicated by the letter 'F'? EL-0047 A. 0.6 ohms B. 6 ohms C. 9.6 ohms D. .38 ohms

Description : What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 1, and the needle is at the position indicated by the letter 'F'? EL-0047 A. 0.6 ohms B. 6 ohms C. 9.6 ohms D. .38 ohms

Last Answer : Answer: A

What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 1, and the needle is at the position indicated by the letter 'D'? EL-0047 A. 7.8 ohms B. 8 ohms C. 3.6 ohms D. .36 ohms

Description : What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 1, and the needle is at the position indicated by the letter 'D'? EL-0047 A. 7.8 ohms B. 8 ohms C. 3.6 ohms D. .36 ohms

Last Answer : Answer: C

What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 1, and the needle is at the position indicated by the letter 'R'? EL-0047 A. 6 ohms B. 6.8 ohms C. 1.7 ohms D. 167 ohms

Description : What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 1, and the needle is at the position indicated by the letter 'R'? EL-0047 A. 6 ohms B. 6.8 ohms C. 1.7 ohms D. 167 ohms

Last Answer : Answer: A

Please log in or register to add a comment.

Please log in or register to answer this question.

1 Answer

Answer :

Please log in or register to add a comment.

Related questions