Why will a meter indicate more voltage at the battery terminal when the battery is out of a circuit than when the battery is in a circuit?

Why will a meter indicate more voltage at the battery  terminal when the battery is out of a circuit than when the  battery is in a circuit?
by

1 Answer

Answer :

The internal (source) resistance of the battery will drop some of  the voltage
by

Related questions

In the circuit shown in Fig. 4.63, the terminal voltage of the battery is 6.0 V. Find the current I through the `18 Omega` resistor.

Description : In the circuit shown in Fig. 4.63, the terminal voltage of the battery is 6.0 V. Find the current I through the `18 Omega` resistor.

Last Answer : In the circuit shown in Fig. 4.63, the terminal voltage of the battery is 6.0 V. Find the current I through the `18 Omega` resistor.

A lead-acid battery cell sustaining a short circuit _______. A. will be indicated by lime accumulation on the terminal posts B. will have unusually high cell voltage C. will become excessively heated while being charged D. cannot be completely discharged under load

Description : A lead-acid battery cell sustaining a short circuit _______. A. will be indicated by lime accumulation on the terminal posts B. will have unusually high cell voltage C. will become excessively heated while being charged D. cannot be completely discharged under load

Last Answer : Answer: C

What is the voltage drop across the resistor in an RC charging circuit when the charge on the capacitor is equal to the battery voltage?

Description : What is the voltage drop across the resistor in an RC charging circuit when the charge on the capacitor is equal to the battery voltage?

Last Answer : Zero.

In order to reverse bias in a PN junction, what terminal of a battery is connected to the P material?

Description : In order to reverse bias in a PN junction, what terminal of a battery is connected to the P material?

Last Answer : Negative.

Does low ripple voltage indicate good or bad filtering?

Description : Does low ripple voltage indicate good or bad filtering?

Last Answer : Good.

Does low ripple voltage indicate good or bad filtering?

Description : Does low ripple voltage indicate good or bad filtering?

Last Answer : Good.

What does the voltage rating of a fuse indicate?

Description : What does the voltage rating of a fuse indicate?

Last Answer : The ability of the fuse to quickly extinguish the arc after the fuse element melts and the maximum voltage that cannot jump across the gap of the fuse after the fuse opens.

What type of meter movement reacts to voltage rather than current?

Description : What type of meter movement reacts to voltage rather than current?

Last Answer : Electrostatic.

A lead-acid battery is considered fully charged when the ______________. A. electrolyte gasses freely B. battery charger ammeter indicates a positive reading C. terminal voltage reaches a constant value at a given temperature D. specific gravity of all cells reaches the correct value and no longer increases over a period of 1 to 4 hours

Description : A lead-acid battery is considered fully charged when the ______________. A. electrolyte gasses freely B. battery charger ammeter indicates a positive reading C. terminal voltage reaches a constant value at a ... cells reaches the correct value and no longer increases over a period of 1 to 4 hours

Last Answer : Answer: D

Besides setting up the meter for expected voltage ranges, what must be strictly observed when taking dc voltage readings?

Description : Besides setting up the meter for expected voltage ranges, what must be strictly observed when taking dc voltage readings?

Last Answer : Polarit

What is the only use for the voltage sensitive meter movement?

Description : What is the only use for the voltage sensitive meter movement?

Last Answer : High-voltage measurement.

How is it possible to use a current sensitive meter movement to measure voltage?

Description : How is it possible to use a current sensitive meter movement to measure voltage?

Last Answer : Since the resistance of a meter movement remains the same as the pointer is deflected, the amount of current through the movement is proportional to the voltage applied. Therefore, only the scale of the movement must be changed.

What modification is made to the D’Arsonval meter movement to enable the meter to measure voltage?

Description : What modification is made to the D’Arsonval meter movement to enable the meter to measure voltage?

Last Answer : A multimeter (high resistance) is placed in series with the coil of the meter.

What is one advantage of an out-of-circuit meter when it is compared with an in-circuit meter?

Description : What is one advantage of an out-of-circuit meter when it is compared with an in-circuit meter?

Last Answer : Out-of-circuit meters can be used on more than one electrical or electronic device.

What condition exists when the insertion of a meter into a circuit changes the operation of the circuit?

Description : What condition exists when the insertion of a meter into a circuit changes the operation of the circuit?

Last Answer : Meter-loading.

What component of the D’Arsonval meter movement completes the circuit for current flow to the coil?

Description : What component of the D’Arsonval meter movement completes the circuit for current flow to the coil?

Last Answer : Hairspring.

The terminal voltage of a cell supplying energy to a circuit is usually less than its emf because of the cell's w) size x) internal resistance y) mass z) energy

Description : The terminal voltage of a cell supplying energy to a circuit is usually less than its emf because of the cell's w) size x) internal resistance y) mass z) energy

Last Answer : ANSWER: X -- INTERNAL RESISTANCE

Which of the following actions must be carried out before a voltage tester can be used to test the three line fuses to a three-phase motor? A. The fuses must be removed from the circuit. B. The starter must be placed in the STOP position to stop the motor. C. The three line connections in the motor terminal box must be disconnected and tagged. D. Nothing need be done as long as the motor is running under a light load.

Description : Which of the following actions must be carried out before a voltage tester can be used to test the three line fuses to a three-phase motor? A. The fuses must be removed from the circuit. B. The ... disconnected and tagged. D. Nothing need be done as long as the motor is running under a light load.

Last Answer : Answer: B

If a voltage tester is being used to check for defective fuses in the circuit, shown in the illustration, which of the readings will indicate that fuse #2 is open? EL-0062 A. C-B full voltage B. A-D full voltage C. A-D no voltage D. C-B no voltage

Description : If a voltage tester is being used to check for defective fuses in the circuit, shown in the illustration, which of the readings will indicate that fuse #2 is open? EL-0062 A. C-B full voltage B. A-D full voltage C. A-D no voltage D. C-B no voltage

Last Answer : Answer: C

An open shunt field in a direct current machine may be located by connecting the field circuit to an external power source, equal to the rated field voltage or less, and tested with a voltmeter from _____________. A. one line terminal to each coil lead in succession B. one field coil to each adjacent field coil in turn C. any suitable ground to any available line lead D. any field pole to each field coil lead

Description : An open shunt field in a direct current machine may be located by connecting the field circuit to an external power source, equal to the rated field voltage or less, and tested with a voltmeter from ... C. any suitable ground to any available line lead D. any field pole to each field coil lead

Last Answer : Answer: A

In a simple series circuit, the entire source voltage will drop across ______________. A. the resistor next to the negative terminal B. a short circuit C. the resistor next to the positive terminal D. an open circuit

Description : In a simple series circuit, the entire source voltage will drop across ______________. A. the resistor next to the negative terminal B. a short circuit C. the resistor next to the positive terminal D. an open circuit

Last Answer : Answer: D

The simplest method of controlling the terminal voltage of compound-wound DC generator is with a _____________. A. hand-operated field rheostat connected in series with the shunt field circuit B. separate exciter in a series with the shunt field C. carbon pile regulator in series with the load D. balance coil diverting neutral current through the shunt field

Description : The simplest method of controlling the terminal voltage of compound-wound DC generator is with a _____________. A. hand-operated field rheostat connected in series with the shunt field circuit B. ... in series with the load D. balance coil diverting neutral current through the shunt field

Last Answer : Answer: A

Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at the line terminals (c) Possibility of better protection for the line due to possible use of higher terminal reactants (d) Improvement of power factor at times of moderate and heavy loads (e) Possibility of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Description : Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at ... of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Last Answer : (a) Increase of short-circuit current of the system

Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at the line terminals (c) Possibility of better protection for the line due to possible use of higher terminal reactants (d) Improvement of power factor at times of moderate and heavy loads (e) Possibility of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Description : Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at ... of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Last Answer : (a) Increase of short-circuit current of the system

. A battery uses what method to produce a voltage?

Description : . A battery uses what method to produce a voltage?

Last Answer : Chemical.

At what voltage is a NICAD battery considered to be fully discharged?

Description : At what voltage is a NICAD battery considered to be fully discharged?

Last Answer : At 1.1 volts.

The vertical dotted line connecting the small circular symbols at coordinates '05L', '09L', '13L', '21L', '25L', etc., shown in the illustration, indicate that all _______________. EL-0100 A. contacts are operated by the same relay coil B. screw connections are on terminal board 'TB2' C. wires are grounded at both ends of the line D. wires have a common shield

Description : The vertical dotted line connecting the small circular symbols at coordinates '05L', '09L', '13L', '21L', '25L', etc., shown in the illustration, indicate that all _______________. EL-0100 A. contacts are ... board 'TB2' C. wires are grounded at both ends of the line D. wires have a common shield

Last Answer : Answer: B

Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or load resistor B. noise factor expressed in decibels C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signal D. S/N of an ideal system divided by S/N at the output of the receiver or amplifier under test, both working at the same temperature over the same bandwidth and fed from the same source

Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source

Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals

While measuring frequency response, as the signal generator approaches the lowest and highest frequency the recorder can effectively record, the VTVM reading drops to less than - 3 dB. What does this indicate?

Description : While measuring frequency response, as the signal generator approaches the lowest and highest frequency the recorder can effectively record, the VTVM reading drops to less than - 3 dB. What does this indicate?

Last Answer : The upper and lower limits of the frequency response specification for that tape recorder.

The illustrated circuit is a wheatstone bridge. If the meter 'G' reads 0 with the switch closed then ________. EL-0024 A. the current through R1 - R2 is equal to the current through R3 - Rx B. the voltage across b - d is equal to the voltage of E C. the resistance of Rx is equal to the resistance of R2 D. all the above are true

Description : The illustrated circuit is a wheatstone bridge. If the meter 'G' reads 0 with the switch closed then ________. EL-0024 A. the current through R1 - R2 is equal to the current through R3 - Rx B. the voltage ... of E C. the resistance of Rx is equal to the resistance of R2 D. all the above are true

Last Answer : Answer: A

If the approximate voltage to be measured in a circuit is not known, you should _____________. A. use the lowest voltage range on the voltmeter B. connect the meter in series with the circuit C. only have to calibrate the meter before using it D. use the highest voltage range on the voltmeter

Description : If the approximate voltage to be measured in a circuit is not known, you should _____________. A. use the lowest voltage range on the voltmeter B. connect the meter in series with the circuit C. only have to calibrate the meter before using it D. use the highest voltage range on the voltmeter

Last Answer : Answer: D

To test fuses in an energized circuit, you should use a ____________. A. low voltage light bulb B. megohmmeter C. voltmeter D. resistance meter

Description : To test fuses in an energized circuit, you should use a ____________. A. low voltage light bulb B. megohmmeter C. voltmeter D. resistance meter

Last Answer : Answer: C

When troubleshooting electronic equipment, the FIRST step to be taken before testing the circuit voltage is to _________. A. set the meter to the lowest range B. check the voltage supply from the power source C. remove the suspected component D. check the current flow through the circuit

Description : When troubleshooting electronic equipment, the FIRST step to be taken before testing the circuit voltage is to _________. A. set the meter to the lowest range B. check the voltage supply from the power source C. remove the suspected component D. check the current flow through the circuit

Last Answer : Answer: B

When troubleshooting electronic equipment, you should use a high impedance multimeter ________________. A. to prevent excess current flow through the meter that would damage it B. for AC measurements only and a low resistance meter for DC measurements C. whenever a low impedance meter is not available, regardless of the components being tested D. so as not to load down the circuit and obtain erroneous voltage readings

Description : When troubleshooting electronic equipment, you should use a high impedance multimeter ________________. A. to prevent excess current flow through the meter that would damage it B. for AC measurements only ... being tested D. so as not to load down the circuit and obtain erroneous voltage readings

Last Answer : Answer: D

When taking a voltage measurement, which lead of the voltmeter should you connect to the circuit first?

Description : When taking a voltage measurement, which lead of the voltmeter should you connect to the circuit first?

Last Answer : Ground.

If a half-wave rectifier is added to a half-wave voltage doubler, the resulting circuit is a voltage ___

Description : If a half-wave rectifier is added to a half-wave voltage doubler, the resulting circuit is a voltage ___

Last Answer : Trippler.

Does a filter circuit increase or decrease the average output voltage?

Description : Does a filter circuit increase or decrease the average output voltage?

Last Answer : A filter circuit increases the average output voltage

Does a filter circuit increase or decrease the average output voltage?

Description : Does a filter circuit increase or decrease the average output voltage?

Last Answer : Increase.

What is the relationship of current to voltage in a circuit?

Description : What is the relationship of current to voltage in a circuit?

Last Answer : current increases as voltage increases.

A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?

Description : A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?

Last Answer : (a) 330 volts. (b) E1 = 150 volts. E2 = 180 volts. (c) 1.98 kilowatts. (d) P1 = 900 watts. P2 = 1.08 kilowatts component but in a parallel circuit total current divides among the available paths.

A circuit has a source voltage of 100 volts and two 50-ohm resistors connected in series. If the reference point for this circuit is placed between the two resistors, what would be the voltage at the reference point?

Description : A circuit has a source voltage of 100 volts and two 50-ohm resistors connected in series. If the reference point for this circuit is placed between the two resistors, what would be the voltage at the reference point?

Last Answer : 50 volts.

If the current was increased to 4 amps, what would be the voltage drop across each resistor in the circuit described in question 17?

Description : If the current was increased to 4 amps, what would be the voltage drop across each resistor in the circuit described in question 17?

Last Answer : E1 = 80 volts. E2 = 240 volts. E3 = 320 volts

What is the voltage dropped by each resistor of the circuit described in question 17?

Description : What is the voltage dropped by each resistor of the circuit described in question 17?

Last Answer : E1 = 60 volts. E2 = 180 volts. E3 = 240 volts.

A series circuit consisting of three resistors has a current of 3 amps. If R1 = 20 ohms, R2= 60 ohms, and R 3 = 80 ohms, what is the (a) total resistance and (b) source voltage of the circuit?

Description : A series circuit consisting of three resistors has a current of 3 amps. If R1 = 20 ohms, R2= 60 ohms, and R 3 = 80 ohms, what is the (a) total resistance and (b) source voltage of the circuit?

Last Answer : (a) 160 ohms. (b) 480 ohms

According to Ohm’s law, what happens to circuit current if the applied voltage (a) increases, (b) decreases?

Description : According to Ohm’s law, what happens to circuit current if the applied voltage (a) increases, (b) decreases?

Last Answer : (a) Current increases (b) Current decreases

A circuit is to be designed in which a capacitor must charge to 40 percent of the maximum charging voltage in 200 microseconds. The resistor to be used has a resistance of 40,000 ohms. What size capacitor must be used?

Description : A circuit is to be designed in which a capacitor must charge to 40 percent of the maximum charging voltage in 200 microseconds. The resistor to be used has a resistance of 40,000 ohms. What size capacitor must be used?

Last Answer : 0.1 microfarads 40% from the graph = 0.5

At what instant does the greatest voltage appear across the resistor in a series RC circuit when the capacitor is charging?

Description : At what instant does the greatest voltage appear across the resistor in a series RC circuit when the capacitor is charging?

Last Answer : At the instant of the initiation of the action.

a. Define the term "working voltage" of a capacitor. b. What should be the working voltage of a capacitor in a circuit that is operating at 600 volts?

Description : a. Define the term "working voltage" of a capacitor. b. What should be the working voltage of a capacitor in a circuit that is operating at 600 volts?

Last Answer : a. It is the maximum voltage the capacitor can work without risk of damage. b. 900 volts.