Description : The pressure exerted by A. The sewage when running full from inside, is called internal pressure B. The internal pressure if any, causes tensile stress in the pipe material C. Pressure sewers are designed to be safe in tension D. All the above
Last Answer : ANS: D
Description : The underground sewers are more subjected to A. Tensile force B. Compressive force C. Bending force D. Shearing force
Last Answer : ANS: B
Description : For sewers, inverted siphon is provided for A. One pipe B. Two pipes C. Three pipes D. Four pipes
Last Answer : ANS: C
Description : The gradient of sewers depends upon A. Velocity of flow B. Diameter of the sewer C. Discharge D. All the above
Description : For trunk sewers more than 1.25 m in diameter, the ratio of the maximum daily sewage flow to the average daily sewage flow is assumed A. 1.5 B. 2.0 C. 2.5 D. 3.0
Last Answer : ANS: A
Description : The minimum recommended diameter of sewers, is A. 5 cm B. 10 cm C. 15 cm D. 20 cm
Description : The maximum spacing of manholes specified by Indian standard in sewers upto 0.3 m diameter is A. 20 m B. 30 m C. 45 m D. 75 m
Description : The maximum diameter of sewers adopted in the designs is A. 1.0 m B. 2.0 m C. 3.0 m D. 4.0 m
Description : What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2
Last Answer : c. 20.120 N/mm2
Description : The drop man holes are generally provided in sewers for A. Industrial areas B. Large town ships C. Hilly town ships D. Cities in plains
Description : For large sewers, maximum distance between manholes may be A. 50 m B. 100 m C. 200 m D. 300 m
Description : The asbestos cement sewers are A. Light in weight B. Not structurally strong to bear large compressive stress C. Susceptible to corrosion by sulphuric acid D. All the above
Description : The ratio of strength of a hollow shaft to that of a solid shaft subjected to torsion if both are of the same material and of the same outer diameters, the inner diameter of hollow shaft being half of the outer diameter is a. 15/16 b. 16/15 c. 7/8 d. 8/7
Last Answer : a. 15/16
Description : Boussinesq’s equation for ascertaining unit pressure at a depth on sewers due to traffic loads, is A. pt = 3H3p/2 Z5 B. pt = 2H3p/3 Z5 C. pt = 3H3p/2Z5 D. pt = 2 3p/3Z5
Description : In a thick cylindrical shell subjected to an internal pressure (p), the radial stress across the thickness of a cylinder is a) maximum at the outer surface and minimum at the inner surface b) maximum ... and zero at the outer surface d) maximum at the outer surface and zero at the inner surface
Last Answer : c) maximum at the inner surface and zero at the outer surface
Description : If the strain energy stored per unit volume in a hollow shaft subjected to a pure torque when t attains maximum shear stress fs the ratio of inner diameter to outer diameter, is 17/64 (fs/N) (A) 1/2 (B) 1/3 (C) 1/4 (D) 1/5
Last Answer : (C) 1/4
Description : With self cleansing velocity in sewers A. Silting occurs at bottom B. Scouring occurs at bottom C. Both silting and scouring occur at bottom D. Neither silting nor scouring occurs at bottom
Description : In sewers designed with self cleansing velocity, A. The bottom is silted B. The bottom is scoured C. Both silting and scouring occur at the bottom D. Neither silting nor scouring occurs at the bottom
Description : At the junction of sewers A. Top of smaller sewer is kept lower B. Top of larger sewer is kept lower C. Tops of both the sewers are at the same level D. None of these
Description : A metal pipe is 77 cm long. The inner diameter of a cross section is 4 cm, the outer diameter being 4.4cm. -Maths 9th
Last Answer : Let r1 and r2 Inner and outer radii of cylindrical pipe r1 = 4/2 cm = 2 cm r2 = 4.4/2 cm = 2.2 cm Height of cylindrical pipe, h = length of cylindrical pipe = 77 cm (i) curved surface ... CSA of roller = (500 31680) cm2 = 15840000 cm2 = 1584 m2. Therefore, area of playground is 1584 m2. Answer!
Description : Nominal Pipe Size (NPS) of a pipe less than 12 inches in diameter indicates its (A) Inner diameter (B) Outer diameter (C) Thickness (D) Neither inner nor outer diameter
Last Answer : (D) Neither inner nor outer diameter
Description : Nominal size of a pipe is an indication of its __________ diameter. (A) Inner (B) Outer (C) Approximate (D) None of these
Last Answer : (C) Approximate
Description : Sewer manholes are generally provided at A. The change of gradient B. The change of direction C. The junctions of sewers D. All of these
Description : The sewerage system originates from A. House sewers B. Lateral sewers C. Branch sewers D. Main sewers
Description : The gas evolved in sewers is A. Carbondioxide B. Hydrogen sulphide C. Methane D. All of these
Description : The small sewers are cleaned by A. Flushing B. Cane rodding C. Wooden pills D. None of these
Description : In sewers the gas generally found, is A. Hydrogen sulphide (H2S) B. Carbon dioxide (CO2) C. Methane (CH4) D. All the above
Description : In olden days the type of section adopted in trunk and out fall sewers was A. Parabolic shaped B. Horse shoe shaped C. Egg shaped D. Circular shaped
Description : Clogging of sewers, is caused due to A. Silting B. Low discharge C. Greasy and oily matters D. All the above
Description : The laying of sewers is done with A. Magnetic compass B. Theodolite C. Level D. Clinometer
Description : 221 For non-scouring velocity 5 m/sec, the type of sewers generally preferred to, is A. Cast iron sewers B. Cement concrete sewers C. Glazed bricks sewers D. Stone ware sewers
Description : The most efficient cross section of sewers in a separate sewerage system is A. Parabolic B. Circular C. Rectangular D. New egged
Description : The suitable cross-section of sewers to carry combined flow, is A. Circular B. Egg shaped C. Rectangular D. Horse shoe shaped
Description : For trunk and out-fall, the type of sewers generally used, is A. Standard egg shaped B. Circular shaped C. Horse shoe shaped D. Parabolic shaped
Description : In sewers the highest non-scouring velocity is achieved in A. Glazed bricks sewers B. Cast iron sewers C. Cement concrete sewers D. Stone ware sewers
Description : The stone ware sewers A. Are used for carrying sewage and drainage from houses B. Are manufactured from clays and shale C. After casting are dried and burnt at temperature 150°C, 700°C and 1200°C D. All the above
Description : Q No: 191 Design period of 40 to 50 years is adopted for A. Branch sewers B. Main sewers C. Trunk sewers D. All the above
Description : In circular sewers if depth of flow is 0.2 times the full depth, the nominal gradient, A. Is only provided B. Is doubled C. Is trebled D. Is not enough
Description : WASTE WATER ENGINEERING Objective Questions with Answers Q No: 161 The quantity of liquid waste which flows in sewers during the period of rainfall, is known A. Sanitary sewage B. Industrial waste C. Storm sewage D. None of these
Description : In a residential colony, sewers of diameters 100 mm, 150 mm and 225 mm were laid with a gradient 1 in 120. Which portion of the sewage system does not choke in due course of time? A. 100 mm dia. B. 150 mm dia. C. 225 mm dia. D. All of these
Description : The density of population over 40 hectares is 250/hectare. If water supply demand per day is 200 litres and sewage discharge is 80% of water supply, the sewage flow in sewers of separate system, is A. 0.05552 cumec B. 0.05554 cumec C. 0.05556 cumec D. 0.0556 cumec
Description : Pick up the incorrect size of stone ware sewers A. 52.5 cm B. 67.5 cm C. 82.5 cm D. None of these
Description : Setting out the alignments of sewers may start from A. City B. Out-fall C. Tail end D. Any point
Description : Cement concrete sewers are only suitable if non-scouring velocity is between A. 2.5 to 3.0 m/sec B. 3.0 to 4.0 m/sec C. 3.5 to 4.5 m/sec D. 4.5 to 5.5 m/sec
Description : The sewers A. Must be of adequate size to avoid over flow B. Must flow under gravity ½ to ¾ full C. Must be laid at least 2 to 3 m deep to collect /water from the basements D. All the above
Description : For design of sewers, percentage of sewage discharge is assumed A. 65 to 70% B. 70 to 75% C. 75 to 80% D. 85%
Description : Q No: 101 are available in size Stoneware sewers A. 10 cm B. 15 cm C. 20 cm D. All the above
Description : Pick up the in-correct statement from the following: A. Manholes are provided in sewer pipes at suitable intervals B. Catch basins are generally provided in sewers for carrying drainage discharge C. Inlets are generally provided in all sewers D. None of these
Description : The most efficient cross-section of sewers in a combined sewerage system is A. Parabolic B. Circular C. Rectangular D. New egged
Description : Sewer ventilating columns are generally placed at A. Distances 150 m to 300 m B. Upper ends of branch sewers C. Every change in the size of sewers D. All the above