Inter-distance between ventilation columns in a sewer line is kept A. 25 to 50 m B. 50 m to 100 m C. 100 m to 150 m D. 150 m to 300 m

1 Answer

Answer :

ANS: D

Related questions

Description : Sewer ventilating columns are generally placed at A. Distances 150 m to 300 m B. Upper ends of branch sewers C. Every change in the size of sewers D. All the above

Last Answer : ANS: D

Description : Ventilating shafts are provided to a sewer line at every A. 100 m B. 150 m C. 200 m D. 300 m

Last Answer : ANS: D

Description : For laying a sewer line in a trench of 2 m width, an offset line is marked on the ground parallel to the given centre line at a distance of A. 100 cm B. 120 cm C. 140 cm D. 160 cm

Last Answer : ANS: D

Description : For large sewers, maximum distance between manholes may be A. 50 m B. 100 m C. 200 m D. 300 m

Last Answer : ANS: D

Description : In R.C. sewer pipes, the percentage longitudinal reinforcement to the cross-sectional area of concrete is kept A. 10.0 B. 5.0 C. 2.0 D. 0.25

Last Answer : ANS: D

Description : The minimum diameter of a sewer is kept A. 10 cm B. 15 cm C. 20 cm D. 25 cm

Last Answer : ANS: B

Description : If the diameter of a sewer is 150 mm, the gradient required for generating self cleansing velocity, is A. 1 in 60 B. 1 in 100 C. 1 in 120 D. None of these

Last Answer : ANS: B

Description : The spacing of man holes along a straight portion of a sewer is 300 m, the diameter of the sewer may be A. 0.9 cm B. 1.2 m C. 1.5 m D. > 1.5 m

Last Answer : ANS: D

Description : The reduced levels of the string at the consecutive sight rails A and B are 203.575 m, 203.475 m respectively. If the difference of their R.D.s is 10 m, the gradient of the sewer line is A. 1 in 100 upward B. 1 in 500 upward C. 1 in 100 downward D. 1 in 503 upward

Last Answer : ANS: C

Description : The angle subtended by the surface of sewer water with partial flow, at sewer centre is 120°, the depth of sewerage is A. 20 cm B. 25 cm C. 40 cm D. 50 cm

Last Answer : ANS: D

Description : If the depth of partial flow in a sewer of diameter 2 m, is 50 cm, its wetted perimeter is A. B. /2 C. /3 D. 2 /3

Last Answer : ANS: D

Description : To prevent settling down of sewage both at the bottom and on the sides of a large sewer, self-cleaning velocity recommended for Indian conditions, is A. 0.50 m/sec B. 0.60 m/sec C. 0.70 m/sec D. 0.75 m/sec

Last Answer : ANS: D

Description : At the junction of sewers A. Top of smaller sewer is kept lower B. Top of larger sewer is kept lower C. Tops of both the sewers are at the same level D. None of these

Last Answer : ANS: D

Description : The minimum diameter of sewer to be adopted is A. 10 cm B. 12.5 cm C. 15 cm D. 25 cm

Last Answer : ANS: C

Description : If the depletion of oxygen is found to be 2.5 mg/litre after incubating 2.5 ml of sewage diluted to 250 ml for 5 days at 20°C, B.O.D. of the sewage is A. 50 mg/l B. 100 mg/l C. 150 mg/l D. 250 mg/l

Last Answer : ANS: D

Description : If the depletion of oxygen is found to be 5 ppm after incubating a 2.5% solution of sewage sample for 5 days at 21°C, B.O.D. of the sewage is A. 50 ppm B. 100 ppm C. 150 ppm D. 200 ppm

Last Answer : ANS: D

Description : If the peak discharge of a storm water drain (S.W. Drain) is expected to exceed 150 cumecs, the free board to be provided, is A. 100 cm B. 90 cm C. 80 cm D. 50 cm

Last Answer : ANS: A

Description : If the diameter of a sewer is 100 mm, the gradient required for generating self cleansing velocity is A. 1 in 60 B. 1 in 100 C. 1 in 120 D. None of these

Last Answer : ANS: A

Description : If the diameter of sewer is 225 mm, the gradient required for generating self cleansing velocity, is A. 1 in 60 B. 1 in 100 C. 1 in 120 D. None of these

Last Answer : ANS: C

Description : The width of a rectangular sewer is twice its depth while discharging 1.5 m/sec. The width of the sewer is A. 0.68 m B. 0.88 m C. 1.36 m D. 1.76 m

Last Answer : ANS: C

Description : If is the rugosity coefficient, is the bed slope of sewer, the velocity of flow in m/sec may be obtained by the formula V = (1/n) r2/3 s1/2 evolved by A. Chezy B. Manning C. Bazin D. Kutter

Last Answer : ANS: B

Description : You are asked to design sewer pipes of diameters 0.4 m to 0.9 m at maximum flow, you will assume the sewer flow running at A. Full depth B. Half full C. Two third full D. Three fourth full

Last Answer : ANS: B

Description : For a peak discharge of 0.0157 cumec, with a velocity of 0.9 m/sec, the diameter of the sewer main, is A. 10 cm B. 12 cm C. 15 cm D. 18 cm

Last Answer : ANS: C

Description : For sewer mains of 0.5 to 1 m diameter, the ratio of maximum daily sewage flow to the average daily sewage flow is assumed A. 1.5 B. 2.0 C. 2.5 D. 3.0

Last Answer : ANS: B

Description : Pick up the correct statement from the following: A. The boning rod is used for checking the levels of the sewer inverts B. Manhole covers are made circular for the convenience of the cleaning staff C. A manhole is classified as shallow manhole if its depth is less than 0.9 m D. All the above

Last Answer : ANS: D

Description : A sewer pipe contains 1 mm sand particles of specific gravity 2.65 and 5 mm organic particles of specific gravity 1.2, the minimum velocity required for removing the sewerage, is A. 0.30 m/sec B. 0.35 m/sec C. 0.40 m/sec D. 0.45 m/sec

Last Answer : ANS: D

Description : If the discharge of a sewer running half is 628 1.p.s., i = 0.001, and n = 0.010, the diameter of the sewer, is A. 1.39 m B. 1.49 m C. 1.59 m D. 1.69 m

Last Answer : ANS: D

Description : Pick up the correct statement from the following: A. The sewer pipes of sizes less than 0.4 m diameter are designed as running full at maximum discharge B. The sewer pipes of sizes greater than 0.4 m ... discharge C. The minimum design velocity of sewer pipes is taken as 0.8 m/sec D. All the above

Last Answer : ANS: D

Description : For efficient working of a sewer, it must be ensured that A. Minimum velocity of 0.45 m/sec, is maintained at its minimum flow B. A maximum velocity of 0.90 m/sec, is maintained at its maximum flow C. Both A. and B. D. Neither A. nor B.

Last Answer : ANS: C

Description : The sewage discharge in a detritus tank of a treatment plant is 576 litres/sec with flow velocity of 0.2 m/sec. If the ratio of width to depth is 2, the depth is A. 100 cm B. 110 cm C. 120 cm D. 150 cm

Last Answer : ANS: C

Description : No treatment of the sewage is given if dilution factor is A. Less than 150 B. Between 150 to 200 C. Between 200 to 300 D. More than 500

Last Answer : ANS: D

Description : Drop manholes at the junctions of sewer lines, are provided if A. Invert level of a branch sewer is more than 60 cm that of the main sewer B. Sewer line runs along a main road C. Ordinary manhole cannot be built D. Two sewer lines intersect

Last Answer : ANS: A

Description : The arrangement made for passing the sewer line below an obstruction below the hydraulic gradient lines called A. Inverted syphon B. Depressed sewer C. Sag pipe D. all of these

Last Answer : ANS: D

Description : Antisyphonage pipe is fitted A. At the end of septic tanks B. On manholes C. With a W.C. trap D. At the beginning of sewer line

Last Answer : ANS: C

Description : Hydraulic mean radius is A. Mean radius of sewer B. Difference in heads between two points in circular pipes C. Mean of radii in a pipe line of varying cross -sections D. Cross-sectional area/wetted perimeter

Last Answer : ANS: D

Description : If depth of slab is 10 cm, width of web 30 cm, depth of web 50 cm, centre to centre distance of beams 3 m, effective span of beams 6 m, the effective flange width of the beam, is (A) 200 cm (B) 300 cm (C) 150 cm (D) 100 cm

Last Answer : Answer: Option C

Description : The normal value of over flow rates for plain primary sedimentation tanks, ranges between A. 25,000 to 35,000 litres/sqm/day B. 40,000 to 50,000 litres/sqm/day C. 50,000 to 60,000 litres/sqm/day D. 80,000 to 100,000 litres/sqm/day

Last Answer : ANS: B

Description : The normal values of over flow rates for sedimentation tanks using coagulant, ranges between A. 25,000 to 35,000 litres/sqm/day B. 40,000 to 50,000 litres/sqm/day C. 50,000 to 60,000 litres/sqm/day D. 80,000 to 100,000 litres/sqm/day

Last Answer : ANS: C

Description : For providing an Indian type W.C., the R.C.C. slabs in the toilet portion A. Should be sunk by 20 cm B. Should be kept 20 cm above the adjacent portion C. Should be sunk by 50 cm D. Need not be sunk

Last Answer : ANS: C

Description : Sewer manholes are generally provided at A. The change of gradient B. The change of direction C. The junctions of sewers D. All of these

Last Answer : ANS: D

Description : Aerobic activity is maximum A. In freshly produced sewage B. At sewer pipes C. In sewer treatment plants D. None of these

Last Answer : ANS: A

Description : Sewer pipes need be checked for A. Minimum flow B. Maximum flow C. Both A. and B. D. None of these

Last Answer : ANS: C

Description : The sewer which transports the sewage to the point of treatment, is called A. House sewer B. Out-fall sewer C. Branch sewer D. Main sewer

Last Answer : ANS: B

Description : If a paper moistened with lead acetate for five minutes when placed in manhole turns black. The sewer certainly contains A. Hydrogen sulphide B. Carbon dioxide C. Methane D. Oxygen

Last Answer : ANS: A

Description : If is the diameter of upper circular portion, the area of cross-section of a standard egg shaped sewer, is A. D² B. D² C. D² D. D²

Last Answer : ANS: A

Description : The gradient of sewers depends upon A. Velocity of flow B. Diameter of the sewer C. Discharge D. All the above

Last Answer : ANS: D

Description : The sewer pipe which carries sewage from a building for immediate disposal is A. House sewer B. Lateral sewer C. Intercepting sewer D. Main sewer

Last Answer : ANS: A

Description : Which one of the following tests is used for testing sewer pipes? A. Water test B. Ball test C. Mirror test D. All of these

Last Answer : ANS: D

Description : The sewerage system consists of A. House sewer B. Lateral sewer C. Branch sewer D. All of these

Last Answer : ANS: D

Description : The porosity of sediments in sewer pipes, is usually taken as A. 0.010 B. 0.011 C. 0.012 D. 0.013

Last Answer : ANS: D