Find the shear stress in the spring wire used to design a helical compression sprig if a load of 1200N is applied on the spring. Spring index is 6, and wire diameter 7mm. a) 452.2N/mm² b) 468.6N/mm² c) 512.2N/mm² d) None of the listed

Find the shear stress in the spring wire used to design a helical compression sprig if a load of  1200N is applied on the spring. Spring index is 6, and wire diameter 7mm. a) 452.2N/mm²
b) 468.6N/mm²
c) 512.2N/mm²
d) None of the listed
by

1 Answer

Answer :

b) 468.6N/mm²
by

Related questions

Find total number coils in a spring having square and ground ends. Deflection in the spring is 6mm when load of 1100N is applied. Modulus of rigidity is 81370N/mm². Wire diameter and pitch circle diameter are 10mm and 50mm respectively. a) 7 b) 6 c) 5 d) 4

Description : Find total number coils in a spring having square and ground ends. Deflection in the spring is 6mm when load of 1100N is applied. Modulus of rigidity is 81370N/mm². Wire diameter and pitch circle diameter are 10mm and 50mm respectively. a) 7 b) 6 c) 5 d) 4

Last Answer : a) 7

Determine number of coils in a helical compression spring, if modulus of rigidity is 80 Gpa and spring stiffness is 50 N/ mm. Assume wire diameter and spring index as 8 mm and 5 respectively a. 11.8 turns b. 12.8 turns c. 13.3 turns d. None of the above

Description : Determine number of coils in a helical compression spring, if modulus of rigidity is 80 Gpa and spring stiffness is 50 N/ mm. Assume wire diameter and spring index as 8 mm and 5 respectively a. 11.8 turns b. 12.8 turns c. 13.3 turns d. None of the above

Last Answer : b. 12.8 turns

A concentric spring consists of 2 sprigs of diameter 10mm and 4mm. The net force acting on the composite spring is 5000N. Find the force acting on each of the two springs. (a) 1232.2N and 3767.8N (b) 786.4N and 4213.6N (c) 689.7N and 4310.3N (d) 645.3N and 4354.7N

Description : A concentric spring consists of 2 sprigs of diameter 10mm and 4mm. The net force acting on the composite spring is 5000N. Find the force acting on each of the two springs. (a) 1232.2N and 3767.8N (b) 786.4N and 4213.6N (c) 689.7N and 4310.3N (d) 645.3N and 4354.7N

Last Answer : (c) 689.7N and 4310.3N

Determine the maximum shearing stress and elongation in a helical steel spring composed of 20 turns of 20-mm-diameter wire on a mean radius of 90 mm when the spring is supporting a load of 1.5 kN. and G = 83 GPa. a. 200 mm b. 105.4 mm c. 150 mm d. 250 mm

Description : Determine the maximum shearing stress and elongation in a helical steel spring composed of 20 turns of 20-mm-diameter wire on a mean radius of 90 mm when the spring is supporting a load of 1.5 kN. and G = 83 GPa. a. 200 mm b. 105.4 mm c. 150 mm d. 250 mm

Last Answer : b. 105.4 mm

A close coiled helical spring is compressed. Its wire is subjected to A. Compression B. Tension C.Shear D. Torque

Description : A close coiled helical spring is compressed. Its wire is subjected to A. Compression B. Tension C.Shear D. Torque

Last Answer : B. Tension

The spring constant of a helical compression spring does not depend on a. Coil diameter b. Material strength c. Number of active turns d. wire diameter

Description : The spring constant of a helical compression spring does not depend on a. Coil diameter b. Material strength c. Number of active turns d. wire diameter

Last Answer : b. Material strength

A closed helical spring under axial load is designed on the basis of (a) Shear (b) Compression (c) Bending (d) None

Description : A closed helical spring under axial load is designed on the basis of (a) Shear (b) Compression (c) Bending (d) None

Last Answer : (a) Shear

A helical spring is fabricated by wrapping wire 19.05 mm in diameter around a forming cylinder 203.2 mm in diameter. Compute the number of turns required to permit an elongation of 101.6 mm. without exceeding a shearing stress of 124 N/mm2. G = 82737 N/mm2. a. 10 turns b. 20 turns c. 25 turns d. 30 turns

Description : A helical spring is fabricated by wrapping wire 19.05 mm in diameter around a forming cylinder 203.2 mm in diameter. Compute the number of turns required to permit an elongation of 101.6 mm. without exceeding a shearing ... G = 82737 N/mm2. a. 10 turns b. 20 turns c. 25 turns d. 30 turns

Last Answer : a. 10 turns

The piston rod of a hydraulic cylinder exerts an operating force of 10kN. The allowable stress in the cylinder is 45N/mm². Calculate the thickness of the cylinder using Lame’s equation. Diameter of the cylinder is 40mm and pressure in cylinder is 10MPa. a) 2.05mm b) 4.2mm c) 5.07mm d) None of the listed

Description : The piston rod of a hydraulic cylinder exerts an operating force of 10kN. The allowable stress in the cylinder is 45N/mm². Calculate the thickness of the cylinder using Lame's equation. Diameter of the cylinder is 40mm and ... is 10MPa. a) 2.05mm b) 4.2mm c) 5.07mm d) None of the listed

Last Answer : c) 5.07mm

When two helical springs of equal lengths are arranged to form a cluster spring, then a. Shear stress in each spring will be equal b. Load taken by each spring will be half the total load c. Only A is correct d. Both A and B is correct

Description : When two helical springs of equal lengths are arranged to form a cluster spring, then a. Shear stress in each spring will be equal b. Load taken by each spring will be half the total load c. Only A is correct d. Both A and B is correct

Last Answer : d. Both A and B is correct

The close-coiled helical springs ‘A’ and ‘B’ are of same material, same coil diameter, same wire diameter and subjected to same load. If the number of turns of spring ‘A’ is half that of spring ‘B’, the ratio of deflection of spring ‘A’ to spring ‘B’ is (a)1/2 (b) 1 (c) 2 (d) 4

Description : The close-coiled helical springs ‘A’ and ‘B’ are of same material, same coil diameter, same wire diameter and subjected to same load. If the number of turns of spring ‘A’ is half that of spring ‘B’, the ratio of deflection of spring ‘A’ to spring ‘B’ is (a)1/2 (b) 1 (c) 2 (d) 4

Last Answer : (a)1/2

For a helical torsion sprig, the stress concentration factor at outer fibre is? Give spring index=5. a) 0.78 b) 0.87 c) 1.87 d) 0.69

Description : For a helical torsion sprig, the stress concentration factor at outer fibre is? Give spring index=5. a) 0.78 b) 0.87 c) 1.87 d) 0.69

Last Answer : b) 0.87

For a helical torsion sprig, the stress concentration factor at inner fibre is? Give spring index=5. a) 1.005 b) 1.175 c) 1.223 d) 1.545

Description : For a helical torsion sprig, the stress concentration factor at inner fibre is? Give spring index=5. a) 1.005 b) 1.175 c) 1.223 d) 1.545

Last Answer : b) 1.175

A compression spring is made of music wire of 2 mm diameter having a shear strength and shear modulus of 800 Mpa and 80 Gpa respectively. The mean coil diameter is 20mm, free length is 40 mm, and the number of active coils is 10. If the mean coil diameter is reduced to 10 mm, the stiffness of the spring is approximately a. increased by 8 times b. decreased by 2 times c. increased by 2 times d. decreased by 8 times

Description : A compression spring is made of music wire of 2 mm diameter having a shear strength and shear modulus of 800 Mpa and 80 Gpa respectively. The mean coil diameter is 20mm, free length is 40 mm, and the number ... by 8 times b. decreased by 2 times c. increased by 2 times d. decreased by 8 times

Last Answer : a. increased by 8 times

A open helical spring under axial torque is designed on the basis of (a) Shear (b) Compression (c) Bending (d) None

Description : A open helical spring under axial torque is designed on the basis of (a) Shear (b) Compression (c) Bending (d) None

Last Answer : d) None

A closed helical spring under axial torque is designed on the basis of (a) Shear (b) Compression (c) Bending (d) None

Description : A closed helical spring under axial torque is designed on the basis of (a) Shear (b) Compression (c) Bending (d) None

Last Answer : (c) Bending

When the helical compression spring is subjected to axial compressive force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Description : When the helical compression spring is subjected to axial compressive force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Last Answer : (D) Torsional shear stress

The type of stress induced in a closed coiled helical tension spring is a. tensile b. compressive c. torsional shear d. tensile and compressive

Description : The type of stress induced in a closed coiled helical tension spring is a. tensile b. compressive c. torsional shear d. tensile and compressive

Last Answer : c. torsional shear

Shear stress in a close coiled helical spring is (a) 16WD/π d3 (b) 32WD/π d3 (c) 8WD/π d3 (d) None

Description : Shear stress in a close coiled helical spring is (a) 16WD/π d3 (b) 32WD/π d3 (c) 8WD/π d3 (d) None

Last Answer : (c) 8WD/π d3

Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm². a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm

Description : Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm². a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm

Last Answer : b) 41.2mm

In a square and ground helical spring the effective number of turns is incresead by a. 1 b. 2 c. 1.5 d. 0 Ans: b 77. Frequency of the fluctuating load of helical compression spring should be a. lees than natural frequency of vibration b. twenty times the natural frequency of vibration c. slightly greater than the natural frequency d. twenty times less than the natural frequency of vibration

Description : In a square and ground helical spring the effective number of turns is incresead by a. 1 b. 2 c. 1.5 d. 0 Ans: b 77. Frequency of the fluctuating load of helical compression ... vibration c. slightly greater than the natural frequency d. twenty times less than the natural frequency of vibration

Last Answer : d. twenty times less than the natural frequency of vibration

When a close-coiled helical spring is subjected to an axial load, it is said to be under. (a) Bending (b) Shear (c) Torsion (d) Crushing

Description : When a close-coiled helical spring is subjected to an axial load, it is said to be under. (a) Bending (b) Shear (c) Torsion (d) Crushing

Last Answer : (c) Torsion

If yielding strength=400N/mm², the find the permissible shear stress according to ASME standards. a) 72 N/mm² b) 76 N/mm² c) 268 N/mm² d) 422 N/mm²

Description : If yielding strength=400N/mm², the find the permissible shear stress according to ASME standards. a) 72 N/mm² b) 76 N/mm² c) 268 N/mm² d) 422 N/mm²

Last Answer : a) 72 N/mm²

A railway wagon moving with a speed of 1.5m/s is brought to rest by bumper consisting of two springs. Mass of wagon is 100kg. The springs are compressed by 125mm. Calculate the maximum force acting on each spring. a) 1200N b) 1500N c) 1800N d) 2000N

Description : A railway wagon moving with a speed of 1.5m/s is brought to rest by bumper consisting of two springs. Mass of wagon is 100kg. The springs are compressed by 125mm. Calculate the maximum force acting on each spring. a) 1200N b) 1500N c) 1800N d) 2000N

Last Answer : c) 1800N

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Last Answer : b) 25.8N/mm2

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Last Answer : b) 25.8N/mm2

Pick out the wrong statement. (A) The equivalent stiffness of two springs (of equal stiffness 'S') in series is S/2 while in parallel is 2S (B) For a helical spring, deflection is proportional to D3(D = mean coil diameter) or d4(d = wire diameter) (C) Crushing load or columns is less than the buckling load (D) Modulus of resilience is proportional to (stress at elastic limit)2

Description : Pick out the wrong statement. (A) The equivalent stiffness of two springs (of equal stiffness 'S') in series is S/2 while in parallel is 2S (B) For a helical spring, deflection is ... is less than the buckling load (D) Modulus of resilience is proportional to (stress at elastic limit)2

Last Answer : (C) Crushing load or columns is less than the buckling load

A hollow shaft has an inner diameter of 3.7 cm and an outer diameter of 4.0 cm. A 1 kN-m torque is applied to this shaft. What is the shear stress at the mid-radius of this shaft? (a) 117Mpa (b) 178 Mpa (c) 286 Mpa (d) 363 Mpa

Description : A hollow shaft has an inner diameter of 3.7 cm and an outer diameter of 4.0 cm. A 1 kN-m torque is applied to this shaft. What is the shear stress at the mid-radius of this shaft? (a) 117Mpa (b) 178 Mpa (c) 286 Mpa (d) 363 Mpa

Last Answer : (c) 286 Mpa

Wahl’s stress concentration factor is used in close coiled springs under axial load to account for (a) Shear effect (b) Bending effect (c) Compression effect (d) none

Description : Wahl’s stress concentration factor is used in close coiled springs under axial load to account for (a) Shear effect (b) Bending effect (c) Compression effect (d) none

Last Answer : (b) Bending effect

Compute the maximum shearing stress developed in a phosphor bronze spring having mean diameter of 200 mm and consisting of 24 turns of 20-mm diameter wire when the spring is stretched 100 mm. and G = 42 GPa. a. 51 MPa b. 31.89 MPa c. 80 MPa d. 70 MPa

Description : Compute the maximum shearing stress developed in a phosphor bronze spring having mean diameter of 200 mm and consisting of 24 turns of 20-mm diameter wire when the spring is stretched 100 mm. and G = 42 GPa. a. 51 MPa b. 31.89 MPa c. 80 MPa d. 70 MPa

Last Answer : b. 31.89 MPa

A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the leaves are 100mm and 12mm respectively. Calculate the initial pre load required to close the nip. (a) 4332.2N (b) 4674.1N (c) 4985.4N (d) Can’t be determined

Description : A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the ... close the nip. (a) 4332.2N (b) 4674.1N (c) 4985.4N (d) Can't be determined

Last Answer : (b) 4674.1N

A short, hollow cast iron cylinder with a wall thickness of 1 cm is to carry a compressive load of 10 tonnes. If the working stress in compression is 800 kg/cm2, the outside diameter of the cylinder should not be less than a) 0.5cm b) 5 cm c) 2.5cm d) 4.5 cm

Description : A short, hollow cast iron cylinder with a wall thickness of 1 cm is to carry a compressive load of 10 tonnes. If the working stress in compression is 800 kg/cm2, the outside diameter of the cylinder should not be less than a) 0.5cm b) 5 cm c) 2.5cm d) 4.5 cm

Last Answer : b) 5 cm

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed

Last Answer : b) 51.6N/mm2

When the helical torsion spring is subjected to torque, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Description : When the helical torsion spring is subjected to torque, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Last Answer : (C) Bending stress

When the helical extension spring is subjected to axial tensile force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Description : When the helical extension spring is subjected to axial tensile force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Last Answer : (D) Torsional shear stress

For keeping the stress wholly compressive the load may be applied on a circular column anywherewithin a concentric circle of diameter (a) d/2 (b) d/3 (c) d/4 (d) d/8

Description : For keeping the stress wholly compressive the load may be applied on a circular column anywherewithin a concentric circle of diameter (a) d/2 (b) d/3 (c) d/4 (d) d/8

Last Answer : (c) d/4

A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the leaves are 100mm and 12mm respectively. If modulus of elasticity is 207000N/mm², calculate the initial nip. (a) 26.8mm (b) 24.9mm (c) 22.5mm (d)23.1mm

Description : A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the ... /mm², calculate the initial nip. (a) 26.8mm (b) 24.9mm (c) 22.5mm (d)23.1mm

Last Answer : b) 24.9mm

A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the thickness of the cylinder if it is twice the diameter of the cylinder. a) 12mm b) 4mm c) 8mm d) 16mm

Description : A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the thickness of the cylinder if it is twice the diameter of the cylinder. a) 12mm b) 4mm c) 8mm d) 16mm

Last Answer : c) 8mm

A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder. a) 540mm b) 270mm c) 400mm d) 350mm

Description : A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder. a) 540mm b) 270mm c) 400mm d) 350mm

Last Answer : a) 540mm

A carriage spring is designed on the basis of (a) Shear (b) Compression (c) Bending (d) None

Description : A carriage spring is designed on the basis of (a) Shear (b) Compression (c) Bending (d) None

Last Answer : (c) Bending

A hollow circular tube with a 2.3-cm I.D. and 2.5-cm O.D. is rigidly supported at its ends. A 2.5 kN-m torque is applied at the center of this tube. What is the maximum shear stress acting on this tube? (a) 2.87Mpa (b) 4.27 Mpa (c) 6.92 Mpa (d) 10.2 Mpa

Description : A hollow circular tube with a 2.3-cm I.D. and 2.5-cm O.D. is rigidly supported at its ends. A 2.5 kN-m torque is applied at the center of this tube. What is the maximum shear stress acting on this tube? (a) 2.87Mpa (b) 4.27 Mpa (c) 6.92 Mpa (d) 10.2 Mpa

Last Answer : (a) 2.87Mpa

What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. (a) Fatigue Failure (b) Fracture (c) None of the listed (d) Nipping

Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. (a) Fatigue Failure (b) Fracture (c) None of the listed (d) Nipping

Last Answer : (a) Fatigue Failure

If a close-coiled helical spring absorbs 50 N-mm of energy while extending by 5 mm, its stiffness will be (a) 2 N/mm (b) 4 N/mm (c) 6 N/mm (d) 10 N/mm

Description : If a close-coiled helical spring absorbs 50 N-mm of energy while extending by 5 mm, its stiffness will be (a) 2 N/mm (b) 4 N/mm (c) 6 N/mm (d) 10 N/mm

Last Answer : (d) 10 N/mm

Magnitude of shear stress induced in a shaft due to applied torque varies from a. Maximum at centre to zero at circumference. b. Maximum at centre to minimum (not-zero) at circumference. c. Zero at centre to maximum at circumference. d. Minimum (not zero) at centre to maximum at circumference.

Description : Magnitude of shear stress induced in a shaft due to applied torque varies from a. Maximum at centre to zero at circumference. b. Maximum at centre to minimum (not-zero) at circumference. c. Zero at centre to maximum at circumference. d. Minimum (not zero) at centre to maximum at circumference.

Last Answer : c. Zero at centre to maximum at circumference.

Overlap in a leaf spring is (a) L/n (b) L/2n (c) L/3n (d) None

Description : Overlap in a leaf spring is (a) L/n (b) L/2n (c) L/3n (d) None

Last Answer : (b) L/2n

Stiffness of the spring can be increased by a. increase the number of turns b. increase the free length c. decrease the number of turns d. decrease the spring wire diameter

Description : Stiffness of the spring can be increased by a. increase the number of turns b. increase the free length c. decrease the number of turns d. decrease the spring wire diameter

Last Answer : c. decrease the number

A solid shaft has diameter 80 mm. It is subjected to a torque of 4 KNm. The maximum shear stress induced in the shaft would be (a) 75/p N/mm2 (b) 250/p N/mm2 (c) 125/p N/mm2 (d) 150/p N/mm2

Description : A solid shaft has diameter 80 mm. It is subjected to a torque of 4 KNm. The maximum shear stress induced in the shaft would be (a) 75/p N/mm2 (b) 250/p N/mm2 (c) 125/p N/mm2 (d) 150/p N/mm2

Last Answer : (c) 125/p N/mm2

Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm

Description : Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm

Last Answer : c. 587.1 mm

What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2

Description : What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2

Last Answer : b. 14.69 N/mm2

What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2

Description : What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2

Last Answer : c. 20.120 N/mm2