Description : In the inverting configuration, the input signal is applied to the (a) (inverting, noninverting) input and the feedback signal is applied to the (b) (inverting, noninverting) input.
Last Answer : a. Inverting. b. Inverting.
Description : In the inverting configuration, what is the voltage (for all practical purposes) at the inverting input to the operational amplifier if the input signal is a 1-volt, peak-to-peak sine wave?
Last Answer : 0 volts.
Description : select the correct response from the choices given in the parentheses. Q-20. In a closed-loop configuration the output signal is determined by (the input signal, the feedback signal, both).
Last Answer : Both the input signal and the feedback signal.
Description : The signal to the circuit on card 'A0AA2' at coordinate '29Q' shown in the illustration is on the ____________. EL-0099 A. non-inverting input at pin '20' B. inverting input at pin '16' C. non-inverting input at pin '14' D. inverting input at pin '46'
Last Answer : Answer: B
Description : Which transistor configuration has the highest input resistance?
Last Answer : Common collector.
Description : Which transistor configuration provides a phase reversal between the input and output signals?
Last Answer : Common emitter.
Description : In an inverting amplifier the non-inverting input (+) is connected to A. 1 V line B. 0 V line C. 2 V line D. 3 V line
Last Answer : 0 V line
Description : In inverting amplifier, the phase difference between input and output voltages must be A. 30° B. 45° C. 90° D. 180°
Last Answer : 180°
Description : For non-inverting amplifier the input and output is A. out of phase B. in phase C. have phase difference of 180° D. have phase difference of 90°
Last Answer : in phase
Description : Why are the 2 input terminals of an op-amp are called as inverting & non-inverting terminals?
Last Answer : Ans-Because if we give input to one input means that will produce the same phase output where as the other(Inverting) pin produce 180 degree phase shifted output.
Description : Why We Giving Input To Electronic Amplifier In Inverting Pin? What Is The Reason Behind That?
Last Answer : if we need a phase shift than we give input n inverting pin or when we need to boost signal at higher level, i.e; using cascade stages of amplification(even) than we also use inverting pin.
Description : Non-inverting amplifier circuits have _______ (a) Very high input impedance (b) very low input impedance (c) low output impedance (d) none of above
Last Answer : (a) Very high input impedance
Last Answer : If ground is applied to the (+) terminal of an inverting op-amp, the (–) terminal will Be virtual ground.
Description : How can a series-positive limiter be modified to limit unwanted negative portions of the input signal?
Last Answer : Biasing.
Description : What components form the input-signal-developing impedance for the amplifier?
Last Answer : C2 and the secondary of T1.
Description : If the input-signal-developing impedance of an amplifier is increased, what is the effect on the gain?
Last Answer : The gain increases.
Description : . When you select the time base to display a signal, should the time base be the same, higher, or lower than the input signal?
Last Answer : Lower.
Description : In applications where electronic waveforms are displayed on a CRT screen, the input signal is normally applied to what CRT element?
Last Answer : The vertical-deflection plate.
Description : In a circuit such as that shown in figure 3-16, if R1 has a value of 50 ohms and R2 has a value of 250 ohms and the input signal has a value of +10 millivolts, what is the value of the output signal?
Last Answer : 60 millivolts.
Description : In a circuit such as that shown in figure 3-15, if R1 has a value of 100 ohms and R2 has a value of 1 kilohm and the input signal is at a value of + 5 millivolts, what is the value of the output signal?
Last Answer : 50 millivolts.
Description : If If the input signals are 180 degrees out of phase with each other and a combined output is taken between the two output terminals, what will the amplitude of the combined output signal be?
Last Answer : 200 millivolts.
Description : If the single-input, differential-output, differential amplifier has an output signal taken between the two output terminals, what will the peak-to-peak amplitude of this combined output be?
Last Answer : 200 millivolts. A-18. a. Differential amplifier
Description : If the two input signals to a difference amplifier are equal in amplitude but neither in phase nor 180 degrees out of phase, what will the output signal be?
Last Answer : . A different shape than the input signals but larger in amplitude.
Description : If only one input signal is used with a difference amplifier, what will the output signal be?
Last Answer : Equal in shape and frequency to the input signal; larger in amplitude than the input signal; half as large in amplitude as when two input signals were used that were 180 degrees out of phase.
Description : If the two input signals to a difference amplifier are equal in amplitude and 180 degrees out of phase, what will the output signal be?
Last Answer : Equal in shape and frequency to each input signal and larger in amplitude by two times than
Description : . If the two input signals of a difference amplifier are in phase and equal in amplitude, what will the output signal be?
Last Answer : No output (the signals will "cancel out").
Description : Does a rectifier tube conduct on the positive or negative alternation of the input signal?
Last Answer : Positive.
Description : What type of feedback aids an input signal?
Last Answer : Regenerative or positive
Description : The pump signal frequency must be of what value when compared to the input signal of a simple parametric amplifier?
Last Answer : Exactly double the input frequency.
Description : When measuring harmonic distortion, you set the signal generator to input a 15-kHz test signal. To what frequency should you set the wave analyzer?
Last Answer : 45 kHz.
Description : Two tape recorders have signal-to-noise ratios (SNRs) of 25-dB RMS and 35-dB RMS respectively. Which of the SNRs can record and reproduce the widest range of input signals and why?
Last Answer : 35-dB RMS because the highest SNR can always record and reproduce the widest range of input signals.
Description : What are three advantages of adding an ac bias voltage to the input signal instead of adding a fixed dc bias voltage?
Last Answer : a. Reproduces a stronger output signal. b. Greatly improves the SNR. c. Greatly reduces the natural tape hiss.
Description : Why does adding dc vice ac bias voltage to the input signal result in a poor signal-to-noise ratio (SNR)?
Last Answer : With dc bias, the SNR is poor because only a small portion of the magnetism curve is straight enough to use, thus the output signal is weak compared with the natural tape hiss.
Description : How does dc bias added to the input signal correct the distortion in the output signal?
Last Answer : The dc bias moves the input signal away from the step in the magnetism curve. This prevents the input signal from crossing the zero-point of the magnetism curve.
Description : rid-leak biasing in effect rectifies the input ac signal. What feature
Last Answer : Unequal charge and discharge paths of the coupling capacitor Cc.
Description : When a circuit uses cathode biasing, the input signal can cause varia
Last Answer : Through the use of a bypass capacitor
Description : Which component in figure 3-7 develops the af signal at the input?
Last Answer : R1.
Description : If the output of a circuit needs to be a complete representation of one-half of the input signal, what class of operation is indicated?
Last Answer : Class B operation.
Description : Does an amplifier actually change an input signal? Why or why not?
Last Answer : No, the input signal is unchanged, the output signal is controlled by the input signal but does not effect the actual input signal.
Description : If a transmitting antenna is placed close to the ground, how should the antenna be polarized to give the greatest signal strength?
Last Answer : Vertically polarized.
Description : The outer conductor of a coaxial transmission line is always grounded at the A. Input only B. Input and output C. Output only D. Point of high SWR
Last Answer : B. Input and output
Description : One input terminal of high gain comparator circuit is grounded and a sinusoidal voltage is applied to the other input. The output of comparator will be___________.
Last Answer : One input terminal of high gain comparator circuit is grounded and a sinusoidal voltage is applied to the other input. The output of comparator will be a square wave.
Description : In the system shown in the illustration, the station at section I is unable to signal any other station nor is any other station able to signal the station in section I. The station can, however, ring ... only a single station to respond to itself. D. The switch at component 'C' is stuck open.
Description : One of the following prevents a transmitter from emitting a signal that interferes with other stations on frequency during the test. A. Use of low height antenna B. Use of grounded antenna C. Use of dummy antenna D. Use of shielded antenna radiator
Last Answer : C. Use of dummy antenna
Description : How can I calculate the ground reaction of a grounded ship？?
Last Answer : ‘reaction’? What do you mean? When it tips? If the hull tears?
Description : According to Coast Guard Regulations (46 CFR), the talking and calling circuits of a sound powered telephone system must be _____________. A. intrinsically safe B. independent of each other C. independently grounded D. connected to a common ground
Description : In preparing to take insulation resistance readings on a main generator, the windings should be grounded for about 15 minutes prior to the test to _____________. A. allow accurate zeroing of the meter ... the windings D. help the windings to cool to the same temperature as the ground test connection
Last Answer : Answer: C
Description : If all of the ground detection lamps burn with equal brilliance, whether the test button is depressed or released, then ___________. A. no grounds exist B. all phases are grounded C. all lamps show a ground D. all of the above
Last Answer : Answer: A
Description : In the illustrated test, if the lamp fails to light on any of the three windings then _________. EL-0027 A. all three windings are grounded and the motor should be sent out for repair B. ... the motor controller and the controller should be checked D. the test should be redone at a higher voltage
Description : A voltmeter located on a control panel has been operating correctly for six months, suddenly burns out. After removing it, it is found that neither side of the meter has been grounded. When ... side and the ground C. installed exactly as the old installation D. grounded to the positive side