A thin cylindrical under internal pressure can fail along the a. Longitudinal joint b. Circumferential joint c. Longitudinal as well as circumferential joint d. None

A thin cylindrical under internal pressure can fail along the
a. Longitudinal joint
b. Circumferential joint
c. Longitudinal as well as circumferential joint
d. None
by

1 Answer

Answer :

c. Longitudinal as well as circumferential joint
by

Related questions

A thin cylindrical shell under internal pressure can fail by a. Shear b. Compression c. Tension d. None

Description : A thin cylindrical shell under internal pressure can fail by a. Shear b. Compression c. Tension d. None

Last Answer : c. Tension

Stresses in a thin cylindrical shell under internal pressure is independent of a. Diameter b. Thickness c. Length d. Diameter and thickness

Description : Stresses in a thin cylindrical shell under internal pressure is independent of a. Diameter b. Thickness c. Length d. Diameter and thickness

Last Answer : c. Length

A thin spherical shell under internal pressure will fail under a. Maximum shear stress b. Principal compressive stress c. Principal tensile stress d. None

Description : A thin spherical shell under internal pressure will fail under a. Maximum shear stress b. Principal compressive stress c. Principal tensile stress d. None

Last Answer : c. Principal tensile stress

When a thin cylindrical shell is subjected to an internal pressure, there will be a) a decrease in diameter and length of the shell b) an increase in diameter and length of the shell c) an increase in diameter and decrease in length of the shell d) a decrease in diameter and increase in length of the shell

Description : When a thin cylindrical shell is subjected to an internal pressure, there will be a) a decrease in diameter and length of the shell b) an increase in diameter and length of the shell c) an ... and decrease in length of the shell d) a decrease in diameter and increase in length of the shell

Last Answer : b) an increase in diameter and length of the shell

Design of a thin shell under pressure is done on the basis of a. Radial stress b. Longitudinal stress c. Hoop stress d. All the three stresses

Description : Design of a thin shell under pressure is done on the basis of a. Radial stress b. Longitudinal stress c. Hoop stress d. All the three stresses

Last Answer : c. Hoop stress

The ratio of circumferential stress to the longitudinal stress in the walls of a cylindrical shell, due to flowing liquid, is (A) ½ (B) 1 (C) 1½ (D) 2

Description : The ratio of circumferential stress to the longitudinal stress in the walls of a cylindrical shell, due  to flowing liquid, is  (A) ½  (B) 1  (C) 1½  (D) 2 

Last Answer : (D) 2 

Which welded joint used in the circumferential joint of a cylindrical pressure vessel is (i) Butt joint (ii) Lap joint (iii)Screwed joint (iv) None

Description : Which welded joint used in the circumferential joint of a cylindrical pressure vessel is (i) Butt joint (ii) Lap joint (iii)Screwed joint (iv) None

Last Answer : (ii) Lap joint

Among the cylindrical and spherical thin vessels of same material, diameter and pressure which has the lesser thickness a. Cylindrical shell b. Spherical shell c. Cylindrical shell with semi spherical heads d. None

Description : Among the cylindrical and spherical thin vessels of same material, diameter and pressure which has the lesser thickness a. Cylindrical shell b. Spherical shell c. Cylindrical shell with semi spherical heads d. None

Last Answer : b. Spherical shell

Circumferential welded joint fails by i. Longitudinal stress ii. Radial stress iii. Hoop stress iv. None

Description : Circumferential welded joint fails by i. Longitudinal stress ii. Radial stress iii. Hoop stress iv. None

Last Answer : i. Longitudinal stress

The stress in the wall of a cylinder in a direction normal to its longitudinal axis, due to a force acting along the circumference, is known as (A) Yield stress(B) Longitudinal stress (C) Hoop stress (D) Circumferential stress

Description : The stress in the wall of a cylinder in a direction normal to its longitudinal axis, due to a force  acting along the circumference, is known as  (A) Yield stress  (B) Longitudinal stress  (C) Hoop stress  (D) Circumferential stress 

Last Answer : (C) Hoop stress

In a thick cylindrical shell subjected to an internal pressure (p), the radial stress across the thickness of a cylinder is a) maximum at the outer surface and minimum at the inner surface b) maximum at the inner surface and minimum at the outer surface c) maximum at the inner surface and zero at the outer surface d) maximum at the outer surface and zero at the inner surface

Description : In a thick cylindrical shell subjected to an internal pressure (p), the radial stress across the thickness of a cylinder is a) maximum at the outer surface and minimum at the inner surface b) maximum ... and zero at the outer surface d) maximum at the outer surface and zero at the inner surface

Last Answer : c) maximum at the inner surface and zero at the outer surface

Lame's theory is associated with a) thick cylindrical shells b) thin cylindrical shells c) direct and bending stresses d) none of these

Description : Lame's theory is associated with a) thick cylindrical shells b) thin cylindrical shells c) direct and bending stresses d) none of these

Last Answer : a) thick cylindrical shells

Longitudinal strain in a thin shell is a) σh /E b) σl /E c) σr /E d) None

Description : Longitudinal strain in a thin shell is a) σh /E b) σl /E c) σr /E d) None

Last Answer : d) None

Which stress is the least in a thin shell a. Longitudinal stress b. Hoop stress c. Radial stress d. None

Description : Which stress is the least in a thin shell a. Longitudinal stress b. Hoop stress c. Radial stress d. None

Last Answer : c. Radial stress

A spherical pressure vessel is made of thin magnesium plate 0.25 cm thick. The main diameter of the sphere is 600 cm and allowable stress in tension is 900 kg/cm2. The safe internal gas pressure for the vessel would be a) 0.5 kg/cm2 b) 1.5 kg/cm2 c) 4.5 kg/cm2 d) 5.7 kg/cm2

Description : A spherical pressure vessel is made of thin magnesium plate 0.25 cm thick. The main diameter of the sphere is 600 cm and allowable stress in tension is 900 kg/cm2. The safe internal gas pressure for the vessel would be a) 0.5 kg/cm2 b) 1.5 kg/cm2 c) 4.5 kg/cm2 d) 5.7 kg/cm2

Last Answer : b) 1.5 kg/cm2

Welded joint used in the longitudinal joint of a cylindrical pressure vessel is (i) Butt joint (ii) Lap joint (iii)Screwed joint (iv) None

Description : Welded joint used in the longitudinal joint of a cylindrical pressure vessel is (i) Butt joint (ii) Lap joint (iii)Screwed joint (iv) None

Last Answer : (i) Butt joint

What is the ratio of hoop stresses in a spherical vs cylindrical shell of same diameter, thickness and under same pressure? a. 4:1 b. 2:1 c. 1:2 d. 1:4

Description : What is the ratio of hoop stresses in a spherical vs cylindrical shell of same diameter, thickness and under same pressure? a. 4:1 b. 2:1 c. 1:2 d. 1:4

Last Answer : c. 1:2

A power transmitting ductile material shaft under P, T and M will fail under (a) Tensile considerations only (b) Compressive considerations only (c) Shear considerations only (d) None

Description : A power transmitting ductile material shaft under P, T and M will fail under (a) Tensile considerations only (b) Compressive considerations only (c) Shear considerations only (d) None

Last Answer : (c) Shear considerations only

A thick cylinder under internal fluid pressure’ pi will have maximum stress at the 1. Outer radius 2. Inner radius 3. Mean radius 4. None

Description : A thick cylinder under internal fluid pressure’ pi will have maximum stress at the 1. Outer radius 2. Inner radius 3. Mean radius 4. None

Last Answer : 2. Inner radius

Longitudinal stress in a cylinder is given by [symbols have their usual meanings]. a) PD/2t b) 2PD/t c) PD/4t d) 4PD/t

Description : Longitudinal stress in a cylinder is given by [symbols have their usual meanings]. a) PD/2t b) 2PD/t c) PD/4t d) 4PD/t

Last Answer : c) PD/4t

A member subjected to couple produces rotational motion about its longitudinal axis called as ________ a. torsion b. twisting moment c. both a. and b. d. bending moment

Description : A member subjected to couple produces rotational motion about its longitudinal axis called as ________ a. torsion b. twisting moment c. both a. and b. d. bending moment

Last Answer : c. both a. and b.

When a bar is subjected to a change of temperature and its longitudinal deformation is prevented, the stress induced in the bar is (a) Tensile (b) Compressive (c) Shear (d) Temperature

Description : When a bar is subjected to a change of temperature and its longitudinal deformation is prevented, the stress induced in the bar is (a) Tensile (b) Compressive (c) Shear (d) Temperature

Last Answer : (d) Temperature

When a wire is stretched to double in length, the longitudinal strain produced in it is (a) 0.5 (b) 1.0 (c) 1.5 (d) 2.0

Description : When a wire is stretched to double in length, the longitudinal strain produced in it is (a) 0.5 (b) 1.0 (c) 1.5 (d) 2.0

Last Answer : b) 1.0

Poisson’s ratio is a. Lateral strain / Longitudinal strain b. Shear strain / Lateral strain c. Longitudinal strain / Lateral strain d. Lateral strain / Volumetric strain

Description : Poisson’s ratio is a. Lateral strain / Longitudinal strain b. Shear strain / Lateral strain c. Longitudinal strain / Lateral strain d. Lateral strain / Volumetric strain

Last Answer : a. Lateral strain / Longitudinal strain

As per the Indian boiler regulation (IBR), the type of joint preferred for the circumferential joint is the __________ joint. (A) Butt (B) Lap (C) Welded (D) None of these

Description : As per the Indian boiler regulation (IBR), the type of joint preferred for the circumferential joint is the __________ joint. (A) Butt (B) Lap (C) Welded (D) None of these

Last Answer : (B) Lap

A thick cylinder is subjected to an internal pressure of 60 MPa. If the hoop stress on the outer surface is 150 MPa, then the hoop stress on the internal surface is a) 105 MPa b) 180 MPa c) 210 MPa d) 135 MPa.

Description : A thick cylinder is subjected to an internal pressure of 60 MPa. If the hoop stress on the outer surface is 150 MPa, then the hoop stress on the internal surface is a) 105 MPa b) 180 MPa c) 210 MPa d) 135 MPa.

Last Answer : c) 210 MPa

A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the thickness of the cylinder if it is twice the diameter of the cylinder. a) 12mm b) 4mm c) 8mm d) 16mm

Description : A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the thickness of the cylinder if it is twice the diameter of the cylinder. a) 12mm b) 4mm c) 8mm d) 16mm

Last Answer : c) 8mm

A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder. a) 540mm b) 270mm c) 400mm d) 350mm

Description : A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder. a) 540mm b) 270mm c) 400mm d) 350mm

Last Answer : a) 540mm

Cylinder having inner diameter to wall thickness ratio less than 15 are a) Thin cylinders b) Thick Cylinders c) Moderate cylinders d) none of the above

Description : Cylinder having inner diameter to wall thickness ratio less than 15 are a) Thin cylinders b) Thick Cylinders c) Moderate cylinders d) none of the above

Last Answer : b) Thick Cylinders

In a thin shell which stress is negligible a) σh b) σl c) σr d) None

Description : In a thin shell which stress is negligible a) σh b) σl c) σr d) None

Last Answer : c) σr

Value of σr in a thin shell is a) pD/2t b) pD/4t c) pD/3t d) None

Description : Value of σr in a thin shell is a) pD/2t b) pD/4t c) pD/3t d) None

Last Answer : d) None

Hoop strain in a thin shell is a) σh /E b) σl /E c) 3 σh /E d) None

Description : Hoop strain in a thin shell is a) σh /E b) σl /E c) 3 σh /E d) None

Last Answer : d) None

Which one is most important in a thin shell? a) d/t <20 b) d/t> 10 c) Stresses are uniform d) None

Description : Which one is most important in a thin shell? a) d/t 10 c) Stresses are uniform d) None

Last Answer : c) Stresses are uniform

Which is most predominant type of failure in a thin shell? a. Bearing failure b. Compression failure c. Crushing failure d. None

Description : Which is most predominant type of failure in a thin shell? a. Bearing failure b. Compression failure c. Crushing failure d. None

Last Answer : d. None

Radial stress in a thin shell is given by a. pD/2t b. pD/4t c. pD/3t d. None

Description : Radial stress in a thin shell is given by a. pD/2t b. pD/4t c. pD/3t d. None

Last Answer : d. None

Hoop stress in a thin vessel is a. pD/2t b. pD/4t c. pD/3t d. None

Description : Hoop stress in a thin vessel is a. pD/2t b. pD/4t c. pD/3t d. None

Last Answer : a. pD/2t

Vessel is said to be thin if a. D/t =20 b. D/t=10 c. D/t >20 d. D/t >10

Description : Vessel is said to be thin if a. D/t =20 b. D/t=10 c. D/t >20 d. D/t >10

Last Answer : c. D/t >20

A vessel is said to be thin if a. Its wall has less thickness b. Stresses are uniform over the entire thickness c. Stresses vary at inner and at outer radius d. None of the above

Description : A vessel is said to be thin if a. Its wall has less thickness b. Stresses are uniform over the entire thickness c. Stresses vary at inner and at outer radius d. None of the above

Last Answer : b. Stresses are uniform over the entire thickness

The property of a material by which it can be beaten or rolled into thin sheets, is called (a) Elasticity (b) Plasticity (c) Ductility (d) Malleability

Description : The property of a material by which it can be beaten or rolled into thin sheets, is called (a) Elasticity (b) Plasticity (c) Ductility (d) Malleability

Last Answer : (d) Malleability

In moment distribution method any unbalanced moment at a joint is a. neglected b. multiplied by a factor to solve c. distributed in the spans d.considered infinite

Description : In moment distribution method any unbalanced moment at a joint is a. neglected b. multiplied by a factor to solve c. distributed in the spans d.considered infinite

Last Answer : c. distributed in the spans

Effect of applied moment at a joint on the other joints is known as the a.carry in factor b. carry over factor c.carry up factor d.carry down factor

Description : Effect of applied moment at a joint on the other joints is known as the a.carry in factor b. carry over factor c.carry up factor d.carry down factor

Last Answer : b. carry over factor

The strain energy will be higher in which shaft under the same torque (a) Solid shaft (b) Hollow shaft (c) Same in Solid as well as hollow shaft (d) None

Description : The strain energy will be higher in which shaft under the same torque (a) Solid shaft (b) Hollow shaft (c) Same in Solid as well as hollow shaft (d) None

Last Answer : (b) Hollow shaft

Lap welded joints used in circumferential joints because of ? i. High strength requirements ii. Low strength requirements iii. Low as well as high strength requirements

Description : Lap welded joints used in circumferential joints because of ? i. High strength requirements ii. Low strength requirements iii. Low as well as high strength requirements

Last Answer : ii. Low strength requirements

The clips placed at intervals along some leaf spring to prevent spring leaf separation on rebound are (a) rebound clips (b) separation clips (c) interval clips (d)relief clips

Description : The clips placed at intervals along some leaf spring to prevent spring leaf separation on rebound are (a) rebound clips (b) separation clips (c) interval clips (d)relief clips

Last Answer : (a) rebound clips

In a fixed beam the total change of slope along the span is a. Zero b.infinite c. neglected d.assumed to be unit value

Description : In a fixed beam the total change of slope along the span is a. Zero b.infinite c. neglected d.assumed to be unit value

Last Answer : a. Zero

A shaft of length L is subject to a constant twisting moment T along its length L, then angle q through which one end of the bar will twist relative to other will be (a) T/g (b) T/GJ (c) GJ/TL (d) TL/GJ

Description : A shaft of length L is subject to a constant twisting moment T along its length L, then angle q through which one end of the bar will twist relative to other will be (a) T/g (b) T/GJ (c) GJ/TL (d) TL/GJ

Last Answer : (d) TL/GJ

Which of the following assumptions are made in torsion theory? a. Shaft is perfectly straight b. Material of the shaft is heterogeneous c. Twist cannot be uniform along the length of the shaft d. Shaft is perfectly curve

Description : Which of the following assumptions are made in torsion theory? a. Shaft is perfectly straight b. Material of the shaft is heterogeneous c. Twist cannot be uniform along the length of the shaft d. Shaft is perfectly curve v

Last Answer : a. Shaft is perfectly straight b. Material of the shaft is heterogeneous

What is the shear stress acting along the neutral axis, over a triangular section? a. 2.66 (S/bh) b. 1.5 (S/bh) c. 0.375 (S/bh) d. None of the above

Description : What is the shear stress acting along the neutral axis, over a triangular section? a. 2.66 (S/bh) b. 1.5 (S/bh) c. 0.375 (S/bh) d. None of the above

Last Answer : a. 2.66 (S/bh)

What is the shear stress acting along the neutral axis of triangular beam section, with base 60 mm and height 150 mm, when shear force of 30 kN acts? a. 15.36 N/mm2 b. 10.6 N/mm2 c. 8.88 N/mm2 d. Insufficient data

Description : What is the shear stress acting along the neutral axis of triangular beam section, with base 60 mm and height 150 mm, when shear force of 30 kN acts? a. 15.36 N/mm2 b. 10.6 N/mm2 c. 8.88 N/mm2 d. Insufficient data

Last Answer : c. 8.88 N/mm2