Description : Nominal Pipe Size (NPS) of a pipe less than 12 inches in diameter indicates its (A) Inner diameter (B) Outer diameter (C) Thickness (D) Neither inner nor outer diameter
Last Answer : (D) Neither inner nor outer diameter
Description : A metal pipe is 77 cm long. The inner diameter of a cross section is 4 cm, the outer diameter being 4.4cm. -Maths 9th
Last Answer : Let r1 and r2 Inner and outer radii of cylindrical pipe r1 = 4/2 cm = 2 cm r2 = 4.4/2 cm = 2.2 cm Height of cylindrical pipe, h = length of cylindrical pipe = 77 cm (i) curved surface ... CSA of roller = (500 31680) cm2 = 15840000 cm2 = 1584 m2. Therefore, area of playground is 1584 m2. Answer!
Description : Large diameter sewers subjected to external pressure alone, are reinforced A. Near the inner surface of the pipe B. Near the outer surface of the pipe C. Both A. and B. D. With elliptical cage
Last Answer : ANS: D
Description : The equivalent diameter for the annulus of a double pipe heat exchanger, whose inner pipe has fins on the outside is __________ compared to the same size pipes without fins. (A) More (B) Less (C) Same (D) Unpredictable
Last Answer : (B) Less
Description : Lower BWG means __________ of the tube. (A) Lower thickness (B) Lower cross-section (C) Outer diameter (D) Inner diameter
Last Answer : (B) Lower cross-section
Description : What is the approximate nominal diameter for coarse threads? a. d = 1.136 dc b. d = 1.59 dc c. d = 1.19 dc d. d = 0.5 dc
Last Answer : c. d = 1.19 dc
Description : Nominal size of the discharge pipe of a pump is usually __________ the nominal size of the inlet pipe. (A) Smaller than (B) Larger than (C) Same as (D) Twice
Last Answer : (A) Smaller than
Description : A tube is specified by its (A) Thickness only (B) Outer diameter only (C) Thickness & outer diameter both (D) Inner diameter
Last Answer : (C) Thickness & outer diameter both
Description : The outer and inner diameters of a circular pipe are 6 cm and 4 cm respectively. If its length is 10 cm, then what is the total surface -Maths 9th
Last Answer : answer:
Description : The schedule number of a pipe is an indication of its (A) Size (B) Roughness (C) Material density (D) Wall thickness
Last Answer : (D) Wall thickness
Description : The nominal size of a hose pipe is specified by its (A) I.D. (B) O.D. (C) Thickness (D) None of these
Last Answer : (A) I.D.
Description : With increase in the schedule number of a pipe of a particular nominal size, the (A) Wall thickness also increases (B) I.D. of the pipe decreases (C) O.D. of the pipe remains constant (D) All (A), (B) and (C)
Last Answer : (D) All (A), (B) and (C)
Description : The pipe wall thickness is minimum for a pipe of given nominal size having schedule number (A) 160 (B) 120 (C) 80 (D) 40
Last Answer : (D) 40
Description : A fluid is flowing inside the inner tube of a double pipe heat exchanger with diameter 'd'. For a fixed mass flow rate, the tube side heat transfer coefficient for turbulent flow conditions is proportional to (A) d 0.8 (B) d -0.2 (C) d -1 (D) d -1.8
Last Answer : (B) d -0.2
Description : A washer is specified by (A) Outer diameter (B) Inner diameter (C) Thickness (D) Mean diameter
Last Answer : (B) Inner diameter
Description : If the strain energy stored per unit volume in a hollow shaft subjected to a pure torque when t attains maximum shear stress fs the ratio of inner diameter to outer diameter, is 17/64 (fs/N) (A) 1/2 (B) 1/3 (C) 1/4 (D) 1/5
Last Answer : (C) 1/4
Description : How To Calculate Bearing Number Ti Diameter Of The Inner And Outer?
Last Answer : Divide the shaft diameter size by 5, it will give last two digit of the bearing no. and according to type of load we have to choose the type of bearing and that will give prior number of the bearing.
Description : A hollow shaft has an inner diameter of 3.7 cm and an outer diameter of 4.0 cm. A 1 kN-m torque is applied to this shaft. What is the shear stress at the mid-radius of this shaft? (a) 117Mpa (b) 178 Mpa (c) 286 Mpa (d) 363 Mpa
Last Answer : (c) 286 Mpa
Description : A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum permissible angle of twist in the shaft is 1o. The inner diameter of the shaft is 0.7 times the outer diameter. The modulus of ... shaft is _______. (a) 43 to 45 (b) 50to 60 (c) 70 to 80 (d) 85 to 100
Last Answer : (a) 43 to 45
Description : What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2
Last Answer : c. 20.120 N/mm2
Description : The torque transmitted by a hollow shaft of outer diameter (D) and inner diameter (d) (a)π/4fs(D2-d2)/D (b) π/4fs(D3-d3)/D (c) π/4fs(D4-d4)/D (d) π/4fs(D4-d4)/D
Last Answer : (c) π/4fs(D4-d4)/D
Description : The polar moment of inertia of a hollow shaft of outer diameter (D) and inner diameter (d) is given by. (a)π/16(D3-d3) (b) π/16(D4-d4) (c) π/16(D4-d4) (d) π/16(D4-d4/d)
Last Answer : (b) π/16(D4-d4)
Description : The ratio of strength of a hollow shaft to that of a solid shaft subjected to torsion if both are of the same material and of the same outer diameters, the inner diameter of hollow shaft being half of the outer diameter is a. 15/16 b. 16/15 c. 7/8 d. 8/7
Last Answer : a. 15/16
Description : All pipes of a particular nominal size have the same (A) Inside diameter (B) Outside diameter (C) Thickness (D) None of these
Last Answer : (B) Outside diameter
Description : When the term "nominal size" is used to describe a component under ASME B16.5, what does this indicate? a) A dimension. b) A size designation. c) The inside diameter. d) The flange bolt circle.
Last Answer : b) A size designation.
Description : For lapped joints, which of the following is the minimum finished height of face? a) Not less than the nominal pipe wall. b) Not less than .25". c) At least .060". d) 3/8".
Last Answer : a) Not less than the nominal pipe wall.
Description : For high level flush the nominal dia of flush pipe shall be (a) 32 mm* (b) 40 mm (c) 25 mm (d) None of these
Last Answer : a) 32 mm*
Description : If h1 = inner film co-efficient and /h2 = outer film co-efficient, then the overall heat transfer co-efficient is (A) Always less than h1 (B) Always between h1 and h2 (C) Always higher than h2 (D) Dependent on metal resistance
Last Answer : (B) Always between h1 and h2
Description : . The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C ... from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175
Last Answer : (A) 165.4
Description : A sphere of radius 'R1 ' is enclosed in a sphere of radius 'R2 '. The view (or shape) factor for radiative heat transfer of the outer sphere with respect to the inner sphere is (A) 0 (B) R2 /(R1+R2 ) (C) 1 (D) (R1 /R2 )
Last Answer : (B) R2 /(R1+R2 )
Description : Heat flow across a hollow sphere of inner radius 'r1' and outer radius 'r2' is directly proportional to (A) (r2- r1)/r1. r2 (B) r1. r2/(r2- r1) (C) (r2 + r1)/r1. r2 (D) r1. r2/(r2 + r1)
Last Answer : (B) r1. r2/(r2- r1)
Description : Vena-contracta pressure tapping is at a distance __________ from the position of an orificemeter fitted in a pipe of internal diameter 'd' (A) d (B) 0.5 d (C) 2d (D) 4d
Last Answer : (B) 0.5 d
Description : For pipe flows, head is proportional to __________ at constant capacity(where, D = pipe diameter). (A) 1/D (B) 1/D2 (C) 1/D5 (D) D
Last Answer : (C) 1/D5
Description : The fluid velocity varies as the cube of the cylindrical pipe diameter in case of steady state laminar flow at constant pressure drop for __________ fluid. (A) Newtonian (B) Pseudo-plastic (C) Dilatent (D) Bingham plastic
Last Answer : (B) Pseudo-plastic
Description : Identification of pipelines carrying different liquids and gases is done by the __________ of the pipe. (A) Diameter (B) Colour (C) Altitude (D) None of these
Last Answer : (B) Colour
Description : Transition length for turbulent flow in smooth pipe is equal to __________ times the pipe diameter. (A) 0.5 (B) 5 (C) 50 (D) 500
Last Answer : (C) 50
Description : The fluid velocity varies as the square of the cylindrical pipe diameter, in case of steady state laminar flow at constant pressure drop, for __________ fluid. (A) Newtonian (B) Dilatant (C) Pseudo-plastic (D) Non-Newtonian
Last Answer : (A) Newtonian
Description : The fluid velocity varies as the square root of the cylindrical pipe diameter in case of steady state laminar flow at constant pressure drop of __________ fluid. (A) Dilatent (B) Pseudo-plastic (C) Bingham plastic (D) Newtonian
Last Answer : (A) Dilatent
Description : The maximum discharge through a circular channel takes place, when the depth of the fluid flow is __________ times the pipe diameter. (A) 0.25 (B) 0.5 (C) 0.66 (D) 0.95
Last Answer : (D) 0.95
Description : Transition length for a turbulent fluid entering into a pipe is around __________ times the pipe diameter. (A) 5 (B) 50 (C) 500 (D) 5000
Last Answer : (B) 50
Description : The inner diameter of washer is (A) Equal to the nut size (B) More than the nut size (C) Less than the nut size (D) Independent of the nut size
Last Answer : (B) More than the nut size
Description : If core diameter of bolt is 13.8cm the it’s nominal diameter is given by? a) 17.27mm b) 15.34mm c) 14.67mm d) 16.34mm
Last Answer : a) 17.27mm
Description : In a co-current double pipe heat exchanger used for condensing saturated steam over the inner tube, if the entrance and exit conditions of the coolant are interchanged, then the rate of condensation ... Decrease (C) Remain unchanged (D) Either increase or decrease; depends on the coolant flow rate
Last Answer : (C) Remain unchanged
Description : The outer and the inner radii of a hollow sphere are 12 cm and 10 cm. Find its volume. -Maths 9th
Last Answer : This answer was deleted by our moderators...
Description : The figure below shows the structure of a mitochondrion with its four parts labelled A, B, C and D. Select the part correctly matched with its function. D B A C (a) D (outer ... possesses single circular DNA molecule and ribosomes (d) A (matrix) - major site for respiratory chain enzyme
Last Answer : (b) B (inner membrane) – forms infoldings called cristae
Description : A vessel is said to be thin if a. Its wall has less thickness b. Stresses are uniform over the entire thickness c. Stresses vary at inner and at outer radius d. None of the above
Last Answer : b. Stresses are uniform over the entire thickness
Description : A compound pipe of diameter d1, d2 and d3 having lengths l1, l2 and l3 is to be replaced by an equivalent pipe of uniform diameter d and of the same length (l) as that of the compound pipe. The size of the equivalent pipe is given by (A) l/d² = + + (B) l/d³ = + ) + (C) = + + (D)
Last Answer : Answer: Option D
Description : Nominal diameter of the screw thread is the same as core diameter. a) True b) False
Last Answer : b) False
Description : Pick up the wrong nominal internal diameter of cast iron (spun) pipes in mm from the following: (A) 300 (B) 400 (C) 550 (D) 650
Last Answer : (C) 550