If a DC voltmeter is made from an ammeter having a fed of 100μA then its sensitivity (in KΩ/V) will be

by

1 Answer

Answer :

 If a DC voltmeter is made from an ammeter having a fed of 100μA then its sensitivity (in KΩ/V) will be 10.

by

Related questions

A dc voltmeter has a sensitivity of 1000 Ohm/V. When it measures half full scale in 100 V range, the current ...

Description : A dc voltmeter has a sensitivity of 1000 Ohm/V. When it measures half full scale in 100 V range, the current through the voltmeter is

Last Answer : A dc voltmeter has a sensitivity of 1000 Ohm/V. When it measures half full scale in 100 V range, the current through the voltmeter is 1 mA.

An ac voltmeter using full -wave rectification and having a sinusoidal input has an ac sensitivity equal to

Description : An ac voltmeter using full -wave rectification and having a sinusoidal input has an ac sensitivity equal to  (1) 1.414 times dc sensitivity (2) dc sensitivity (3) 0.9 times dc sensitivity (4) 0.707 times dc sensitivity

Last Answer : An ac voltmeter using full -wave rectification and having a sinusoidal input has an ac sensitivity equal to 0.9 times dc sensitivity

If a voltmeter is connected, like an ammeter in series to the load:

Last Answer : If a voltmeter is connected, like an ammeter in series to the load: Almost no current will flow in the circuit

In the circuit shown in figure ammeter and voltmeter are ideal. If `E=4 V,R=9Omega` and `r=1Omega` then readings of ammeter and voltmeter are

Description : In the circuit shown in figure ammeter and voltmeter are ideal. If `E=4 V,R=9Omega` and `r=1Omega` then readings of ammeter and voltmeter are

Last Answer : In the circuit shown in figure ammeter and voltmeter are ideal. If `E=4 V,R=9Omega` and `r=1Omega` then readings of ... V C. 3 A, 4 V D. 4 A, 4 V

In order to increase its range of measurement, a resistance would be placed in series with which of the following instruments? A. DC voltmeter B. DC ammeter C. frequency meter D. power factor meter

Description : In order to increase its range of measurement, a resistance would be placed in series with which of the following instruments? A. DC voltmeter B. DC ammeter C. frequency meter D. power factor meter

Last Answer : Answer: A

An internal resistance is placed in series with the meter movement of which of the following instruments? A. AC ammeter B. DC ammeter C. DC voltmeter D. Frequency meter

Description : An internal resistance is placed in series with the meter movement of which of the following instruments? A. AC ammeter B. DC ammeter C. DC voltmeter D. Frequency meter

Last Answer : Answer: C

In the case of an instrument reading of 8.3 V with a 0 to 150 voltmeter having a guaranteed accuracy of

Description :  In the case of an instrument reading of 8.3 V with a 0 to 150 voltmeter having a guaranteed accuracy of 1% full scale reading, the percentage limiting error is   (A) 1.810% (B) 0.181% (C)12.45% (D) 0.0018%

Last Answer :  In the case of an instrument reading of 8.3 V with a 0 to 150 voltmeter having a guaranteed accuracy of 1% full scale reading, the percentage limiting error is 12.45%

A voltmeter of range 2 V and resistance `300 Omega` cannot be converted into ammeter of range

Description : A voltmeter of range 2 V and resistance `300 Omega` cannot be converted into ammeter of range

Last Answer : A voltmeter of range 2 V and resistance `300 Omega` cannot be converted into ammeter of range A. `1 A` B. `1 mA` C. `100 mA` D. `10 mA`

An ammeter and a voltmeter of resistance `R` connected in seires to an electric cell of negligible internal resistance. Their readings are `A` and `V`

Description : An ammeter and a voltmeter of resistance `R` connected in seires to an electric cell of negligible internal resistance. Their readings are `A` and `V`

Last Answer : An ammeter and a voltmeter of resistance `R` connected in seires to an electric cell of negligible ... increase D. A will increase and V will decrease

An unshielded moving iron voltmeter is used to measure the voltage in an AC circuit. The stray DC magnetic

Description : An unshielded moving iron voltmeter is used to measure the voltage in an AC circuit. The stray DC magnetic field having a component along the axis will be  (1) unaffected (2) decreased (3) increased (4) either decreased or increased depending on the direction of the DC field

Last Answer : An unshielded moving iron voltmeter is used to measure the voltage in an AC circuit. The stray DC magnetic field having a component along the axis will be either decreased or increased depending on the direction of the DC field

A 10A DC Ammeter has a resistance of 0.1 Ω is to be extended to 50 A, the required shunt wire is

Description : A 10A DC Ammeter has a resistance of 0.1 Ω is to be extended to 50 A, the required shunt wire is A) Manganin wire of 20 m Ω B) Constantan wire of 20 m Ω C) Manganin wire of 25 m Ω D) Constantan wire of 25 m Ω

Last Answer : A 10A DC Ammeter has a resistance of 0.1 Ω is to be extended to 50 A, the required shunt wire is Manganin wire of 25 m Ω

A PMMC instrument has FSD of 100 μA and a coil resistance of 1 kΩ. To convert the instrument into an

Description : A PMMC instrument has FSD of 100 μA and a coil resistance of 1 kΩ. To convert the instrument into an ammeter with full scale deflection of 100 mA, the required shunt resistance is (A) 1 Ω (B) 1.001 Ω (C) 0.5 Ω (D) 10 Ω

Last Answer : A PMMC instrument has FSD of 100 μA and a coil resistance of 1 kΩ. To convert the instrument into an ammeter with full scale deflection of 100 mA, the required shunt resistance is 1.001 Ω

A digital voltmeter has a read-out range from 0 to 9999 counts. When full scale reading is 9.999 V, the

Description : A digital voltmeter has a read-out range from 0 to 9999 counts. When full scale reading is 9.999 V, the resolution of the instrument will be (a) 100 mV (b) 99 mV (c) 9 mV (d) 1 mV 

Last Answer : d) 1mV 9.999v÷9999v

A 150 V moving iron voltmeter of accuracy class 1.0 reads 75 V when ...

Description : A 150 V moving iron voltmeter of accuracy class 1.0 reads 75 V when used in a circuit under a standard conditions. The maximum possible percentage error in the reading is:

Last Answer : A 150 V moving iron voltmeter of accuracy class 1.0 reads 75 V when used in a circuit under a standard conditions. The maximum possible percentage error in the reading is:  2.0.

A three-phase, 440 V, 50 Hz ac mains fed thyristor bridge is feeding a 440 V dc, 15 kW, 1500 rpm separately

Description : A three-phase, 440 V, 50 Hz ac mains fed thyristor bridge is feeding a 440 V dc, 15 kW, 1500 rpm separately excited dc motor with a ripple free continuous current in the dc link under all operating conditions, Neglecting the ... at half the rated speed is  (A) 0.354 (B) 0.372 (C) 0.90 (D) 0.955

Last Answer : A three-phase, 440 V, 50 Hz ac mains fed thyristor bridge is feeding a 440 V dc, 15 kW, 1500 rpm separately excited dc motor with a ripple free continuous current in the dc link under all operating conditions, Neglecting the losses, the power factor of the ac mains at half the rated speed is 0.354

The amount of current flowing through a circuit with a 40 V source and 6.8 kΩ of resistance is equal to:

Description : The amount of current flowing through a circuit with a 40 V source and 6.8 kΩ of resistance is equal to: A. 27.2 mA B. 59 mA C. 5.9 mA D. 590 mA

Last Answer : The amount of current flowing through a circuit with a 40 V source and 6.8 kΩ of resistance is equal to:  5.9 mA

The basic meter movement responds to the flow of current through its coil. Therefore, this meter movement may be used as a/an _____________. A. voltmeter by placing a resistance in parallel with the coil B. ohmmeter by placing another meter movement in parallel with the coil C. wattmeter by placing a battery in parallel with the coil D. ammeter by placing a low resistance in parallel with the coil

Description : The basic meter movement responds to the flow of current through its coil. Therefore, this meter movement may be used as a/an _____________. A. voltmeter by placing a resistance in parallel with the ... in parallel with the coil D. ammeter by placing a low resistance in parallel with the coil

Last Answer : Answer: D

When troubleshooting most electronic circuits, 'loading effect' can be minimized by using a voltmeter with a/an ___________________. A. input impedance much greater than the impedance across which the voltage is being measured B. input impedance much less than the impedance across which the voltage is being measured C. sensitivity of less than 1000 ohms/volt D. sensitivity of more than 1000 volts/ohm

Description : When troubleshooting most electronic circuits, 'loading effect' can be minimized by using a voltmeter with a/an ___________________. A. input impedance much greater than the impedance across which the voltage ... sensitivity of less than 1000 ohms/volt D. sensitivity of more than 1000 volts/ohm

Last Answer : Answer: A

What is voltmeter sensitivity?

Description : What is voltmeter sensitivity?

Last Answer : It is an indication of the resistance of the meter expressed in ohms per volt. The total resistance of the meter is the sensitivity multiplied by the full-scale voltage.

What term is used to express the sensitivity of a voltmeter?

Description : What term is used to express the sensitivity of a voltmeter?

Last Answer : Ohms per volt

Explain sensitivity and loading effect in voltmeter.

Description : Explain sensitivity and loading effect in voltmeter.

Last Answer : Sensitivity: The sensitivity of a voltmeter is just its capability to detect voltage, usually meaning smaller and smaller voltages. When selecting a meter for a certain voltage measurement, it is ... called loading effect of the voltmeters. It is mainly caused due to low sensitivity instruments.

Describe following terms w.r.t. Analog voltmeter : (i) Sensitivity (ii) Loading effect

Description : Describe following terms w.r.t. Analog voltmeter : (i) Sensitivity (ii) Loading effect

Last Answer : Sensitivity: The sensitivity of a voltmeter is just its capability to detect voltage, usually meaning smaller and smaller voltages. When selecting a meter for a certain voltage measurement, it is ... called loading effect of the voltmeters. It is mainly caused due to low sensitivity instruments.

An analog voltmeter has a sensitivity of 10kΩ/volt. The galvanometer used in constructing the instrument

Description : An analog voltmeter has a sensitivity of 10kΩ/volt. The galvanometer used in constructing the instrument will produce a full scale deflection when the current passed through it is  (a) 10 mA (b) 20 mA (c) 50 mA (d) 100 μA

Last Answer : An analog voltmeter has a sensitivity of 10kΩ/volt. The galvanometer used in constructing the instrument will produce a full scale deflection when the current passed through it is 100 μA

What is ammeter sensitivity?

Description : What is ammeter sensitivity?

Last Answer : The amount of current that will cause full-scale deflection.

What is meant by Voltmeter & Ammeter ?

Description : What is meant by Voltmeter & Ammeter ?

Last Answer : Voltmeter measures the voltage of any load or any line and the voltmeter has to be connected parallel to the load. The ammeter measures the current flowing through a load or the current of an electrical line. The ammeter is connected in series with the load.

What are the physical quantities measured with voltmeter and ammeter ?

Description : What are the physical quantities measured with voltmeter and ammeter ?

Last Answer : : The voltage difference between two points of a circuit is measured with a voltmeter. And the flow rate of an electric circuit is measured with an ammeter.

How to connect voltmeter and ammeter to circuit ?

Description : How to connect voltmeter and ammeter to circuit ?

Last Answer : : A voltmeter is connected in parallel with the two points of voltage circuit to measure the voltage difference. Again, to measure the flow rate of an electric circuit, ammeters are added to the electromagnetic circuit.

A milli voltmeter of 25 milli volt range is to be converted into an ammeter of 25 ampere range. The value (in ohm) of necessary shunt will be

Description : A milli voltmeter of 25 milli volt range is to be converted into an ammeter of 25 ampere range. The value (in ohm) of necessary shunt will be

Last Answer : A milli voltmeter of 25 milli volt range is to be converted into an ammeter of 25 ampere range. The value (in ohm) ... 001` B. `0.01` C. 1 D. `0.05`

In the circuit shown here, the readings of the ammeter and voltmeter are

Description : In the circuit shown here, the readings of the ammeter and voltmeter are

Last Answer : In the circuit shown here, the readings of the ammeter and voltmeter are A. 6 A, 60 V B. `0.6` A, 6 V C. 6 A, 6 V D. 6/11 A, 6/11 V

By mistake, a voltmeter is connected in series and an ammeter is connected in parallel, with a resistance in an electrical circuit. What will happen t

Description : By mistake, a voltmeter is connected in series and an ammeter is connected in parallel, with a resistance in an electrical circuit. What will happen t

Last Answer : By mistake, a voltmeter is connected in series and an ammeter is connected in parallel, with a ... be damaged D. Only the voltmeter will be damaged

Conversion of heat into electrical er is achieved by using – (1) Ammeter (2) Hydrometer (3) Voltmeter (4) Thermocouple

Description : Conversion of heat into electrical er is achieved by using – (1) Ammeter (2) Hydrometer (3) Voltmeter (4) Thermocouple

Last Answer : (4) Thermocouple Explanation: Thermoelectric generators convert thermal energy into electricity by using heat from the body - or any object with a temperature gradient - as their energy source. ... energy into electricity. Bismuth telluride and its alloys are commonly used in thermocouples.

Conductor resistance may be INDIRECTLY measured by using a/an _____________. A. voltmeter only B. ammeter only C. voltmeter and an ammeter D. ohmmeter only

Description : Conductor resistance may be INDIRECTLY measured by using a/an _____________. A. voltmeter only B. ammeter only C. voltmeter and an ammeter D. ohmmeter only

Last Answer : Answer: C

A multimeter may be damaged by taking a _____________. A. voltage reading while in the ammeter mode B. current reading while in the voltmeter mode C. resistance reading while in the ammeter mode D. resistance reading while in the voltmeter mode

Description : A multimeter may be damaged by taking a _____________. A. voltage reading while in the ammeter mode B. current reading while in the voltmeter mode C. resistance reading while in the ammeter mode D. resistance reading while in the voltmeter mode

Last Answer : Answer: A

You are calibrating a multimeter using internal batteries to supply power for resistance measurements. However, you are unable to adjust the pointer to 'zero' using the adjustment knob. Therefore, you should _____________. A. replace the batteries in the instrument B. measure resistance by dividing the voltmeter indication by the ammeter indication C. set the pointer using a bridge D. change scales to the R X 100 scale and adjust using the 'zero ohms' adjusting knob

Description : You are calibrating a multimeter using internal batteries to supply power for resistance measurements. However, you are unable to adjust the pointer to 'zero' using the adjustment knob. Therefore, you should ... change scales to the R X 100 scale and adjust using the 'zero ohms' adjusting knob

Last Answer : Answer: A

The RPM of an AC generator can be measured with a/an _____________. A. ammeter B. voltmeter C. vibrating reed meter D. synchroscope

Description : The RPM of an AC generator can be measured with a/an _____________. A. ammeter B. voltmeter C. vibrating reed meter D. synchroscope

Last Answer : Answer: C

Which of the instruments listed could be use to locate a grounded field coil in a synchronous motor? A. Ammeter B. Voltmeter C. Megohmmeter D. Frequency meter

Description : Which of the instruments listed could be use to locate a grounded field coil in a synchronous motor? A. Ammeter B. Voltmeter C. Megohmmeter D. Frequency meter

Last Answer : Answer: C

A useful instrument for checking A.C. motor performance by measuring possible unbalanced currents is the _____________. A. hand or battery-operated megger B. vibrating-reed frequency meter C. hook-on voltmeter-ammeter D. D'Arsonval iron-vane probe

Description : A useful instrument for checking A.C. motor performance by measuring possible unbalanced currents is the _____________. A. hand or battery-operated megger B. vibrating-reed frequency meter C. hook-on voltmeter-ammeter D. D'Arsonval iron-vane probe

Last Answer : Answer: C

Which of the following meters uses a shunt connected in series with the load, but parallel with the meter movement? A. voltmeter B. power factor meter C. wattmeter D. ammeter

Description : Which of the following meters uses a shunt connected in series with the load, but parallel with the meter movement? A. voltmeter B. power factor meter C. wattmeter D. ammeter

Last Answer : Answer: D

To determine the state of charge of a nickel-cadmium battery, you would use a/an _____________. A. voltmeter B. hydrometer C. ammeter D. potentiometer

Description : To determine the state of charge of a nickel-cadmium battery, you would use a/an _____________. A. voltmeter B. hydrometer C. ammeter D. potentiometer

Last Answer : Answer: A

Which of the listed meters uses a shunt connected in series with the load, but parallel with the meter movement? A. Voltmeter B. Power factor meter C. Ammeter D. Wattmeter

Description : Which of the listed meters uses a shunt connected in series with the load, but parallel with the meter movement? A. Voltmeter B. Power factor meter C. Ammeter D. Wattmeter

Last Answer : Answer: C

Which of the instruments listed should always be connected in series with a circuit? A. Ammeter B. Megohmmeter C. Wattmeter D. Voltmeter

Description : Which of the instruments listed should always be connected in series with a circuit? A. Ammeter B. Megohmmeter C. Wattmeter D. Voltmeter

Last Answer : Answer: A

A switchboard, for a AC electrical distribution system, will be provided with which of the following components? A. Frequency meter. B. Ammeter C. Voltmeter D. All of the above

Description : A switchboard, for a AC electrical distribution system, will be provided with which of the following components? A. Frequency meter. B. Ammeter C. Voltmeter D. All of the above

Last Answer : Answer: D

To test the state of charge of a nickel-cadmium battery, you should use a/an ____________. A. ammeter B. voltmeter C. hydrometer D. potentiometer

Description : To test the state of charge of a nickel-cadmium battery, you should use a/an ____________. A. ammeter B. voltmeter C. hydrometer D. potentiometer

Last Answer : Answer: B

A resistance in a circuit of unknown value is to be tested using the voltmeter/ammeter method. Therefore, the meters should be connected with _____________. A. both meters in series with the resistance B. both meters in parallel with the resistance C. the ammeter in series and the voltmeter in parallel with the resistance D. the ammeter in parallel and the voltmeter in series with the resistance

Description : A resistance in a circuit of unknown value is to be tested using the voltmeter/ammeter method. Therefore, the meters should be connected with _____________. A. both meters in series with the ... parallel with the resistance D. the ammeter in parallel and the voltmeter in series with the resistance

Last Answer : Answer: C

Suppose the ammeter or voltmeter you are using in the Ohm’s law experiment does not have +ve and –ve terminal markings. How will you use such ammeter or voltmeter in the circuit?

Description : Suppose the ammeter or voltmeter you are using in the Ohm’s law experiment does not have +ve and –ve terminal markings. How will you use such ammeter or voltmeter in the circuit?

Last Answer : Answer. We will use a typical battery to determine this. Connect them with wire and the battery if their readings are positive then we have connected them correctly and if their readings in negative then we have connected in opposite polarity.

Electric current is measured by (1) Voltmeter (2) Anemometer (3) Commutator (4) Ammeter

Description : Electric current is measured by (1) Voltmeter (2) Anemometer (3) Commutator (4) Ammeter

Last Answer : (4) Ammeter

Desirable resistance of a ________ is achieved by connecting a high resistance Rh in series with a galvanometer a) Ammeter b) Ohmmeter c) LED d) Voltmeter

Description : Desirable resistance of a ________ is achieved by connecting a high resistance Rh in series with a galvanometer a) Ammeter b) Ohmmeter c) LED d) Voltmeter

Last Answer : d) Voltmeter

Instrument used to find the source of seismic waves is known as a) seismometer b) voltmeter c) galvanometer d) ammeter

Description : Instrument used to find the source of seismic waves is known as a) seismometer b) voltmeter c) galvanometer d) ammeter

Last Answer : a) seismometer

State any four precautions to be taken while using an Ammeter and Voltmeter.

Description : State any four precautions to be taken while using an Ammeter and Voltmeter. 

Last Answer : Precautions to be taken while using Ammeters: Ammeters are to be connected in series of circuits. 1. While connecting ammeters across emf source always a series resistance should be used. This ... first &then range should be decreased. 4. Loading effect can be minimized by using high sensitivity

Which of the following instruments should never have their test leads connected directly to a wall outlet: w) ammeter x) voltmeter y) oscilloscope z) frequency counter

Description : Which of the following instruments should never have their test leads connected directly to a wall outlet: w) ammeter x) voltmeter y) oscilloscope z) frequency counter

Last Answer : ANSWER: W -- AMMETER