Draw the structure and state applications of: i) Ferrite loop (rod) antenna ii) Horn antenna

Draw the structure and state applications of: i) Ferrite loop (rod) antenna ii) Horn antenna
by

1 Answer

Answer :

Horn antenna:

Application:-

i) Used at microwave frequency.

ii) Used in satellite tracking. 

image

Ferrite loop antenna:

Application:-

In Am radio receiver to receive MW and SW band signals.

In FM radio receiver

image

by

Related questions

Draw radiation pattern for following antenna i) Yagi-Uda antenna ii) Loop antenna iii) Dish antenna iv) Horn antenna

Description : Draw radiation pattern for following antenna i) Yagi-Uda antenna ii) Loop antenna iii) Dish antenna iv) Horn antenna

Last Answer : Type of antenna Radiation Patteren  Yagi-Uda antenna Loop antenna Dish antenna Horn antenna 

Draw the structure of horn antenna and its radiation pattern. List its any two applications.

Description : Draw the structure of horn antenna and its radiation pattern. List its any two applications.

Last Answer : The structure of horn antenna Radiation pattern of Horn Antenna Application:- i) Used at microwave frequency. ii) Used in satellite tracking 

Explain loop antenna with neat sketch. Draw radiation pattern. State its advantages and applications.

Description : Explain loop antenna with neat sketch. Draw radiation pattern. State its advantages and applications.

Last Answer : Loop antenna:-The single turn coil carrying RF current through it having length less than the wavelength.   Advantages:- 1. highly directive 2. Small size Applications:- 1. For direction finding 2. In portable receivers 3. In navigation 

Write one application of following antenna i. Rectangular antenna ii. Dish antenna iii. Yagi-Uda antenna iv. Horn antenna

Description : Write one application of following antenna i. Rectangular antenna ii. Dish antenna iii. Yagi-Uda antenna iv. Horn antenna 

Last Answer : i. Rectangular antenna is used in direction finding in portable recievers. ii. Dish antenna is used to transmit and receive signal from satellite. iii. Yagi-Uda antenna is used in HF and VHF range as a TV receiving antenna. iv. Horn antenna is used in satellite tracking.

Draw the radiation pattern for Dipole antenna: (i) Half wave dipole (ii) Folded dipole.

Description : Draw the radiation pattern for Dipole antenna: (i) Half wave dipole (ii) Folded dipole.

Last Answer : The radiation pattern for Half wave dipole antenna The radiation pattern for Folded dipole antenna.

Draw construction of Yagi-Uda antenna and explain.

Description : Draw construction of Yagi-Uda antenna and explain.

Last Answer : Explanation A Yagi-Uda antenna, commonly known as a Yagi antenna, is a directional antenna consisting of multiple parallel elements in a line, usually half-wave dipoles made of ... receiver with a transmission line and additional parasitic elements called reflector and one or more directors.

Draw Yagiuda antenna with its radiation pattern.

Description : Draw Yagiuda antenna with its radiation pattern.

Last Answer : Construction of Yagi-Uda Antenna Radiation Pattern of Yagi-Uda Antenna

Dish antenna is parabolic in shape and has meshy structure. Give reasons.

Description : Dish antenna is parabolic in shape and has meshy structure. Give reasons.

Last Answer : A Practical reflector employing the properties of the parabola will be a three dimensional bowl-shaped surface, obtained by revolving the parabola about the axis AB. The resulting geometric ... (directrix) is constant. These geometric properties yield an excellent microwave or light reflector. 

A telephone cable has following primary constants per loop kilometer ,R=30Ω, L=20mH,C=0.06µF,G=0.If the applied signal has an angular frequency of 5000 rad/sec.., Determine (i) Characteristics impedence (ii) Attenuation constant

Description : A telephone cable has following primary constants per loop kilometer ,R=30Ω, L=20mH,C=0.06µF,G=0.If the applied signal has an angular frequency of 5000 rad/sec.., Determine (i) Characteristics impedence (ii) Attenuation constant

Last Answer : A telephone cable has following primary constants per loop kilometer ,R=30Ω, L=20mH,C=0.06µF,G=0.If the applied signal has an angular frequency of 5000 rad/sec.., Determine (i) Characteristics impedence (ii) Attenuation constant

Define the following terms related to antennas; (i) Antenna resistance (ii) Directivity (iii) Antenna gain (iv) Power density

Description : Define the following terms related to antennas; (i) Antenna resistance (ii) Directivity (iii) Antenna gain (iv) Power density

Last Answer : Antenna Resistance - The resistance of an antenna has two components: 1. Its radiation resistance due to conversion of power into electromagnetic waves 2. The resistance due to actual losses in the ... the transmitter power divided by the surface area of a sphere (4πR2) at that distance.

Describe with respect to antenna (i) radiation pattern (ii) directive gain (iii) power gam (iv) polarization

Description : Describe with respect to antenna (i) radiation pattern (ii) directive gain (iii) power gam (iv) polarization

Last Answer : (i) Radiation pattern:-A graph or diagram which tells us about the manner in which an antenna radiates more power in different directions is known as the radiation patteren of antenna.  ( ... as the direction of the electric vector in the electromagnetic wave radiated by the transmitting antenna. 

Define the following terms: (i) Polarization (ii) Antenna gain (iii)Antenna resistance (iv)Directivity

Description : Define the following terms: (i) Polarization (ii) Antenna gain (iii)Antenna resistance (iv)Directivity

Last Answer : i) Polarization:- It is defined as the direction of electric field vector in the EM wave radiated by the transmitting antenna. ii) Antenna Gain:- Antenna gain is defined as the ratio of ... in only one direction in which the radiation is maximum. That is directivity = Max. directive gain

In a FM system, the maximum deviation is 75KHz. Find bandwidth for modulating frequency i. fm=500Hz ii. fm=5KHz iii. fm=10KHz Draw conclusion for bandwidth of FM from answer.

Description : In a FM system, the maximum deviation is 75KHz. Find bandwidth for modulating frequency i. fm=500Hz ii. fm=5KHz iii. fm=10KHz Draw conclusion for bandwidth of FM from answer.

Last Answer : Given deviation∆=75kHz i) fm=500Hz bandwidth B.W=2(∆+fm)  =2(75k+500)=151kHz  ii). fm=5KHz bandwidth B.W=2(∆+fm)  =2(75k+5k)=160KHz iii) fm=10KHz bandwidth B.W=2(∆+fm)  =2(75k+10k)=170KHz As the modulating frequency increases bandwidth also increases.

Define and explain the term beam width related to antenna with a sketch.

Description : Define and explain the term beam width related to antenna with a sketch.

Last Answer : Definition: The beam width of an antenna is described as the angles created by comparing the half power point (3dB) on the main radiation lobe to its maximum power point. As an example the beam width ... max voltage at center of lobe (these point are known as half power points.) Sketch-  

Explain how modulation reduces height of antenna and avoid mixing of signals.

Description : Explain how modulation reduces height of antenna and avoid mixing of signals.

Last Answer : Modulation reduces antenna height: For the transmission of radio signals, the antenna height must be multiple of λ/4 ,where λ is the wavelength . λ = c /f where c : is the ... will occupy different slots in the frequency domain (different channels). Thus, modulation avoids mixing of signals.

Explain half dipole antenna ( Resonant antenna ) with its radiation patteren.

Description : Explain half dipole antenna ( Resonant antenna ) with its radiation patteren. 

Last Answer : Half wave dipole antenna Explanation:  1. It is a resonant antenna 2. It is exact half wavelength (λ /2) long & open circuited at one end. 3. The dipole antennas have ... pattern is bidirectional.  The radiation pattern of half wave dipole antenna is - The radiation pattern

An antenna has a radiation resistance of 72 Ω a loss resistance of 8 Ω and a power gain of 16. Find efficiency and directivity.

Description : An antenna has a radiation resistance of 72 Ω a loss resistance of 8 Ω and a power gain of 16. Find efficiency and directivity.

Last Answer : An antenna has a radiation resistance of 72 Ω a loss resistance of 8 Ω and a power gain of 16. Find efficiency and directivity.

Define pre-emphasis. State its need. Draw the circuit of pre-emphasis.

Description : Define pre-emphasis. State its need. Draw the circuit of pre-emphasis.

Last Answer : Definition- The artificial boosting of higher modulating frequencies to reduce the effect of noise is called as pre-emphasis. Need:- The artificial boosting of higher audio modulating ... by increasing the amplitude of modulating signal at higher frequencies. Circuit diagram 

Draw the circuit diagram of PWM using IC555. State its operation.

Description : Draw the circuit diagram of PWM using IC555. State its operation.

Last Answer : Operation: i. The timer IC555 is operated in monostable mode. ii. The negative going carrier pulses are to the differentiator formed by R1 & C1. The differentiator produces sharp negative ... . Thus PWM signal is generated at the output pin (3) of IC555 as monostablemultivibrator. 

Draw block diagram of basic electronic communication system and state the function of each block.

Description : Draw block diagram of basic electronic communication system and state the function of each block.

Last Answer : i) Input signal: - The information can be in the form of sound, picture or data coming from computer. ii) Input transducer: - it converts original information into equivalent electrical ... back to suitable form. vii) Output transducer: - It converts electrical signal into original form. 

Explain any four different frequency bands and give their two applications of each.

Description : Explain any four different frequency bands and give their two applications of each.

Last Answer : Explain any four different frequency bands and give their two applications of each.

Write the application of the following antennas: 1) Rectangular antenna 2) Dish antenna 3) Horn antenna 4) Loop antenna 5) Yagi-Uda antenna.

Description : Write the application of the following antennas: 1) Rectangular antenna 2) Dish antenna 3) Horn antenna 4) Loop antenna 5) Yagi-Uda antenna. 

Last Answer : Applications:  1.Rectangular antenna  i)Used in Mobile and satellite communication ii)Used in Global Positioning System iii) Used for Radio Frequency Identification (RFID) iv) Radar  Dish ... antenna. 2. Yagi-Uda antenna is used in conditional Access System (CAS) at the decryptor.

Draw practical set-up and explain the procedure to measure selectivity of radio receiver.

Description : Draw practical set-up and explain the procedure to measure selectivity of radio receiver.

Last Answer : Procedure to measure selectivity of radio receiver: Throughout the measurement the receiver is kept tuned to desired frequency 950 Khz. Now the generator output frequency is deviated below ... the generator output voltage is adjusted to get a standard 50 miliwatt receiver output power.

Draw and label the circuit diagram of ratio detector

Description : Draw and label the circuit diagram of ratio detector 

Last Answer : Draw and label the circuit diagram of ratio detector  

Draw circuit diagram of transistor reactance modulator. Explain its working.

Description : Draw circuit diagram of transistor reactance modulator. Explain its working.

Last Answer : Explanation- A reactance modulator is illustrated in figure. It is basically a standard commonemitter class A amplifier. Resistors R1 and R2 from a voltage divider to bias ... frequency, whereas a lower capacitance increases the frequency. The circuit produces direct frequency modulations.

Draw block diagram of FM receiver and explain the use of limiter circuit.

Description : Draw block diagram of FM receiver and explain the use of limiter circuit.

Last Answer : Diagram Explanation Amplitude limiter: The function of amplitude limiter is to remove all amplitude variation of FM carrier voltage that may occur due to atmospheric disturbances. Use of amplitude limiter makes the system less noisy.

Draw waveform for standing waves on an open and shorted line. Prove that impedance is inverted at every quarter wavelength interval.

Description : Draw waveform for standing waves on an open and shorted line. Prove that impedance is inverted at every quarter wavelength interval.

Last Answer : Waveform- Explanation When the transmission line is short circuited voltage is zero and current is maximum.The variation is according to the wavelength. When the ... The pattern repeats for every half wavelength. Thus impedance is inverted at every quarter wavelength interval.

Define PAM, PWM, and PPM. Draw waveforms.

Description : Define PAM, PWM, and PPM. Draw waveforms.

Last Answer : Pulse amplitude modulation is defined as a process of varying the amplitude of the carrier pulse in accordance to the modulating signal variations. Pulse width modulation is defined as a ... of varying the position of the carrier pulse, in accordance to the modulating signal variations.

Define the transmission line? Draw it‟s general equivalent circuit.

Description : Define the transmission line? Draw it‟s general equivalent circuit.

Last Answer : Transmission line: A conductor or conductors designed to carry electricity or an electrical signal over large distances with minimum losses and distortion.  Equivalent circuit:

Draw and explain block diagram of electronic communication system.

Description : Draw and explain block diagram of electronic communication system.

Last Answer : Block diagram of electronic communication system. Explanation Transducer: A transducer is usually required to convert the output of a source into an electrical signal that is suitable for ... etc. Output Transducer: The output transducer converts electrical signal in to sound signal.  

Draw and explain PLL as an FM demodulator.

Description : Draw and explain PLL as an FM demodulator.

Last Answer : Explanation:- FM signal which is to be demodulated is applied to input of PLL.VCO output must be identical to input signal if PLL is to remain locked. As PLL is locked, VCO ... error voltage represents the modulating signal. Thus at the error amplifier output we get demodulated FM output.

Draw the circuit diagram of practical diode detector and explain its working.

Description : Draw the circuit diagram of practical diode detector and explain its working. 

Last Answer : Circuit diagram of practical diode detector:  Explanation- The circuit operates in the following manner- The diode has been reversed so that now the negative envelope is demodulated. Due to this ... to produce AGC voltage. The DC AGC voltage is proportional to the amplitude of AM signal. 

Draw general equivalent circuit of transmission line.

Description : Draw general equivalent circuit of transmission line.

Last Answer : Fig. General Equivalent circuit of transmission line 

Draw the circuit diagram of limiter and explain its working.

Description : Draw the circuit diagram of limiter and explain its working.

Last Answer : Circuit diagram of amplitude limiter:- Explanation:- 1. In frequency modulation, the signal amplitude is held constant while the carrier frequency is varied. 2. Any noise that contaminates ... V p-p instead of the alternately driven into saturation and cutoff, it limits the signal amplitude

Draw the TRF receiver block diagram and explain its working.

Description : Draw the TRF receiver block diagram and explain its working. 

Last Answer : Explanation:- 1. TRF receivers are simple and having high sensitivity. The AM transmission takes place in MW band and SW band. MW frequency range is 540KHz to 1640KHz. 2. ... power level to drive the loudspeaker. 7. The loudspeaker converts electrical signal into original sound information.

Draw the diagram for PAM generation using transistors. Explain its working.

Description : Draw the diagram for PAM generation using transistors. Explain its working.

Last Answer : Explanation:-1. Transistor Q1 is used in the active region so it has been provided with DC biasing to its base. 2. Modulating signal is applied to the base of transistor Q1 3. In the emitter of ... . 7. In the time interval between sampling pulses output is zero. Thus we get the output as PAM.

Draw the block diagram of FM super heterodyne radio receiver with waveforms.

Description : Draw the block diagram of FM super heterodyne radio receiver with waveforms.

Last Answer : block diagram of FM super heterodyne radio receiver

Draw the circuit diagram of varactor diode FM modulator and explain its working.

Description : Draw the circuit diagram of varactor diode FM modulator and explain its working.

Last Answer : Varactor diode modulator is the direct method of FM generation wherein the carrier frequency is directly varied by the modulating signal. A varactor diode is a semiconductor diode whose ... the magnitude of frequency change is proportional to the amplitude of the modulating signal voltage.

Draw the block diagram of PWM. List its advantages

Description : Draw the block diagram of PWM. List its advantages 

Last Answer : Block diagram of PWM:- Advantages of PWM:- 1. More immune to noise. 2. Synchronization between transmitter and receiver is not required. 3. Possible to separate out signal from noise.

Draw the block diagram of AM transmitter, explain its operation.

Description : Draw the block diagram of AM transmitter, explain its operation.

Last Answer : AM transmitter is of two types i)High Level AM Transmitter ii)Low Level AM Transmitter i) RF crystal oscillator: It is a source of carrier signal of desired frequency. The circuit is ... AM signal is then applied to the transmitting antenna which radiates this AM signal into air or space. 

Draw amplitude modulated waveform in time domain and frequency domain with proper labeling.

Description : Draw amplitude modulated waveform in time domain and frequency domain with proper labeling.

Last Answer : AM in Time domain  AM in frequency domain

In order to get maximum radiation to all surrounding points in the horizontal plane, the antenna used is a A. vertical loop B. vertical quarter-wavelength rod C. array which includes parasitic elements D. a horizontal Hertz dipole

Description : In order to get maximum radiation to all surrounding points in the horizontal plane, the antenna used is a A. vertical loop B. vertical quarter-wavelength rod C. array which includes parasitic elements D. a horizontal Hertz dipole

Last Answer : B. vertical quarter-wavelength rod

A superheterodyne radio receiver with an IF of 455KHZ is turned to 1000KHZ. Find: (i) Image frequency (ii) Local oscillator frequency

Description : A superheterodyne radio receiver with an IF of 455KHZ is turned to 1000KHZ. Find: (i) Image frequency (ii) Local oscillator frequency

Last Answer : Given Intermediate Frequency fi=455KHz Signal frequency =fs=1000KHz Local oscillator frequency fo=fs+fi  Fo=1000KHz+455KHz  =1455KHz Image frequency is the input frequency which produces the same intermediate frequency fsi=fs+2fi  =1000KHz+2*455KHz  =1910KHz 

Compare PAM, PWM, and PPM on the basis of i. Variable characteristics ii. Bandwidth iii. Information contained in iv. Transmitted power

Description : Compare PAM, PWM, and PPM on the basis of i. Variable characteristics ii. Bandwidth iii. Information contained in iv. Transmitted power

Last Answer : Compare PAM, PWM, and PPM on the basis of i. Variable characteristics ii. Bandwidth iii. Information contained in iv. Transmitted power

a) For a transmission line, Find SWR and reflection coefficient R if, i. There is no reflected voltage. ii. Reflected voltage and incident voltage is equal. iii. If reflected voltage=20V and incident voltage=10V. iv. If reflected voltage=10V and incident voltage =20V.

Description : a) For a transmission line, Find SWR and reflection coefficient R if, i. There is no reflected voltage. ii. Reflected voltage and incident voltage is equal. iii. If reflected voltage=20V and incident voltage=10V. iv. If reflected voltage=10V and incident voltage =20V.

Last Answer : reflection coefficient R=Vr/Vi i. There is no reflected voltage. i.e,Vr=0 R=0 SWR= 1+R/1-R=1 ii. Reflected voltage and incident voltage is equal. Vr=Vi; R=1 SWR= 1+R/1-R=1+1/1-1=infinity iii. If reflected ... and incident voltage =20V. Vr=10 and Vi=20 R=10/20=0.5 SWR= 1+R/1-R=1+.5/1-.5=3 

Differentiate between AM and FM on the basis of: (i) Definition (ii) Bandwidth (iii) Modulation Index (iv) Application

Description : Differentiate between AM and FM on the basis of: (i) Definition (ii) Bandwidth (iii) Modulation Index (iv) Application

Last Answer : Compare AM and FM on the basis of i)Definition ii)Bandwidth iii) Wave propogation iv)Number of sidebands

Compare ground wave and space wave propagation on the basis of: (i) Frequency range (ii) Method of propagation.

Description : Compare ground wave and space wave propagation on the basis of: (i) Frequency range (ii) Method of propagation.

Last Answer : Compare ground wave and space wave propagation on the basis of: (i) Frequency range (ii) Method of propagation.

Explain the following characteristics of AM radio receiver: (i) Sensitivity (ii) Selectivity.

Description : Explain the following characteristics of AM radio receiver: (i) Sensitivity (ii) Selectivity.

Last Answer : Sensitivity:- The ability to amplify the weak signals is called sensitivity. It is the function of overall receiver gain. Sensitivity of radio receiver is decided by the gain of the RF IF ... perfectly the receiver is able to select the desired carrier frequency and reject other frequencies. 

For AM, fc =500kHz , fm = 5 kHz Determine: (i) Upper and lower sideband frequencies (ii) Bandwidth

Description : For AM, fc =500kHz , fm = 5 kHz Determine: (i) Upper and lower sideband frequencies (ii) Bandwidth

Last Answer : Given data fc = 500KHz , fm = 5KHz USB =fc+fm USB = 500+5  =505 KHz. LSB =fc – fm LSB = 500 – 5  =495 KHz Bandwidth = 2fm .  = 2* 5 =10 KHz

For a transmission line, the incident voltage. Ei = 6V and Er =2V ,Calculate: (i) Reflection Coefficient (ii) SWR

Description : For a transmission line, the incident voltage. Ei = 6V and Er =2V ,Calculate: (i) Reflection Coefficient (ii) SWR

Last Answer : Reflection Coefficient(K) = Er / Ei  = 2V / 6V  K = 0.333 SWR = 1+K / 1- K  = 1+0.333 / 1-0.333  = 1.333 / 0.667 SWR= 1.998