The deformation per unit length is called (a) Strain (b) Stress (c) Elasticity (d) None of these

The deformation per unit length is called
(a) Strain
(b) Stress
(c) Elasticity
(d) None of these
by

1 Answer

Answer :

(a) Strain
by

Related questions

Bulk modulus of elasticity is a. Tensile stress / Tensile strain b. Shear stress / Shear strain c. Tensile stress / Shear strain d. Normal stress on each face of cube / Volumetric strain

Description : Bulk modulus of elasticity is a. Tensile stress / Tensile strain b. Shear stress / Shear strain c. Tensile stress / Shear strain d. Normal stress on each face of cube / Volumetric strain

Last Answer : d. Normal stress on each face of cube / Volumetric strain

Young’s Modulus of elasticity is (a)Tensile stress / Tensile strain (b)Shear stress / Shear strain (c)Tensile stress / Shear strain (d)Shear stress / Tensile strain

Description : Young’s Modulus of elasticity is (a)Tensile stress / Tensile strain (b)Shear stress / Shear strain (c)Tensile stress / Shear strain (d)Shear stress / Tensile strain

Last Answer : a)Tensile stress / Tensile strain

The deformation of a solid when stress is applied is called a) Strain b) Elasticity c) Rigidity d) Pressure

Description : The deformation of a solid when stress is applied is called a) Strain b) Elasticity c) Rigidity d) Pressure

Last Answer : a) Strain

Resilience of spring is (a) Strain energy per unit length (b) Strain energy per unit area (c) Strain energy per unit mass (d) None

Description : Resilience of spring is (a) Strain energy per unit length (b) Strain energy per unit area (c) Strain energy per unit mass (d) None

Last Answer : (d) None

The ratio of lateral strain to linear strain is called (a) Modulus of Elasticity (b) Modulus of Rigidity (c) Bulk Modulus (d) Poisson’s Ratio

Description : The ratio of lateral strain to linear strain is called (a) Modulus of Elasticity (b) Modulus of Rigidity (c) Bulk Modulus (d) Poisson’s Ratio

Last Answer : (d) Poisson’s Ratio

Shear stress causes (a) Deformation (b) Distortion (c) Deformation as well as distortion (d) None

Description : Shear stress causes (a) Deformation (b) Distortion (c) Deformation as well as distortion (d) None

Last Answer : b) Distortion

Shear stress causes (a) Deformation (b) Distortion (c) Displacement (d) None

Description : Shear stress causes (a) Deformation (b) Distortion (c) Displacement (d) None

Last Answer : (b) Distortion

Shear stress causes (a) Deformation (b)Elongation (c) Contraction (d) None

Description : Shear stress causes (a) Deformation (b)Elongation (c) Contraction (d) None

Last Answer : (d) None

When a bar is subjected to increase in temperature and its deformation is prevented, the stress induced in the bar is (a) Tensile (b) Compressive (c) Shear (d) None of the above

Description : When a bar is subjected to increase in temperature and its deformation is prevented, the stress induced in the bar is (a) Tensile (b) Compressive (c) Shear (d) None of the above

Last Answer : (b) Compressive

When a bar is subjected to a change of temperature and its longitudinal deformation is prevented, the stress induced in the bar is (a) Tensile (b) Compressive (c) Shear (d) Temperature

Description : When a bar is subjected to a change of temperature and its longitudinal deformation is prevented, the stress induced in the bar is (a) Tensile (b) Compressive (c) Shear (d) Temperature

Last Answer : (d) Temperature

The graphical representation of variation of axial load on y axis and position of cross section along x axis is called as _____ (a) Bending moment diagram (b) Shear force diagram (c) Stress-strain diagram (d) Trust diagram

Description : The graphical representation of variation of axial load on y axis and position of cross section along x axis is called as _____ (a) Bending moment diagram (b) Shear force diagram (c) Stress-strain diagram (d) Trust diagram

Last Answer : (d) Trust diagram

In a simple bending theory, one of the assumption is that the plane sections before bending remain plane after bending. This assumption means that a. stress is uniform throughout the beam b. strain is uniform throughout the beam c. stress is proportional to the distance from the neutral axis d. strain is proportional to the distance from the neutral axis

Description : In a simple bending theory, one of the assumption is that the plane sections before bending remain plane after bending. This assumption means that a. stress is uniform throughout the beam b. ... the distance from the neutral axis d. strain is proportional to the distance from the neutral axis

Last Answer : d. strain is proportional to the distance from the neutral axis

Which stress strain curve is more steep (a) For a ductile material (b) For a brittle material (c) For a pure metal (d) None

Description : Which stress strain curve is more steep (a) For a ductile material (b) For a brittle material (c) For a pure metal (d) None

Last Answer : b) For a brittle material

Linear stress strain curve is for a (a) Load ∞ displacement (b) Load ∞ ( 1/displacement) (c) Load = ( displacement)2 (d) None

Description : Linear stress strain curve is for a (a) Load ∞ displacement (b) Load ∞ ( 1/displacement) (c) Load = ( displacement)2 (d) None

Last Answer : (a) Load ∞ displacement

In a composite body, consisting of two different materials...........will be same in both materials. (a) Stress (b) Strain (c) Both stress and strain (d) None of these

Description : In a composite body, consisting of two different materials...........will be same in both materials. (a) Stress (b) Strain (c) Both stress and strain (d) None of these

Last Answer : (b) Strain

The statement : stress is proportional to strain, i.e. the Hooke’s law holds good upto (a) Elastic Limit (b) Proportional Limit (c) Plastic Limit (d) Yield point

Description : The statement : stress is proportional to strain, i.e. the Hooke’s law holds good upto (a) Elastic Limit (b) Proportional Limit (c) Plastic Limit (d) Yield point

Last Answer : (b) Proportional Limit

Which of the following is a dimensionless quantity? (a) Shear stress (b) Poison’s ratio (c) Strain (d) Both (b) and (c)

Description : Which of the following is a dimensionless quantity? (a) Shear stress (b) Poison’s ratio (c) Strain (d) Both (b) and (c)

Last Answer : (d) Both (b) and (c)

Modulus of rigidity is (a)Tensile stress / Tensile strain (a)Shear stress / Shear strain (a)Tensile stress / Shear strain (a)Shear stress / Tensile strain

Description : Modulus of rigidity is (a)Tensile stress / Tensile strain (a)Shear stress / Shear strain (a)Tensile stress / Shear strain (a)Shear stress / Tensile strain

Last Answer : (a)Shear stress / Shear strain

Stiffness of material is measured by, A. Proportional unit B. Modules of elasticity C. Stress/ strain

Description : Stiffness of material is measured by, A. Proportional unit B. Modules of elasticity C. Stress/ strain

Last Answer : B. Modules of elasticity

A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the leaves are 100mm and 12mm respectively. If modulus of elasticity is 207000N/mm², calculate the initial nip. (a) 26.8mm (b) 24.9mm (c) 22.5mm (d)23.1mm

Description : A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the ... /mm², calculate the initial nip. (a) 26.8mm (b) 24.9mm (c) 22.5mm (d)23.1mm

Last Answer : b) 24.9mm

Elongation of a bar of uniform cross section of length ‘L’, due to its own weight ‘W’ is given by a. 2WL/E b. WL/E c. WL/2E d. WL/3E Where, E=Young’s modulus of elasticity of material

Description : Elongation of a bar of uniform cross section of length ‘L’, due to its own weight ‘W’ is given by a. 2WL/E b. WL/E c. WL/2E d. WL/3E Where, E=Young’s modulus of elasticity of material

Last Answer : c. WL/2E

18.The total extension of a taper rod of length ‘L’ and end diameters ‘D1’ and ‘D2’, subjected to a load (P), is given of a. 4PL/ΠE. D1D2 b. 3PL/ΠE. D1D2 c. 2PL/ΠE. D1D2 d. PL/ΠE.D1D2 Where E=Young’s modulus of elasticity

Description : 18.The total extension of a taper rod of length ‘L’ and end diameters ‘D1’ and ‘D2’, subjected to a load (P), is given of a. 4PL/ΠE. D1D2 b. 3PL/ΠE. D1D2 c. 2PL/ΠE. D1D2 d. PL/ΠE.D1D2 Where E=Young’s modulus of elasticity

Last Answer : a. 4PL/ΠE. D1D2

When a wire is stretched to double in length, the longitudinal strain produced in it is (a) 0.5 (b) 1.0 (c) 1.5 (d) 2.0

Description : When a wire is stretched to double in length, the longitudinal strain produced in it is (a) 0.5 (b) 1.0 (c) 1.5 (d) 2.0

Last Answer : b) 1.0

Pick out the correct statement. (A) Materials exhibiting high elasticity obey Hooke's law (B) The elastic behaviour of rubber under compression is the same as its behaviour under tension (C) The damping capacity of a material is due to its plastic deformation (D) The stress required to cause plastic flow in polycrystalline material is

Description : Pick out the correct statement. (A) Materials exhibiting high elasticity obey Hooke's law (B) The elastic behaviour of rubber under compression is the same as its behaviour under tension (C) ... to its plastic deformation (D) The stress required to cause plastic flow in polycrystalline material is

Last Answer : Option B

The vertical distance between the axis of the beam before and after loading at a point is called as _______ a. Deformation b. Deflection c. Slope d. None of above.

Description : The vertical distance between the axis of the beam before and after loading at a point is called as _______ a. Deformation b. Deflection c. Slope d. None of above.

Last Answer : b. Deflection

Hooke's law (A) Applies to elastic deformation (B) Applies beyond limit of proportionality in stress-strain curve (C) States that stress is inversely proportional to strain upto elastic limit (D) None of these

Description : Hooke's law (A) Applies to elastic deformation (B) Applies beyond limit of proportionality in stress-strain curve (C) States that stress is inversely proportional to strain upto elastic limit (D) None of these

Last Answer : (A) Applies to elastic deformation

Sinking of support effects the a. deflection at supports b. moments at supports c. fixity d. deformation at supports

Description : Sinking of support effects the a. deflection at supports b. moments at supports c. fixity d. deformation at supports

Last Answer : b. moments at supports

A simply supported beam carries a uniformly distributed load over the whole span.The deflection at the centre is y.If the distributed load per unit length is doubled and also depth of beam is doubled ,then the deflection at the centre would be a.2y b.4y c.y/2 d.y/4.

Description : A simply supported beam carries a uniformly distributed load over the whole span.The deflection at the centre is y.If the distributed load per unit length is doubled and also depth of beam is doubled ,then the deflection at the centre would be a.2y b.4y c.y/2 d.y/4.

Last Answer : d.y/4.

The shear force at the centre of a simply supported beam of span l carrying a uniformly distributed load of w per unit length over the whole span is (a) wl (b) wl/2 (c) wl/4 (d) Zero

Description : The shear force at the centre of a simply supported beam of span l carrying a uniformly distributed load of w per unit length over the whole span is (a) wl (b) wl/2 (c) wl/4 (d) Zero

Last Answer : (d) Zero

The deformation of a spring produced by a unit load is called (A) Stiffness (B) Flexibility (C) Influence coefficient (D) Unit strain

Description : The deformation of a spring produced by a unit load is called (A) Stiffness (B) Flexibility (C) Influence coefficient (D) Unit strain

Last Answer : (B) Flexibility

The ratio of stress to volumetric strain is called a) Shear Modulus b) Young’s Modulus c) Bulk Modulus d) Modulus of elasticity

Description : The ratio of stress to volumetric strain is called a) Shear Modulus b) Young’s Modulus c) Bulk Modulus d) Modulus of elasticity

Last Answer : c) Bulk Modulus

The ability of a body to return to its original shape is called: a) Plasticity b) Elasticity c) Strain d) Stress

Description : The ability of a body to return to its original shape is called: a) Plasticity b) Elasticity c) Strain d) Stress

Last Answer : b) Elasticity

The property of a material by which it can be drawn to a smaller section by applying a tensile load is called (a) Elasticity (b) Plasticity (c) Ductility (d) Malleability

Description : The property of a material by which it can be drawn to a smaller section by applying a tensile load is called (a) Elasticity (b) Plasticity (c) Ductility (d) Malleabilityy

Last Answer : (c) Ductility

The property of a material by which it can be beaten or rolled into thin sheets, is called (a) Elasticity (b) Plasticity (c) Ductility (d) Malleability

Description : The property of a material by which it can be beaten or rolled into thin sheets, is called (a) Elasticity (b) Plasticity (c) Ductility (d) Malleability

Last Answer : (d) Malleability

The ability of the material to deform without breaking is called (a) Elasticity (b) Plasticity (c) Creep (d) None of these

Description : The ability of the material to deform without breaking is called (a) Elasticity (b) Plasticity (c) Creep (d) None of these

Last Answer : (b) Plasticity

What is the maximum value of deforming force upto which a material shows elastic property and above which the material loses it? (1) Elasticity (2) Strain (3) Elastic Limit (4) Stress

Description : What is the maximum value of deforming force upto which a material shows elastic property and above which the material loses it? (1) Elasticity (2) Strain (3) Elastic Limit (4) Stress

Last Answer : (3) Elastic Limit Explanation: The Maximum Extent to which a solid may be stretched without permanent alteration of size or shape.

What is the maximum value of deforming force up to which a material shows elastic property and above which the material loses it? (1) Elasticity (2) Strain (3) Elastic Limit (4) Stress

Description : What is the maximum value of deforming force up to which a material shows elastic property and above which the material loses it? (1) Elasticity (2) Strain (3) Elastic Limit (4) Stress

Last Answer : (4) Elastic Limit Explanation: The Maximum Extent to which a solid may be stretched without permanent alteration of size or shape.

The ratio of shear stress and shear strain of an elastic material, is (A) Modulus of Rigidity (B) Shear Modulus (C) Modulus of Elasticity (D) Both (a) and (b)

Description : The ratio of shear stress and shear strain of an elastic material, is  (A) Modulus of Rigidity  (B) Shear Modulus  (C) Modulus of Elasticity  (D) Both (a) and (b) 

Last Answer : (D) Both (a) and (b) 

Modulus of elasticity is defined as: A. The stress at the proportional limit B. The stress-strain ratio within the proportional limit

Description : Modulus of elasticity is defined as: A. The stress at the proportional limit B. The stress-strain ratio within the proportional limit

Last Answer : B. The stress-strain ratio within the proportional limit

The ratio of stress to strain i: a) Modulus of conductivity b) Modules of Elasticity c) Modulus of electricity d) Modulus of Viscosity

Description : The ratio of stress to strain i: a) Modulus of conductivity b) Modules of Elasticity c) Modulus of electricity d) Modulus of Viscosity

Last Answer : b) Modules of Elasticity

The Modulus of Elasticity for a material refers to: w) the ability of a material to resist corrosion x) the ratio of stress over strain y) the maximum load over the cross sectional area z) none of the above

Description : The Modulus of Elasticity for a material refers to: w) the ability of a material to resist corrosion x) the ratio of stress over strain y) the maximum load over the cross sectional area z) none of the above

Last Answer : ANSWER: X -- THE RATIO OF STRESS OVER STRAIN

A circular shaft subjected to torsion undergoes a twist of 10in a length of 120 cm. If the maximum shear stress induced is limited to 1000 kg/cm2and if modulus of rigidity G = 0.8 x 106then the radius of the shaft should be (a) p/8 (b) p/27 (c) 18/p (d) 27/p

Description : A circular shaft subjected to torsion undergoes a twist of 10in a length of 120 cm. If the maximum shear stress induced is limited to 1000 kg/cm2and if modulus of rigidity G = 0.8 x 106then the radius of the shaft should be (a) p/8 (b) p/27 (c) 18/p (d) 27/p

Last Answer : (d) 27/p

Unit stress after load application is based on (a) Original area of cross section (b) Changing area of cross section (c) Final area of cross section under maximum load (d) None

Description : Unit stress after load application is based on (a) Original area of cross section (b) Changing area of cross section (c) Final area of cross section under maximum load (d) None

Last Answer : (a) Original area of cross section

In the relation ( T/J = Gθ/L = τ/ R), the letter G denotes modulus of ______ a. elasticity b. plasticity c. rigidity d. resilience

Description : In the relation ( T/J = Gθ/L = τ/ R), the letter G denotes modulus of ______ a. elasticity b. plasticity c. rigidity d. resilience

Last Answer : c. rigidity

The property of the material which allows it to be drawn into smaller section (a) Plasticity (b) Ductility (c) Elasticity (d) Malleability

Description : The property of the material which allows it to be drawn into smaller section (a) Plasticity (b) Ductility (c) Elasticity (d) Malleability

Last Answer : (b) Ductility

Most important features of any spring are (a) Deflection, stiffness and strength (b) Stiffness, bending and shear strengths (c) Strain energy, deflection and strength (d) None

Description : Most important features of any spring are (a) Deflection, stiffness and strength (b) Stiffness, bending and shear strengths (c) Strain energy, deflection and strength (d) None

Last Answer : (c) Strain energy, deflection and strength

The strain energy stored in a spiral spring is given by? (a) 12M²L/Ebtᵌ (b) 6M²L/Ebtᵌ (c) 8M²L/Ebtᵌ (d) None of the listed

Description : The strain energy stored in a spiral spring is given by? (a) 12M²L/Ebtᵌ (b) 6M²L/Ebtᵌ (c) 8M²L/Ebtᵌ (d) None of the listed

Last Answer : (b) 6M²L/Ebtᵌ

The springs in brakes and clutches are used (a) To apply forces (b) To measure forces (c) To absorb shocks (d) To absorb strain energy

Description : The springs in brakes and clutches are used (a) To apply forces (b) To measure forces (c) To absorb shocks (d) To absorb strain energy

Last Answer : (a) To apply forces

In spring balances, the spring is used (a) To apply forces (b) To absorb shocks (c) To store strain energy (d) To measure forces

Description : In spring balances, the spring is used (a) To apply forces (b) To absorb shocks (c) To store strain energy (d) To measure forces

Last Answer : (d) To measure forces

Strain energy in a spring should be (a) Large (b) Small (c) Zero (d) None

Description : Strain energy in a spring should be (a) Large (b) Small (c) Zero (d) None

Last Answer : (a) Large