Description : The collector-injection modulator is similar to what type of tube modulator?
Last Answer : Plate modulator.
Description : The common-emitter transistor circuit can amplify a small current signal because a small change in the signal current produces one of the following. Does the change in signal produce a large change in the: w) emitter-base voltage x) base current y) collector current z) collector voltage
Last Answer : ANSWER: Y -- COLLECTOR CURRENT
Description : Which of the following actions can be carried out in order to prevent thermal runaway in a transistor? A. Increase the current through the collector-base junction. B. Install a heat sink. ... point to increase collector current. D. Increase the potential difference between the emitter and the base.
Last Answer : Answer: B
Description : Under ideal conditions, the collector current is (a) Equal to base current (b) Nearly equal to emitter current (c) Less than base current (d) always zero
Last Answer : (b) Nearly equal to emitter current
Description : In p-n-p transistor, collector current is (a) Equal to emitter current (b) slightly less than emitter current (c) greater than emitter current (d) any of above
Last Answer : (c) greater than emitter current
Description : In the common–emitter transistor circuit, if the current gain is 100 and the collector current is 10 mA, the base current is: (1) 10 µA (2) 100 µA (3) 1 A (4) 10 A
Last Answer : In the common–emitter transistor circuit, if the current gain is 100 and the collector current is 10 mA, the base current is: 100 µA
Description : Is the base region much thinner or much wider than the collector and the emitter regions?
Last Answer : yes its thinnerMost of the free electrons that have entered the base do notrecombine with holes because the base is very thin.
Description : The diagram shown in the illustartion represents a/an _____________. EL-0022 A. magnectic amplifier B. common base amplifier C. common collector amplifier D. common emitter amplifier
Last Answer : Answer: D
Description : In the illustrated circuit, the amplifier is connected in what basic configuration? EL-0022 A. common base B. reverse bias, negative feedback C. common emitter D. common collector
Last Answer : Answer: C
Description : In the illustrated circuit, the amplifier is connected in what basic configuration? EL-0045 A. common emitter B. common collector C. darlington paired, capacitor coupled D. common base
Description : In the illustration, the large battery and R(L) are in the circuit to ________. EL-0022 A. forward bias the emitter-base B. reverse bias the emitter-base C. forward bias the emitter/collector D. reverse bias the emitter/collector
Description : As shown in the illustration, which of the elements listed does the line 'B' represent in the basic schematic symbol of a PNP transistor? EL-0068 A. Base B. Emitter C. Cathode D. Collector
Description : The device in figure 'B' shown in the illustration will conduct when the ____________. EL-0067 A. base-emitter is forward biased and the collector-base is reverse biased B. anode-cathode is forward ... is reversed biased D. terminal 1-2 is forward biased and the emitter-terminal 1 is reverse biased
Description : The leads of the device in figure 'B' shown in the illustration are named _________. EL-0065 A. source, gate and drain B. emitter, base and collector C. emitter, base 1 and base 2 D. anode, cathode and gate
Last Answer : Answer: A
Description : Leads on the device in figure 'B' shown in the illustration are named ____________. EL-0067 A. source, gate and drain B. emitter, base and collector C. emitter, base 1 and base 2 D. anode, cathode and gate
Description : Which of the listed components does line 'C' represent for the transistor illustrated? EL-0068 A. Grid B. Plate C. Emitter D. Collector
Description : Which of the following statements correctly applies to transistors? A. NDN and PNP are the two basic types of transistors. B. The three terminals are called the emitter, base, and collector. C. The emitter separates the base and collector. D. The collector separates the emitter and base.
Description : The leads of the device in figure 'A' shown in the illustration are named the _______________. EL-0065 A. source, gate and drain B. emitter, base and collector C. emitter, base 1 and base 2 D. anode, cathode and gate
Description : You are performing an out-of-circuit test of the semi-conductor shown in the illustration. Using an ohmmeter on 'low power' position and with leads properly installed, which of the listed results would you expect the ... lead on 'B' and black lead on 'A'; and a low reading with the leads reversed.
Description : A part of transistor which is heavily doped to produce large number of majority carriers is (a) Emitter (b) Base (c) Collector (d) any of above
Last Answer : (a) Emitter
Description : In the transistor schematic symbol, the arrow ________ (a) located on emitter (b) located on base (c) located on collector (d) points from north to south
Last Answer : a) located on emitter
Description : The operation of a transistor requires ______ (a) Emitter is heated (b) base is heated (c) collector be heated (d) none of above
Last Answer : (d) none of above
Description : In n-p-n transistor, p works as ________ (a) Collector (b) emitter (c) base (d) any of above
Last Answer : c) base
Description : The central region of transistor is called (a) Base (b) emitter (c) collector (d) neutral
Last Answer : (b) emitter
Description : What are the three elements of a bipolar transistor? Are they the: w) grid, plate, cathode x) suppressor, deflector, target y) energizer, controller, terminus z) emitter, base, collector
Last Answer : ANSWER: Z -- EMITTER, BASE, COLLECTOR
Description : If a transistor were operated with emitter and collector interchanged, then 1 .emitter current will increase 2. Collector current will increase 3. Base current will decrease 4. No current flow will take place
Last Answer : If a transistor were operated with emitter and collector interchanged, then Collector current will increase
Description : For the active mode BJT operation (A) Emitter Base Junction is Forward Biased and Collector Base Junction is Forward Biased (B) Emitter Base Junction is Reverse Biased and Collector Base Junction ... Biased (D) Emitter Base Junction is Reverse Biased and Collector Base Junction is Forward Biased
Last Answer : For the active mode BJT operation Emitter Base Junction is Forward Biased and Collector Base Junction is Reverse Biased.
Description : How much must the fpa plate current vary to produce 100- percent modulation in a plate modulator?
Last Answer : Between 0 and nearly two times its unmodulated value.
Description : What is the input current in the common-emitter circuit?
Last Answer : Base current (IB).
Description : What is the output current in the common-collector circuit?
Last Answer : IE.
Description : What percentage of current in an NPN transistor reaches the collector?
Last Answer : 98 percent.
Description : What is the purpose of a modulator in a servo system?
Last Answer : To convert a dc error signal into an ac error signal.
Description : What modulator element controls the rate at which the storage element charges?
Last Answer : The charging impedance.
Description : What type of tube best meets the requirements of a modulator switching element?
Last Answer : Thyratron.
Description : What type of modulator is most commonly used in modern radar systems?
Last Answer : Line-pulsed.
Description : In addition to a flat top, what characteristics must a modulator pulse have?
Last Answer : Steep leading and trailing edges.
Description : What components may be used to build a basic phase modulator?
Last Answer : A phase-shift network such as a variable resistor and capacitor in series
Description : What characteristic of a varactor is used in an fm modulator?
Last Answer : Capacitance.
Description : What circuit section is required in the output of a multivibrator modulator to eliminate unwanted output frequencies?
Last Answer : An LCR filter.
Description : What characteristic of a transistor is varied in a semiconductor-reactance modulator?
Last Answer : Collector-to-emitter capacitance.
Description : How does the reactance-tube modulator impress intelligence onto an rf carrier?
Last Answer : By changing the reactance of an oscillator circuit in consonance with the modulating voltage.
Description : What are the basic components of a thyratron modulator?
Last Answer : ower source, a circuit for storing energy, a circuit for discharging the storage circuit, and a pulse transformer.
Description : What is the primary component for a spark-gap modulator?
Last Answer : Either a fixed spark gap that uses a trigger pulse to ionize the air between the contacts, or a rotary gap that is similar to a mechanical switch.
Description : What type of modulator is the cathode modulator (low- or high-level)?
Last Answer : Low-level.
Description : When is a control-grid modulator used?
Last Answer : In cases when the use of a minimum of af modulator power is desired.