Description : A disadvantage of using the configuration in the illustrated circuit is _________. EL-0045 A. no current gain B. high input resistance C. high voltage gain D. becomes unstable with an increase of ambient temperature
Last Answer : Answer: A
Description : In the illustrated circuit, the amplifier is connected in what basic configuration? EL-0045 A. common emitter B. common collector C. darlington paired, capacitor coupled D. common base
Last Answer : Answer: D
Description : In the illustrated amplifier, the RESET potentiometer A1R2 sets the stability of the control loop by changing the reset time constant. As the potentiometer is turned clockwise _________. EL-0060 A. ... is increased to the summing point at terminal 5 D. response time is increased decreasing stability
Last Answer : Answer: B
Description : In the illustrated circuit, if the input to leads 'B' and 'Y' was 24 VDC the output between 'A' and 'X' will be _________. EL-0069 A. 24 VDC B. 22.8 VDC, 24 VDC minus the 1.2 VDC voltage drop across two diodes C. undeterminable without knowing the turns ratio of the transformer D. 0 VDC
Description : In the illustrated circuit, what is the phase relationship of the amplifier output compared to the input? EL-0022 A. 0° in-phase B. 180° out of phase C. phase angle of the input divided by power factor D. unable to determine without the value of the bias voltage
Description : If the electricity represented by the wave form in 'B' were applied to the left side of the illustrated circuit, the output on the right side would be ____________. EL-0064 A. direct current with the ... lower lead D. clipped to a value equal to the square root of 3 times the input voltage value
Last Answer : Answer: C
Description : In the illustrated circuit, if the battery is 24 VDC, the resistance of R1 is 24 ohms, and the resistance of R2 is 24 ohms, the total current is _________. EL-0019 A. 2 amps B. 1 amp C. 1/2 amp D. 2.4 amps
Description : In the illustrated motor controller circuit, which statment is true? EL-0023 A. The high and low speed lights operate at less than line voltage with a resistor in series. B. This controller can be ... . The wattage of the high speed light must be greater than the wattage of the low speed light.
Description : The 'function generator' of the control circuit illustrated _______________. EL-0095 A. can be programmed to produce a non-linear output for a linear input depending on operating conditions B. is used for ... which or how many engines are needed for a required vessel speed D. all of the above
Description : Basic operating characteristics of the operational amplifier such as gain and stability are the function of its _____________. A. differential input stage B. power output stage C. feedback circuit D. supply voltages
Description : In the illustrated three phase alternator, line voltage is _________. EL-0074 A. 1.73 times the phase voltage B. equal to the phase voltage C. phase voltage divided by 1.73 D. unable to answer this question without knowing the line current
Description : In the illustrated device, the part labeled '1A' _________. EL-0001 A. are start and run windings for a single phase shaded pole induction motor B. is the stator for a polyphase induction ... armature for a squirrel cage rotor motor D. are direct current shunt field windings for a universal motor
Description : If reading AC current with the illustrated device and unsure of the range as a precaution , the first step should be to _________. EL-0047 A. secure power and test for voltage B. disconnect the ... resistance and use Ohm's law to calculate current D. unable to safely measure current with the device
Description : In the illustrated circuit, the amplifier is connected in what basic configuration? EL-0022 A. common base B. reverse bias, negative feedback C. common emitter D. common collector
Description : Component F in the illustrated device is for _________. EL-0033 A. short circut protection B. latching the trip unit closed after resetting the breaker C. overload protection D. providing a flexible connection between the input terminal G and the tripping unit E
Description : The device in figure 'B' shown in the illustration can be used to control an AC load yet maintain its high gain by ______________. EL-0091 A. connecting the load to the output side of the ... connecting the load to the input side of the bridge D. reversing the current flow through the bias winding
Description : Which of the following statements is true regarding the illustrated circuit? El-0069 A. This full wave bridge should never be used aboard ship because the ground on lead 'A' will show on ... be direct current suitable for electronic circuits requiring voltage regulation. D. All the above are true.
Description : If If the input signals are 180 degrees out of phase with each other and a combined output is taken between the two output terminals, what will the amplitude of the combined output signal be?
Last Answer : 200 millivolts.
Description : If the input signals are 180 degrees out of phase with each other, what will be the peak-to-peak amplitude of the output signals?
Last Answer : Each output signal will be 100 millivolts.
Description : If the two input signals to a difference amplifier are equal in amplitude but neither in phase nor 180 degrees out of phase, what will the output signal be?
Last Answer : . A different shape than the input signals but larger in amplitude.
Description : If the two input signals to a difference amplifier are equal in amplitude and 180 degrees out of phase, what will the output signal be?
Last Answer : Equal in shape and frequency to each input signal and larger in amplitude by two times than
Description : When a voltage of 132 VDC is applied to the illustrated circuit with a resistance of 237 ohms the current will be ________. EL-0018 A. 1.236 amps B. 2.048 amps C. 0.557 amps D. 4.200 amps
Description : When a voltage of 132 VDC is applied to the illustrated circuit with a resistance of 470 ohms the current will be ________. EL-0018 A. 0.280 amps B. 3.560 amps C. 602 milliamps D. 1.673 amps
Description : When a voltage of 132 VDC is applied to the illustrated circuit with a resistance of 10,230 ohms the current will be ________. EL-0018 A. 0.012 amps B. 77.5 milliamps C. 10,362 amps D. 0.792 amps
Description : When a voltage of 132 VDC is applied to the illustrated circuit with a resistance of 110 ohms the current will be ________. EL-0018 A. 0.833 amps B. 1.2 amps C. 2.2 amps D. 242 milliamps
Description : When a voltage of 132 VDC is applied to the illustrated circuit with a resistance of 32 ohms the current will be ________. EL-0018 A. 0.242 amps B. 4.125 amps C. 7.757 amps D. 1.64 amps
Description : If a voltage of 132 VDC is applied to the illustrated circuit where the resistance is 12 ohms, then current will be ___________. EL-0018 A. 0.090 amps B. 1.090 amps C. 11 amps D. 144 milliamps
Description : When a voltage of 124 VDC is applied to the illustrated circuit with a resistance of 17.8 ohms the current will be ________. EL-0018 A. 0.143 amps B. 2.555 amps C. 6.966 amps D. 141.8 milliamps
Description : When a voltage of 124 VDC is applied to the illustrated circuit with a resistance of 237 ohms the current will be ________. EL-0018 A. 1.523 amps B. 1.911 amps C. 361 milliamps D. 523.2 milliamps
Description : When a voltage of 124 VDC is applied to the illustrated circuit with a resistance of 470 ohms the current will be________. EL-0018 A. 0.263 amps B. 3.79 amps C. 594 milliamps D. 1.7814 amps
Description : When a voltage of 124 VDC is applied to the illustrated circuit with a resistance of 10,230 ohms the current will be________. EL-0018 A. 0.012 amps B. 82.50 amps C. 10.354 amps D. 0.8439 amps
Description : When a voltage of 124 VDC is applied to the illustrated circuit with a resistance of 110 ohms the current will be________. EL-0018 A. 0.887 amps B. 1.127 amps C. 234 m amps D. 2.13 amps
Description : When a voltage of 124 VDC is applied to the illustrated circuit with a resistance of 32 ohms the current will be ________. EL-0018 A. 0.258 amps B. 3.875 amps C. 8.258 amps D. 156 amps
Description : When a voltage of 124 VDC is applied to the illustrated circuit with a resistance of 12 ohms. the current will be ________. EL-0018 A. 0.096 amps B. 1.16 amps C. 10.33 amps D. 136 m amps
Description : When a voltage of 112 VDC is applied to the circuit illustrated with a resistance of 17.8 ohms the current will be________. EL-0018 A. .158 amps B. 5.82 amps C. 6.29 amps D. 129.8m amps
Description : When a voltage of 112 VDC is applied to the illustrated circuit with a resistance of 237 ohms the current will be ________. EL-0018 A. 1.47 amps B. 2.11 amps C. 347 milliamps D. 472.6 milliamps
Description : When a voltage of 112 VDC is applied to the circuit illustrated with a resistance of 470 ohms the current will be________. EL-0018 A. .238 amps B. 4.196 amps C. 582 m amps D. 19.723 amps
Description : When a voltage of 112 VDC is applied to the circuit illustrated with a resistance of 10,230 ohms the current will be________. EL-0018 A. .010 amps B. .913 amps C. 103 m amps D. 934 m amps
Description : When a voltage of 112 VDC is applied to the circuit illustrated with a resistance of 110 ohms the current will be________. EL-0018 A. .982 amps B. 1.018 amps C. 2.018 amps D. .222 amps
Description : When a voltage of 112 VDC is applied to the illustrated circuit with a resistance of 32 ohms the current will be________. EL-0018 A. .285 amps B. 3.5 amps C. 9.142 amps D. 144 m amps
Description : When a voltage of 112 VDC is applied to the illustrated circuit with a resistance of 12 ohms the current will be ________. EL-0018 A. .107 amps B. 1.28 amps C. 9.33 amps D. 124 milliamps
Description : When a voltage of 110 VDC is applied to the illustrated circuit with a resistance of 17.8 ohms the current will be________. EL-0018 A. 2.88 amps B. 6.18 amps C. 127.8m amps D. 161 amps
Description : When a voltage of 110 VDC is applied to the illustrated circuit with a resistance of 237 ohms the current will be________. EL-0018 A. .464 amps B. 1.464 amps C. 2.154 amps D. 3.47 amps
Description : When a voltage of 110 VDC is applied to the illustrated circuit with a resistance of 470 ohms the current will be ________. EL-0018 A. .234 amps B. 4.272 amps C. 580 amps D. 2,008 amps
Description : When a voltage of 110 VDC is applied to the circuit illustrated with a resistance of 10,230 ohms the current will be________. EL-0018 A. 0.0107 amps B. 93 amps C. 10,340 amps D. .951 amps
Description : When a voltage of 110 VDC is applied to the illustrated circuit with a resistance of 110 ohms the current will be________. EL-0018 A. .2 amps B. .1 amps C. 1 amps D. 220m amps
Description : When a voltage of 110 VDC is applied to the circuit illustrated with a resistance of 32 ohms the current will be________. EL-0018 A. .29 amps B. 3.44 amps C. 9.31 amps D. 142 amps
Description : When a voltage of 110 VDC is applied to the circuit illustrated with a resistance of 12 ohms the current will be________. EL-0018 A. .11 amps B. 1.31 amps C. 9.17 amps D. 122m amps
Description : When a voltage of 95 VDC is applied to the circuit illustrated with a resistance of 237 ohms the current will be________. EL-0018 A. 1.40 amps B. 2.49 amps C. 332 milliamps D. 400.8 milliamps
Description : When a voltage of 95 VDC is applied to the circuit illustrated with a resistance of 470 ohms the current will be _______. EL-0018 A. 4.95 amps B. 202.2 milliamps C. 565.00 milliamps D. 2,325 milliamps