If the input-signal-developing impedance of an amplifier is increased, what is the effect on the gain?

If the input-signal-developing impedance of an amplifier is  increased, what is the effect on the gain?
by

1 Answer

Answer :

The gain increases.
by

Related questions

What components form the input-signal-developing impedance for the amplifier?

Description : What components form the input-signal-developing impedance for the amplifier?

Last Answer : C2 and the secondary of T1.

If the output impedance of an amplifier circuit is decreased, what is the effect on the gain?

Description : If the output impedance of an amplifier circuit is decreased, what is the effect on the gain?

Last Answer : The gain decreases.

Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1.0MHz and the temperature is 20˚C, and that the receiver is connected to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

In the inverting configuration, what is the voltage (for all practical purposes) at the inverting input to the operational amplifier if the input signal is a 1-volt, peak-to-peak sine wave?

Description : In the inverting configuration, what is the voltage (for all practical purposes) at the inverting input to the operational amplifier if the input signal is a 1-volt, peak-to-peak sine wave?

Last Answer : 0 volts.

If the single-input, differential-output, differential amplifier has an output signal taken between the two output terminals, what will the peak-to-peak amplitude of this combined output be?

Description : If the single-input, differential-output, differential amplifier has an output signal taken between the two output terminals, what will the peak-to-peak amplitude of this combined output be?

Last Answer : 200 millivolts. A-18. a. Differential amplifier

If the two input signals to a difference amplifier are equal in amplitude but neither in phase nor 180 degrees out of phase, what will the output signal be?

Description : If the two input signals to a difference amplifier are equal in amplitude but neither in phase nor 180 degrees out of phase, what will the output signal be?

Last Answer : . A different shape than the input signals but larger in amplitude.

If only one input signal is used with a difference amplifier, what will the output signal be?

Description : If only one input signal is used with a difference amplifier, what will the output signal be?

Last Answer : Equal in shape and frequency to the input signal; larger in amplitude than the input signal; half as large in amplitude as when two input signals were used that were 180 degrees out of phase.

If the two input signals to a difference amplifier are equal in amplitude and 180 degrees out of phase, what will the output signal be?

Description : If the two input signals to a difference amplifier are equal in amplitude and 180 degrees out of phase, what will the output signal be?

Last Answer : Equal in shape and frequency to each input signal and larger in amplitude by two times than

. If the two input signals of a difference amplifier are in phase and equal in amplitude, what will the output signal be?

Description : . If the two input signals of a difference amplifier are in phase and equal in amplitude, what will the output signal be?

Last Answer : No output (the signals will "cancel out").

The pump signal frequency must be of what value when compared to the input signal of a simple parametric amplifier?

Description : The pump signal frequency must be of what value when compared to the input signal of a simple parametric amplifier?

Last Answer : Exactly double the input frequency.

Does an amplifier actually change an input signal? Why or why not?

Description : Does an amplifier actually change an input signal? Why or why not?

Last Answer : No, the input signal is unchanged, the output signal is controlled by the input signal but does not effect the actual input signal.

When a large signal and a small signal are applied to a lin log amplifier at the same time, what is the effect on the small signal?

Description : When a large signal and a small signal are applied to a lin log amplifier at the same time, what is the effect on the small signal?

Last Answer : Amplification is reduced.

Non-inverting amplifier circuits have _______ (a) Very high input impedance (b) very low input impedance (c) low output impedance (d) none of above

Description : Non-inverting amplifier circuits have _______ (a) Very high input impedance (b) very low input impedance (c) low output impedance (d) none of above

Last Answer : (a) Very high input impedance

rid-leak biasing in effect rectifies the input ac signal. What feature

Description : rid-leak biasing in effect rectifies the input ac signal. What feature

Last Answer : Unequal charge and discharge paths of the coupling capacitor Cc.

When compared to the JFET, what is the input impedance of the MOSFET?

Description : When compared to the JFET, what is the input impedance of the MOSFET?

Last Answer : The MOSFET has a higher input impedance.

The input impedance of your test equipment should exceed the impedance of the circuit under test by what ratio?

Description : The input impedance of your test equipment should exceed the impedance of the circuit under test by what ratio?

Last Answer : 10 to 1

What impedance relationship between the output of one circuit and the input of another circuit will provide the maximum power transfer?

Description : What impedance relationship between the output of one circuit and the input of another circuit will provide the maximum power transfer?

Last Answer : Equal impedance.

Operational amplifiers, used primarily in analog circuits, are characterized by ____________. A. high input impedance, high gain and low output impedance B. high input impedance, high gain and high output impedance C. low input impedance, low gain and high output impedance D. low input impedance, high gain and low output impedance

Description : Operational amplifiers, used primarily in analog circuits, are characterized by ____________. A. high input impedance, high gain and low output impedance B. high input impedance, high gain and high output ... gain and high output impedance D. low input impedance, high gain and low output impedance

Last Answer : Answer: A

Common base configuration is little used because A) It has low input impedance B) It has high input impedance C) It does not heat up D) It has very high gain.

Description : Common base configuration is little used because A) It has low input impedance B) It has high input impedance C) It does not heat up D) It has very high gain.

Last Answer : A) It has low input impedance

Compare BJT common base configuration with common collector configuration on the basis of (i) Current gain (ii) Voltage gain (iii) Input impedance (iv) Output impedance

Description : Compare BJT common base configuration with common collector configuration on the basis of (i) Current gain (ii) Voltage gain (iii) Input impedance (iv) Output impedance

Last Answer : Parameter Common Base Common Collector Current gain Low (About 1) High (1+β) Voltage gain High 1  Input impedance  Low High Output impedance High Low

If the impedance of the choke is increased, will the ripple amplitude increase or decrease?

Description : If the impedance of the choke is increased, will the ripple amplitude increase or decrease?

Last Answer : Decrease.

What two methods are used to compensate for the problems that cause low gain in an rf amplifier?

Description : What two methods are used to compensate for the problems that cause low gain in an rf amplifier?

Last Answer : . RF transformers are used and the transistor is neutralized.

If current gain is required from an rf amplifier, what type of component should be used as an output coupling element?

Description : If current gain is required from an rf amplifier, what type of component should be used as an output coupling element?

Last Answer : A step-down transformer.

If the unity-gain point of the operational amplifier used in question 24 is 500 kilohertz, what is the bandwidth of the circuit?

Description : If the unity-gain point of the operational amplifier used in question 24 is 500 kilohertz, what is the bandwidth of the circuit?

Last Answer : 50 kilohertz (Gain = 10; Gain-Bandwidth Product = 500,000) 500,000(Hz)

What happens to the overall gain of a lin-log amplifier as each stage saturates?

Description : What happens to the overall gain of a lin-log amplifier as each stage saturates?

Last Answer : Decreases.

In the basic transistor amplifier discussed earlier, what is the relationship between the polarity of the input and output signals?

Description : In the basic transistor amplifier discussed earlier, what is the relationship between the polarity of the input and output signals?

Last Answer : The signals are opposite in polarity or 180 degrees out of phase with each other.

The input and output signals of a JFET amplifier have what phase relationship?

Description : The input and output signals of a JFET amplifier have what phase relationship?

Last Answer : They are 180 degrees out of phase.

What is used to bias a magnetic amplifier so that the control winding remains free to accept control (input) signals?

Description : What is used to bias a magnetic amplifier so that the control winding remains free to accept control (input) signals?

Last Answer : A bias winding and associated circuitry.

If the differential amplifier is configured with a single input and differential outputs, what will the output signals be?

Description : If the differential amplifier is configured with a single input and differential outputs, what will the output signals be?

Last Answer : Each output will be a sine wave with a peak-to-peak amplitude of 100 millivolts. The output signals will be 180 degrees out of phase with each other.

What two transistor amplifier configurations are combined in the single-transistor, two-input, single-output difference amplifier?

Description : What two transistor amplifier configurations are combined in the single-transistor, two-input, single-output difference amplifier?

Last Answer : Common emitter (CE) and common base (CB)

In a nondegenerative parametric amplifier the difference between the input frequency and the pump frequency is called what?

Description : In a nondegenerative parametric amplifier the difference between the input frequency and the pump frequency is called what?

Last Answer : Idler- or lower-sideband frequency.

If the rf amplifier discussed has an 80 milliwatt input, what would be the maximum output?

Description : If the rf amplifier discussed has an 80 milliwatt input, what would be the maximum output?

Last Answer : 800 watts.

In the power amplifier shown in figure 2-10, what two signals are mixed to produce the output signal? In the power amplifier shown in figure 2-10, what two signals are mixed to produce the output signal?

Description : In the power amplifier shown in figure 2-10, what two signals are mixed to produce the output signal?

Last Answer : Local oscillator and coherent oscillator.

What is the primary difference between the pump signal of a simple parametric amplifier and the pump signal of a nondegenerative parametric amplifier?

Description : What is the primary difference between the pump signal of a simple parametric amplifier and the pump signal of a nondegenerative parametric amplifier?

Last Answer : The pump signal of a nondegenerative parametric amplifier is higher than twice the input signal.

What type of amplifier would be used to amplify the signal from a radio antenna?

Description : What type of amplifier would be used to amplify the signal from a radio antenna?

Last Answer : An rf voltage amplifier.

An operational amplifier, as used in today's consoles, has a calculated gain of 5. This means that when the input changes _____________. A. 5 volts, the output changes 10 volts B. 10 volts, the output changes 5 volts C. 2 volts, the output changes 10 volts D. 10 volts, the output changes 2 volts

Description : An operational amplifier, as used in today's consoles, has a calculated gain of 5. This means that when the input changes _____________. A. 5 volts, the output changes 10 volts B. 10 volts, the output changes 5 volts C. 2 volts, the output changes 10 volts D. 10 volts, the output changes 2 volts

Last Answer : Answer: C

When troubleshooting an amplifier, you measure an output of 30 volts. If the gain of the amplifier is 2, what must the input voltage be for the amplifier to work properly? A. 32 volts B. 30 volts C. 28 volts D. 15 volts

Description : When troubleshooting an amplifier, you measure an output of 30 volts. If the gain of the amplifier is 2, what must the input voltage be for the amplifier to work properly? A. 32 volts B. 30 volts C. 28 volts D. 15 volts

Last Answer : Answer: D

An operational amplifier, as used in today's consoles, may have a calculated gain of 5. This means that as the input changes by ______________. A. 1 volt, the output changes 5 volts B. 5 volts, the output changes 1 volt C. 5 volts, the output changes 10 volts D. 10 volts, the output changes 5 volts

Description : An operational amplifier, as used in today's consoles, may have a calculated gain of 5. This means that as the input changes by ______________. A. 1 volt, the output changes 5 volts B. 5 volts, the output changes 1 volt C. 5 volts, the output changes 10 volts D. 10 volts, the output changes 5 volts

Last Answer : Answer: A

Basic operating characteristics of the operational amplifier such as gain and stability are the function of its _____________. A. differential input stage B. power output stage C. feedback circuit D. supply voltages

Description : Basic operating characteristics of the operational amplifier such as gain and stability are the function of its _____________. A. differential input stage B. power output stage C. feedback circuit D. supply voltages

Last Answer : Answer: C

The first stage of a two-stage amplifier has a voltage gain of 10, a 600 Ω input resistor, a 1600Ω equivalent noise resistance and 27kΩ output resistor. For the second stage, these values are 25, 81kΩ, 19kΩ, and 1MΩ, respectively. Calculate the equivalent input-noise resistance of this two stage amplifier. A. 2,518 kΩ B. 2,518 Ω C. 251.8 Ω D. 12,518 Ω

Description : The first stage of a two-stage amplifier has a voltage gain of 10, a 600 Ω input resistor, a 1600Ω equivalent noise resistance and 27kΩ output resistor. For the second stage, these values are 25, 81kΩ, 19kΩ, and 1MΩ, ... this two stage amplifier. A. 2,518 kΩ B. 2,518 Ω C. 251.8 Ω D. 12,518 Ω

Last Answer : B. 2,518 Ω

An amplifier without feedback has a voltage gain of 50, input resistance 1kΩ and output resistance of 2.5kΩ.

Description : An amplifier without feedback has a voltage gain of 50, input resistance 1kΩ and output resistance of 2.5kΩ. The input resistance of the current-shunt negative feedback amplifier using the above amplifier with a feedback factor of 0.2 would be: (1) 1/11 kΩ (2) 1/5 kΩ (3) 5 kΩ (4) 11 kΩ

Last Answer : An amplifier without feedback has a voltage gain of 50, input resistance 1kΩ and output resistance of 2.5kΩ. The input resistance of the current-shunt negative feedback amplifier using the above amplifier with a feedback factor of 0.2 would be: 1/11 kΩ

An amplifier has input power of 2 microwatts. The power gain of the amplifier is 60 dB. The output power will be

Description : An amplifier has input power of 2 microwatts. The power gain of the amplifier is 60 dB. The output power will be

Last Answer : An amplifier has input power of 2 microwatts. The power gain of the amplifier is 60 dB. The output power will be 2 watts

What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna compared to the output power of the transmitter C. The ratio of the signal in the backward direction D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Description : What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna ... D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Last Answer : D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or load resistor B. noise factor expressed in decibels C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signal D. S/N of an ideal system divided by S/N at the output of the receiver or amplifier under test, both working at the same temperature over the same bandwidth and fed from the same source

Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source

Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals

If the operating point of an NPN transistor amplifier is selected in saturation region, it is likely to result in A) Thermal runaway of transistor B) Clipping of output in the positive half of the input signal C) Need for high dc collector supply D) Clipping of output in the negative half of the input signal

Description : If the operating point of an NPN transistor amplifier is selected in saturation region, it is likely to result in A) Thermal runaway of transistor B) Clipping of output in the positive half of the ... for high dc collector supply D) Clipping of output in the negative half of the input signal

Last Answer : B) Clipping of output in the positive half of the input signal

Which of the following is not true: A) An oscillator is a circuit that converts DC to AC B) An oscillator is an amplifier that supplies its own input signal C) All oscillators generate sine waves D) In phase feedback is called positive Feedback

Description : Which of the following is not true: A) An oscillator is a circuit that converts DC to AC B) An oscillator is an amplifier that supplies its own input signal C) All oscillators generate sine waves D) In phase feedback is called positive Feedback

Last Answer : C) All oscillators generate sine waves

The circuit which changes input signal at output with phase shift of 1800 is called (a) Amplifier (b) operational amplifier (c) switch (d) inverter

Description : The circuit which changes input signal at output with phase shift of 1800 is called (a) Amplifier (b) operational amplifier (c) switch (d) inverter

Last Answer : (d) inverter

Negative feedback amplifier has a signal corrupted by noise as its input. The amplifier will

Description : Negative feedback amplifier has a signal corrupted by noise as its input. The amplifier will   (A) Amplify the noise as much as the signal (B) Reduce the noise (C) Increase the noise (D) Not effect the noise

Last Answer : Negative feedback amplifier has a signal corrupted by noise as its input. The amplifier will Reduce the noise

In the illustrated amplifier, the RESET potentiometer A1R2 sets the stability of the control loop by changing the reset time constant. As the potentiometer is turned clockwise _________. EL-0060 A. the gain is increased B. the stability is increased by slowing the response time C. feedback is increased to the summing point at terminal 5 D. response time is increased decreasing stability

Description : In the illustrated amplifier, the RESET potentiometer A1R2 sets the stability of the control loop by changing the reset time constant. As the potentiometer is turned clockwise _________. EL-0060 A. ... is increased to the summing point at terminal 5 D. response time is increased decreasing stability

Last Answer : Answer: B