When a thin cylindrical shell is subjected to an internal pressure, there will be a) a decrease in diameter and length of the shell b) an increase in diameter and length of the shell c) an increase in diameter and decrease in length of the shell d) a decrease in diameter and increase in length of the shell

When a thin cylindrical shell is subjected to an internal pressure, there will be
a) a decrease in diameter and length of the shell
b) an increase in diameter and length of the shell
c) an increase in diameter and decrease in length of the shell
d) a decrease in diameter and increase in length of the shell
by

1 Answer

Answer :

b) an increase in diameter and length of the shell
by

Related questions

Stresses in a thin cylindrical shell under internal pressure is independent of a. Diameter b. Thickness c. Length d. Diameter and thickness

Description : Stresses in a thin cylindrical shell under internal pressure is independent of a. Diameter b. Thickness c. Length d. Diameter and thickness

Last Answer : c. Length

In a thick cylindrical shell subjected to an internal pressure (p), the radial stress across the thickness of a cylinder is a) maximum at the outer surface and minimum at the inner surface b) maximum at the inner surface and minimum at the outer surface c) maximum at the inner surface and zero at the outer surface d) maximum at the outer surface and zero at the inner surface

Description : In a thick cylindrical shell subjected to an internal pressure (p), the radial stress across the thickness of a cylinder is a) maximum at the outer surface and minimum at the inner surface b) maximum ... and zero at the outer surface d) maximum at the outer surface and zero at the inner surface

Last Answer : c) maximum at the inner surface and zero at the outer surface

Among the cylindrical and spherical thin vessels of same material, diameter and pressure which has the lesser thickness a. Cylindrical shell b. Spherical shell c. Cylindrical shell with semi spherical heads d. None

Description : Among the cylindrical and spherical thin vessels of same material, diameter and pressure which has the lesser thickness a. Cylindrical shell b. Spherical shell c. Cylindrical shell with semi spherical heads d. None

Last Answer : b. Spherical shell

A thin cylindrical shell under internal pressure can fail by a. Shear b. Compression c. Tension d. None

Description : A thin cylindrical shell under internal pressure can fail by a. Shear b. Compression c. Tension d. None

Last Answer : c. Tension

What is the ratio of hoop stresses in a spherical vs cylindrical shell of same diameter, thickness and under same pressure? a. 4:1 b. 2:1 c. 1:2 d. 1:4

Description : What is the ratio of hoop stresses in a spherical vs cylindrical shell of same diameter, thickness and under same pressure? a. 4:1 b. 2:1 c. 1:2 d. 1:4

Last Answer : c. 1:2

A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder. a) 540mm b) 270mm c) 400mm d) 350mm

Description : A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder. a) 540mm b) 270mm c) 400mm d) 350mm

Last Answer : a) 540mm

A thin cylindrical under internal pressure can fail along the a. Longitudinal joint b. Circumferential joint c. Longitudinal as well as circumferential joint d. None

Description : A thin cylindrical under internal pressure can fail along the a. Longitudinal joint b. Circumferential joint c. Longitudinal as well as circumferential joint d. None

Last Answer : c. Longitudinal as well as circumferential joint

A thin spherical shell under internal pressure will fail under a. Maximum shear stress b. Principal compressive stress c. Principal tensile stress d. None

Description : A thin spherical shell under internal pressure will fail under a. Maximum shear stress b. Principal compressive stress c. Principal tensile stress d. None

Last Answer : c. Principal tensile stress

A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the thickness of the cylinder if it is twice the diameter of the cylinder. a) 12mm b) 4mm c) 8mm d) 16mm

Description : A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the thickness of the cylinder if it is twice the diameter of the cylinder. a) 12mm b) 4mm c) 8mm d) 16mm

Last Answer : c) 8mm

A spherical pressure vessel is made of thin magnesium plate 0.25 cm thick. The main diameter of the sphere is 600 cm and allowable stress in tension is 900 kg/cm2. The safe internal gas pressure for the vessel would be a) 0.5 kg/cm2 b) 1.5 kg/cm2 c) 4.5 kg/cm2 d) 5.7 kg/cm2

Description : A spherical pressure vessel is made of thin magnesium plate 0.25 cm thick. The main diameter of the sphere is 600 cm and allowable stress in tension is 900 kg/cm2. The safe internal gas pressure for the vessel would be a) 0.5 kg/cm2 b) 1.5 kg/cm2 c) 4.5 kg/cm2 d) 5.7 kg/cm2

Last Answer : b) 1.5 kg/cm2

Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm

Description : Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm

Last Answer : c. 587.1 mm

Stiffness of the spring can be increased by a. increase the number of turns b. increase the free length c. decrease the number of turns d. decrease the spring wire diameter

Description : Stiffness of the spring can be increased by a. increase the number of turns b. increase the free length c. decrease the number of turns d. decrease the spring wire diameter

Last Answer : c. decrease the number

Design of a thin shell under pressure is done on the basis of a. Radial stress b. Longitudinal stress c. Hoop stress d. All the three stresses

Description : Design of a thin shell under pressure is done on the basis of a. Radial stress b. Longitudinal stress c. Hoop stress d. All the three stresses

Last Answer : c. Hoop stress

Lame's theory is associated with a) thick cylindrical shells b) thin cylindrical shells c) direct and bending stresses d) none of these

Description : Lame's theory is associated with a) thick cylindrical shells b) thin cylindrical shells c) direct and bending stresses d) none of these

Last Answer : a) thick cylindrical shells

A thick cylinder is subjected to an internal pressure of 60 MPa. If the hoop stress on the outer surface is 150 MPa, then the hoop stress on the internal surface is a) 105 MPa b) 180 MPa c) 210 MPa d) 135 MPa.

Description : A thick cylinder is subjected to an internal pressure of 60 MPa. If the hoop stress on the outer surface is 150 MPa, then the hoop stress on the internal surface is a) 105 MPa b) 180 MPa c) 210 MPa d) 135 MPa.

Last Answer : c) 210 MPa

In a thin shell which stress is negligible a) σh b) σl c) σr d) None

Description : In a thin shell which stress is negligible a) σh b) σl c) σr d) None

Last Answer : c) σr

Value of σr in a thin shell is a) pD/2t b) pD/4t c) pD/3t d) None

Description : Value of σr in a thin shell is a) pD/2t b) pD/4t c) pD/3t d) None

Last Answer : d) None

Longitudinal strain in a thin shell is a) σh /E b) σl /E c) σr /E d) None

Description : Longitudinal strain in a thin shell is a) σh /E b) σl /E c) σr /E d) None

Last Answer : d) None

Hoop strain in a thin shell is a) σh /E b) σl /E c) 3 σh /E d) None

Description : Hoop strain in a thin shell is a) σh /E b) σl /E c) 3 σh /E d) None

Last Answer : d) None

Which one is most important in a thin shell? a) d/t <20 b) d/t> 10 c) Stresses are uniform d) None

Description : Which one is most important in a thin shell? a) d/t 10 c) Stresses are uniform d) None

Last Answer : c) Stresses are uniform

Which is most predominant type of failure in a thin shell? a. Bearing failure b. Compression failure c. Crushing failure d. None

Description : Which is most predominant type of failure in a thin shell? a. Bearing failure b. Compression failure c. Crushing failure d. None

Last Answer : d. None

Radial stress in a thin shell is given by a. pD/2t b. pD/4t c. pD/3t d. None

Description : Radial stress in a thin shell is given by a. pD/2t b. pD/4t c. pD/3t d. None

Last Answer : d. None

Which stress is the least in a thin shell a. Longitudinal stress b. Hoop stress c. Radial stress d. None

Description : Which stress is the least in a thin shell a. Longitudinal stress b. Hoop stress c. Radial stress d. None

Last Answer : c. Radial stress

The close-coiled helical springs ‘A’ and ‘B’ are of same material, same coil diameter, same wire diameter and subjected to same load. If the number of turns of spring ‘A’ is half that of spring ‘B’, the ratio of deflection of spring ‘A’ to spring ‘B’ is (a)1/2 (b) 1 (c) 2 (d) 4

Description : The close-coiled helical springs ‘A’ and ‘B’ are of same material, same coil diameter, same wire diameter and subjected to same load. If the number of turns of spring ‘A’ is half that of spring ‘B’, the ratio of deflection of spring ‘A’ to spring ‘B’ is (a)1/2 (b) 1 (c) 2 (d) 4

Last Answer : (a)1/2

A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 Mpa. It is further subjected to a torque of 10 kNm. The maximum principal stress experienced on the shaft is closest to (a) 41Mpa (b) 82 Mpa (c) 164 Mpa (d) 204 Mpa

Description : A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 Mpa. It is further subjected to a torque of 10 kNm. The maximum principal stress experienced on the shaft is closest to (a) 41Mpa (b) 82 Mpa (c) 164 Mpa (d) 204 Mpa

Last Answer : (b) 82 Mpa

A solid shaft has diameter 80 mm. It is subjected to a torque of 4 KNm. The maximum shear stress induced in the shaft would be (a) 75/p N/mm2 (b) 250/p N/mm2 (c) 125/p N/mm2 (d) 150/p N/mm2

Description : A solid shaft has diameter 80 mm. It is subjected to a torque of 4 KNm. The maximum shear stress induced in the shaft would be (a) 75/p N/mm2 (b) 250/p N/mm2 (c) 125/p N/mm2 (d) 150/p N/mm2

Last Answer : (c) 125/p N/mm2

What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2

Description : What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2

Last Answer : b. 14.69 N/mm2

What is the maximum principle stress induced in a solid shaft of 40 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 150 kN.mm respectively? a. 21.69 N/mm2 b. 28.1 N/mm2 c. 50.57 N/mm2 d. 52.32 N/mm2

Description : What is the maximum principle stress induced in a solid shaft of 40 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 150 kN.mm respectively? a. 21.69 N/mm2 b. 28.1 N/mm2 c. 50.57 N/mm2 d. 52.32 N/mm2

Last Answer : c. 50.57 N/mm2

What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2

Description : What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2

Last Answer : c. 20.120 N/mm2

The ratio of strength of a hollow shaft to that of a solid shaft subjected to torsion if both are of the same material and of the same outer diameters, the inner diameter of hollow shaft being half of the outer diameter is a. 15/16 b. 16/15 c. 7/8 d. 8/7

Description : The ratio of strength of a hollow shaft to that of a solid shaft subjected to torsion if both are of the same material and of the same outer diameters, the inner diameter of hollow shaft being half of the outer diameter is a. 15/16 b. 16/15 c. 7/8 d. 8/7

Last Answer : a. 15/16

A circular pipe is subjected to maximum shear force of 60 kN. What is the diameter of the pipe if maximum allowable shear stress is 5 Mpa? a. 27.311 mm b. 75.56 mm c. 142.72 mm d. 692.10 mm

Description : A circular pipe is subjected to maximum shear force of 60 kN. What is the diameter of the pipe if maximum allowable shear stress is 5 Mpa? a. 27.311 mm b. 75.56 mm c. 142.72 mm d. 692.10 mm

Last Answer : c. 142.72 mm

A rod, 120cm long and of diameter 3.0 cm is subjected to an axial pull of 18 kN. The stress in N/mm2 is. a. 22.57 b. 23.47 c. 24.57 d. 25.47

Description : A rod, 120cm long and of diameter 3.0 cm is subjected to an axial pull of 18 kN. The stress in N/mm2 is. a. 22.57 b. 23.47 c. 24.57 d. 25.47

Last Answer : d. 25.47

Cylinder having inner diameter to wall thickness ratio less than 15 are a) Thin cylinders b) Thick Cylinders c) Moderate cylinders d) none of the above

Description : Cylinder having inner diameter to wall thickness ratio less than 15 are a) Thin cylinders b) Thick Cylinders c) Moderate cylinders d) none of the above

Last Answer : b) Thick Cylinders

Keeping loading same but increasing the length, normal stresses in a long column will (a) Increase (b) Decrease (c) No change (d) None

Description : Keeping loading same but increasing the length, normal stresses in a long column will (a) Increase (b) Decrease (c) No change (d) None

Last Answer : (b) Decrease

Keeping loading same but increasing the length, shear stresses in a beam will (a) Increase (b) Decrease (c) No change (d) None

Description : Keeping loading same but increasing the length, shear stresses in a beam will (a) Increase (b) Decrease (c) No change (d) None

Last Answer : (c) No change

Keeping loading same but increasing the length, normal stresses in a beam will (a) Increase (b) Decrease (c) No change (d) None

Description : Keeping loading same but increasing the length, normal stresses in a beam will (a) Increase (b) Decrease (c) No change (d) None

Last Answer : (a) Increase

A circular shaft subjected to torsion undergoes a twist of 10in a length of 120 cm. If the maximum shear stress induced is limited to 1000 kg/cm2and if modulus of rigidity G = 0.8 x 106then the radius of the shaft should be (a) p/8 (b) p/27 (c) 18/p (d) 27/p

Description : A circular shaft subjected to torsion undergoes a twist of 10in a length of 120 cm. If the maximum shear stress induced is limited to 1000 kg/cm2and if modulus of rigidity G = 0.8 x 106then the radius of the shaft should be (a) p/8 (b) p/27 (c) 18/p (d) 27/p

Last Answer : (d) 27/p

In a cantilever subjected to a concentrated load (W) at the free end and having length =l, Maximum bending moment is (a) Wl at the free end (b) Wl at the fixed end (c) Wl/2 at the fixed end (d) Wl at the free end

Description : In a cantilever subjected to a concentrated load (W) at the free end and having length =l, Maximum bending moment is (a) Wl at the free end (b) Wl at the fixed end (c) Wl/2 at the fixed end (d) Wl at the free end

Last Answer : (b) Wl at the fixed end

In a simply supported beam subjected to uniformly distributed load (w) over the entire length (l), total load=W, maximum Bending moment is (a) Wl/8 or wl2/8 at the mid-point (b) Wl/8 or wl2/8 at the end (c) Wl/4 or wl2/4 (d) Wl/2

Description : In a simply supported beam subjected to uniformly distributed load (w) over the entire length (l), total load=W, maximum Bending moment is (a) Wl/8 or wl2/8 at the mid-point (b) Wl/8 or wl2/8 at the end (c) Wl/4 or wl2/4 (d) Wl/2

Last Answer : (a) Wl/8 or wl2/8 at the mid-point

18.The total extension of a taper rod of length ‘L’ and end diameters ‘D1’ and ‘D2’, subjected to a load (P), is given of a. 4PL/ΠE. D1D2 b. 3PL/ΠE. D1D2 c. 2PL/ΠE. D1D2 d. PL/ΠE.D1D2 Where E=Young’s modulus of elasticity

Description : 18.The total extension of a taper rod of length ‘L’ and end diameters ‘D1’ and ‘D2’, subjected to a load (P), is given of a. 4PL/ΠE. D1D2 b. 3PL/ΠE. D1D2 c. 2PL/ΠE. D1D2 d. PL/ΠE.D1D2 Where E=Young’s modulus of elasticity

Last Answer : a. 4PL/ΠE. D1D2

When a bar is subjected to increase in temperature and its deformation is prevented, the stress induced in the bar is (a) Tensile (b) Compressive (c) Shear (d) None of the above

Description : When a bar is subjected to increase in temperature and its deformation is prevented, the stress induced in the bar is (a) Tensile (b) Compressive (c) Shear (d) None of the above

Last Answer : (b) Compressive

A compression spring is made of music wire of 2 mm diameter having a shear strength and shear modulus of 800 Mpa and 80 Gpa respectively. The mean coil diameter is 20mm, free length is 40 mm, and the number of active coils is 10. If the mean coil diameter is reduced to 10 mm, the stiffness of the spring is approximately a. increased by 8 times b. decreased by 2 times c. increased by 2 times d. decreased by 8 times

Description : A compression spring is made of music wire of 2 mm diameter having a shear strength and shear modulus of 800 Mpa and 80 Gpa respectively. The mean coil diameter is 20mm, free length is 40 mm, and the number ... by 8 times b. decreased by 2 times c. increased by 2 times d. decreased by 8 times

Last Answer : a. increased by 8 times

The length of a column, having a uniform circular cross-section of 7.5 cm diameter and whose endsare hinged, is 5 m. If the value of E for the material is 2100 tonnes/cm2, the permissible maximumcrippling load will be (a) 1.288 tonnes (b) 12.88 (c) 128.8 tonnes (d) 288.0

Description : The length of a column, having a uniform circular cross-section of 7.5 cm diameter and whose endsare hinged, is 5 m. If the value of E for the material is 2100 tonnes/cm2, the permissible maximumcrippling load will be (a) 1.288 tonnes (b) 12.88 (c) 128.8 tonnes (d) 288.0

Last Answer : (b) 12.88

The shafts will have same strength on the basis of torsional rigidity, if (a) diameter and length of both shafts is same (b) material of both shafts is same (c) angle of twist for both shafts is same (d) all of above conditions are satisfied

Description : The shafts will have same strength on the basis of torsional rigidity, if (a) diameter and length of both shafts is same (b) material of both shafts is same (c) angle of twist for both shafts is same (d) all of above conditions are satisfied

Last Answer : (d) all of above conditions are satisfied

Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm². a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm

Description : Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm². a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm

Last Answer : b) 41.2mm

A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum permissible angle of twist in the shaft is 1o. The inner diameter of the shaft is 0.7 times the outer diameter. The modulus of rigidity is 80 GPa. The outside diameter (in mm) of the shaft is _______. (a) 43 to 45 (b) 50to 60 (c) 70 to 80 (d) 85 to 100

Description : A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum permissible angle of twist in the shaft is 1o. The inner diameter of the shaft is 0.7 times the outer diameter. The modulus of ... shaft is _______. (a) 43 to 45 (b) 50to 60 (c) 70 to 80 (d) 85 to 100

Last Answer : (a) 43 to 45

A close coil helical spring when subjected to a moment M having its axis along the axis of the helix (A) It is subjected to pure bending (B) Its mean diameter will decrease (C) Its number of coils will increase (D) All the above

Description : A close coil helical spring when subjected to a moment M having its axis along the axis of the helix  (A) It is subjected to pure bending  (B) Its mean diameter will decrease  (C) Its number of coils will increase  (D) All the above 

Last Answer : (A) It is subjected to pure bending 

A sudden increase or decrease in shear force diagram between any two points indicates that there is (a) No loading between the two points (b) Point loads between the two points (c) U.D.L. between the two points (d) None of these

Description : A sudden increase or decrease in shear force diagram between any two points indicates that there is (a) No loading between the two points (b) Point loads between the two points (c) U.D.L. between the two points (d) None of these

Last Answer : (b) Point loads between the two points

The laminated springs are given initial curvature (a) To have uniform strength (b) To make it more economical (c) So that plates may become flat, when subjected to design load (d) None of these

Description : The laminated springs are given initial curvature (a) To have uniform strength (b) To make it more economical (c) So that plates may become flat, when subjected to design load (d) None of these

Last Answer : (c) So that plates may become

Two concentric springs with stiffness equal to 100 N/mm and 80 N/mm respectively, when subjected to load of 900N will deflect by a. 9mm b. 11.25 mm c. 5mm d. 31.5 mm

Description : Two concentric springs with stiffness equal to 100 N/mm and 80 N/mm respectively, when subjected to load of 900N will deflect by a. 9mm b. 11.25 mm c. 5mm d. 31.5 mm

Last Answer : c. 5mm