Description : Copper is dissolved from its ore by H2SO4 in a percolation tank made of (A) Wood (B) Stainless steel (C) Reinforced concrete lined with lead (D) High silicon iron (14% Si)
Last Answer : (C) Reinforced concrete lined with lead
Description : Cast iron detachable joint is used in __________ pipes. (A) Steel (B) Cast iron (C) Asbestos cement (D) Reinforced cement concrete
Last Answer : (A) Steel
Description : Steel rods are used in reinforced concrete to increase its __________ strength. (A) Shear (B) Tensile (C) Compressive (D) None of these
Last Answer : (B) Tensile
Description : If a concrete column 200 200 mm in cross-section is reinforced with four steel bars of 1200 mm2 total cross-sectional area. Calculate the safe load for the column if permissible stress in concrete is 5 N/mm2 ... 15 Ec (A) 264 MN (B) 274 MN (C) 284 MN (D) 294 MN
Last Answer : (C) 284 MN
Description : A reinforced concrete beam is assumed to be made of (A) Homogeneous material (B) Heterogeneous material (C) Isotropic material (D) None of these
Last Answer : (B) Heterogeneous material
Description : _________ pipe is the most suitable for carrying sanitary drainage. (A) Stainless steel (B) Reinforced cement concrete (C) Cast iron (D) Asbestos cement
Last Answer : C) Cast iron
Description : A pre-stressed concrete member (A) Is made of concrete (B) Is made of reinforced concrete (C) Is stressed after casting (D) Possesses internal stresses
Last Answer : Answer: Option D
Description : If permissible working stresses in steel and concrete are respectively 1400 kg/cm2 and 80 kg/cm2 and modular ratio is 18, in a beam reinforced in tension side and of width 30 cm and having effective depth 46 cm, the lever arms of the section, is (A) 37 cm (B) 38 cm (C) 39 cm (D) 40 cm
Description : The reinforced concrete beam which has width 25 cm, lever arm 40 cm, shear force 6t/cm2 , safe shear stress 5 kg/cm2 and B.M. 24 mt, (A) Is safe in shear (B) Is unsafe in shear (C) Is over safe in shear (D) Needs redesigning
Last Answer : Answer: Option B
Description : Steel beam theory is used for (A) Design of simple steel beams (B) Steel beams encased in concrete (C) Doubly reinforced beams ignoring compressive stress in concrete (D) Beams if shear exceeds 4 times allowable shear stress
Last Answer : Answer: Option C
Description : A short column 20 cm 20 cm in section is reinforced with 4 bars whose area of cross section is 20 sq. cm. If permissible compressive stresses in concrete and steel are 40 kg/cm2 and 300 kg/cm2 , the Safe load on ... should not exceed (A) 4120 kg (B) 41,200 kg (C) 412,000 kg (D) None of these
Description : In a singly reinforced beam, if the permissible stress in concrete reaches earlier than that in steel, the beam section is called (A) Under-reinforced section (B) Over reinforced section (C) Economic section (D) Critical section
Description : The maximum shear stress (q) in concrete of a reinforced cement concrete beam is (A) Shear force/(Lever arm × Width) (B) Lever arm/(Shear force × Width) (C) Width/(Lever arm × Shear force) (D) (Shear force × Width)/Lever arm
Last Answer : Answer: Option A
Description : According to I.S.: 456, 1978 the thickness of reinforced concrete footing on piles at its edges, is kept less than (A) 20 cm (B) 30 cm (C) 40 cm (D) 75 cm
Description : The section of a reinforced beam where most distant concrete fibre in compression and tension in steel attains permissible stresses simultaneously, is called (A) Balanced section B) Economic section (C) Critical section (D) All the above
Description : The weight of reinforced concrete, is generally taken as (A) 2200 kg/m3 (B) 2300 kg/m3 (C) 2400 kg/m3 (D) 2500 kg/m
Description : A singly reinforced concrete beam of 25 cm width and 70 cm effective depth is provided with 18.75 cm2 steel. If the modular ratio (m) is 15, the depth of the neutral axis, is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm
Description : If the depth of actual neutral axis of a doubly reinforced beam (A) Is greater than the depth of critical neutral axis, the concrete attains its maximum stress earlier (B) Is less ... critical neutral axis; the concrete and steel attain their maximum stresses simultaneously (D) All the above
Description : The stresses developed in concrete and steel in reinforced concrete beam 25 cm width and 70 cm effective depth, are 62.5 kg/cm2 and 250 kg/cm2 respectively. If m = 15, the depth of its neutral axis is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm
Description : A reinforced concrete cantilever beam is 3.6 m long, 25 cm wide and has its lever arm 40 cm. It carries a load of 1200 kg at its free end and vertical stirrups can carry 1800 kg. Assuming concrete to carry one- ... beam, the number of shear stirrups required, is (A) 30 (B) 35 (C) 40 (D) 45
Description : In a singly reinforced beam (A) Compression is borne entirely by concrete (B) Steel possesses initial stresses when embedded in concrete (C) Plane sections transverse to the centre line ... Elastic moduli for concrete and steel have different values within the limits of deformation of the beam
Description : According to I.S.: 456, 1978 the thickness of reinforced concrete footing on piles at its edges, is kept less than (A) 5 cm (B) 10 cm (C) 15 cm (D) 20 cm
Description : The advantage of reinforced concrete, is due to (A) Monolithic character (B) Fire-resisting and durability (C) Economy because of less maintenance cost (D) All the abov
Description : The allowable tensile stress in mild steel stirrups, reinforced cement concrete, is (A) 1400 kg/cm2 (B) 190 kg/cm2 (C) 260 kg/cm2 (D) 230 kg/cm
Description : Large diameter reinforced cement concrete (RCC) pipes are generally joined by __________ joint. (A) Flanged iron (B) Collar (C) Flexible (D) Expansion
Last Answer : Option B
Description : In reinforced concrete footing on soil, the minimum thickness at edge should not be less than (A) 100 mm (B) 150 mm (C) 200 mm (D) 250 mm
Description : Higher workability of concrete is required if the structure is (A) Made with cement concrete (B) Thick and reinforced (C) Thin and heavily reinforced (D) Thick and heavily reinforced
Description : Minimum grade of concrete to be used in reinforced concrete as per IS: 4561978 is (A) M 15 (B) M 20 (C) M 10 (D) M 25
Description : If the permissible stress in steel in tension is 140 N/mm², then the depth of neutral axis for a singly reinforced rectangular balanced section will be (A) 0.35 d (B) 0.40 d (C) 0.45 d (D) Dependent on grade of concrete also
Description : In symmetrically reinforced sections, shrinkage stresses in concrete and steel are respectively (A) Compressive and tensile (B) Tensile and compressive (C) Both compressive (D) Both tensile
Description : For concreting of heavily reinforced sections without vibration, the workability of concrete expressed as compacting factor should be (A) 0.75 - 0.80 (B) 0.80 - 0.85 (C) 0.85 - 0.92 (D) Above 0.92
Description : Expanded metal is (A) Manufactured from steel sheets (B) Used for reinforced concrete in road pavements (C) Measured in term of SWM (short way mesh) and LWM (long way mesh) (D) All the above
Description : For a reinforced concrete section, the shape of shear stress diagram is (A) Wholly parabolic (B) Wholly rectangular (C) Parabolic above neutral axis and rectangular below neutral axis (D) Rectangular above neutral axis and parabolic below neutral axis
Description : In flat roof of reinforced cement concrete, the recommended angle of slope, is (A) Zero (B) A few degrees (C) 10° (D) 200
Description : For a wall carrying heavy load on low bearing capacity soil, (A) Lean concrete bed is provided (B) Thick concrete bed is provided (C) Reinforced concrete bed is provided (D) Both (a) and (c) of the above
Description : Which among the following are the components of natural draft cooling tower a) Supply basin b) reinforced concrete c) Hot water distribution d) none of the above
Last Answer : reinforced concrete
Description : Hyperbolic cooling towers are made up of high height reinforced ………structure. a) plastic c)metal b) alloy d) concrete
Last Answer : concrete
Description : Consider the following statements: Percentage of steel for balanced designed of a singly reinforced rectangular section by limit state method depends on (1) Characteristic strength of concrete (2) Yield strength of concrete (3) Modulus of elasticity ... (b) 1, 3 and 4 (c) 1, 2 and 4 (d) 1, 2 and 3
Last Answer : 1,2,4
Description : A reinforced concrete cantilever porch has thickness t. The main reinforcing steel will be placed (a) At mid-thickness (b) At t/3 from the top (c) Close to the bottom surface (d) Close to the top surface
Last Answer : (d) Close to the top surface
Description : A reinforced concrete slab is 75 mm thick. The maximum size of reinforcement bar that can be used is (a) 6 mm diameter (b) 8 mm diameter (c) 10 mm diameter (d) 12 mm diameter
Last Answer : (b) 8 mm diameter
Description : Shear resistance of concrete in a reinforced concrete beam is dependent on (a) Tension reinforcement in the beam (b) Compression reinforcement in the beam (c ) Shear reinforcement in the beam (d) None of the reinforcements in the beam
Last Answer : (a) Tension reinforcement in the beam
Description : The weight of reinforced concrete is generally take as (a) 2300 kg/m3 (b) 2400 kg/m3 (c) 2500kg/m3 (d) 2800kg/m3
Last Answer : (d) 2800kg/m3
Description : If the bond stress developed in a reinforced concrete beam is more than permissible value, it can be brought down by. (a) Increasing the depth of beam (b) Increasing the number of bars. (c) Decreasing the diameter of the bars (d) All of these
Last Answer : (d) All of these
Description : The torsion resisting capacity of a given reinforced concrete section. (a) Decreases with decrease in stirrups spacing. (b) Decreases with increase in longitudinal bars. (c) Does not depend upon stirrups and longitudinal steels. (d) Increases with increase in stirrups and longitudinal steels.
Last Answer : (d) Increases with increase in stirrups and longitudinal steels.
Description : For a reinforced concrete beam section, the shape of shear stress diagram is (a) Parabolic over the whole section with maximum value at the neutral axis. (b) Parabolic above the neutral axis and rectangular below the neutral axis. (c) Linearly varying as the distance form the N.A. (d) All the above.
Last Answer : (b) Parabolic above the neutral axis and rectangular below the neutral axis.
Description : In a reinforced concrete beam , the shear stress distribution above the neutral axis following a (a) A straight line (b) Circular curve (c) Parabolic curve (d) All the above
Last Answer : (c) Parabolic curve
Description : Regarding the working stress design of under reinforced concrete section, (a) The neutral axis depth will be greater than that of a balanced section. (b) The stress in steel intension will reach ... on the tension side is also be considered for calculating the moment of resistance of the section.
Last Answer : both b&c
Description : The effective depth of a singly reinforced rectangular beam is 300mm. the section is over-reinforced and the neutral axis is 120mm below the top. If the maximum stress attained by concrete is 5N/mn2 and the modular ratio ... in the steel will (a) 130N/mm2 (b) 135N/mm2 (c) 160N/mm2 (d) 180N/mm2
Last Answer : (b) 135N/mm2
Description : For an over -reinforced (singly reinforced )rectangular reinforced concrete section (a) The lever arm will be less than that for a balanced section (b) The maximum stress developed by concrete will be equal ... c) The maximum stress developed by steel will be equal to the allowable (d) All the above
Last Answer : (b) The maximum stress developed by concrete will be equal to allowable stress in concrete
Description : In an over-reinforced section (a) Steel reinforcement is not fully stressed to its permissible value (b) Concrete is not fully stressed to its permissible value (c) Either (a) and (b) (d) Both (a) and (b)
Last Answer : (a) Steel reinforcement is not fully stressed to its permissible value