In induction type directional over current relay the driving torque is due to interaction of magnetic fields

In induction type directional over current relay the driving torque is due to interaction of magnetic fields derived from

(A) current in the potential coil

(B) both voltage and current in the relay windings

(C) directional element and non-directional element

(D) non-directional element and the trip circuit
by

1 Answer

Answer :

In induction type directional over current relay the driving torque is due to interaction of magnetic fields derived from directional element and non-directional element

by

Related questions

Explain construction and operation of induction type directional over current relay.

Description : Explain construction and operation of induction type directional over current relay.

Last Answer : Directional overcurrent relay: Construction: It consists of two units: i) Non-directional Over-current unit ii) Directional power unit The directional unit consists of upper electromagnet ... closes the trip circuit. This operates circuit breaker which isolates the faulty section. 

In the induction type directional over current relay, when a short-circuit occurs in the circuit

Description : In the induction type directional over current relay, when a short-circuit occurs in the circuit (A) power flows in reverse direction (B) power flows in normal direction (C) directional power element does not operate (D) over current element is not energized

Last Answer : In the induction type directional over current relay, when a short-circuit occurs in the circuit power flows in reverse direction

If the phase -angle of the voltage coil of a directional relay is 50°, the maximum torque angle of the relay is:

Description : If the phase -angle of the voltage coil of a directional relay is 50°, the maximum torque angle of the relay is: (A) 130° (B) 100° (C) 50° (D) 25°

Last Answer : If the phase -angle of the voltage coil of a directional relay is 50°, the maximum torque angle of the relay is: 50°

Purpose of Directional inverse Over current & earth fault relay; type- CDD

Description : Purpose of Directional inverse Over current & earth fault relay; type- CDD

Last Answer : Directional phase or earth fault protection of ring-mains, parallel transformers, transformer feeders, parallel feeders etc., employing the time graded principle.; This relay comprises an inductive ... induction disc unit. The directional unit is normally provided with voltage polarising coils. 

In a three-phase, squirrel-cage type, induction motor the rotating magnetic field is established by the _____________. A. current induced in the rotor windings B. application of a three-phase voltage supply to the stator windings C. laminated steel core and aluminum conductors in the rotor D. interaction of the magnetic field caused by the induced current in the squirrel-cage bars with the magnetic field of the stator

Description : In a three-phase, squirrel-cage type, induction motor the rotating magnetic field is established by the _____________. A. current induced in the rotor windings B. application of a three-phase voltage ... caused by the induced current in the squirrel-cage bars with the magnetic field of the stator

Last Answer : Answer: B

The operating torque of the upper induction disc-type element, or timer element, of an AC reverse power relay is obtained from ____________. A. the main bus B. a separate battery source C. line voltage D. electromagnets

Description : The operating torque of the upper induction disc-type element, or timer element, of an AC reverse power relay is obtained from ____________. A. the main bus B. a separate battery source C. line voltage D. electromagnets

Last Answer : Answer: D

The most efficient torque — producing actuating structure for induction — type relay is:

Description : The most efficient torque — producing actuating structure for induction — type relay is:

Last Answer : The most efficient torque — producing actuating structure for induction — type relay is: induction-cup structure

The torque produced in induction type relay (shaded pole structure) is?

Last Answer : The torque produced in induction type relay (shaded pole structure) is inversely proportional to the square of the current.

Inverse definite minimum time lag relay is also called ___________ (A) pilot relay. (B) differential relay. (C) over current relay. (D) directional overcurrent relay.

Description : Inverse definite minimum time lag relay is also called ___________ (A) pilot relay. (B) differential relay. (C) over current relay. (D) directional overcurrent relay.

Last Answer : Ans: B Inverse definite minimum time lag relay characteristic is inverse but minimum time is fixed. The operating time is inversely proportional to the magnitude of actuating quantity.

A three phase induction motor is driving full -load torque which is independent of speed. If the line voltage...

Description : A three phase induction motor is driving full -load torque which is independent of speed. If the line voltage drops to 90% of the rated value, % increase in motor copper losses  (a) 23% (b) -18% (c) 123% (d) None of these

Last Answer : A three phase induction motor is driving full -load torque which is independent of speed. If the line voltage drops to 90% of the rated value, % increase in motor copper losses (a) 23% (b) -18% (c) 123% (d) None of these

If the centrifugal switch or relay used for cutting out the starting winding of a split-phase induction motor fails to open once the motor is in operation, the _____________. A. motor will overspeed B. starting winding will burn out C. motor will immediately stall under load D. motor torque will be above normal at rated speed

Description : If the centrifugal switch or relay used for cutting out the starting winding of a split-phase induction motor fails to open once the motor is in operation, the _____________. A. motor will overspeed B ... C. motor will immediately stall under load D. motor torque will be above normal at rated speed

Last Answer : Answer: B

The effect of stray magnetic fields on the actuating torque of a portable instrument is maximum when the

Description : The effect of stray magnetic fields on the actuating torque of a portable instrument is maximum when the operating field of the instrument and the stray fields are  A) Perpendicular B) Parallel C) Inclined at 60" D) Inclined at 30°

Last Answer : The effect of stray magnetic fields on the actuating torque of a portable instrument is maximum when the operating field of the instrument and the stray fields are Parallel 

A 3-phase induction motor is driving a constant torque load at rated voltage and frequency. If both voltage

Description : A 3-phase induction motor is driving a constant torque load at rated voltage and frequency. If both voltage and frequency are halved, following statements relate to the new condition if stator resistance, leakage reactance and core loss are ... (A) All (B) 1, 2 and 3 (C) 2, 3 and 4 (D) 1 and 4

Last Answer : A 3-phase induction motor is driving a constant torque load at rated voltage and frequency. If both voltage and frequency are halved, following statements relate to the new condition if stator resistance, leakage reactance and core loss are ... A) All (B) 1, 2 and 3 (C) 2, 3 and 4 (D) 1 and 4

A three-phase, induction-type motor experiences an open in one phase. Which of the listed automatic protective devices will prevent the machine from being damaged? A. Overspeed trip B. Thermal overload relay C. Three-pole safety switch D. Magnetic blowout coil

Description : A three-phase, induction-type motor experiences an open in one phase. Which of the listed automatic protective devices will prevent the machine from being damaged? A. Overspeed trip B. Thermal overload relay C. Three-pole safety switch D. Magnetic blowout coil

Last Answer : Answer: B

Induction cup relay is operated due to changes in (a) current (b) voltage (c) impedance (d) all of the above

Description : Induction cup relay is operated due to changes in (a) current (b) voltage (c) impedance (d) all of the above

Last Answer : (d) all of the above

A hypothesis that States the nature (positive or negative) of the interaction between two or more variables is called a. Associated Hypothesis b. Casual Hypothesis c. Null Hypothesis d. Directional Hypothesis

Description : A hypothesis that States the nature (positive or negative) of the interaction between two or more variables is called a. Associated Hypothesis b. Casual Hypothesis c. Null Hypothesis d. Directional Hypothesis

Last Answer : d. Directional Hypothesis

If a three-phase induction motor is operated under a light load and it develops an open in one of its supply lines, the motor will _____________. A. continue to run, but will vibrate and have reduced torque B. speed up due to the reduced number of poles C. run cooler due to reduced current flow D. stop

Description : If a three-phase induction motor is operated under a light load and it develops an open in one of its supply lines, the motor will _____________. A. continue to run, but will vibrate and have reduced ... speed up due to the reduced number of poles C. run cooler due to reduced current flow D. stop

Last Answer : Answer: A

The relative speed between the magnetic fields of stator and rotor under steady state operation is zero for a (A) dc machine. (B) 3 phase induction machine. (C) synchronous machine. (D) single phase induction machine.

Description : The relative speed between the magnetic fields of stator and rotor under steady state operation is zero for a (A) dc machine. (B) 3 phase induction machine. (C) synchronous machine. (D) single phase induction machine.

Last Answer : Ans: all options are correct

In order to safely carry out repairs to a generator circuit breaker, it must be isolated from the bus. This is accomplished by opening the _____________. A. reverse power relay B. bus disconnect link C. generator bus fuse connections D. power directional relay

Description : In order to safely carry out repairs to a generator circuit breaker, it must be isolated from the bus. This is accomplished by opening the _____________. A. reverse power relay B. bus disconnect link C. generator bus fuse connections D. power directional relay

Last Answer : Answer: B

What are the features of directional relay?

Description : What are the features of directional relay?

Last Answer : High speed operation; high sensitivity; ability to operate at low voltages; adequate short-time thermal ratio; burden must not be excessive.

Admittance relay is _______ relay. (a) impedance (b) directional (c) non-directional (d) none of the above

Description : Admittance relay is _______ relay. (a) impedance (b) directional (c) non-directional (d) none of the above

Last Answer : (b) directional

The transmission line distance protection relay having the property of being inherently directional is

Description : The transmission line distance protection relay having the property of being inherently directional is (A) impedance relay (B) MHO relay (C) OHM relay (D) reactance relay

Last Answer : The transmission line distance protection relay having the property of being inherently directional is MHO relay

30°, 60° and 90° connections are made in a directional relay to render the relay

Description : 30°, 60° and 90° connections are made in a directional relay to render the relay (A) Sufficient torque under fault conditions (B) Zero torque under fault conditions (C) Current grading (D) Time grading

Last Answer : 30°, 60° and 90° connections are made in a directional relay to render the relay Sufficient torque under fault conditions

In a 15 HP induction-type motor with a cage rotor, the current required at standstill to produce starting torque is approximately ____________. A. half the full load current B. equal to the full load current C. five times the full load current D. ten to twenty times the full load current

Description : In a 15 HP induction-type motor with a cage rotor, the current required at standstill to produce starting torque is approximately ____________. A. half the full load current B. equal to the full load current C. five times the full load current D. ten to twenty times the full load current

Last Answer : Answer: C

Induction cup relay is operated due to changes in?

Last Answer : Induction cup relay is operated due to changes in current, voltage, impedance.

The torque and current curves for a three-phase induction motor with a cage rotor, are shown in the illustration. Which of the following statements is true concerning the depicted curves? EL-0056 A. As slip increases, rotor reactance decreases. B. The pullout point on the torque curve is about seven times the normal full load torque value. C. At stand still, stator current is 150% of normal. D. If the motor is loaded to the point where 40% slip has resulted, it will stall.

Description : The torque and current curves for a three-phase induction motor with a cage rotor, are shown in the illustration. Which of the following statements is true concerning the depicted curves? EL-0056 A. As slip ... D. If the motor is loaded to the point where 40% slip has resulted, it will stall.

Last Answer : Answer: D

If an induction motor were to be operated at 90% rated voltage, _____________. A. there would be an increase in starting torque B. starting current would increase slightly C. synchronous speed would decrease slightly D. the slip would increase

Description : If an induction motor were to be operated at 90% rated voltage, _____________. A. there would be an increase in starting torque B. starting current would increase slightly C. synchronous speed would decrease slightly D. the slip would increase

Last Answer : Answer: D

Regarding an induction motor, the power developed by the rotor automatically adjusts itself to the _____________. A. power required to drive the load B. speed required to drive the load C. current flow in the motor stator D. torque developed by the rotating field

Description : Regarding an induction motor, the power developed by the rotor automatically adjusts itself to the _____________. A. power required to drive the load B. speed required to drive the load C. current flow in the motor stator D. torque developed by the rotating field

Last Answer : Answer: A

Which motor has high Starting Torque and Staring current DC motor, Induction motor or Synchronous motor?

Description : Which motor has high Starting Torque and Staring current DC motor, Induction motor or Synchronous motor?

Last Answer : DC Series motor has high starting torque. We can not start the Induction motor and Synchronous motors on load, but can not start the DC series motor without load.

Which Motor Has High Starting Torque And Staring Current Dc Motor, Induction Motor Or Synchronous Motor?

Description : Which Motor Has High Starting Torque And Staring Current Dc Motor, Induction Motor Or Synchronous Motor?

Last Answer : DC Series motor has high starting torque. We can not start the Induction motor and Synchronous motors on load, but can not start the DC series motor without load.

In the heating process of the ________type a simple method of temperature control is possible by means of a special alloy which loses its magnetic properties at a particular high temperature and regains them when cooled to a temperature below this value. (A) Indirect induction over (B) core type induction furnace (C) coreless induction furnace (D) high frequency eddy current

Description : In the heating process of the ________type a simple method of temperature control is possible by means of a special alloy which loses its magnetic properties at a particular high temperature and regains ... ) core type induction furnace (C) coreless induction furnace (D) high frequency eddy current

Last Answer : Ans: D Magnetic property of alloy changes with change of the temperature and Heat is produced due to eddy current = i2R and i α f2

Due to the flow of current in a circular loop of radius `R`, the magnetic induction produced at the centre of the loop is `B`. The magnetic moment of

Description : Due to the flow of current in a circular loop of radius `R`, the magnetic induction produced at the centre of the loop is `B`. The magnetic moment of

Last Answer : Due to the flow of current in a circular loop of radius `R`, the magnetic induction produced at the centre of the ... )` D. `(2pi BR^(2))/(mu_(0))`

When a certain length of wire is turned into one circular loop, the magnetic induction at the centre of coil due to some current flowing is `B_(1)` If

Description : When a certain length of wire is turned into one circular loop, the magnetic induction at the centre of coil due to some current flowing is `B_(1)` If

Last Answer : When a certain length of wire is turned into one circular loop, the magnetic induction at the centre of coil due to ... 1)` C. `3B_(1)` D. `27B_(1)`

At slip equal to infinity, the torque of a three phase induction motor is :-

Description : At slip equal to infinity, the torque of a three phase induction motor is :-  a) zero b) very small c) high d) very high

Last Answer : At slip equal to infinity, the torque of a three phase induction motor is :- zero

Reduction in supply voltage by 10% will change the torque of an induction motor by

Description : Reduction in supply voltage by 10% will change the torque of an induction motor by   (a) 38% (b) 19% (c) 9.5% (d) No change 

Last Answer : Answer is (b)

Starting torque can be obtained in the case of a single phase induction motor with identical main and ...

Description : Starting torque can be obtained in the case of a single phase induction motor with identical main and auxiliary windings by connecting:  (1) A capacitor across the mains (2) A capacitor in ... with the auxiliary winding (4) Equal value capacitors in series with the main and the auxiliary windings

Last Answer : Starting torque can be obtained in the case of a single phase induction motor with identical main and auxiliary windings by connecting:  A capacitor is series with the auxiliary winding.

In an induction motor, if the rotor resistance is equal to stand-still reactance then the maximum torque is_________.

Last Answer : In an induction motor, if the rotor resistance is equal to stand-still reactance then the maximum torque is equal to starting torque.

The forces of cathode ray particles due to electric and magnetic fields which are at right angles to each other balance each other. If the magnetic fi

Description : The forces of cathode ray particles due to electric and magnetic fields which are at right angles to each other balance each other. If the magnetic fi

Last Answer : The forces of cathode ray particles due to electric and magnetic fields which are at right angles to ... p.d. is required to produce this velocity?

The timer element found in a reverse power relay obtains its operating torque via _____________. A. line voltage B. the main bus C. electromagnets D. a separate battery source

Description : The timer element found in a reverse power relay obtains its operating torque via _____________. A. line voltage B. the main bus C. electromagnets D. a separate battery source

Last Answer : Answer: C

relay is preferred for phase fault on short transmission line. (a) Induction type (b) Reactance (c) Impedance (d) None of the above

Description : relay is preferred for phase fault on short transmission line. (a) Induction type (b) Reactance (c) Impedance (d) None of the above

Last Answer : (b) Reactance

The purpose of an impressed current cathodic protection system aboard ship is to _______________. A. prevent corrosion of the hull, propeller, rudder and line shafting B. neutralize the vessel's stray magnetic fields which would interfere with radar C. protect engine room and deck machinery from oxidation in the presence of salt air D. maintain a minimum constant alternator load to prevent overheating

Description : The purpose of an impressed current cathodic protection system aboard ship is to _______________. A. prevent corrosion of the hull, propeller, rudder and line shafting B. neutralize the vessel's ... the presence of salt air D. maintain a minimum constant alternator load to prevent overheating

Last Answer : Answer: A

One method of testing for a reversed shunt field coil in a DC generator or motor is by connecting the field to a direct current source, at reduced field rated voltage, and test for polarity using a/an ____________. A. iron bar across each field B. magnetic compass placed near each field C. test lamp across adjacent fields D. copper jumper across the interpole connections

Description : One method of testing for a reversed shunt field coil in a DC generator or motor is by connecting the field to a direct current source, at reduced field rated voltage, and test for ... placed near each field C. test lamp across adjacent fields D. copper jumper across the interpole connections

Last Answer : Answer: B

When current is parallel to magnetic fields, force on conductor is A. zeroB. infinite C. 2 times D. same

Description : When current is parallel to magnetic fields, force on conductor is A. zeroB. infinite C. 2 times D. same

Last Answer : zero

Magnetic fields are produced by: w) resistance x) an electric potential difference y) electric current z) stationary charge

Description : Magnetic fields are produced by: w) resistance x) an electric potential difference y) electric current z) stationary charge

Last Answer : ANSWER: Y -- CURRENT 

The action of electromagnetic machines can be related to which ofthe following basic principles ? (a) Induction (b) Interaction (c) Alignment (d) All of the above

Description : The action of electromagnetic machines can be related to which ofthe following basic principles ? (a) Induction (b) Interaction (c) Alignment (d) All of the above

Last Answer : (d) All of the above

If a magnetic controller relay fails to drop out when the coil voltage is removed from the relay, the probable cause may be _____________. A. excessive spring tension B. overvoltage C. excessive current D. welded contacts

Description : If a magnetic controller relay fails to drop out when the coil voltage is removed from the relay, the probable cause may be _____________. A. excessive spring tension B. overvoltage C. excessive current D. welded contacts

Last Answer : Answer: D

Mention some of the applications of Directional Over-Current relays?

Description : Mention some of the applications of Directional Over-Current relays?

Last Answer : 1. Double end fed power system 2. Single end fed system of parallel feeders 3. Ring main feeder system