How many units are in a tty signal and what are they?

How many units are in a tty signal and what are they?
by

1 Answer

Answer :

Intelligence (5), start (1), stop (1).
by

Related questions

What does the color red indicate on a tty patch panel?

Description : What does the color red indicate on a tty patch panel?

Last Answer : It handles classified information.

A receive tty set provides outputs in what formats?

Description : A receive tty set provides outputs in what formats?

Last Answer : Page-size copy paper and perforated tape.

Most Navy tty sets operate at what speeds?

Description : Most Navy tty sets operate at what speeds?

Last Answer : 60, 75, or 100 wpm.

What is a TTY adaptor used for?

Description : What is a TTY adaptor used for?

Last Answer : answer:It is a device for the deaf to communicate via phone. Basically 'texting' each other on a specific machine about the size of a laptop these days. Maybe the adapter allows you to call/ ... via pager/ hearing through relay service through our pagers or computer. http://en.wikipedia.org/wiki/TTY

What is TTY?

Description : What is TTY?

Last Answer : I don’t know what it stands for but I believe it is an option for the hard of hearing or deaf.

What is the full form of 'TTY' ? -How To ?

Description : What is the full form of 'TTY' ? -How To ?

Last Answer : The full form of 'TTY' is Tele Typewriter

If you are to use [Control-c] as the interrupt key instead of [Del], then you will have to use A. tty ^c B. stty intr \^c C. stty echoe D. stty echo \^a E. None of the above

Description : If you are to use [Control-c] as the interrupt key instead of [Del], then you will have to use A. tty ^c B. stty intr \^c C. stty echoe D. stty echo \^a E. None of the above

Last Answer : B. stty intr \^c

Sound waves transmitted from a source are sometimes weak when they reach the detector. What instrument is needed to boost the weak signal?

Description : Sound waves transmitted from a source are sometimes weak when they reach the detector. What instrument is needed to boost the weak signal?

Last Answer : An amplifier.

What is the reference point for alignment of all synchro units?

Description : What is the reference point for alignment of all synchro units?

Last Answer : The voltmeter method.

What method is used to prevent oscillations in large synchro units?

Description : What method is used to prevent oscillations in large synchro units?

Last Answer : Mechanical damping.

What are the three units of measure most commonly used when referring to af power measurements?

Description : What are the three units of measure most commonly used when referring to af power measurements?

Last Answer : DB, dBm, and vu.

A transmission line is said to have distributed constants of inductance, capacitance, and resistance along the line. What units of measurement are used to express these constants?

Description : A transmission line is said to have distributed constants of inductance, capacitance, and resistance along the line. What units of measurement are used to express these constants?

Last Answer : Inductance is expressed in micro henrys per unit length, capacitance is expressed in picofarads per unit length, and resistance is expressed in ohms per unit length.

Two layers of arimid yarn strength members encase the OFCC units. Why are these strength members stranded in opposing directions?

Description : Two layers of arimid yarn strength members encase the OFCC units. Why are these strength members stranded in opposing directions?

Last Answer : To minimize microbending of the fibers.

What are the major differences between magnetic tape units?

Description : What are the major differences between magnetic tape units?

Last Answer : The speed at which the tape is moved past the read/write head and the density of the recorded information.

What are the major differences between magnetic tape units?

Description : What are the major differences between magnetic tape units?

Last Answer : The speed at which the tape is moved past the read/write head and the density of the recorded information.

A positive damper clamps which extremity of the output signal to 0 volts?

Description : A positive damper clamps which extremity of the output signal to 0 volts?

Last Answer : Most negative.

How can a series-positive limiter be modified to limit unwanted negative portions of the input signal?

Description : How can a series-positive limiter be modified to limit unwanted negative portions of the input signal?

Last Answer : Biasing.

What components form the input-signal-developing impedance for the amplifier?

Description : What components form the input-signal-developing impedance for the amplifier?

Last Answer : C2 and the secondary of T1.

If the input-signal-developing impedance of an amplifier is increased, what is the effect on the gain?

Description : If the input-signal-developing impedance of an amplifier is increased, what is the effect on the gain?

Last Answer : The gain increases.

What is the name of the device that provides an increase in current, voltage, or power of a signal without appreciably altering the original signal?

Description : What is the name of the device that provides an increase in current, voltage, or power of a signal without appreciably altering the original signal?

Last Answer : Amplifier.

. When you select the time base to display a signal, should the time base be the same, higher, or lower than the input signal?

Description : . When you select the time base to display a signal, should the time base be the same, higher, or lower than the input signal?

Last Answer : Lower.

In applications where electronic waveforms are displayed on a CRT screen, the input signal is normally applied to what CRT element?

Description : In applications where electronic waveforms are displayed on a CRT screen, the input signal is normally applied to what CRT element?

Last Answer : The vertical-deflection plate.

What signal causes FF2 to toggle?

Description : What signal causes FF2 to toggle?

Last Answer : Q output of FF 1 going LOW.

In a circuit such as that shown in figure 3-16, if R1 has a value of 50 ohms and R2 has a value of 250 ohms and the input signal has a value of +10 millivolts, what is the value of the output signal?

Description : In a circuit such as that shown in figure 3-16, if R1 has a value of 50 ohms and R2 has a value of 250 ohms and the input signal has a value of +10 millivolts, what is the value of the output signal?

Last Answer : 60 millivolts.

In a circuit such as that shown in figure 3-15, if R1 has a value of 100 ohms and R2 has a value of 1 kilohm and the input signal is at a value of + 5 millivolts, what is the value of the output signal?

Description : In a circuit such as that shown in figure 3-15, if R1 has a value of 100 ohms and R2 has a value of 1 kilohm and the input signal is at a value of + 5 millivolts, what is the value of the output signal?

Last Answer : 50 millivolts.

In the inverting configuration when the noninverting input is grounded, the inverting input is at (signal, virtual) ground

Description : In the inverting configuration when the noninverting input is grounded, the inverting input is at (signal, virtual) ground

Last Answer : Virtual.

In the inverting configuration, what is the voltage (for all practical purposes) at the inverting input to the operational amplifier if the input signal is a 1-volt, peak-to-peak sine wave?

Description : In the inverting configuration, what is the voltage (for all practical purposes) at the inverting input to the operational amplifier if the input signal is a 1-volt, peak-to-peak sine wave?

Last Answer : 0 volts.

In the inverting configuration, the input signal is applied to the (a) (inverting, noninverting) input and the feedback signal is applied to the (b) (inverting, noninverting) input.

Description : In the inverting configuration, the input signal is applied to the (a) (inverting, noninverting) input and the feedback signal is applied to the (b) (inverting, noninverting) input.

Last Answer : a. Inverting. b. Inverting.

select the correct response from the choices given in the parentheses. Q-20. In a closed-loop configuration the output signal is determined by (the input signal, the feedback signal, both).

Description : select the correct response from the choices given in the parentheses. Q-20. In a closed-loop configuration the output signal is determined by (the input signal, the feedback signal, both).

Last Answer : Both the input signal and the feedback signal.

If the input signals are 180 degrees out of phase with each other and a combined output is taken between the two output terminals, what will the amplitude of the combined output signal be?

Description : If If the input signals are 180 degrees out of phase with each other and a combined output is taken between the two output terminals, what will the amplitude of the combined output signal be?

Last Answer : 200 millivolts.

If the single-input, differential-output, differential amplifier has an output signal taken between the two output terminals, what will the peak-to-peak amplitude of this combined output be?

Description : If the single-input, differential-output, differential amplifier has an output signal taken between the two output terminals, what will the peak-to-peak amplitude of this combined output be?

Last Answer : 200 millivolts. A-18. a. Differential amplifier

If the two input signals to a difference amplifier are equal in amplitude but neither in phase nor 180 degrees out of phase, what will the output signal be?

Description : If the two input signals to a difference amplifier are equal in amplitude but neither in phase nor 180 degrees out of phase, what will the output signal be?

Last Answer : . A different shape than the input signals but larger in amplitude.

If only one input signal is used with a difference amplifier, what will the output signal be?

Description : If only one input signal is used with a difference amplifier, what will the output signal be?

Last Answer : Equal in shape and frequency to the input signal; larger in amplitude than the input signal; half as large in amplitude as when two input signals were used that were 180 degrees out of phase.

If the two input signals to a difference amplifier are equal in amplitude and 180 degrees out of phase, what will the output signal be?

Description : If the two input signals to a difference amplifier are equal in amplitude and 180 degrees out of phase, what will the output signal be?

Last Answer : Equal in shape and frequency to each input signal and larger in amplitude by two times than

. If the two input signals of a difference amplifier are in phase and equal in amplitude, what will the output signal be?

Description : . If the two input signals of a difference amplifier are in phase and equal in amplitude, what will the output signal be?

Last Answer : No output (the signals will "cancel out").

An error signal is the difference between what two quantities fed to the CT (error detector)?

Description : An error signal is the difference between what two quantities fed to the CT (error detector)?

Last Answer : Input signal and feedback.

When measuring receiver sensitivity, what quantities must you add to the dBm reading obtained on the signal generator or test set?

Description : When measuring receiver sensitivity, what quantities must you add to the dBm reading obtained on the signal generator or test set?

Last Answer : Attenuations of the directional coupler and the connecting cable.

You determine receiver sensitivity by measuring the power level of what signal?

Description : You determine receiver sensitivity by measuring the power level of what signal?

Last Answer : Minimum discernible signal (mds).

If a transmitting antenna is placed close to the ground, how should the antenna be polarized to give the greatest signal strength?

Description : If a transmitting antenna is placed close to the ground, how should the antenna be polarized to give the greatest signal strength?

Last Answer : Vertically polarized.

The display screen of a spectrum analyzer presents a graphic plot of what two signal characteristics?

Description : The display screen of a spectrum analyzer presents a graphic plot of what two signal characteristics?

Last Answer : Power and frequency.

When a large signal and a small signal are applied to a lin log amplifier at the same time, what is the effect on the small signal?

Description : When a large signal and a small signal are applied to a lin log amplifier at the same time, what is the effect on the small signal?

Last Answer : Amplification is reduced.

What signal is used to synchronize the coherent oscillator to a fixed phase relationship with the transmitted pulse?

Description : What signal is used to synchronize the coherent oscillator to a fixed phase relationship with the transmitted pulse?

Last Answer : Coho lock pulse.

Which component of the receiver produces the signal that is mixed with the received signal to produce the IF signal?

Description : Which component of the receiver produces the signal that is mixed with the received signal to produce the IF signal?

Last Answer : Local oscillator.

In the power amplifier shown in figure 2-10, what two signals are mixed to produce the output signal? In the power amplifier shown in figure 2-10, what two signals are mixed to produce the output signal?

Description : In the power amplifier shown in figure 2-10, what two signals are mixed to produce the output signal?

Last Answer : Local oscillator and coherent oscillator.

what causes the initial and final pulses on the receiver output signal?

Description : what causes the initial and final pulses on the receiver output signal?

Last Answer : Leakage from the duplexer.

Radar altimeters use what type of transmission signal?

Description : Radar altimeters use what type of transmission signal?

Last Answer : Frequency modulated (fm).

What happens when a frequency meter is adjusted to the frequency of the signal being measured?

Description : What happens when a frequency meter is adjusted to the frequency of the signal being measured?

Last Answer : Power is absorbed by the frequency meter cavity; and a pronounced dip in power, at the output, will be observed.

Does a rectifier tube conduct on the positive or negative alternation of the input signal?

Description : Does a rectifier tube conduct on the positive or negative alternation of the input signal?

Last Answer : Positive.

Which components provide the regenerative feedback signal in the phase-shift oscillator?

Description : Which components provide the regenerative feedback signal in the phase-shift oscillator?

Last Answer : Resistor-capacitor networks.

What type of feedback aids an input signal?

Description : What type of feedback aids an input signal?

Last Answer : Regenerative or positive