Which of the following statements is true regarding the illustrated circuit? El-0069 A. This full wave bridge should never be used aboard ship because the ground on lead 'A' will show on the ship's ground detection system. B. Lead 'X' will always be positive (+) with respect to ground. C. This bridge circuit output will be direct current suitable for electronic circuits requiring voltage regulation. D. All the above are true.

Question

Which of the following statements is true regarding the illustrated circuit? El-0069 A. This full wave bridge should never be used aboard ship because the ground on lead 'A' will show on the ship's ground detection system. B. Lead 'X' will always be positive (+) with respect to ground. C. This bridge circuit output will be direct current suitable for electronic circuits requiring voltage regulation. D. All the above are true.

asked Jan 4, 2022 by anonymous

1 Answer

Answer :

Answer: B

answered Jan 4, 2022 by anonymous

Related questions

If the electricity represented by the wave form in 'B' were applied to the left side of the illustrated circuit, the output on the right side would be ____________. EL-0064 A. direct current with the top lead positive with repect to the lower lead B. direct current, half wave rectified with a ripple frequency of 60 hz C. direct current with the top lead negative with repect to the lower lead D. clipped to a value equal to the square root of 3 times the input voltage value

Description : If the electricity represented by the wave form in 'B' were applied to the left side of the illustrated circuit, the output on the right side would be ____________. EL-0064 A. direct current with the ... lower lead D. clipped to a value equal to the square root of 3 times the input voltage value

Last Answer : Answer: C

In the illustrated circuit, if the input to leads 'B' and 'Y' was 24 VDC the output between 'A' and 'X' will be _________. EL-0069 A. 24 VDC B. 22.8 VDC, 24 VDC minus the 1.2 VDC voltage drop across two diodes C. undeterminable without knowing the turns ratio of the transformer D. 0 VDC

Description : In the illustrated circuit, if the input to leads 'B' and 'Y' was 24 VDC the output between 'A' and 'X' will be _________. EL-0069 A. 24 VDC B. 22.8 VDC, 24 VDC minus the 1.2 VDC voltage drop across two diodes C. undeterminable without knowing the turns ratio of the transformer D. 0 VDC

Last Answer : Answer: D

The illustrated device is a _______. EL-0064 A. full wave bridge rectifier B. half wave bridge rectifier C. solid state voltage regulator D. direct current (DC) filter

Description : The illustrated device is a _______. EL-0064 A. full wave bridge rectifier B. half wave bridge rectifier C. solid state voltage regulator D. direct current (DC) filter

Last Answer : Answer: A

The schematic diagram shown in the illustration represents which of the listed solid-state circuits? EL-0069 A. Bridge rectifier B. Magnetic amplifier C. Flip-flop generator D. Cathodic amplifier

Description : The schematic diagram shown in the illustration represents which of the listed solid-state circuits? EL-0069 A. Bridge rectifier B. Magnetic amplifier C. Flip-flop generator D. Cathodic amplifier

Last Answer : Answer: A

Which of the following statements is true about the illustrated circuit? EL-0030 A. The field rheostat is used for manual voltage control. B. if the generator is flat compounded then the field rheostat needs to be adjusted up at full load to compensate for excessive voltage droop. C. this is a direct current elevator control with the lower and raise corresponding with the direction that the elevator will travel. D. the motor will tend to act like a series motor and overspeed with the controller in the full raise position.

Description : Which of the following statements is true about the illustrated circuit? EL-0030 A. The field rheostat is used for manual voltage control. B. if the generator is flat compounded then the field rheostat ... to act like a series motor and overspeed with the controller in the full raise position.

Last Answer : Answer: A

In the illustrated motor controller circuit, which statment is true? EL-0023 A. The high and low speed lights operate at less than line voltage with a resistor in series. B. This controller can be converted for use with a three phase motor by connecting the L3 lead to the LS contact attached to the overload relay. C. The lights must be rated at a wattage equal or greater that the motor output wattage. D. The wattage of the high speed light must be greater than the wattage of the low speed light.

Description : In the illustrated motor controller circuit, which statment is true? EL-0023 A. The high and low speed lights operate at less than line voltage with a resistor in series. B. This controller can be ... . The wattage of the high speed light must be greater than the wattage of the low speed light.

Last Answer : Answer: A

In electronic circuits, DC voltages can be positive (+) or negative (-) when measured with respect to the _________. A. printed circuit board 'common' trace B. chassis, console frame or hull 'ground' C. analogue or digital circuitry 'common' bus D. all of the above

Description : In electronic circuits, DC voltages can be positive (+) or negative (-) when measured with respect to the _________. A. printed circuit board 'common' trace B. chassis, console frame or hull 'ground' C. analogue or digital circuitry 'common' bus D. all of the above

Last Answer : Answer: D

Federal Regulations (46 CFR) require the circuit in the illustration to _________. EL-0009 A. be at the vessel's ship's service generator distribution switchboard for normal power, normal lighting and emergency lighting systems. B. not have any resulting ground currents flow through hazardous locations on a tank vessel where line to line voltage exceeds 3,000 VAC C. not be used on systems where the resulting ground will interfere with the operation of electronic equipment D. All the above are correct

Description : Federal Regulations (46 CFR) require the circuit in the illustration to _________. EL-0009 A. be at the vessel's ship's service generator distribution switchboard for normal power, normal lighting ... ground will interfere with the operation of electronic equipment D. All the above are correct

Last Answer : Answer: A

The illustrated circuit is a wheatstone bridge. If the meter 'G' reads 0 with the switch closed then ________. EL-0024 A. the current through R1 - R2 is equal to the current through R3 - Rx B. the voltage across b - d is equal to the voltage of E C. the resistance of Rx is equal to the resistance of R2 D. all the above are true

Description : The illustrated circuit is a wheatstone bridge. If the meter 'G' reads 0 with the switch closed then ________. EL-0024 A. the current through R1 - R2 is equal to the current through R3 - Rx B. the voltage ... of E C. the resistance of Rx is equal to the resistance of R2 D. all the above are true

Last Answer : Answer: A

If the illustrated motor fails to start and gives a loud hum when the start button is pushed, the problem is ________. EL-0007 A. one of the phases to the motor is not energized because of an open motor lead B. the 'Disc.sw.' is open C. power to 'L1' at the 'Disc.sw.' is not energized because of a problem with the ship's electrical distribution system D. 'OL1' is open because of 'T1' overload causing the motor to single phase

Description : If the illustrated motor fails to start and gives a loud hum when the start button is pushed, the problem is ________. EL-0007 A. one of the phases to the motor is not energized because of ... electrical distribution system D. 'OL1' is open because of 'T1' overload causing the motor to single phase

Last Answer : Answer: A

In the illustration, the component labeled 'EXC' is _______. EL-0003 A. a separate class II regulated DC generator for critical direct current loads B. a generator feeding the FLD winding through the voltage regulator. C. the controller to drive the governor for turbogenerator speed. D. the electronic driver for the switchboard metering circuits

Description : In the illustration, the component labeled 'EXC' is _______. EL-0003 A. a separate class II regulated DC generator for critical direct current loads B. a generator feeding the FLD ... to drive the governor for turbogenerator speed. D. the electronic driver for the switchboard metering circuits

Last Answer : Answer: B

In which section of the 24 VDC power supply circuit illustrated, does the greatest change in voltage level take place when fed from ships power. EL-0085 A. I B. II C. III D. IV

Description : In which section of the 24 VDC power supply circuit illustrated, does the greatest change in voltage level take place when fed from ships power. EL-0085 A. I B. II C. III D. IV

Last Answer : Answer: A

The 'function generator' of the control circuit illustrated _______________. EL-0095 A. can be programmed to produce a non-linear output for a linear input depending on operating conditions B. is used for controlling relay contacts' positions in selection circuits C. automatically selects which or how many engines are needed for a required vessel speed D. all of the above

Description : The 'function generator' of the control circuit illustrated _______________. EL-0095 A. can be programmed to produce a non-linear output for a linear input depending on operating conditions B. is used for ... which or how many engines are needed for a required vessel speed D. all of the above

Last Answer : Answer: A

Receptacle outlets aboard ship should be designed so those mounted according to 46 CFR 111 have _____________. A. there must be a sufficient number of receptacle outlets in the crew accommodations for an adequate level of habitability B. each receptacle outelt must be compatible with the voltage and current of the circuit in which it is installed C. a receptacle outlet must not have any exposed parts with the plug opening uncovered D. all of the above

Description : Receptacle outlets aboard ship should be designed so those mounted according to 46 CFR 111 have _____________. A. there must be a sufficient number of receptacle outlets in the crew accommodations for an ... outlet must not have any exposed parts with the plug opening uncovered D. all of the above

Last Answer : Answer: D

The circuit illustrated represents a 2 wire DC ground detecting system. If the positive bus is grounded and the test button is pushed, which of the lamps will be brightest? EL-0008 A. X B. Y C. both will be equal brightness. D. both will go out.

Description : The circuit illustrated represents a 2 wire DC ground detecting system. If the positive bus is grounded and the test button is pushed, which of the lamps will be brightest? EL-0008 A. X B. Y C. both will be equal brightness. D. both will go out.

Last Answer : Answer: C

An open shunt field in a direct current machine may be located by connecting the field circuit to an external power source, equal to the rated field voltage or less, and tested with a voltmeter from _____________. A. one line terminal to each coil lead in succession B. one field coil to each adjacent field coil in turn C. any suitable ground to any available line lead D. any field pole to each field coil lead

Description : An open shunt field in a direct current machine may be located by connecting the field circuit to an external power source, equal to the rated field voltage or less, and tested with a voltmeter from ... C. any suitable ground to any available line lead D. any field pole to each field coil lead

Last Answer : Answer: A

An electrical device which employs a stationary armature and a rotating electromagnetic field is used aboard ship as a ____________. A. magnetic amplifier B. ship's service alternator C. three-wire DC generator D. saturable core reactor

Description : An electrical device which employs a stationary armature and a rotating electromagnetic field is used aboard ship as a ____________. A. magnetic amplifier B. ship's service alternator C. three-wire DC generator D. saturable core reactor

Last Answer : Answer: B

In the illustrated ground detection system with a ground on phase A, if the switch is opened __________. EL-0009 A. lamp A will dim or go out depending on the severity of the ground B. all three lamps will return to their normal brightness indicating that the bulbs are not burnt out C. lamps B and C will dim lamp A will be brighter D. lamp A will start flickering if the ground is in an AC induction motor

Description : In the illustrated ground detection system with a ground on phase A, if the switch is opened __________. EL-0009 A. lamp A will dim or go out depending on the severity of the ground B. all three ... lamp A will be brighter D. lamp A will start flickering if the ground is in an AC induction motor

Last Answer : Answer: B

In the illustration circuit, A, B, C, and D are each 12 volts. What is the voltage at the output lead connected to 'A' and 'B' with respect to the output lead connected to 'C' and 'D'? EL-0039 A. (+) 48 volts B. (-) 24 volts C. (-) 48 volts D. (+) 24 volts

Description : In the illustration circuit, A, B, C, and D are each 12 volts. What is the voltage at the output lead connected to 'A' and 'B' with respect to the output lead connected to 'C' and 'D'? EL-0039 A. (+) 48 volts B. (-) 24 volts C. (-) 48 volts D. (+) 24 volts

Last Answer : Answer: B

A temperature instrumentation system for an engine room console consists of a resistance temperature detector (RTD), a measuring bridge circuit, and a meter (or alarm circuit).Which of the following statements is true concerning the measuring bridge circu A. The input voltage varies in a linear fashion with temperature. B. The voltage across the center of the resistance bridge is always constant. C. The resistance bridge is said to be balanced when its output voltage is zero. D. The input voltage of the resistance bridge is the constant temperature signal.

Description : A temperature instrumentation system for an engine room console consists of a resistance temperature detector (RTD), a measuring bridge circuit, and a meter (or alarm circuit).Which of the following ... is zero. D. The input voltage of the resistance bridge is the constant temperature signal.

Last Answer : Answer: C

The speed of a squirrel-cage, multi-speed, induction motor, as used aboard ship, is varied by changing the __________. A. number of connected poles in the stator B. frequency to the motor C. excitation voltage D. resistance of the rotor circuit

Description : The speed of a squirrel-cage, multi-speed, induction motor, as used aboard ship, is varied by changing the __________. A. number of connected poles in the stator B. frequency to the motor C. excitation voltage D. resistance of the rotor circuit

Last Answer : Answer: A

As shown in the illustration, the circuit which 'shapes' the linear output of the thrust lever so that the steady-state ship speed is linear with respect to that lever's setting is the _____________. EL-0095 A. 'pitch controller' B. 'error amplifier' C. 'function generator' D. 'servo amplifier'

Description : As shown in the illustration, the circuit which 'shapes' the linear output of the thrust lever so that the steady-state ship speed is linear with respect to that lever's setting is the _____________. EL-0095 A. 'pitch controller' B. 'error amplifier' C. 'function generator' D. 'servo amplifier'

Last Answer : Answer: C

Wire in general, when used aboard vessels must meet minimum requirements. Which of the following statements is/are correct? A. Each wire must be 14 AWG or larger, regardless of locations and use. B. Wire must be copper stranded. C. The only wire that does not have to be in a suitable enclosure or cover is the ground wire used with portable tools and lights. D. All of the above.

Description : Wire in general, when used aboard vessels must meet minimum requirements. Which of the following statements is/are correct? A. Each wire must be 14 AWG or larger, regardless of locations and use. B. ... enclosure or cover is the ground wire used with portable tools and lights. D. All of the above.

Last Answer : Answer: B

In the illustrated circuit, what is the phase relationship of the amplifier output compared to the input? EL-0022 A. 0° in-phase B. 180° out of phase C. phase angle of the input divided by power factor D. unable to determine without the value of the bias voltage

Description : In the illustrated circuit, what is the phase relationship of the amplifier output compared to the input? EL-0022 A. 0° in-phase B. 180° out of phase C. phase angle of the input divided by power factor D. unable to determine without the value of the bias voltage

Last Answer : Answer: B

In the illustration, the tan and white wires are connected to the solenoid valve. The solinoid valve is_________. EL-0043 A. in the liquid line before the TXV B. energized and open whenever the unit is plugged in C. not grounded so the unit must be modified before using aboard ship D. the water inlet for the ice maker

Description : In the illustration, the tan and white wires are connected to the solenoid valve. The solinoid valve is_________. EL-0043 A. in the liquid line before the TXV B. energized and open whenever the unit ... so the unit must be modified before using aboard ship D. the water inlet for the ice maker

Last Answer : Answer: D

In the illustration, the tan and white wires are connected to the solenoid valve. The solenoid valve is_________. EL-0042 A. in the liquid line before the TXV B. energized and open whenever the unit is plugged in C. not grounded so the unit must be modified before using aboard ship D. the water inlet for the ice maker

Description : In the illustration, the tan and white wires are connected to the solenoid valve. The solenoid valve is_________. EL-0042 A. in the liquid line before the TXV B. energized and open whenever the unit ... so the unit must be modified before using aboard ship D. the water inlet for the ice maker

Last Answer : Answer: D

If the illustrated test is being performed to determine which winding is grounded and the light does not come on then __________. EL-0027 A. winding is grounded and you should continue on to the next winding to see if any others are grounded B. winding is not grounded and you should continue on to the next winding until the light comes on designating that winding as grounded C. test is meaningless because you can not determine if a winding is grounded without a megger. D. ground is not in the windings but probabily in the pecker head, you should check and retape the line lead connections

Description : If the illustrated test is being performed to determine which winding is grounded and the light does not come on then __________. EL-0027 A. winding is grounded and you should continue on to the ... the windings but probabily in the pecker head, you should check and retape the line lead connections

Last Answer : Answer: B

In the illustrated electronic governor, the circuit card connected to the potential and current transformers is for ________. EL-0046 A. increasing the signal strength to the governor to maintain constant engine speed with increased load B. send a kilowatt signal to the metering circuit C. shutting down the prime mover in the event of reverse power to protect from motorization D. conditioning the load through the use of a magnetic amplifier current transformer

Description : In the illustrated electronic governor, the circuit card connected to the potential and current transformers is for ________. EL-0046 A. increasing the signal strength to the governor to ... from motorization D. conditioning the load through the use of a magnetic amplifier current transformer

Last Answer : Answer: A

Which of the following precautions should be taken when troubleshooting various power circuits using a common solenoid-type mechanical voltage tester (wiggins)? A. Never use this tester on circuits greater than 60 Hz, as the coil's resultant high impedance lowers current and magnetic pull. The tester may not register dangerous voltages. B. Always remember that the unit is polarity sensitive and if used on DC circuits reversing the leads may result in high temperatures within the tester. C. Never connect the device to circuits where potentials greater than 120 volts may be present, as the coil's extremely fine wire cannot withstand more than a few amps. D. Always pre-set the meter to the next higher range than the amount of voltage expected in the circuit in order to prevent damage from an

Description : Which of the following precautions should be taken when troubleshooting various power circuits using a common solenoid-type mechanical voltage tester (wiggins)? A. Never use this tester on circuits greater ... voltage expected in the circuit in order to prevent damage from an off-scale reading.

Last Answer : Answer: A

A ground detection system is shown in the illustration for a three-phase ungrounded distribution system. Which of the following statements describes the conditions indicated if a full ground occurs in line 'A'? EL-0009 A. Lamp 'A' will burn brightly and Lamps 'B' and 'C' will go out. B. Lamp 'A' will burn brightly and Lamps 'B' and 'C' will burn dimly but not go out. C. Lamp 'A' will burn brightly and Lamps 'B' and 'C' will burn with normal intensity. D. Lamp 'A' will go out and Lamps 'B' and 'C' will burn brightly.

Description : A ground detection system is shown in the illustration for a three-phase ungrounded distribution system. Which of the following statements describes the conditions indicated if a full ground occurs in line 'A'? EL-0009 A ... . D. Lamp 'A' will go out and Lamps 'B' and 'C' will burn brightly.

Last Answer : Answer: D

If reading AC current with the illustrated device and unsure of the range as a precaution , the first step should be to _________. EL-0047 A. secure power and test for voltage B. disconnect the lead to be tested and connect the meter in series C. connect the meter to measure resistance and use Ohm's law to calculate current D. unable to safely measure current with the device

Description : If reading AC current with the illustrated device and unsure of the range as a precaution , the first step should be to _________. EL-0047 A. secure power and test for voltage B. disconnect the ... resistance and use Ohm's law to calculate current D. unable to safely measure current with the device

Last Answer : Answer: A

Transformers are used onboard ships with AC generators to _____________. A. change frequency B. increase power output to modulating frequency controllers C. decrease power output to modulating frequency controllers D. permit higher voltage for electric motor operation and low voltage for lighting circuits

Description : Transformers are used onboard ships with AC generators to _____________. A. change frequency B. increase power output to modulating frequency controllers C. decrease power output to modulating frequency ... D. permit higher voltage for electric motor operation and low voltage for lighting circuits

Last Answer : Answer: D

The advantage of using the illustrated circuit configuration is _________. EL-0045 A. high input resistance B. high current gain C. the best stability with an increase in temperature D. the input and output are 180 degrees out of phase

Description : The advantage of using the illustrated circuit configuration is _________. EL-0045 A. high input resistance B. high current gain C. the best stability with an increase in temperature D. the input and output are 180 degrees out of phase

Last Answer : Answer: C

The circuit illustrated represents a single phase AC ground detecting system. If a ground occurs on line 'B', which of the lamps will burn the brightest? EL-0008 A. X B. Y C. Both will be equal brightness. D. both will go out.

Description : The circuit illustrated represents a single phase AC ground detecting system. If a ground occurs on line 'B', which of the lamps will burn the brightest? EL-0008 A. X B. Y C. Both will be equal brightness. D. both will go out.

Last Answer : Answer: A

Which of the following statements is/are true regarding requirements for receptacle outlets aboard vessels? A. Each receptacle outlet operating at 100 volts or more must have a grounding pole. B. Outlets connecting a lifeboat and the vessel's electrical system must have threaded plugs. C. Machinery spaces must contain sufficient outlets for lighting all machinery with a portable light having a 50 foot flexible cord. D. All of the above.

Description : Which of the following statements is/are true regarding requirements for receptacle outlets aboard vessels? A. Each receptacle outlet operating at 100 volts or more must have a grounding pole. B. Outlets ... machinery with a portable light having a 50 foot flexible cord. D. All of the above.

Last Answer : Answer: A

The illustrated circuits are used to measure ___________. EL-0024 A. resistance B. gauss or magnetic field strength C. battery discharge rate in Amp-hours D. current

Description : The illustrated circuits are used to measure ___________. EL-0024 A. resistance B. gauss or magnetic field strength C. battery discharge rate in Amp-hours D. current

Last Answer : Answer: A

During start-up of the circuit shown in the illustration, it is noted that the ends of component 'C' alternately glow and become dark without the tube illuminating. The most probable cause for this is that ____________. EL-0081 A. component 'D' is loose and due to the ship's vibrations makes and breaks contact B. the power system's voltage is fluctuating in and out of the range necessary for proper operation C. component 'A' is shorted and therefore unable to produce the high voltage required to start the lamp D. component 'B' contacts are opening and closing thus prohibiting sufficient current flow

Description : During start-up of the circuit shown in the illustration, it is noted that the ends of component 'C' alternately glow and become dark without the tube illuminating. The most probable cause ... start the lamp D. component 'B' contacts are opening and closing thus prohibiting sufficient current flow

Last Answer : Answer: C

The correct term for the illustrated circuit is a ________. EL-0063 A. single phase half wave high power rectifier B. three phase half wave rectifier C. three phase full wave rectifier D. a single phase full wave rectifier

Description : The correct term for the illustrated circuit is a ________. EL-0063 A. single phase half wave high power rectifier B. three phase half wave rectifier C. three phase full wave rectifier D. a single phase full wave rectifier

Last Answer : Answer: C

In the illustrated circuit, section II is considered to be a _______. EL-0085 A. full wave rectifier B. half wave rectifier C. quarter wave rectifier D. short wave rectifier

Description : In the illustrated circuit, section II is considered to be a _______. EL-0085 A. full wave rectifier B. half wave rectifier C. quarter wave rectifier D. short wave rectifier

Last Answer : Answer: A

The ground detection system, shown in the illustration for a low-voltage, threephase system has a ground in line 'A'. Therefore, lamp 'A' will burn ____________. EL-0009 A. dimly or be out, and lamps 'B' and 'C' will burn brightly B. normally, and lamps 'B' and 'C' will burn dimly or be out C. brightly, and lamps 'B' and 'C' will burn dimly or be out D. brightly, and lamps 'B' and 'C' will burn normally

Description : The ground detection system, shown in the illustration for a low-voltage, threephase system has a ground in line 'A'. Therefore, lamp 'A' will burn ____________. EL-0009 A. dimly or be out, and lamps 'B' and ... and 'C' will burn dimly or be out D. brightly, and lamps 'B' and 'C' will burn normally

Last Answer : Answer: A

If reading the AC voltage from the line lead of a 440 VAC controller the range switch illustrated should be set to ___________. EL-0047 A. 1,000 V B. 250 V C. R X 10,000 D. Unable to safely read with this meter.

Description : If reading the AC voltage from the line lead of a 440 VAC controller the range switch illustrated should be set to ___________. EL-0047 A. 1,000 V B. 250 V C. R X 10,000 D. Unable to safely read with this meter.

Last Answer : Answer: A

When a voltage of 132 VDC is applied to the illustrated circuit with a resistance of 237 ohms the current will be ________. EL-0018 A. 1.236 amps B. 2.048 amps C. 0.557 amps D. 4.200 amps

Description : When a voltage of 132 VDC is applied to the illustrated circuit with a resistance of 237 ohms the current will be ________. EL-0018 A. 1.236 amps B. 2.048 amps C. 0.557 amps D. 4.200 amps

Last Answer : Answer: C

When a voltage of 132 VDC is applied to the illustrated circuit with a resistance of 470 ohms the current will be ________. EL-0018 A. 0.280 amps B. 3.560 amps C. 602 milliamps D. 1.673 amps

Description : When a voltage of 132 VDC is applied to the illustrated circuit with a resistance of 470 ohms the current will be ________. EL-0018 A. 0.280 amps B. 3.560 amps C. 602 milliamps D. 1.673 amps

Last Answer : Answer: A

When a voltage of 132 VDC is applied to the illustrated circuit with a resistance of 10,230 ohms the current will be ________. EL-0018 A. 0.012 amps B. 77.5 milliamps C. 10,362 amps D. 0.792 amps

Description : When a voltage of 132 VDC is applied to the illustrated circuit with a resistance of 10,230 ohms the current will be ________. EL-0018 A. 0.012 amps B. 77.5 milliamps C. 10,362 amps D. 0.792 amps

Last Answer : Answer: A

When a voltage of 132 VDC is applied to the illustrated circuit with a resistance of 110 ohms the current will be ________. EL-0018 A. 0.833 amps B. 1.2 amps C. 2.2 amps D. 242 milliamps

Description : When a voltage of 132 VDC is applied to the illustrated circuit with a resistance of 110 ohms the current will be ________. EL-0018 A. 0.833 amps B. 1.2 amps C. 2.2 amps D. 242 milliamps

Last Answer : Answer: B

When a voltage of 132 VDC is applied to the illustrated circuit with a resistance of 32 ohms the current will be ________. EL-0018 A. 0.242 amps B. 4.125 amps C. 7.757 amps D. 1.64 amps

Description : When a voltage of 132 VDC is applied to the illustrated circuit with a resistance of 32 ohms the current will be ________. EL-0018 A. 0.242 amps B. 4.125 amps C. 7.757 amps D. 1.64 amps

Last Answer : Answer: B

If a voltage of 132 VDC is applied to the illustrated circuit where the resistance is 12 ohms, then current will be ___________. EL-0018 A. 0.090 amps B. 1.090 amps C. 11 amps D. 144 milliamps

Description : If a voltage of 132 VDC is applied to the illustrated circuit where the resistance is 12 ohms, then current will be ___________. EL-0018 A. 0.090 amps B. 1.090 amps C. 11 amps D. 144 milliamps

Last Answer : Answer: C

When a voltage of 124 VDC is applied to the illustrated circuit with a resistance of 17.8 ohms the current will be ________. EL-0018 A. 0.143 amps B. 2.555 amps C. 6.966 amps D. 141.8 milliamps

Description : When a voltage of 124 VDC is applied to the illustrated circuit with a resistance of 17.8 ohms the current will be ________. EL-0018 A. 0.143 amps B. 2.555 amps C. 6.966 amps D. 141.8 milliamps

Last Answer : Answer: C

When a voltage of 124 VDC is applied to the illustrated circuit with a resistance of 237 ohms the current will be ________. EL-0018 A. 1.523 amps B. 1.911 amps C. 361 milliamps D. 523.2 milliamps

Description : When a voltage of 124 VDC is applied to the illustrated circuit with a resistance of 237 ohms the current will be ________. EL-0018 A. 1.523 amps B. 1.911 amps C. 361 milliamps D. 523.2 milliamps

Last Answer : Answer: D

When a voltage of 124 VDC is applied to the illustrated circuit with a resistance of 470 ohms the current will be________. EL-0018 A. 0.263 amps B. 3.79 amps C. 594 milliamps D. 1.7814 amps

Description : When a voltage of 124 VDC is applied to the illustrated circuit with a resistance of 470 ohms the current will be________. EL-0018 A. 0.263 amps B. 3.79 amps C. 594 milliamps D. 1.7814 amps

Last Answer : Answer: A

Please log in or register to add a comment.

Please log in or register to answer this question.

1 Answer

Answer :

Please log in or register to add a comment.

Related questions