Description : Two close-coiled helical springs are equal in all respects except the number of turns. If the number of turns are in the ratio of 2:3, then the stiffness of the spring will be in the ratio of (a) 2:3 (b) 4:9 (c) 3:2 (d) 9:4
Last Answer : (c) 3:2
Description : Most important features of any spring are (a) Deflection, stiffness and strength (b) Stiffness, bending and shear strengths (c) Strain energy, deflection and strength (d) None
Last Answer : (c) Strain energy, deflection and strength
Description : The load required to produce a unit deflection in the spring is called (a) Modulus of Rigidity (b) Spring stiffness (c) Flexural rigidity (d) Tensional rigidity
Last Answer : b) Spring stiffness
Description : A spring of stiffness 100 N/mm used in a spring-loaded safety valve of diameter 20 mm on a boiler with the pressure inside the boiler equal to 1 MPa should be initially compressed by a. 5mm b. 3.14 mm c. 2mm d. 6.28 mm
Last Answer : b. 3.14 mm
Description : A spring with 25 active coils cannot be accommodated within a given space. Hence 5 coils of the spring are cut. The stiffness of the new spring will be a. the same b. 1.25 times the original spring c. 0.8 times the original spring d. 20 times the original spring
Last Answer : b. 1.25 times the original spring
Description : Stiffness of the spring can be increased by a. increase the number of turns b. increase the free length c. decrease the number of turns d. decrease the spring wire diameter
Last Answer : c. decrease the number
Description : A compression spring is made of music wire of 2 mm diameter having a shear strength and shear modulus of 800 Mpa and 80 Gpa respectively. The mean coil diameter is 20mm, free length is 40 mm, and the number ... by 8 times b. decreased by 2 times c. increased by 2 times d. decreased by 8 times
Last Answer : a. increased by 8 times
Description : A spring is designed for (a) Higher strength (b) Higher deflection (c) Higher stiffness (d) None
Last Answer : (b) Higher deflection
Description : Determine number of coils in a helical compression spring, if modulus of rigidity is 80 Gpa and spring stiffness is 50 N/ mm. Assume wire diameter and spring index as 8 mm and 5 respectively a. 11.8 turns b. 12.8 turns c. 13.3 turns d. None of the above
Last Answer : b. 12.8 turns
Description : If a close-coiled helical spring absorbs 50 N-mm of energy while extending by 5 mm, its stiffness will be (a) 2 N/mm (b) 4 N/mm (c) 6 N/mm (d) 10 N/mm
Last Answer : (d) 10 N/mm
Description : A close-coiled helical spring of stiffness 30 N/mm is arranged in series with another such spring of stiffness 60 N/mm. The stiffness of composite unit is (a) 20 N/mm (b) 30 N/mm (c) 45 N/mm (d) 90 N/mm
Last Answer : (a) 20 N/mm
Description : A close –coiled helical spring is cut into two equal parts. The stiffness of the resulting springs will be (a) same (b) double (c) half (d) One-fourth
Last Answer : (b) double
Last Answer : (b) Spring stiffness
Description : Springs with rectangular or square cross section used for a. higher stiffness b. larger volume c. larger length d. smaller length
Last Answer : b. larger volume
Description : Two concentric springs with stiffness equal to 100 N/mm and 80 N/mm respectively, when subjected to load of 900N will deflect by a. 9mm b. 11.25 mm c. 5mm d. 31.5 mm
Last Answer : c. 5mm
Description : Pure Buckling uses the equation of (a) Rankin-Gordon (b) Euler (c) Stiffness (d) None
Last Answer : (b) Euler
Description : The stiffness of solid shaft is---------- than the stiffness of hollow shaft with same weight. a) less b) more c) equal d) not equal
Last Answer : b) more
Description : A shaft is designed for (a) Strength alone (b) Stiffness alone (c) Both for strength and stiffness (d) None
Last Answer : (c) Both for strength and stiffness
Description : The close-coiled helical springs ‘A’ and ‘B’ are of same material, same coil diameter, same wire diameter and subjected to same load. If the number of turns of spring ‘A’ is half that of spring ‘B’, the ratio of deflection of spring ‘A’ to spring ‘B’ is (a)1/2 (b) 1 (c) 2 (d) 4
Last Answer : (a)1/2
Description : A block of weight 20 kg slides with an initial velocity of 2 m sec down an inclined plane on to a spring of stiffness 10 kg/cm. If the co--efficient of friction is 0.2, angle ? = 30 the ratio of ... be a.More than one b.One c.Less than one d.Depends on the stiffness of spring e.None of the above
Last Answer : a. More than one
Description : The stiffness of spring is, (A) Deflection per unit of axial force (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection
Last Answer : (D) Force required to produce unit deflection
Description : The capacity of a spring to store energy is called the spring form co-efficient. Stiffness of a spring is measured by the (A) Ability to absorb shock (B) Capacity to store energy (C) Ratio of the wire & coil diameters (D) Load to produce unit deflection
Last Answer : Option D
Description : In case of a laminated spring, the load at which the plates become straight is called (a) working load (b) safe load (c) proof load (d) none
Last Answer : (c) proof load
Description : The type of spring used to achieve any linear and non-linear load-deflection characteristics is (a)spiral spring (b) non-ferrous spring (c)Belleville spring (d) torsion spring
Last Answer : (c)Belleville spring
Description : The type of spring used to achieve greater load carrying capacity within given space is (a)spiral spring (b) springs in series (c)multi-leaf spring (d) concentric spring
Last Answer : (d) concentric spring
Description : With a leaf spring type of suspension, interference between steering and suspension system can be (a) front end of the spring is pin joined and the rear end is shackled (b) front end of the spring is ... joined (c) both end of the spring are shackled (d) both end of the spring are pin joined
Last Answer : (b) front end of the spring is shackled and the rear end is pin joined
Description : The clips placed at intervals along some leaf spring to prevent spring leaf separation on rebound are (a) rebound clips (b) separation clips (c) interval clips (d)relief clips
Last Answer : (a) rebound clips
Description : The laminated spring which is in common use, is of the type (a) full elliptic (b) semi elliptic (c)one quarter elliptic (d)three quarter elliptic
Last Answer : (b) semi elliptic
Description : The device that permits variation in the distance between the spring eyes of a leaf spring as the spring flexes is called (a) Spring shackle (b) spring U bolt (c) spring hanger (d) spring leaf
Last Answer : (a) Spring shackle
Description : Leaf spring for vehicles are nipped to (a) To vary the effective length of the spring (b) to increase the interleaf friction (c) Improve the load carrying capacity of spring (d) ensure that all leaves are uniformly stressed during loading
Last Answer : (d) ensure that all leaves are uniformly stressed during loading
Description : The weight or pressure required to deflect a spring in mm is called the spring (a) Weight (b) deflection (c) rate (d) rebound
Last Answer : c) rate
Description : There are number of laminations in a (a) Close coiled spring (b) Open coiled spring (c) Spiral spring (d) None
Last Answer : (d) None
Description : Spiral spring is quite rigid. (a) Yes (b) No it is flexible (c) It is of moderate rigidity (d) Rigidity can’t be determined
Last Answer : (b) No it is flexible
Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. (a) Fatigue Failure (b) Fracture (c) None of the listed (d) Nipping
Last Answer : (a) Fatigue Failure
Description : A concentric spring consists of 2 sprigs of diameter 10mm and 4mm. The net force acting on the composite spring is 5000N. Find the force acting on each of the two springs. (a) 1232.2N and 3767.8N (b) 786.4N and 4213.6N (c) 689.7N and 4310.3N (d) 645.3N and 4354.7N
Last Answer : (c) 689.7N and 4310.3N
Description : The strain energy stored in a spiral spring is given by? (a) 12M²L/Ebtᵌ (b) 6M²L/Ebtᵌ (c) 8M²L/Ebtᵌ (d) None of the listed
Last Answer : (b) 6M²L/Ebtᵌ
Description : Belleville spring can only produce linear load deflection characteristics. (a) Only linear (b) Linear as well as non linear (c) Non-linear (d) None of the mentioned
Last Answer : (b) Linear as well as non linear
Description : A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the ... close the nip. (a) 4332.2N (b) 4674.1N (c) 4985.4N (d) Can't be determined
Last Answer : (b) 4674.1N
Description : A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the ... /mm², calculate the initial nip. (a) 26.8mm (b) 24.9mm (c) 22.5mm (d)23.1mm
Last Answer : b) 24.9mm
Description : Spring shackles are used to join (a) chassis frame and spring (b) Spring and Axle (c) chassis frame and axle (d) all of the above
Last Answer : (a) chassis frame and spring
Description : Shackles are sort of (a) coupling (b) link (c) spring (d) none of the above
Last Answer : (b) link
Description : The spring used in mechanical toys is (a) Leaf spring (b) Spiral spring (c) Helical spring (d) All of these
Last Answer : (b) Spiral spring
Description : A spring used to absorb shocks and vibrations is (a) Close-coil helical spring (b) Open coiled helical spring (c) Spiral spring (d) Leaf spring
Last Answer : (d) Leaf spring
Description : In a watch, the spring is used to store energy. The energy is released (a) To stop the watch (b) To run the watch (c) To change the time (d) All of these (
Last Answer : (b) To run the watch
Description : The most important property for the spring material is (a) High elastic limit (b) High deflection value (c) Resistance to fatigue and shock (d) All of these
Last Answer : (d) All of these
Description : In spring balances, the spring is used (a) To apply forces (b) To absorb shocks (c) To store strain energy (d) To measure forces
Last Answer : (d) To measure forces
Description : Deflection in a spring should be (a) Large (b) Small (c) Zero (d) None
Last Answer : (a) Large
Description : Strain energy in a spring should be (a) Large (b) Small (c) Zero (d) None
Description : Spring is an (a) Elastic device (b) Plastic device (c) Elastic as well as plastic device (d) None
Last Answer : (a) Elastic device