Band loss is ∙ a. A reduction in transmitter power caused by earth’s surface curvature ∙ b. A reduction in strength of the signal caused by folded dipole bends ∙ c. An attenuation increase caused by bends radiating from the side of the fiber ∙ d. All of these

Band loss is
∙ a. A reduction in transmitter power caused by earth’s surface curvature  
∙ b. A reduction in strength of the signal caused by folded dipole bends  
∙ c. An attenuation increase caused by bends radiating from the side of the fiber  
∙ d. All of these
by

1 Answer

Answer :

c. An attenuation increase caused by bends radiating from the side of the fiber
by

Related questions

The loss in signal power as light travels down a fiber is called ∙ a. Dispersion ∙ b. Scattering ∙ c. Absorption ∙ d. Attenuation

Description : The loss in signal power as light travels down a fiber is called ∙ a. Dispersion ∙ b. Scattering ∙ c. Absorption ∙ d. Attenuation

Last Answer : ∙ d. Attenuation

These bends are caused by excessive pressure and tension and generally occur while fiber are bent during handling or installation. ∙ A. microbending ∙ B. macrobending ∙ C. constant-radius bending ∙ D. kinks

Description : These bends are caused by excessive pressure and tension and generally occur while fiber are bent during handling or installation. ∙ A. microbending ∙ B. macrobending ∙ C. constant-radius bending ∙ D. kinks

Last Answer : C. constant-radius bending

The term power budgeting refers to ∙ A. the cost of cable, connectors, equipment and installation ∙ B. the loss of power due to defective components ∙ C. the total power available minus the attenuation losses ∙ D. the comparative costs of fiber and copper installations

Description : The term power budgeting refers to ∙ A. the cost of cable, connectors, equipment and installation ∙ B. the loss of power due to defective components ∙ C. the total power available minus the attenuation losses ∙ D. the comparative costs of fiber and copper installations

Last Answer : C. the total power available minus the attenuation losses

When connector losses, splice losses and coupler losses are added, what is the limiting factor? ∙ A. source power ∙ B. fiber attenuation ∙ C. connector and splice loss ∙ D. detector sensitivity

Description : When connector losses, splice losses and coupler losses are added, what is the limiting factor? ∙ A. source power ∙ B. fiber attenuation ∙ C. connector and splice loss ∙ D. detector sensitivity

Last Answer : D. detector sensitivity

Why are visible-light LEDs not used for fiber optics? ∙ a. It has high losses ∙ b. It has short wave ∙ c. It has low attenuation ∙ d. It has weak signal

Description : Why are visible-light LEDs not used for fiber optics? ∙ a. It has high losses ∙ b. It has short wave ∙ c. It has low attenuation ∙ d. It has weak signal

Last Answer : ∙ a. It has high losses

A fiber-optic cable has a loss of 15 dB/km. The attenuation in a cable 1000 ft. long is ∙ A. 4.57 dB ∙ B. 9.3 dB ∙ C. 24 dB ∙ D. 49.2 dB

Description : A fiber-optic cable has a loss of 15 dB/km. The attenuation in a cable 1000 ft. long is ∙ A. 4.57 dB ∙ B. 9.3 dB ∙ C. 24 dB ∙ D. 49.2 dB

Last Answer : A. 4.57 dB

Fiber-optic cables with attenuation of 1.8, 3.4, 5.9 and 18 dB are linked together. The total loss is ∙ A. 7.5 dB ∙ B. 19.8 dB ∙ C. 29.1 dB ∙ D. 650 dB

Description : Fiber-optic cables with attenuation of 1.8, 3.4, 5.9 and 18 dB are linked together. The total loss is ∙ A. 7.5 dB ∙ B. 19.8 dB ∙ C. 29.1 dB ∙ D. 650 dB

Last Answer : C. 29.1 dB

Which is not a possible cause of optical fiber loss? ∙ a. Impurities ∙ b. Glass attenuation ∙ c. Stepped index operation ∙ d. Microbending

Description : Which is not a possible cause of optical fiber loss? ∙ a. Impurities ∙ b. Glass attenuation ∙ c. Stepped index operation ∙ d. Microbending

Last Answer : ∙ c. Stepped index operation

Under normal condition, a single fiber should not be used for a two-way communication mainly because of ∙ a. Loss ∙ b. Fading ∙ c. Noise ∙ d. Attenuation

Description : Under normal condition, a single fiber should not be used for a two-way communication mainly because of ∙ a. Loss ∙ b. Fading ∙ c. Noise ∙ d. Attenuation

Last Answer : ∙ c. Noise

. A fiber-optic cable has a loss of 15 dB/km. The attenuation in a cable, 100 ft long is ∙ a. 4.57 dB ∙ b. 9.3 dB ∙ c. 24 dB ∙ d. 49.2 dB

Description : . A fiber-optic cable has a loss of 15 dB/km. The attenuation in a cable, 100 ft long is ∙ a. 4.57 dB ∙ b. 9.3 dB ∙ c. 24 dB ∙ d. 49.2 dB

Last Answer : ∙ a. 4.57 dB

The following are the cause of light attenuation in fiber optics except ∙ a. Backscattering ∙ b. Absorption ∙ c. Refraction ∙ d. Microbends

Description : The following are the cause of light attenuation in fiber optics except ∙ a. Backscattering ∙ b. Absorption ∙ c. Refraction ∙ d. Microbends

Last Answer : c. Refraction

Cable attenuation is usually expressed in terms of ∙ A. loss per foot ∙ B. dB/km ∙ C. intensity per mile ∙ D. voltage drop per inch

Description : Cable attenuation is usually expressed in terms of ∙ A. loss per foot ∙ B. dB/km ∙ C. intensity per mile ∙ D. voltage drop per inch

Last Answer : . dB/km

The mechanical splice attenuation loss is _____ dB or less ∙ a. 0.1 ∙ b. 0.01 ∙ c. 0.001 ∙ d. 1

Description : The mechanical splice attenuation loss is _____ dB or less ∙ a. 0.1 ∙ b. 0.01 ∙ c. 0.001 ∙ d. 1

Last Answer : a. 0.1

Cable attenuation is usually expressed in terms of ∙ a. Loss per foot ∙ b. dB/km ∙ c. intensity per mile ∙ d. voltage drop per inch

Description : Cable attenuation is usually expressed in terms of ∙ a. Loss per foot ∙ b. dB/km ∙ c. intensity per mile ∙ d. voltage drop per inch

Last Answer : ∙ b. dB/km

Used to test a fiber optics splice ∙ a. Spectrum analyzer ∙ b. Oscilloscope ∙ c. Optical power meter ∙ d. Field strength meter

Description : Used to test a fiber optics splice ∙ a. Spectrum analyzer ∙ b. Oscilloscope ∙ c. Optical power meter ∙ d. Field strength meter

Last Answer : c. Optical power meter

Results in reduction in the power of light wave as it travels down the cable. ∙ A. power loss ∙ B. absorption loss ∙ C. resistive loss ∙ D. heat loss

Description : Results in reduction in the power of light wave as it travels down the cable. ∙ A. power loss ∙ B. absorption loss ∙ C. resistive loss ∙ D. heat loss

Last Answer : A. power loss

It is analogous to power dissipation to copper cables, impurities in the fiber absorb the light and covert it to heat. ∙ A. power loss ∙ B. absorption loss ∙ C. resistive loss ∙ D. heat loss

Description : It is analogous to power dissipation to copper cables, impurities in the fiber absorb the light and covert it to heat. ∙ A. power loss ∙ B. absorption loss ∙ C. resistive loss ∙ D. heat loss

Last Answer : B. absorption loss

It indicates what signal frequencies can be propagated through a given distance of fiber cable. ∙ A. Bandwidth Distance Product ∙ B. Pulse width dispersion ∙ C. Rise time ∙ D. Cutoff frequency

Description : It indicates what signal frequencies can be propagated through a given distance of fiber cable. ∙ A. Bandwidth Distance Product ∙ B. Pulse width dispersion ∙ C. Rise time ∙ D. Cutoff frequency

Last Answer : A. Bandwidth Distance Product

The upper pulse rate and information-carrying capacity of a cable is limited by ∙ A. pulse shortening ∙ B. attenuation ∙ C. light leakage ∙ D. modal dispersion

Description : The upper pulse rate and information-carrying capacity of a cable is limited by ∙ A. pulse shortening ∙ B. attenuation ∙ C. light leakage ∙ D. modal dispersion

Last Answer : D. modal dispersion

The mechanical splice is best suited for ∙ A. quicker installation under ideal condition ∙ B. minimum attenuation losses ∙ C. field service conditions ∙ D. situations in which cost of equipment is not a factor

Description : The mechanical splice is best suited for ∙ A. quicker installation under ideal condition ∙ B. minimum attenuation losses ∙ C. field service conditions ∙ D. situations in which cost of equipment is not a factor

Last Answer : D. situations in which cost of equipment is not a factor

Which cable length has the highest attenuation? ∙ A. 1 km ∙ B. 2 km ∙ C. 95 ft. ∙ D. 500 ft.

Description : Which cable length has the highest attenuation? ∙ A. 1 km ∙ B. 2 km ∙ C. 95 ft. ∙ D. 500 ft.

Last Answer : B. 2 km

The upper pulse rate and information carrying capacity of a cable is limited by ∙ a. Pulse shortening ∙ b. Attenuation ∙ c. Light leakage ∙ d. Modal dispersion

Description : The upper pulse rate and information carrying capacity of a cable is limited by ∙ a. Pulse shortening ∙ b. Attenuation ∙ c. Light leakage ∙ d. Modal dispersion

Last Answer : ∙ d. Modal dispersion

Which of the cable length has the highest attenuation? ∙ a. 1 km ∙ b. 2 km ∙ c. 95 ft ∙ d. 5500 ft

Description : Which of the cable length has the highest attenuation? ∙ a. 1 km ∙ b. 2 km ∙ c. 95 ft ∙ d. 5500 ft

Last Answer : ∙ b. 2 km

It is caused by the difference in the propagation time of light rays that take different paths down the fiber. ∙ A. modal dispersion ∙ B. microbending ∙ C. Rayleigh scattering ∙ D. chromatic dispersion

Description : It is caused by the difference in the propagation time of light rays that take different paths down the fiber. ∙ A. modal dispersion ∙ B. microbending ∙ C. Rayleigh scattering ∙ D. chromatic dispersion

Last Answer : A. modal dispersion

It is caused by valence electrons in the silica material from which the fiber are manufactured. ∙ A. ion resonance absorption ∙ B. infrared absorption ∙ C. ultraviolet absorption ∙ D. visible light absorption

Description : It is caused by valence electrons in the silica material from which the fiber are manufactured. ∙ A. ion resonance absorption ∙ B. infrared absorption ∙ C. ultraviolet absorption ∙ D. visible light absorption

Last Answer : ultraviolet absorption

______ dispersion is caused by the difference in the propagation times of light rays that take different paths down a fiber. ∙ a. Material dispersion ∙ b. Wavelength dispersion ∙ c. Modal dispersion

Description : ______ dispersion is caused by the difference in the propagation times of light rays that take different paths down a fiber. ∙ a. Material dispersion ∙ b. Wavelength dispersion ∙ c. Modal dispersion

Last Answer : ∙ c. Modal dispersion

What is the average loss in fiber splice? ∙ a. 0.10 dB ∙ b. 0.15 dB ∙ c. 0.20 dB ∙ d. 0.25 dB

Description : What is the average loss in fiber splice? ∙ a. 0.10 dB ∙ b. 0.15 dB ∙ c. 0.20 dB ∙ d. 0.25 dB

Last Answer : 0.15 dB

The dominant loss mechanisms in silica fiber are ∙ a. Absorption and radiation losses ∙ b. Absorption and Rayleigh scattering ∙ c. Coupling and radiation losses ∙ d. Radiation and modal dispersion

Description : The dominant loss mechanisms in silica fiber are ∙ a. Absorption and radiation losses ∙ b. Absorption and Rayleigh scattering ∙ c. Coupling and radiation losses ∙ d. Radiation and modal dispersion

Last Answer : b. Absorption and Rayleigh scattering

When light strikes a flat polished end of a fiber, the fiber loss produced can be reduced by ∙ a. Splicing ∙ b. Antireflection coating ∙ c. Insulation jacket ∙ d. All of these

Description : When light strikes a flat polished end of a fiber, the fiber loss produced can be reduced by ∙ a. Splicing ∙ b. Antireflection coating ∙ c. Insulation jacket ∙ d. All of these

Last Answer : ∙ b. Antireflection coating

When light strikes a flat polished end of a fiber, it produces a loss of ∙ a. 14 % ∙ b. 4 % ∙ c. 10 % ∙ d. 1 %

Description : When light strikes a flat polished end of a fiber, it produces a loss of ∙ a. 14 % ∙ b. 4 % ∙ c. 10 % ∙ d. 1 %

Last Answer : ∙ b. 4 %

Fiber-optic cables with attenuations of 1.8, 3.4, 5.9, and 18 dB are linked together. The total loss is ∙ a. 7.5 dB ∙ b. 19.8 dB ∙ c. 29.1 dB ∙ d. 650 dB

Description : Fiber-optic cables with attenuations of 1.8, 3.4, 5.9, and 18 dB are linked together. The total loss is ∙ a. 7.5 dB ∙ b. 19.8 dB ∙ c. 29.1 dB ∙ d. 650 dB

Last Answer : ∙ c. 29.1 dB

What is the insertion loss of connector-type splices for a single mode fiber optics? ∙ a. 0.51 dB ∙ b. 0.31 dB ∙ c. 0.49 dB ∙ d. 0.38 dB

Description : What is the insertion loss of connector-type splices for a single mode fiber optics? ∙ a. 0.51 dB ∙ b. 0.31 dB ∙ c. 0.49 dB ∙ d. 0.38 dB

Last Answer : d. 0.38 dB

What is the average insertion loss of fusion splice in fiber optics? ∙ a. 0.09 dB ∙ b. 0.9 dB ∙ c. 0.19 dB ∙ d. 0.009 dB

Description : What is the average insertion loss of fusion splice in fiber optics? ∙ a. 0.09 dB ∙ b. 0.9 dB ∙ c. 0.19 dB ∙ d. 0.009 dB

Last Answer : ∙ b. 0.9 dB

An increase in light intensity produces fast optic switching due to ∙ a. Increase in index of glass ∙ b. Amplification of optical signal ∙ c. High gain ∙ d. Photoconductivity

Description : An increase in light intensity produces fast optic switching due to ∙ a. Increase in index of glass ∙ b. Amplification of optical signal ∙ c. High gain ∙ d. Photoconductivity

Last Answer : b. Amplification of optical signal

The three major groups of the optical system are ∙ A. the components, the data rate and the response time ∙ B. the source, the link and the receiver ∙ C. the transmitter, the cable and the receiver ∙ D. the source, the link and the detector

Description : The three major groups of the optical system are ∙ A. the components, the data rate and the response time ∙ B. the source, the link and the receiver ∙ C. the transmitter, the cable and the receiver ∙ D. the source, the link and the detector

Last Answer : B. the source, the link and the receiver

Optical cable testers are used for ∙ a. Checking refractive index ∙ b. Light power out of a fiber ∙ c. Non-calibrated light into a fiber

Description : Optical cable testers are used for ∙ a. Checking refractive index ∙ b. Light power out of a fiber ∙ c. Non-calibrated light into a fiber

Last Answer : b. Light power out of a fiber

Optical cable testers are used for ∙ a. Checking refractive index ∙ b. Light power out of a fiber ∙ c. Non-calibrated light into a fiber

Description : Optical cable testers are used for ∙ a. Checking refractive index ∙ b. Light power out of a fiber ∙ c. Non-calibrated light into a fiber

Last Answer : ∙ b. Light power out of a fiber

The minimum optical power a light detector can receive and still produce a usable electrical output signal. ∙ A. light responsivity ∙ B. light sensitivity ∙ C. light collectivity ∙ D. illumination

Description : The minimum optical power a light detector can receive and still produce a usable electrical output signal. ∙ A. light responsivity ∙ B. light sensitivity ∙ C. light collectivity ∙ D. illumination

Last Answer : B. light sensitivity

The term responsivity as it applies to a light detector is best described as ∙ A. the time required for the signal to go from 10 to 90 percent of maximum amplitude ∙ B. the ratio of the diode output current to the input optical power ∙ C. the ratio of the input power to output power ∙ D. the ratio of output current to input current

Description : The term responsivity as it applies to a light detector is best described as ∙ A. the time required for the signal to go from 10 to 90 percent of maximum amplitude ∙ B. the ratio of the diode ... . the ratio of the input power to output power ∙ D. the ratio of output current to input current

Last Answer : the ratio of the diode output current to the input optical power

Calculate the total rise time for a fiber-optic system if the transmitter, receiver, and cable each have a rise time of 50 nanoseconds.

Description : Calculate the total rise time for a fiber-optic system if the transmitter, receiver, and cable each have a rise time of 50 nanoseconds.

Last Answer : 86.6 nanoseconds

Fiber-optic cable cannot be used: a. in an explosive environment b. to connect a transmitter to an antenna c. to isolate a medical patient from a shock hazard d. none of the above

Description : Fiber-optic cable cannot be used: a. in an explosive environment b. to connect a transmitter to an antenna c. to isolate a medical patient from a shock hazard d. none of the above

Last Answer : b. to connect a transmitter to an antenna

Which type of fiber-optic cable is the most widely used? ∙ A. single-mode step-index ∙ B. multimode step-index ∙ C. single-mode graded index ∙ D. multimode graded index

Description : Which type of fiber-optic cable is the most widely used? ∙ A. single-mode step-index ∙ B. multimode step-index ∙ C. single-mode graded index ∙ D. multimode graded index

Last Answer : B. multimode step-index

EMD is best described by which statement? ∙ A. 70 percent of the core diameter and 70% of the fiber NA should be filled with light. ∙ B. 70 percent of the fiber diameter and 70% of the cone of acceptance should be filled with light. ∙ C. 70 percent of input light should be measured at the output. ∙ D. 70 percent of the unwanted wavelengths should be attenuated by the fiber.

Description : EMD is best described by which statement? ∙ A. 70 percent of the core diameter and 70% of the fiber NA should be filled with light. ∙ B. 70 percent of the fiber diameter and 70% of the ... be measured at the output. ∙ D. 70 percent of the unwanted wavelengths should be attenuated by the fiber.

Last Answer : 70 percent of the core diameter and 70% of the fiber NA should be filled with light.

Which of the following is not a major benefit of a fiber-optic cable? ∙ A. immunity from interference ∙ B. no electrical safety problems ∙ C. excellent data security ∙ D. lower cost

Description : Which of the following is not a major benefit of a fiber-optic cable? ∙ A. immunity from interference ∙ B. no electrical safety problems ∙ C. excellent data security ∙ D. lower cost

Last Answer : ∙ D. lower cost

The core of fiber-optic cable is surrounded by ∙ A. wire braid shield ∙ B. Keviar ∙ C. cladding ∙ D. plastic insulation

Description : The core of fiber-optic cable is surrounded by ∙ A. wire braid shield ∙ B. Keviar ∙ C. cladding ∙ D. plastic insulation

Last Answer : ∙ C. cladding

The core of a fiber-optic cable is made of ∙ A. air ∙ B. glass ∙ C. diamond ∙ D. quartz

Description : The core of a fiber-optic cable is made of ∙ A. air ∙ B. glass ∙ C. diamond ∙ D. quartz

Last Answer : B. glass

Which of the following is not a common type of fiber-optic cable? ∙ A. single-mode step-index ∙ B. multimode graded-index ∙ C. single-mode graded-index ∙ D. multimode step-index

Description : Which of the following is not a common type of fiber-optic cable? ∙ A. single-mode step-index ∙ B. multimode graded-index ∙ C. single-mode graded-index ∙ D. multimode step-index

Last Answer : . single-mode graded-index

The operation of a fiber-optic cable is based on the principle of ∙ A. refraction ∙ B. reflection ∙ C. dispersion ∙ D. absorption

Description : The operation of a fiber-optic cable is based on the principle of ∙ A. refraction ∙ B. reflection ∙ C. dispersion ∙ D. absorption

Last Answer : A. refraction