Description : If the current was increased to 4 amps, what would be the voltage drop across each resistor in the circuit described in question 17?
Last Answer : E1 = 80 volts. E2 = 240 volts. E3 = 320 volts
Description : A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?
Last Answer : (a) 330 volts. (b) E1 = 150 volts. E2 = 180 volts. (c) 1.98 kilowatts. (d) P1 = 900 watts. P2 = 1.08 kilowatts component but in a parallel circuit total current divides among the available paths.
Description : What type of resistor should be used in the circuit described in question 12?
Last Answer : A wirewound resistor.
Description : For practical purposes, in a simple series circuit, the source voltage will be dropped across one resistor if it has ______________. A. half the resistance of the other resistor B. a resistance equal to the other C. at least ten times the resistance of the other D. a partial short circuit
Last Answer : Answer: C
Description : A circuit is to be designed in which a capacitor must charge to 40 percent of the maximum charging voltage in 200 microseconds. The resistor to be used has a resistance of 40,000 ohms. What size capacitor must be used?
Last Answer : 0.1 microfarads 40% from the graph = 0.5
Description : What is the voltage drop across the resistor in an RC charging circuit when the charge on the capacitor is equal to the battery voltage?
Last Answer : Zero.
Description : At what instant does the greatest voltage appear across the resistor in a series RC circuit when the capacitor is charging?
Last Answer : At the instant of the initiation of the action.
Description : With a 12 V supply, a silicon diode, and a 370 - ohm resistor in series, what voltage will be dropped across the diode? a) 0.3V b) 0.7V c) 0.9V d) 1.4V
Last Answer : 0.7V
Description : If the load in question 50 requires a voltage of +90 V, what should be the value of the bleeder resistor?
Last Answer : 2 kΩ
Description : A tube has a transconductance of 800 mhos and a load resistor of 50 kohms. When control grid voltage varies by 6 volts, the plate voltage will vary by what amount?
Last Answer : 240 volts.
Description : Which of the following statements concerning a simple parallel resistance circuit is correct? A. The voltage drop across each resistor is the same. B. The total current flow equals the reciprocal ... resistances. D. The total voltage equals the sum of the individual voltages across each resistance.
Last Answer : Answer: A
Description : 9 leds each of 1 volt drop is series with 9 volt battery , do we need a resistor?(SMD leds) I have seen some smd leds without resistor !
Last Answer : We connect resistor to limit the current. So, it depends upon the current rating of the LED, which is provided by manufacturer.
Last Answer : Req= (1/1200 +1/560 + 1/2.1)^-1 = 2.1 ohms RT= 2.1 + 7.8 = 9.9 ohms IT = V/R = 24/9.9 = 2.4 A Veq= R I = 2.1 2 ... 7.8 = 12.096 w = 44.928 w _________________________________________ By: Ellis-Junior Kamatjipose [email protected]
Description : What name is given to a resistor used to replace the normal load in a circuit?
Last Answer : Dummy load or dummy antenna.
Description : What term identifies a single resistor that represents total resistance of a complex circuit?
Last Answer : Equivalent resistor or Req.
Description : What is the power used in a circuit that has 10 amperes of current through a 10-ohm resistor?
Last Answer : 1 kilowatt.
Description : What is the RC time constant of a series RC circuit that contains a 12-megohm resistor and a 12-microfarad capacitor?
Last Answer : 144 seconds (t=R x C)
Description : The same resistor mentioned in question 63 has a yellow fifth band. What does this signify?
Last Answer : The resistor’s chance of failure is 0.001 percent for 1000 hours of operation.
Description : Four equal resistors are connected in parallel, each resistor has an ohmic value of 100 ohms, what is the equivalent resistance?
Last Answer : 25 ohms
Description : In the circuit shown the voltage drop across the `15Omega` resistor is `30 V` having the polarity as indicated. The ratio of potential difference acro
Last Answer : In the circuit shown the voltage drop across the `15Omega` resistor is `30 V` having the ... difference across `5Omega` and resistance `R` is
Description : In the circuit shown in Fig. 4.63, the terminal voltage of the battery is 6.0 V. Find the current I through the `18 Omega` resistor.
Last Answer : In the circuit shown in Fig. 4.63, the terminal voltage of the battery is 6.0 V. Find the current I through the `18 Omega` resistor.
Description : In the illustrated motor controller circuit, which statment is true? EL-0023 A. The high and low speed lights operate at less than line voltage with a resistor in series. B. This controller can be ... . The wattage of the high speed light must be greater than the wattage of the low speed light.
Description : What would be the voltage drop across the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts
Description : In a simple series circuit, the entire source voltage will drop across ______________. A. the resistor next to the negative terminal B. a short circuit C. the resistor next to the positive terminal D. an open circuit
Last Answer : Answer: D
Description : The conversion of the throttle command voltage to the signal necessary to achieve the desired shaft RPM is accomplished by the _____________. A. ahead or astern function generator of the ... circuit C. operational amplifiers in the autorotation circuit D. long time constant amplifier circuit
Description : A series circuit consists of a two ohm RESISTOR and a one ohm INDUCTOR. The relationship between current and voltage is: w) current will lag by 30 degrees. x) current will lag by 26 degrees. y) current will lead by 26 degrees. z) current will lead by 30 degrees.
Last Answer : ANSWER: X -- CURRENT WILL LAG BY 26 DEGREES.
Description : An LED is operated on a 12 volt automobile circuit. The voltage drop across the LED is 2 volts and the current must be limited to 50 milliamps to prevent its overheating and destruction. What size resistor must be used? w) 60 ohms x) 100 ohms y) 120 ohms z) 200 ohms
Last Answer : ANSWER: Z -- 200 OHMS
Description : Source transformation Replace the circuit with voltage source in series with a single resistor
Last Answer : Source transformation Replace the circuit with voltage source in series with a single resistor
Description : Average power dissipated in resistor if sinusoidal p.d of peak value 25 V is connected across a 20 Ω resistor is A. 15.6 W B. 15 W C. 16 W D. 17 W
Last Answer : 15.6 W
Description : A resistor is handed to you for identification with the following color code: the first band is blue, followed by gray, green, gold, and brown. What is the resistor’s value?
Last Answer : 6,800,000 ohms (6.8 mega ohms), with 5% tolerance, and a 1% reliability level.
Description : A carbon resistor has the following color bands: The first band is yellow, followed by violet, yellow, and silver. What is the ohmic value of the resistor?
Last Answer : 470,000 ohms (470 kilo ohms).
Description : A carbon resistor has a resistance of 50 ohms, and a tolerance of 5 percent. What are the colors of bands one, two, three, and four, respectively?
Last Answer : The bands are green, black, black, and gold.
Description : . Which type of variable resistor should you select for controlling a large amount of current?
Last Answer : The rheostat.
Description : What type resistor should be used to overcome the disadvantages of the carbon resistor?
Last Answer : The wirewound resistor.
Description : What does the wattage rating of a resistor indicate?
Last Answer : Its ability to dissipate heat
Description : What is the time constant of the resistor and capacitor in a peak detector for pam?
Last Answer : At least 10 times the interpulse period.
Description : What factors determine the value of the multiplier resistor?
Last Answer : The current required for full-scale deflection, and the range of the voltage to be measured.
Description : Find the equivealent resistance of the circuit shown in Fig. 4.61 between the points P and Q. Each resistor has a resistance r.
Last Answer : Find the equivealent resistance of the circuit shown in Fig. 4.61 between the points P and Q. Each resistor has a resistance r.
Description : Find the equivalent resistance of the circuit shown in Fig.4.60 between the points A and B. Each resistor has a resistance r.
Last Answer : Find the equivalent resistance of the circuit shown in Fig.4.60 between the points A and B. Each resistor has a resistance r.
Description : When troubleshooting a console circuit card suspected of being faulty, first check operating voltages, clean the card and then _________________. A. make sure wired connections and push-on connectors ... circuit traces with an ohmmeter D. measure the gain of each transistor or integrated circuit
Description : The total power consumed in a parallel circuit is __________. A. the sum of the powers used in each load (resistor) divided by the number of loads B. always less than the power used in the smallest ... of the powers used in each individual load D. never more than the power used in the largest load
Description : The total power used up in a series circuit is ___________. A. the sum of the powers used in each load (resistor) divided by the number of loads B. the sum of the powers used in each load C. always less than the power used in the smallest load D. never more than the power used in largest load
Last Answer : Answer: B
Description : Which of the following methods cannot be used to increase the bandwidth for cascaded RF amplifier stages? A) Wave traps in each stage B) Stagger tuning C) A shunt damping resistor across each tuned circuit D) Doubled tuned transformers with tighter coupling
Last Answer : A) Wave traps in each stage
Description : When a voltage of 124 VDC is applied to the illustrated circuit with a resistance of 17.8 ohms the current will be ________. EL-0018 A. 0.143 amps B. 2.555 amps C. 6.966 amps D. 141.8 milliamps
Description : When a voltage of 112 VDC is applied to the circuit illustrated with a resistance of 17.8 ohms the current will be________. EL-0018 A. .158 amps B. 5.82 amps C. 6.29 amps D. 129.8m amps
Description : When a voltage of 110 VDC is applied to the illustrated circuit with a resistance of 17.8 ohms the current will be________. EL-0018 A. 2.88 amps B. 6.18 amps C. 127.8m amps D. 161 amps
Description : When a voltage of 110 VDC is applied to the circuit illustrated with a resistance of 12 ohms the current will be________. EL-0018 A. .11 amps B. 1.31 amps C. 9.17 amps D. 122m amps
Description : When a voltage of 115 VDC is applied to the illustrated circuit with a resistance of 17.8 ohms the current will be _______. EL-0018 A. 0.154 amps B. 2.755 amps C. 6.46 amps D. 0.1328 amps
Description : In the illustration, the diode between terminals 16 and 17 is to _________. EL-0046 A. act as a short circuit for the sensing coil when CEMF is applied B. insure that the voltage across the coil does not exceed 9 volts C. improve response time D. act as a filter to prevent hunting
Description : When a voltage of 95 VDC is applied to the circuit illustrated with a resistance of 17.8 ohms the current will be________. EL-0018 A. .187 amps B. 3.34 amps C. 5.34 amps D. 112.8m amps