A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the thickness of the cylinder if it is twice the diameter of the cylinder. a) 12mm b) 4mm c) 8mm d) 16mm

A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of  21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the thickness of  the cylinder if it is twice the diameter of the cylinder.
a) 12mm
b) 4mm
c) 8mm
d) 16mm
by

1 Answer

Answer :

c) 8mm
by

Related questions

A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder. a) 540mm b) 270mm c) 400mm d) 350mm

Description : A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder. a) 540mm b) 270mm c) 400mm d) 350mm

Last Answer : a) 540mm

A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the leaves are 100mm and 12mm respectively. If modulus of elasticity is 207000N/mm², calculate the initial nip. (a) 26.8mm (b) 24.9mm (c) 22.5mm (d)23.1mm

Description : A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the ... /mm², calculate the initial nip. (a) 26.8mm (b) 24.9mm (c) 22.5mm (d)23.1mm

Last Answer : b) 24.9mm

The diameter of bars used for distribution reinforcement in slabs, may vary from (a) 2 to 4mm (b) 4 to 6mm (c) 6mm to 8mm (d) 8 to 12mm

Description : The diameter of bars used for distribution reinforcement in slabs, may vary from (a) 2 to 4mm (b) 4 to 6mm (c) 6mm to 8mm (d) 8 to 12mm

Last Answer : (c) 6mm to 8mm

The piston rod of a hydraulic cylinder exerts an operating force of 10kN. The allowable stress in the cylinder is 45N/mm². Calculate the thickness of the cylinder using Lame’s equation. Diameter of the cylinder is 40mm and pressure in cylinder is 10MPa. a) 2.05mm b) 4.2mm c) 5.07mm d) None of the listed

Description : The piston rod of a hydraulic cylinder exerts an operating force of 10kN. The allowable stress in the cylinder is 45N/mm². Calculate the thickness of the cylinder using Lame's equation. Diameter of the cylinder is 40mm and ... is 10MPa. a) 2.05mm b) 4.2mm c) 5.07mm d) None of the listed

Last Answer : c) 5.07mm

Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm². a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm

Description : Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm². a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm

Last Answer : b) 41.2mm

In a thick cylindrical shell subjected to an internal pressure (p), the radial stress across the thickness of a cylinder is a) maximum at the outer surface and minimum at the inner surface b) maximum at the inner surface and minimum at the outer surface c) maximum at the inner surface and zero at the outer surface d) maximum at the outer surface and zero at the inner surface

Description : In a thick cylindrical shell subjected to an internal pressure (p), the radial stress across the thickness of a cylinder is a) maximum at the outer surface and minimum at the inner surface b) maximum ... and zero at the outer surface d) maximum at the outer surface and zero at the inner surface

Last Answer : c) maximum at the inner surface and zero at the outer surface

The condition will be called as thin flange, when the flange thickness becomes less the: (a) 10mm (b) 12mm (c) 16mm* (d) 15mm

Description : The condition will be called as thin flange, when the flange thickness becomes less the: (a) 10mm (b) 12mm (c) 16mm* (d) 15mm

Last Answer : (c) 16mm*

As per IRCA rules, the rejection limits for wheel flange thickness is - (a) 38mm (b) 25.4mm (c) 16mm* (d) 20 mm

Description : As per IRCA rules, the rejection limits for wheel flange thickness is - (a) 38mm (b) 25.4mm (c) 16mm* (d) 20 mm

Last Answer : (c) 16mm*

Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm

Description : Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm

Last Answer : c. 587.1 mm

A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the leaves are 100mm and 12mm respectively. Calculate the initial pre load required to close the nip. (a) 4332.2N (b) 4674.1N (c) 4985.4N (d) Can’t be determined

Description : A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the ... close the nip. (a) 4332.2N (b) 4674.1N (c) 4985.4N (d) Can't be determined

Last Answer : (b) 4674.1N

A thick cylinder is subjected to an internal pressure of 60 MPa. If the hoop stress on the outer surface is 150 MPa, then the hoop stress on the internal surface is a) 105 MPa b) 180 MPa c) 210 MPa d) 135 MPa.

Description : A thick cylinder is subjected to an internal pressure of 60 MPa. If the hoop stress on the outer surface is 150 MPa, then the hoop stress on the internal surface is a) 105 MPa b) 180 MPa c) 210 MPa d) 135 MPa.

Last Answer : c) 210 MPa

A short, hollow cast iron cylinder with a wall thickness of 1 cm is to carry a compressive load of 10 tonnes. If the working stress in compression is 800 kg/cm2, the outside diameter of the cylinder should not be less than a) 0.5cm b) 5 cm c) 2.5cm d) 4.5 cm

Description : A short, hollow cast iron cylinder with a wall thickness of 1 cm is to carry a compressive load of 10 tonnes. If the working stress in compression is 800 kg/cm2, the outside diameter of the cylinder should not be less than a) 0.5cm b) 5 cm c) 2.5cm d) 4.5 cm

Last Answer : b) 5 cm

The ratio of strength of a hollow shaft to that of a solid shaft subjected to torsion if both are of the same material and of the same outer diameters, the inner diameter of hollow shaft being half of the outer diameter is a. 15/16 b. 16/15 c. 7/8 d. 8/7

Description : The ratio of strength of a hollow shaft to that of a solid shaft subjected to torsion if both are of the same material and of the same outer diameters, the inner diameter of hollow shaft being half of the outer diameter is a. 15/16 b. 16/15 c. 7/8 d. 8/7

Last Answer : a. 15/16

The diameter of bars for main reinforcement in slabs, may be (a) 2 to 4mm (b) 4 to 8mm (c) 8 to 14mm (d) 14 to 18mm

Description : The diameter of bars for main reinforcement in slabs, may be (a) 2 to 4mm (b) 4 to 8mm (c) 8 to 14mm (d) 14 to 18mm

Last Answer : (c) 8 to 14mm

An open-ended cylinder of radius and thickness is subjected to internal pressure . The Young's modulus for the material is and Poisson's ratio is . The longitudinal strain is (A) Zero (B) pr/TE (C) pr/2TE (D) None of these

Description : An open-ended cylinder of radius and thickness is subjected to internal pressure . The Young's modulus for the material is and Poisson's ratio is . The longitudinal strain is (A) Zero (B) pr/TE (C) pr/2TE (D) None of these

Last Answer : (A) Zero

When a thin cylindrical shell is subjected to an internal pressure, there will be a) a decrease in diameter and length of the shell b) an increase in diameter and length of the shell c) an increase in diameter and decrease in length of the shell d) a decrease in diameter and increase in length of the shell

Description : When a thin cylindrical shell is subjected to an internal pressure, there will be a) a decrease in diameter and length of the shell b) an increase in diameter and length of the shell c) an ... and decrease in length of the shell d) a decrease in diameter and increase in length of the shell

Last Answer : b) an increase in diameter and length of the shell

Cylinder having inner diameter to wall thickness ratio less than 15 are a) Thin cylinders b) Thick Cylinders c) Moderate cylinders d) none of the above

Description : Cylinder having inner diameter to wall thickness ratio less than 15 are a) Thin cylinders b) Thick Cylinders c) Moderate cylinders d) none of the above

Last Answer : b) Thick Cylinders

A concentric spring consists of 2 sprigs of diameter 10mm and 4mm. The net force acting on the composite spring is 5000N. Find the force acting on each of the two springs. (a) 1232.2N and 3767.8N (b) 786.4N and 4213.6N (c) 689.7N and 4310.3N (d) 645.3N and 4354.7N

Description : A concentric spring consists of 2 sprigs of diameter 10mm and 4mm. The net force acting on the composite spring is 5000N. Find the force acting on each of the two springs. (a) 1232.2N and 3767.8N (b) 786.4N and 4213.6N (c) 689.7N and 4310.3N (d) 645.3N and 4354.7N

Last Answer : (c) 689.7N and 4310.3N

Stresses in a thin cylindrical shell under internal pressure is independent of a. Diameter b. Thickness c. Length d. Diameter and thickness

Description : Stresses in a thin cylindrical shell under internal pressure is independent of a. Diameter b. Thickness c. Length d. Diameter and thickness

Last Answer : c. Length

Find total number coils in a spring having square and ground ends. Deflection in the spring is 6mm when load of 1100N is applied. Modulus of rigidity is 81370N/mm². Wire diameter and pitch circle diameter are 10mm and 50mm respectively. a) 7 b) 6 c) 5 d) 4

Description : Find total number coils in a spring having square and ground ends. Deflection in the spring is 6mm when load of 1100N is applied. Modulus of rigidity is 81370N/mm². Wire diameter and pitch circle diameter are 10mm and 50mm respectively. a) 7 b) 6 c) 5 d) 4

Last Answer : a) 7

Find the shear stress in the spring wire used to design a helical compression sprig if a load of 1200N is applied on the spring. Spring index is 6, and wire diameter 7mm. a) 452.2N/mm² b) 468.6N/mm² c) 512.2N/mm² d) None of the listed

Description : Find the shear stress in the spring wire used to design a helical compression sprig if a load of 1200N is applied on the spring. Spring index is 6, and wire diameter 7mm. a) 452.2N/mm² b) 468.6N/mm² c) 512.2N/mm² d) None of the listed

Last Answer : b) 468.6N/mm²

If yielding strength=400N/mm², the find the permissible shear stress according to ASME standards. a) 72 N/mm² b) 76 N/mm² c) 268 N/mm² d) 422 N/mm²

Description : If yielding strength=400N/mm², the find the permissible shear stress according to ASME standards. a) 72 N/mm² b) 76 N/mm² c) 268 N/mm² d) 422 N/mm²

Last Answer : a) 72 N/mm²

Two shafts in torsion will have equal strength if a. Only diameter of the shafts is same b. Only angle of twist of the shaft is same c. Only material of the shaft is same d. Only torque transmitting capacity of the shaft is same

Description : Two shafts in torsion will have equal strength if a. Only diameter of the shafts is same b. Only angle of twist of the shaft is same c. Only material of the shaft is same d. Only torque transmitting capacity of the shaft is same

Last Answer : d. Only torque transmitting capacity of the shaft is same

Among the cylindrical and spherical thin vessels of same material, diameter and pressure which has the lesser thickness a. Cylindrical shell b. Spherical shell c. Cylindrical shell with semi spherical heads d. None

Description : Among the cylindrical and spherical thin vessels of same material, diameter and pressure which has the lesser thickness a. Cylindrical shell b. Spherical shell c. Cylindrical shell with semi spherical heads d. None

Last Answer : b. Spherical shell

If diameter of a shaft is doubled the power transmitted capacity will be a. Either twice or half b. Four times c. Eight times d. Same

Description : If diameter of a shaft is doubled the power transmitted capacity will be a. Either twice or half b. Four times c. Eight times d. Same

Last Answer : c. Eight times

A water main 1 m in diameter contains a fluid having pressure 1 N/mm2. If the maximum permissible tensile stress in the metal is 20 N/mm2, th thickness of the metal required would be a) 2 cm b) 2.5cm c) 1 cm d) 0.5 cm

Description : A water main 1 m in diameter contains a fluid having pressure 1 N/mm2. If the maximum permissible tensile stress in the metal is 20 N/mm2, th thickness of the metal required would be a) 2 cm b) 2.5cm c) 1 cm d) 0.5 cm

Last Answer : b) 2.5cm

The close-coiled helical springs ‘A’ and ‘B’ are of same material, same coil diameter, same wire diameter and subjected to same load. If the number of turns of spring ‘A’ is half that of spring ‘B’, the ratio of deflection of spring ‘A’ to spring ‘B’ is (a)1/2 (b) 1 (c) 2 (d) 4

Description : The close-coiled helical springs ‘A’ and ‘B’ are of same material, same coil diameter, same wire diameter and subjected to same load. If the number of turns of spring ‘A’ is half that of spring ‘B’, the ratio of deflection of spring ‘A’ to spring ‘B’ is (a)1/2 (b) 1 (c) 2 (d) 4

Last Answer : (a)1/2

Two shafts A and B are made of the same material. The diameter of the shaft A is twice as that of shaft B. The power transmitted by the shaft A will be ........... of shaft B. (a) twice (b) four times (c) eight times (d) sixteen times

Description : Two shafts A and B are made of the same material. The diameter of the shaft A is twice as that of shaft B. The power transmitted by the shaft A will be ........... of shaft B. (a) twice (b) four times (c) eight times (d) sixteen times

Last Answer : (c) eight times

A hollow prismatic beam of circular section is subjected to a torsional moment. The maximum shear stress occurs at (a) inner wall of cross section (b) middle of thickness (c) outer surface of shaft (d) none of these

Description : A hollow prismatic beam of circular section is subjected to a torsional moment. The maximum shear stress occurs at (a) inner wall of cross section (b) middle of thickness (c) outer surface of shaft (d) none of these

Last Answer : (c) outer surface of shaft

Maximum shear stress in a hollow shaft subjected to a torsional moment is at the a. Middle of thickness. b. At the inner surface of the shaft. c. At the outer surface of the shaft. d. At the middle surface of the shaft.

Description : Maximum shear stress in a hollow shaft subjected to a torsional moment is at the a. Middle of thickness. b. At the inner surface of the shaft. c. At the outer surface of the shaft. d. At the middle surface of the shaft.

Last Answer : c. At the outer surface of the shaft.

What is the ratio of hoop stresses in a spherical vs cylindrical shell of same diameter, thickness and under same pressure? a. 4:1 b. 2:1 c. 1:2 d. 1:4

Description : What is the ratio of hoop stresses in a spherical vs cylindrical shell of same diameter, thickness and under same pressure? a. 4:1 b. 2:1 c. 1:2 d. 1:4

Last Answer : c. 1:2

In a thick-cylinder pressurized from inside, the hoop stress is maximum at a) The center of the wall thickness b) the outer radius c) the inner radius d) both the inner and the outer radii

Description : In a thick-cylinder pressurized from inside, the hoop stress is maximum at a) The center of the wall thickness b) the outer radius c) the inner radius d) both the inner and the outer radii

Last Answer : c) the inner radius

Lame’s equation used to find the thickness of the cylinder is based on maximum strain failure. a) True b) False

Description : Lame’s equation used to find the thickness of the cylinder is based on maximum strain failure. a) True b) False

Last Answer : b) False

The ultimate tensile strength of structural mild steel is about (A) 160 N/mm² (B) 260 N/mm² (C) 420 N/mm² (D) 520 N/mm2

Description : The ultimate tensile strength of structural mild steel is about (A) 160 N/mm² (B) 260 N/mm² (C) 420 N/mm² (D) 520 N/mm

Last Answer : Answer: Option C

If is the internal pressure in a thin cylinder of diameter and thickness , the developed hoop stress, is (A) pd/2t (B) pd/4t (C) pd/t (D) 2pd/t

Description : If is the internal pressure in a thin cylinder of diameter and thickness , the developed hoop stress, is (A) pd/2t (B) pd/4t (C) pd/t (D) 2pd/t

Last Answer : (A) pd/2t

A thick cylinder under internal fluid pressure’ pi will have maximum stress at the 1. Outer radius 2. Inner radius 3. Mean radius 4. None

Description : A thick cylinder under internal fluid pressure’ pi will have maximum stress at the 1. Outer radius 2. Inner radius 3. Mean radius 4. None

Last Answer : 2. Inner radius

A rod, 120cm long and of diameter 3.0 cm is subjected to an axial pull of 18 kN. The stress in N/mm2 is. a. 22.57 b. 23.47 c. 24.57 d. 25.47

Description : A rod, 120cm long and of diameter 3.0 cm is subjected to an axial pull of 18 kN. The stress in N/mm2 is. a. 22.57 b. 23.47 c. 24.57 d. 25.47

Last Answer : d. 25.47

A spherical pressure vessel is made of thin magnesium plate 0.25 cm thick. The main diameter of the sphere is 600 cm and allowable stress in tension is 900 kg/cm2. The safe internal gas pressure for the vessel would be a) 0.5 kg/cm2 b) 1.5 kg/cm2 c) 4.5 kg/cm2 d) 5.7 kg/cm2

Description : A spherical pressure vessel is made of thin magnesium plate 0.25 cm thick. The main diameter of the sphere is 600 cm and allowable stress in tension is 900 kg/cm2. The safe internal gas pressure for the vessel would be a) 0.5 kg/cm2 b) 1.5 kg/cm2 c) 4.5 kg/cm2 d) 5.7 kg/cm2

Last Answer : b) 1.5 kg/cm2

The spring constant of a helical compression spring does not depend on a. Coil diameter b. Material strength c. Number of active turns d. wire diameter

Description : The spring constant of a helical compression spring does not depend on a. Coil diameter b. Material strength c. Number of active turns d. wire diameter

Last Answer : b. Material strength

The shafts will have same strength on the basis of torsional rigidity, if (a) diameter and length of both shafts is same (b) material of both shafts is same (c) angle of twist for both shafts is same (d) all of above conditions are satisfied

Description : The shafts will have same strength on the basis of torsional rigidity, if (a) diameter and length of both shafts is same (b) material of both shafts is same (c) angle of twist for both shafts is same (d) all of above conditions are satisfied

Last Answer : (d) all of above conditions are satisfied

Two shafts will have equal strength, if (a) diameter of both the shafts is same (b) angle of twist of both the shafts is same (c) material of both the shafts is same (d) twisting moment of both the shafts is same

Description : Two shafts will have equal strength, if (a) diameter of both the shafts is same (b) angle of twist of both the shafts is same (c) material of both the shafts is same (d) twisting moment of both the shafts is same

Last Answer : d) twisting moment of both the shafts is same

When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65

Description : When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65

Last Answer : (c) 0.50

According to ASME code, maximum allowable shear stress is taken as X% of yield strength or Y% of ultimate strength. a) X=30 Y=18 b) X=30 Y=30 c) X=18 Y=18 d) X=18 Y=30

Description : According to ASME code, maximum allowable shear stress is taken as X% of yield strength or Y% of ultimate strength. a) X=30 Y=18 b) X=30 Y=30 c) X=18 Y=18 d) X=18 Y=30

Last Answer : a) X=30 Y=18

Hooke’s law is applicable within (a)Elastic limit (b)Plastic limit (c)Fracture point (d) Ultimate strength

Description : Hooke’s law is applicable within (a)Elastic limit (b)Plastic limit (c)Fracture point (d) Ultimate strength

Last Answer : (a)Elastic limit

A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 Mpa. It is further subjected to a torque of 10 kNm. The maximum principal stress experienced on the shaft is closest to (a) 41Mpa (b) 82 Mpa (c) 164 Mpa (d) 204 Mpa

Description : A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 Mpa. It is further subjected to a torque of 10 kNm. The maximum principal stress experienced on the shaft is closest to (a) 41Mpa (b) 82 Mpa (c) 164 Mpa (d) 204 Mpa

Last Answer : (b) 82 Mpa

A solid shaft has diameter 80 mm. It is subjected to a torque of 4 KNm. The maximum shear stress induced in the shaft would be (a) 75/p N/mm2 (b) 250/p N/mm2 (c) 125/p N/mm2 (d) 150/p N/mm2

Description : A solid shaft has diameter 80 mm. It is subjected to a torque of 4 KNm. The maximum shear stress induced in the shaft would be (a) 75/p N/mm2 (b) 250/p N/mm2 (c) 125/p N/mm2 (d) 150/p N/mm2

Last Answer : (c) 125/p N/mm2

What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2

Description : What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2

Last Answer : b. 14.69 N/mm2

What is the maximum principle stress induced in a solid shaft of 40 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 150 kN.mm respectively? a. 21.69 N/mm2 b. 28.1 N/mm2 c. 50.57 N/mm2 d. 52.32 N/mm2

Description : What is the maximum principle stress induced in a solid shaft of 40 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 150 kN.mm respectively? a. 21.69 N/mm2 b. 28.1 N/mm2 c. 50.57 N/mm2 d. 52.32 N/mm2

Last Answer : c. 50.57 N/mm2

What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2

Description : What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2

Last Answer : c. 20.120 N/mm2

A circular pipe is subjected to maximum shear force of 60 kN. What is the diameter of the pipe if maximum allowable shear stress is 5 Mpa? a. 27.311 mm b. 75.56 mm c. 142.72 mm d. 692.10 mm

Description : A circular pipe is subjected to maximum shear force of 60 kN. What is the diameter of the pipe if maximum allowable shear stress is 5 Mpa? a. 27.311 mm b. 75.56 mm c. 142.72 mm d. 692.10 mm

Last Answer : c. 142.72 mm