Description : Fiber-optic cables with attenuations of 1.8, 3.4, 5.9, and 18 dB are linked together. The total loss is ∙ a. 7.5 dB ∙ b. 19.8 dB ∙ c. 29.1 dB ∙ d. 650 dB
Last Answer : ∙ c. 29.1 dB
Description : A fiber-optic cable has a loss of 15 dB/km. The attenuation in a cable 1000 ft. long is ∙ A. 4.57 dB ∙ B. 9.3 dB ∙ C. 24 dB ∙ D. 49.2 dB
Last Answer : A. 4.57 dB
Description : . A fiber-optic cable has a loss of 15 dB/km. The attenuation in a cable, 100 ft long is ∙ a. 4.57 dB ∙ b. 9.3 dB ∙ c. 24 dB ∙ d. 49.2 dB
Last Answer : ∙ a. 4.57 dB
Description : What is the average insertion loss of fusion splice in fiber optics? ∙ a. 0.09 dB ∙ b. 0.9 dB ∙ c. 0.19 dB ∙ d. 0.009 dB
Last Answer : ∙ b. 0.9 dB
Description : The term power budgeting refers to ∙ A. the cost of cable, connectors, equipment and installation ∙ B. the loss of power due to defective components ∙ C. the total power available minus the attenuation losses ∙ D. the comparative costs of fiber and copper installations
Last Answer : C. the total power available minus the attenuation losses
Description : Cable attenuation is usually expressed in terms of ∙ A. loss per foot ∙ B. dB/km ∙ C. intensity per mile ∙ D. voltage drop per inch
Last Answer : . dB/km
Description : The mechanical splice attenuation loss is _____ dB or less ∙ a. 0.1 ∙ b. 0.01 ∙ c. 0.001 ∙ d. 1
Last Answer : a. 0.1
Description : Cable attenuation is usually expressed in terms of ∙ a. Loss per foot ∙ b. dB/km ∙ c. intensity per mile ∙ d. voltage drop per inch
Last Answer : ∙ b. dB/km
Description : Fiber optic cables operate at frequencies near ∙ a. 20 MHz ∙ b. 200 MHz ∙ c. 2G Hz ∙ d. 800 THz
Last Answer : ∙ d. 800 THz
Description : When connector losses, splice losses and coupler losses are added, what is the limiting factor? ∙ A. source power ∙ B. fiber attenuation ∙ C. connector and splice loss ∙ D. detector sensitivity
Last Answer : D. detector sensitivity
Description : Which is not a possible cause of optical fiber loss? ∙ a. Impurities ∙ b. Glass attenuation ∙ c. Stepped index operation ∙ d. Microbending
Last Answer : ∙ c. Stepped index operation
Description : Under normal condition, a single fiber should not be used for a two-way communication mainly because of ∙ a. Loss ∙ b. Fading ∙ c. Noise ∙ d. Attenuation
Last Answer : ∙ c. Noise
Description : Band loss is ∙ a. A reduction in transmitter power caused by earth’s surface curvature ∙ b. A reduction in strength of the signal caused by folded dipole bends ∙ c. An attenuation increase caused by bends radiating from the side of the fiber ∙ d. All of these
Last Answer : c. An attenuation increase caused by bends radiating from the side of the fiber
Description : The loss in signal power as light travels down a fiber is called ∙ a. Dispersion ∙ b. Scattering ∙ c. Absorption ∙ d. Attenuation
Last Answer : ∙ d. Attenuation
Description : The loss in single-mode fiber-optic cable due to a connector is about: a. 0.02 dB b. 0.2 dB c. 1 dB d. 3 dB
Last Answer : b. 0.2 dB
Description : The loss in single-mode fiber-optic cable due to a splice is about: a. 0.02 dB b. 0.2 dB c. 1 dB d. 3 dB
Last Answer : a. 0.02 dB
Description : The loss in single-mode fiber-optic cable due to the glass is about: a. 40 dB per km b. 4 db per km c. 0.4 dB per km d. zero loss
Last Answer : c. 0.4 dB per km
Description : A popular light wavelength fiber-optic cable is ∙ A. 0.7 micrometer ∙ B. 1.3 micrometer ∙ C. 1.5 micrometer ∙ D. 1.8 micrometer
Last Answer : B. 1.3 micrometer
Description : A popular light wavelength in fiber-optic cable is ∙ a. 0.7 um ∙ b. 1.3 um ∙ c. 1.5 um ∙ d. 1.8 um
Last Answer : b. 1.3 um
Description : What is the average loss in fiber splice? ∙ a. 0.10 dB ∙ b. 0.15 dB ∙ c. 0.20 dB ∙ d. 0.25 dB
Last Answer : 0.15 dB
Description : What is the insertion loss of connector-type splices for a single mode fiber optics? ∙ a. 0.51 dB ∙ b. 0.31 dB ∙ c. 0.49 dB ∙ d. 0.38 dB
Last Answer : d. 0.38 dB
Description : It is analogous to power dissipation to copper cables, impurities in the fiber absorb the light and covert it to heat. ∙ A. power loss ∙ B. absorption loss ∙ C. resistive loss ∙ D. heat loss
Last Answer : B. absorption loss
Description : . Which fiber-optic system is better? ∙ A. 3 repeaters ∙ B. 8 repeaters ∙ C. 11 repeaters ∙ D. 20 repeaters
Last Answer : A. 3 repeaters
Description : Which fiber-optic system is better? ∙ a. 3 repeaters ∙ b. 8 repeaters ∙ c. 11 repeaters ∙ d. 20 repeaters
Last Answer : a. 3 repeaters
Description : Why are visible-light LEDs not used for fiber optics? ∙ a. It has high losses ∙ b. It has short wave ∙ c. It has low attenuation ∙ d. It has weak signal
Last Answer : ∙ a. It has high losses
Description : The following are the cause of light attenuation in fiber optics except ∙ a. Backscattering ∙ b. Absorption ∙ c. Refraction ∙ d. Microbends
Last Answer : c. Refraction
Description : Developed an optical fiber with losses less that 2 dB/km ∙ A. Kao and Bockham ∙ B. Maiman, Kao and Bockham ∙ C. Maiman and Schawlow ∙ D. Kapron, Keck and Maurer
Last Answer : ∙ A. Kao and Bockham
Description : The use of solitons on fiber-optic cables is: a. common b. experimental c. obsolete d. not possible
Last Answer : b. experimental
Description : Fiber-optic cables do not: a. carry current b. cause crosstalk c. generate EMI d. all of the above
Last Answer : d. all of the above
Description : . The product of the bit rate and distance of a fiber-optic system is 2 Gbits-km/s. What is the maximum rate at 5 km? ∙ A. 100 Mbits/s ∙ B. 200 Mbits/s ∙ C. 400 Mbits/s ∙ D. 1000 Gbits/s
Last Answer : C. 400 Mbits/s
Description : The product of the bit rate and distance of a fiber-optic system is 2 Gbits km/s. What is the maximum rate at 5 km? ∙ a. 100 Mbits/s ∙ b. 200 Mbits/s ∙ c. 400 Mbits/s ∙ d. 1000 Gbits/s
Last Answer : c. 400 Mbits/s
Description : They proposed a new communication medium using cladded fiber cables. ∙ A. Kao and Bockham ∙ B. Maiman, Kao and Bockham ∙ C. Kapron, Keck and Maurer ∙ D. Maiman and Schawlow
Description : They were granted patents for scanning and transmitting television images through uncoated fiber cables. ∙ A. Baird and Hansel ∙ B. Bockham and Kao ∙ C. Kapron and Keck
Last Answer : A. Baird and Hansel
Description : Which type of fiber-optic cable is the most widely used? ∙ A. single-mode step-index ∙ B. multimode step-index ∙ C. single-mode graded index ∙ D. multimode graded index
Last Answer : B. multimode step-index
Description : Which of the following is not a major benefit of a fiber-optic cable? ∙ A. immunity from interference ∙ B. no electrical safety problems ∙ C. excellent data security ∙ D. lower cost
Last Answer : ∙ D. lower cost
Description : The core of fiber-optic cable is surrounded by ∙ A. wire braid shield ∙ B. Keviar ∙ C. cladding ∙ D. plastic insulation
Last Answer : ∙ C. cladding
Description : The core of a fiber-optic cable is made of ∙ A. air ∙ B. glass ∙ C. diamond ∙ D. quartz
Last Answer : B. glass
Description : Which of the following is not a common type of fiber-optic cable? ∙ A. single-mode step-index ∙ B. multimode graded-index ∙ C. single-mode graded-index ∙ D. multimode step-index
Last Answer : . single-mode graded-index
Description : The operation of a fiber-optic cable is based on the principle of ∙ A. refraction ∙ B. reflection ∙ C. dispersion ∙ D. absorption
Last Answer : A. refraction
Description : Which of the following is not a common application of fiber-optic cable? ∙ A. computer networks ∙ B. long-distance telephone system ∙ C. closed-circuit TV ∙ D. consumer TV
Last Answer : ∙ D. consumer TV
Description : Which type of fiber optic cable is best for very high speed data? ∙ A. single-mode step-index ∙ B. multimode step-index ∙ C. single-mode graded-index ∙ D. multimode graded-index
Last Answer : A. single-mode step-index
Description : Which type of fiber-optic cable has the least modal dispersion? ∙ A. single-mode step-index ∙ B. multimode step-index ∙ C. single-mode graded-index ∙ D. multimode graded-index
Description : The term single mode and multimode are best described as ∙ A. a number of fibers placed into fiber-optic cable ∙ B. the number of voice channels each fiber can support ∙ C. the number of wavelengths each fiber can support ∙ D. the index number
Last Answer : C. the number of wavelengths each fiber can support
Description : Which light emitter is preferred for high-speed data in a fiber-optic system? ∙ A. incandescent ∙ B. LED ∙ C. neon ∙ D. laser
Last Answer : D. laser
Description : Most fiber optic light sources emit light in which spectrum? ∙ A. visible ∙ B. infrared ∙ C. ultraviolet ∙ D. X-ray
Last Answer : B. infrared
Description : SONET stands for ∙ a. System Optical Network ∙ b. Synchronous Optical Network ∙ c. Silica Optic Network ∙ d. System Optical Fiber Net
Last Answer : ∙ b. Synchronous Optical Network
Description : Most fiber-optic light sources emit light in which spectrum? ∙ a. Visible ∙ b. Infrared ∙ c. Ultraviolet ∙ d. X-ray
Last Answer : ∙ b. Infrared
Description : Which light emitter is preferred for high speed data in a fiber-optic system ∙ a. Incandescent ∙ b. LED ∙ c. Neon ∙ d. Laser
Last Answer : ∙ d. Laser
Description : Which type of fiber-optic cable has the least modal dispersion? ∙ a. Single mode step-index ∙ b. Multimode step-index ∙ c. Single-mode graded-index ∙ d. Multimode graded-index
Last Answer : ∙ a. Single mode step-index
Description : Which type of fiber-optic cable is the best for very high speed data? ∙ a. Single-mode step-index ∙ b. Multimode step-index ∙ c. Single-mode graded-index ∙ d. Multimode graded-index
Last Answer : a. Single-mode step-index