In shafts with keyways the allowable stresses are usually ------------ proportional to the twisting moment. a.25% b. 50% c. 75% d. 95%

In shafts with keyways the allowable stresses are usually ------------ proportional to the twisting moment.
a.25%
b. 50%
c. 75%
d. 95%
by

1 Answer

Answer :

c. 75%
by
by
What is answer

Related questions

Two shafts will have equal strength, if (a) diameter of both the shafts is same (b) angle of twist of both the shafts is same (c) material of both the shafts is same (d) twisting moment of both the shafts is same

Description : Two shafts will have equal strength, if (a) diameter of both the shafts is same (b) angle of twist of both the shafts is same (c) material of both the shafts is same (d) twisting moment of both the shafts is same

Last Answer : d) twisting moment of both the shafts is same

The angle of twist is ------------- proportional to the twisting moment. a. directly. b. inversely. c. indirectly. d. reversely.

Description : The angle of twist is ------------- proportional to the twisting moment. a. directly. b. inversely. c. indirectly. d. reversely.

Last Answer : a. directly.

It is a secondary shaft used to counter the direction of main shaft. 81. Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) twisting

Description : It is a secondary shaft used to counter the direction of main shaft. 81. Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) twisting

Last Answer : b) Tensile

When two transformers are operating in parallel, they will share the load as under: (A) proportional to their impedances. (B) inversely proportional to their impedances. (C) 50% - 50% (D) 25%-75%

Description : When two transformers are operating in parallel, they will share the load as under: (A) proportional to their impedances. (B) inversely proportional to their impedances. (C) 50% - 50% (D) 25%-75%

Last Answer : Ans: A High rating transformer has higher impedance. kVA rating α Impedance of transformer

Ratio of diameters of two shafts joined in series is 2. If the two shafts have the same material and the same length the ratio of their shear stresses is a. 2 b. 4 c. 8 d. 16

Description : Ratio of diameters of two shafts joined in series is 2. If the two shafts have the same material and the same length the ratio of their shear stresses is a. 2 b. 4 c. 8 d. 16

Last Answer : c. 8

Hollow shafts can be made as strong as solid shafts by making the twisting moments of both the shafts same. Shafts made by __________ have residual stresses. (A) Forging (B) Cold rolling (C) Hot rolling (D) Casting

Description : Hollow shafts can be made as strong as solid shafts by making the twisting moments of both the shafts same. Shafts made by __________ have residual stresses. (A) Forging (B) Cold rolling (C) Hot rolling (D) Casting

Last Answer : (B) Cold rolling

Which of the following is not an assumption in derivation of torsion equation? a. Circular shaft remains circular after twisting b. Plane section of the shaft remain plane after twisting c. Material of shaft is isotropic d. Angle of twist is proportional to radius

Description : Which of the following is not an assumption in derivation of torsion equation? a. Circular shaft remains circular after twisting b. Plane section of the shaft remain plane after twisting c. Material of shaft is isotropic d. Angle of twist is proportional to radius

Last Answer : d. Angle of twist is proportional to radius

Which of the following loading is considered for the design of axles ? (a) Bending moment only (b) Twisting moment only (c) Combined bending moment and torsion (d) Combined action of bending moment, twisting moment and axial thrust

Description : Which of the following loading is considered for the design of axles ? (a) Bending moment only (b) Twisting moment only (c) Combined bending moment and torsion (d) Combined action of bending moment, twisting moment and axial thrust

Last Answer : (a) Bending moment only

The relationship among twisting moment(T) acting on a rotating shaft, power in watt(W), and angular velocity in radian per second(w) will be (a) T = W/w (b) W = Tw (c) W = T/w (d) none of these

Description : The relationship among twisting moment(T) acting on a rotating shaft, power in watt(W), and angular velocity in radian per second(w) will be (a) T = W/w (b) W = Tw (c) W = T/w (d) none of these

Last Answer : (b) W = Tw

At fully plastic twisting moment (a) only fibres at surface are stressed to yield point in shear (b) fibres at centre are stressed to yield point in shear (c) all fibres are stressed to yield point in shear (d) none of these

Description : At fully plastic twisting moment (a) only fibres at surface are stressed to yield point in shear (b) fibres at centre are stressed to yield point in shear (c) all fibres are stressed to yield point in shear (d) none of these

Last Answer : (c) all fibres are stressed to yield point in shear

A shaft of length L is subject to a constant twisting moment T along its length L, then angle q through which one end of the bar will twist relative to other will be (a) T/g (b) T/GJ (c) GJ/TL (d) TL/GJ

Description : A shaft of length L is subject to a constant twisting moment T along its length L, then angle q through which one end of the bar will twist relative to other will be (a) T/g (b) T/GJ (c) GJ/TL (d) TL/GJ

Last Answer : (d) TL/GJ

If in a bar after twisting moment T has been applied, a line on surface is moved by an angle g then shearing moment will be (a) t/g (b) g (c) g/t (d) none of these

Description : If in a bar after twisting moment T has been applied, a line on surface is moved by an angle g then shearing moment will be (a) t/g (b) g (c) g/t (d) none of these

Last Answer : (b) g

For a solid or a hollow shaft subject to a twisting moment T, the torsional shearing stress t at a distance r from the centre will be (a) t = Tr/J (b) t = Tr (c) t = TJ/r (d) none of these

Description : For a solid or a hollow shaft subject to a twisting moment T, the torsional shearing stress t at a distance r from the centre will be (a) t = Tr/J (b) t = Tr (c) t = TJ/r (d) none of these

Last Answer : (a) t = Tr/J

A member subjected to couple produces rotational motion about its longitudinal axis called as ________ a. torsion b. twisting moment c. both a. and b. d. bending moment

Description : A member subjected to couple produces rotational motion about its longitudinal axis called as ________ a. torsion b. twisting moment c. both a. and b. d. bending moment

Last Answer : c. both a. and b.

The product of the tangential force acting on the shaft and radius of shaft known as (a) Torsional rigidity (b) Flexural rigidity (c) Bending moment (d) Twisting moment

Description : The product of the tangential force acting on the shaft and radius of shaft known as (a) Torsional rigidity (b) Flexural rigidity (c) Bending moment (d) Twisting moment

Last Answer : (d) Twisting moment

When a shaft is subjected to a twisting moment, every cross-section of the shaft will be under (a) Tensile stress (b) Compressive stress (c) Shear stress (d) All of these

Description : When a shaft is subjected to a twisting moment, every cross-section of the shaft will be under (a) Tensile stress (b) Compressive stress (c) Shear stress (d) All of these

Last Answer : c) Shear stress

Strength of a shaft a. Is equal to maximum shear stress in the shaft at the time of elastic failure b. Is equal to maximum shear stress in the shaft at the time of rupture c. Is equal to torsional rigidity d. Is ability to resist maximum twisting moment

Description : Strength of a shaft a. Is equal to maximum shear stress in the shaft at the time of elastic failure b. Is equal to maximum shear stress in the shaft at the time of rupture c. Is equal to torsional rigidity d. Is ability to resist maximum twisting moment

Last Answer : d. Is ability to resist maximum twisting moment

A beam is a structural member which is subjected to (a) Axial tension or compression (b) Transverse loads and couples (c) Twisting moment (d) No load, but its axis should be horizontal and x-section rectangular or circular

Description : A beam is a structural member which is subjected to (a) Axial tension or compression (b) Transverse loads and couples (c) Twisting moment (d) No load, but its axis should be horizontal and x-section rectangular or circular

Last Answer : b) Transverse loads and couples

What is the product of sectional modulus and allowable bending stress called as? a. Moment of inertia b. Moment of rigidity c. Moment of resistance d. Radius of gyration

Description : What is the product of sectional modulus and allowable bending stress called as? a. Moment of inertia b. Moment of rigidity c. Moment of resistance d. Radius of gyration

Last Answer : c. Moment of resistance

Flexible shafts have ______ rigidity in bending moment. a) High b) Low c) Very high d) Extremely low

Description : Flexible shafts have ______ rigidity in bending moment. a) High b) Low c) Very high d) Extremely low

Last Answer : b) Low

Which of the following act on shafts? a) Torsional moment b) Bending Moment c) Both torsional and bending d) None of the mentioned

Description : Which of the following act on shafts? a) Torsional moment b) Bending Moment c) Both torsional and bending d) None of the mentioned

Last Answer : c) Both torsional and bending

According to the World Bank, during the period 1996 to 2000, the approximate percentage loss of gross domestic produce due to disasters was? a. 2.85% b. 2.25% c. 2.50% d.1.95%

Description : According to the World Bank, during the period 1996 to 2000, the approximate percentage loss of gross domestic produce due to disasters was? a. 2.85% b. 2.25% c. 2.50% d.1.95%

Last Answer : b. 2.25%

If a dwarf pea plant was treated with gibberellic acid, it became as tall, as tall pea plants. If these pea plants are crossed with pure tall pea plants, what will be the phenotypic ratio in F1 generation? (a) All dwarf plants (b) 50% tall and 50% dwarf plants (c) 75% tall and 25% dwarf plants (d) 100% tall plants

Description : If a dwarf pea plant was treated with gibberellic acid, it became as tall, as tall pea plants. If these pea plants are crossed with pure tall pea plants, what will be the phenotypic ratio in F1 generation? ... (b) 50% tall and 50% dwarf plants (c) 75% tall and 25% dwarf plants (d) 100% tall plants

Last Answer : Ans. ((d))

Accumulators should have adequate volume to store refrigerant charge at least (a) 10% (b) 25% (c) 50% (d) 75%

Description : Accumulators should have adequate volume to store refrigerant charge at least (a) 10% (b) 25% (c) 50% (d) 75%

Last Answer : Ans: c

100% modulation in AM means a corresponding increase in total power by: A. 25% B. 75% C. 100% D. 50%

Description : 100% modulation in AM means a corresponding increase in total power by: A. 25% B. 75% C. 100% D. 50%

Last Answer : D. 50%

Both husband and wife have normal vision though their fathers were colour blind. The probability of their daughter becoming colour blind is (a) 0% (b) 25% (c) 50% (d) 75%.

Description : Both husband and wife have normal vision though their fathers were colour blind. The probability of their daughter becoming colour blind is (a) 0% (b) 25% (c) 50% (d) 75%.

Last Answer : (a) 0%

Albinism is known to be due to an autosomal recessive mutation. The first child of a couple with normal skin pigmentation was an albino. What is the probability that their second child will also be an albino? (a) 50% (b) 75% (c) 100% (d) 25%

Description : Albinism is known to be due to an autosomal recessive mutation. The first child of a couple with normal skin pigmentation was an albino. What is the probability that their second child will also be an albino? (a) 50% (b) 75% (c) 100% (d) 25%

Last Answer : (d) 25%

Down’s syndrome is caused by an extra copy of chromosome number 21. What percentage of offspring produced by an affected mother and a normal father would be affected by this disorder? (a) 100% (b) 75% (c) 50% (d) 25%

Description : Down’s syndrome is caused by an extra copy of chromosome number 21. What percentage of offspring produced by an affected mother and a normal father would be affected by this disorder? (a) 100% (b) 75% (c) 50% (d) 25%

Last Answer : (c) 50%

A man whose father was colour blind marries a woman who had a colour blind mother and normal father. What percentage of male children of this couple will be colour blind? (a) 25% (b) 0% (c) 50% (d) 75%

Description : A man whose father was colour blind marries a woman who had a colour blind mother and normal father. What percentage of male children of this couple will be colour blind? (a) 25% (b) 0% (c) 50% (d) 75%

Last Answer : (c) 50%

Due to the cross between TTRr × ttrr the resultant progenies show what percent of tall, red flowered plants? (a) 50% (b) 75% (c) 25% (d) 100%

Description : Due to the cross between TTRr × ttrr the resultant progenies show what percent of tall, red flowered plants? (a) 50% (b) 75% (c) 25% (d) 100%

Last Answer : (a) 50%

In a plant, red fruit (R) is dominant over yellow fruit (r) and tallness (T) is dominant over shortness (t). If a plant with RRTt genotype is crossed with a plant that is rrtt, (a) 25% will be tall with red fruit (b) 50% will be tall with red fruit (c) 75% will be tall with red fruit (d) all the offspring will be tall with red fruit

Description : In a plant, red fruit (R) is dominant over yellow fruit (r) and tallness (T) is dominant over shortness (t). If a plant with RRTt genotype is crossed with a plant that is rrtt, (a) 25% will be ... with red fruit (c) 75% will be tall with red fruit (d) all the offspring will be tall with red fruit

Last Answer : (b) 50% will be tall with red fruit

tt mates with Tt. What will be characteristic of offspring? (a) 75% recessive (b) 50% recessive (c) 25% recessive (d) All dominant

Description : tt mates with Tt. What will be characteristic of offspring? (a) 75% recessive (b) 50% recessive (c) 25% recessive (d) All dominant

Last Answer : b) 50% recessive

Which of the following represents a racemic mixture? (a) 75% (R)-2-butanol, 25% (S)-2-butanol (b) 25% (R)-2-butanol, 75% (S)-2-butanol (c) 50% (R)-2-butanol, 50% (S)-2-butanol (d) none of the above

Description : Which of the following represents a racemic mixture? (a) 75% (R)-2-butanol, 25% (S)-2-butanol (b) 25% (R)-2-butanol, 75% (S)-2-butanol (c) 50% (R)-2-butanol, 50% (S)-2-butanol (d) none of the above

Last Answer : 50% (R)-2-butanol, 50% (S)-2-butanol

Cooling efficiency of a cooling tower is significantly affected under cross-wind condition and might decrease to……… in the range of moderate to high wind velocity condition. a) 50% c) 25% b) 75% d) 90%

Description : Cooling efficiency of a cooling tower is significantly affected under cross-wind condition and might decrease to……… in the range of moderate to high wind velocity condition. a) 50% c) 25% b) 75% d) 90%

Last Answer : 75%

For ductility consideration, the maximum percentage of steel used should not exceed ------- of the balanced steel [ A ] 25% [ B ] 50% [ C ] 60% [ D ] 75%

Description : For ductility consideration, the maximum percentage of steel used should not exceed ------- of the balanced steel [ A ] 25% [ B ] 50% [ C ] 60% [ D ] 75%

Last Answer : [ D ] 75%

In the P generation, a tall plant is crossed with a short plant. The probability that an F2 plant will be tall is a. 50%. b. 75%. c. 25%. d. 100%.

Description : In the P generation, a tall plant is crossed with a short plant. The probability that an F2 plant will be tall is a. 50%. b. 75%. c. 25%. d. 100%.

Last Answer : b. 75%.

The density of lead is 12 grams per cm3. A lead brick has a mass of 1.5 kilograms. Its dimensions are 10 cm by 5 cm by 4 cm. Is it: w) More than 75% hollow x) Between 50 and 75% hollow y) Between 25 and 50% hollow z) Between 0 and 25% hollow

Description : The density of lead is 12 grams per cm3. A lead brick has a mass of 1.5 kilograms. Its dimensions are 10 cm by 5 cm by 4 cm. Is it: w) More than 75% hollow x) Between 50 and 75% hollow y) Between 25 and 50% hollow z) Between 0 and 25% hollow

Last Answer : ANSWER: Y -- BETWEEN 25 AND 50% HOLLOW

When a beam is subjected to a bending moment the strain in a layer is …………the distance from the neutral axis. (a) Independent of (b) Directly proportional to (c) Inversely proportional to (d) None of these

Description : When a beam is subjected to a bending moment the strain in a layer is …………the distance from the neutral axis. (a) Independent of (b) Directly proportional to (c) Inversely proportional to (d) None of these

Last Answer : (b) Directly proportional to

Coil springs absorb shocks by (a) bending (b) twisting (c) compression (d) tension

Description : Coil springs absorb shocks by (a) bending (b) twisting (c) compression (d) tension

Last Answer : (c) compression

Leaf springs absorb shocks by (a) bending (b) twisting (c) compression (d) tension

Description : Leaf springs absorb shocks by (a) bending (b) twisting (c) compression (d) tension

Last Answer : a) bending

Coil springs absorb shocks by (A) bending (B) twisting (C) compression (D) tension

Description : Coil springs absorb shocks by (A) bending (B) twisting (C) compression (D) tension

Last Answer : (C) compression

A spherical pressure vessel is made of thin magnesium plate 0.25 cm thick. The main diameter of the sphere is 600 cm and allowable stress in tension is 900 kg/cm2. The safe internal gas pressure for the vessel would be a) 0.5 kg/cm2 b) 1.5 kg/cm2 c) 4.5 kg/cm2 d) 5.7 kg/cm2

Description : A spherical pressure vessel is made of thin magnesium plate 0.25 cm thick. The main diameter of the sphere is 600 cm and allowable stress in tension is 900 kg/cm2. The safe internal gas pressure for the vessel would be a) 0.5 kg/cm2 b) 1.5 kg/cm2 c) 4.5 kg/cm2 d) 5.7 kg/cm2

Last Answer : b) 1.5 kg/cm2

The piston rod of a hydraulic cylinder exerts an operating force of 10kN. The allowable stress in the cylinder is 45N/mm². Calculate the thickness of the cylinder using Lame’s equation. Diameter of the cylinder is 40mm and pressure in cylinder is 10MPa. a) 2.05mm b) 4.2mm c) 5.07mm d) None of the listed

Description : The piston rod of a hydraulic cylinder exerts an operating force of 10kN. The allowable stress in the cylinder is 45N/mm². Calculate the thickness of the cylinder using Lame's equation. Diameter of the cylinder is 40mm and ... is 10MPa. a) 2.05mm b) 4.2mm c) 5.07mm d) None of the listed

Last Answer : c) 5.07mm

According to ASME code, maximum allowable shear stress is taken as X% of yield strength or Y% of ultimate strength. a) X=30 Y=18 b) X=30 Y=30 c) X=18 Y=18 d) X=18 Y=30

Description : According to ASME code, maximum allowable shear stress is taken as X% of yield strength or Y% of ultimate strength. a) X=30 Y=18 b) X=30 Y=30 c) X=18 Y=18 d) X=18 Y=30

Last Answer : a) X=30 Y=18

A square object of 4 mm is subjected to a force of 3000 N. What is the maximum allowable shear stress acting on it? a. 250.14 mm2 b. 281.25 mm2 c. 400.32 mm2 d. 500 mm2

Description : A square object of 4 mm is subjected to a force of 3000 N. What is the maximum allowable shear stress acting on it? a. 250.14 mm2 b. 281.25 mm2 c. 400.32 mm2 d. 500 mm2

Last Answer : b. 281.25 mm2

A circular pipe is subjected to maximum shear force of 60 kN. What is the diameter of the pipe if maximum allowable shear stress is 5 Mpa? a. 27.311 mm b. 75.56 mm c. 142.72 mm d. 692.10 mm

Description : A circular pipe is subjected to maximum shear force of 60 kN. What is the diameter of the pipe if maximum allowable shear stress is 5 Mpa? a. 27.311 mm b. 75.56 mm c. 142.72 mm d. 692.10 mm

Last Answer : c. 142.72 mm

Chrome vanadium steels usually contain 0.8 to 1.1% Cr, 0.25 to 0.35% C and < 0.25% V. It is (A) Used for making axle & shafts of aeroplanes, automobiles and locomotives (B) Having poor fatigue resistance (C) Having poor toughness (D) Not helpful in producing cleaner steel due to oxidising action of vanadium

Description : Chrome vanadium steels usually contain 0.8 to 1.1% Cr, 0.25 to 0.35% C and < 0.25% V. It is (A) Used for making axle & shafts of aeroplanes, automobiles and locomotives (B) ... resistance (C) Having poor toughness (D) Not helpful in producing cleaner steel due to oxidising action of vanadium

Last Answer : (A) Used for making axle & shafts of aeroplanes, automobiles and locomotives

The shafts will have same strength on the basis of torsional rigidity, if (a) diameter and length of both shafts is same (b) material of both shafts is same (c) angle of twist for both shafts is same (d) all of above conditions are satisfied

Description : The shafts will have same strength on the basis of torsional rigidity, if (a) diameter and length of both shafts is same (b) material of both shafts is same (c) angle of twist for both shafts is same (d) all of above conditions are satisfied

Last Answer : (d) all of above conditions are satisfied

Flexible shafts have ___ rigidity in torsion making them flexible. a) Low b) High c) Very high d) Infinitely small

Description : Flexible shafts have ___ rigidity in torsion making them flexible. a) Low b) High c) Very high d) Infinitely small

Last Answer : b) High

Solid shafts are used in epicyclic gearboxes. a) True b) False

Description : Solid shafts are used in epicyclic gearboxes. a) True b) False

Last Answer : b) False