Description : Linear stress strain curve is for a (a) Load ∞ displacement (b) Load ∞ ( 1/displacement) (c) Load = ( displacement)2 (d) None
Last Answer : (a) Load ∞ displacement
Description : In which of the following case stress concentration factor is ignored? a) Ductile material under static load b) Ductile material under fluctuating load c) Brittle material under static load
Last Answer : a) Ductile material under static load
Description : Maximum total strain energy theory is applicable to (a) Ductile materials (b) Brittle materials (c) Composite materials (d) None
Last Answer : (a) Ductile materials
Last Answer : (b) Brittle materials
Description : Maximum principal strain theory is applicable to (a) Ductile materials (b) Brittle materials (c) Composite materials (d) None
Description : A ductile material may not meet a failure if it has been tested for the theories of failure (a) Firstly Maximum Shear Stress Theory (b) Secondly Maximum Shear Strain Energy Theory (c) Both (a) & (b) (d) None
Last Answer : (c) Both (a) & (b)
Description : A power transmitting ductile material shaft under P, T and M will be designed on the basis of (a) Rankine theory (b) Guest Theory (c) Haigh theory (d) None
Last Answer : (b) Guest Theory
Description : A power transmitting ductile material shaft under P, T and M will fail under (a) Tensile considerations only (b) Compressive considerations only (c) Shear considerations only (d) None
Last Answer : (c) Shear considerations only
Description : Which of the following theories of failure is most appropriate for a brittle material? (a) Maximum principal strain theory (b) Maximum principal stress theory (c) Maximum shear stress theory (d) Maximum strain energy theory
Last Answer : (b) Maximum principal stress theory
Description : A brittle material has (a) No elastic zone (b) No plastic zone (c) Large plastic zone (d) None of these
Last Answer : 2
Description : Maximum shear stress theory is applicable to (a) Ductile materials (b) Brittle materials (c) Composite materials
Description : Maximum principal stress theory is applicable to (a) Ductile materials (b) Brittle materials (c) Composite materials (d) None
Description : In a simple bending theory, one of the assumption is that the plane sections before bending remain plane after bending. This assumption means that a. stress is uniform throughout the beam b. ... the distance from the neutral axis d. strain is proportional to the distance from the neutral axis
Last Answer : d. strain is proportional to the distance from the neutral axis
Description : The graphical representation of variation of axial load on y axis and position of cross section along x axis is called as _____ (a) Bending moment diagram (b) Shear force diagram (c) Stress-strain diagram (d) Trust diagram
Last Answer : (d) Trust diagram
Description : In a composite body, consisting of two different materials...........will be same in both materials. (a) Stress (b) Strain (c) Both stress and strain (d) None of these
Last Answer : (b) Strain
Description : The statement : stress is proportional to strain, i.e. the Hooke’s law holds good upto (a) Elastic Limit (b) Proportional Limit (c) Plastic Limit (d) Yield point
Last Answer : (b) Proportional Limit
Description : Which of the following is a dimensionless quantity? (a) Shear stress (b) Poison’s ratio (c) Strain (d) Both (b) and (c)
Last Answer : (d) Both (b) and (c)
Description : The deformation per unit length is called (a) Strain (b) Stress (c) Elasticity (d) None of these
Last Answer : (a) Strain
Description : Bulk modulus of elasticity is a. Tensile stress / Tensile strain b. Shear stress / Shear strain c. Tensile stress / Shear strain d. Normal stress on each face of cube / Volumetric strain
Last Answer : d. Normal stress on each face of cube / Volumetric strain
Description : Modulus of rigidity is (a)Tensile stress / Tensile strain (a)Shear stress / Shear strain (a)Tensile stress / Shear strain (a)Shear stress / Tensile strain
Last Answer : (a)Shear stress / Shear strain
Description : Young’s Modulus of elasticity is (a)Tensile stress / Tensile strain (b)Shear stress / Shear strain (c)Tensile stress / Shear strain (d)Shear stress / Tensile strain
Last Answer : a)Tensile stress / Tensile strain
Description : A material capable of undergoing large permanent deformation, when subjected to compression is termed as (A) Malleable (B) Ductile (C) Brittle (D) None of these
Last Answer : (A) Malleable
Description : Cast iron is a __________ material. (A) Brittle (B) Ductile (C) Tough (D) Malleable
Last Answer : (A) Brittle
Description : . A material capable of undergoing large permanent deformation, when subjected to tension is termed as (A) Friable (B) Ductile (C) Brittle (D) None of these
Last Answer : (B) Ductile
Description : Pick up the correct statement from the following: (A) A ductile material has large plastic zone (B) A brittle material has no plastic zone (C) A rigid material has no plastic zone (D) All the above
Last Answer : All the above
Description : __________ test is the appropriate test to determine whether a material is ductile or brittle. (A) Impact (B) Cupping (C) Hardness (D) Tensile
Last Answer : (A) Impact
Description : A dense structure of grinding wheel is not used for the (A) Ductile material (B) Hard materials (C) Brittle materials (D) Finishing cuts
Last Answer : A) Ductile material
Description : The material in which large deformation is possible before absolute failure by rupture takes place, is known as (a) Ductile (b) Plastic (c) Brittle (d) Elastic
Last Answer : Ductile
Description : Define factor of safety for ductile and brittle material.
Last Answer : Factor of safety for ductile material: It is defined as ratio of yield stress to the working stress or Factor of safety for Brittle material : It is defined as ratio of ultimate stress to the working stress /permissible /design stress or
Description : When the shaft is subjected to pure torsional moment, the torsional stress is given by? a) None of the listed b) 32M/πdᵌ c) 16M/πdᵌ d) 8M/πdᵌ
Last Answer : c) 16M/πdᵌ
Description : When the shaft is subjected to pure bending moment, the bending stress is given by? a) None of the listed b) 32M/πdᵌ c) 16M/πdᵌ d) 8M/πdᵌ
Last Answer : b) 32M/πdᵌ
Description : The design of shafts made of brittle materials is based on (a) Guest’s theory (b) Rankine’s theory (c) St. Venant’s theory (d) Von Mises Theory
Last Answer : (b) Rankine’s theory
Description : A ductile material may not meet a failure if it has been tested for the theories of failure (a) Firstly Maximum Principal Theory (b) Secondly Maximum Principal Strain Theory (c) Thirdly Maximum principal strain energy theory (d) None
Last Answer : (d) None
Description : The area under stress-strain curve represents a.Hardness of material b.Breaking strength of the material c.Energy required to cause failure d.Toughness of material e.Malleabbility of material
Last Answer : c. Energy required to cause failure
Description : Which of the following assumptions are made in torsion theory? a. Shaft is perfectly straight b. Material of the shaft is heterogeneous c. Twist cannot be uniform along the length of the shaft d. Shaft is perfectly curve v
Last Answer : a. Shaft is perfectly straight b. Material of the shaft is heterogeneous
Description : A water main 1 m in diameter contains a fluid having pressure 1 N/mm2. If the maximum permissible tensile stress in the metal is 20 N/mm2, th thickness of the metal required would be a) 2 cm b) 2.5cm c) 1 cm d) 0.5 cm
Last Answer : b) 2.5cm
Description : The stress at which extension of a material takes place more quickly as compared to increase in load, is called (a) No elastic zone (b) Plastic point (c) Yield point (d) Breaking point
Last Answer : (c) Yield point
Description : 'Shock-absorbers are usually made of steel as it – (1) is not brittle (2) has lower elasticity (3) has higher elasticity (4) has no ductile property
Last Answer : (3) has higher elasticity Explanation: A shock absorber is a mechanical device designed to smooth out or damp shock impulse, and dissipate kinetic energy. Steel is an alloy made by combining iron and other elements, the most common of these being carbon.
Description : Which theories of failure are used for (a) ductile materials, and (B) brittle materials ?
Last Answer : For ductile materials, theories of failure used are maximum shear stress theory, and maximum energy of distortion theory; while for brittle materials, theory of maximum principal stress, and maximum strain are used.
Description : List at least two factors that promote transition from ductile to brittle fracture.
Last Answer : Manner of loading, and the rate of loading promote transition from ductile to brittle frac¬ture. A machine member may have ductile failure under static loading but may fail in brittle fashion when the ... testing speed but if load is applied at a high velocity then failure may be brittle.
Description : Polystyrene is a __________ plastic at room temperature. (A) Ductile (B) Brittle (C) Malleable (D) None of these
Last Answer : (B) Brittle
Description : Zinc is highly __________ at room temperature. (A) Ductile (B) Resistant to atmospheric corrosion (C) Malleable (D) Brittle
Last Answer : (B) Resistant to atmospheric corrosion
Description : Substances that elongate considerably and undergo plastic deformation before they break are known as A. brittle substances B. breakable substances C. ductile substances D. elastic substances
Last Answer : ductile substances
Description : Steel produced from phosphatic iron is __________ in nature. (A) Malleable (B) Ductile (C) Brittle (D) Tough
Last Answer : (C) Brittle
Description : The 'transition temperature' for ductile to brittle behaviour of steel increases with increase in the __________ content in steel. (A) Carbon (B) Manganese (C) Both 'a' nor 'b' (D) Neither 'a' nor 'b'
Last Answer : (A) Carbon
Description : The materials which fracture even at small strains are termed as brittle, while those materials which exhibit an appreciable deformation before failure are termed as (A) Rigid (B) Tough (C) Ductile (D) Plastic
Last Answer : Option C
Description : What Is Ductile-brittle Transition Temperature?
Last Answer : It is the temperature below which the tendency of a material to fracture increases rather than forming. Below this temperature the material loses its ductility. It is also called Nil Ductility Temperature
Description : Which Theories Of Failure Are Used For? (a) Ductile Materials (b) Brittle Materials?
Last Answer : For ductile materials, theories of failure used are maximum shear stress theory and maximum energy of distortion theory; For brittle materials, the theory of maximum principal stress and maximum strain are used.
Description : List At Least Two Factors That Promote The Transition From Ductile To Brittle Fracture?
Last Answer : The manner of loading and the rate of loading promote the transition from ductile to brittle fracture. A machine member may have ductile failure under static loading but may fail in brittle fashion when the ... testing speed, but if the load is applied at a high velocity then failure may be brittle.
Description : Distinguish Between Brittle Fracture And Ductile Fracture?
Last Answer : In brittle fracture, crack growth is up to a small depth of the material. In ductile fracture large amount of plastic deformation is present to a higher depth.