Description : If the two input signals to a difference amplifier are equal in amplitude but neither in phase nor 180 degrees out of phase, what will the output signal be?
Last Answer : . A different shape than the input signals but larger in amplitude.
Description : If the two input signals to a difference amplifier are equal in amplitude and 180 degrees out of phase, what will the output signal be?
Last Answer : Equal in shape and frequency to each input signal and larger in amplitude by two times than
Description : If If the input signals are 180 degrees out of phase with each other and a combined output is taken between the two output terminals, what will the amplitude of the combined output signal be?
Last Answer : 200 millivolts.
Description : If the single-input, differential-output, differential amplifier has an output signal taken between the two output terminals, what will the peak-to-peak amplitude of this combined output be?
Last Answer : 200 millivolts. A-18. a. Differential amplifier
Description : If the input signals are 180 degrees out of phase with each other, what will be the peak-to-peak amplitude of the output signals?
Last Answer : Each output signal will be 100 millivolts.
Description : If the input signals are in phase, what will be the peak-to peak amplitude of the output signals?
Last Answer : 0 volts (the input signals will "cancel out").
Description : The input and output signals of a JFET amplifier have what phase relationship?
Last Answer : They are 180 degrees out of phase.
Description : If only one input signal is used with a difference amplifier, what will the output signal be?
Last Answer : Equal in shape and frequency to the input signal; larger in amplitude than the input signal; half as large in amplitude as when two input signals were used that were 180 degrees out of phase.
Description : In the basic transistor amplifier discussed earlier, what is the relationship between the polarity of the input and output signals?
Last Answer : The signals are opposite in polarity or 180 degrees out of phase with each other.
Description : If the differential amplifier is configured with a single input and differential outputs, what will the output signals be?
Last Answer : Each output will be a sine wave with a peak-to-peak amplitude of 100 millivolts. The output signals will be 180 degrees out of phase with each other.
Description : In the power amplifier shown in figure 2-10, what two signals are mixed to produce the output signal?
Last Answer : Local oscillator and coherent oscillator.
Description : Which transistor configuration provides a phase reversal between the input and output signals?
Last Answer : Common emitter.
Description : The circuit which changes input signal at output with phase shift of 1800 is called (a) Amplifier (b) operational amplifier (c) switch (d) inverter
Last Answer : (d) inverter
Description : The voltage at the reference electrode of the circuit shown in the illustration is applied to the input of a/an ______________. EL-0090 A. class A detector whose output drives an ... drives an 2-stage isolation transformer D. magnetic amplifier whose output controls a saturable reactor
Last Answer : Answer: D
Description : What is used to bias a magnetic amplifier so that the control winding remains free to accept control (input) signals?
Last Answer : A bias winding and associated circuitry.
Description : What two transistor amplifier configurations are combined in the single-transistor, two-input, single-output difference amplifier?
Last Answer : Common emitter (CE) and common base (CB)
Description : If the inductance of a choke-input filter is increased, will the output ripple voltage amplitude (Er) increase or decrease?
Last Answer : Decrease.
Description : What components form the input-signal-developing impedance for the amplifier?
Last Answer : C2 and the secondary of T1.
Description : If the input-signal-developing impedance of an amplifier is increased, what is the effect on the gain?
Last Answer : The gain increases.
Description : In the inverting configuration, what is the voltage (for all practical purposes) at the inverting input to the operational amplifier if the input signal is a 1-volt, peak-to-peak sine wave?
Last Answer : 0 volts.
Description : The pump signal frequency must be of what value when compared to the input signal of a simple parametric amplifier?
Last Answer : Exactly double the input frequency.
Description : Does an amplifier actually change an input signal? Why or why not?
Last Answer : No, the input signal is unchanged, the output signal is controlled by the input signal but does not effect the actual input signal.
Description : The term responsivity as it applies to a light detector is best described as ∙ A. the time required for the signal to go from 10 to 90 percent of maximum amplitude ∙ B. the ratio of the diode ... . the ratio of the input power to output power ∙ D. the ratio of output current to input current
Last Answer : the ratio of the diode output current to the input optical power
Description : The termresponsivityasit appliesto a light detectorisbest described as a. the time required for the signal to go from 10 to 90 percent of maximum amplitude b.the ratio ofthediode output currentto ... of output current to output power d. the ratio of output current to input current
Last Answer : b.the ratio ofthediode output currentto opticalinputpower
Description : Two tape recorders have signal-to-noise ratios (SNRs) of 25-dB RMS and 35-dB RMS respectively. Which of the SNRs can record and reproduce the widest range of input signals and why?
Last Answer : 35-dB RMS because the highest SNR can always record and reproduce the widest range of input signals.
Description : If the rf amplifier discussed has an 80 milliwatt input, what would be the maximum output?
Last Answer : 800 watts.
Description : In inverting amplifier, the phase difference between input and output voltages must be A. 30° B. 45° C. 90° D. 180°
Last Answer : 180°
Description : For non-inverting amplifier the input and output is A. out of phase B. in phase C. have phase difference of 180° D. have phase difference of 90°
Last Answer : in phase
Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source
Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals
Description : If the operating point of an NPN transistor amplifier is selected in saturation region, it is likely to result in A) Thermal runaway of transistor B) Clipping of output in the positive half of the ... for high dc collector supply D) Clipping of output in the negative half of the input signal
Last Answer : B) Clipping of output in the positive half of the input signal
Description : Which set of truth table input signals will result in an output signal value of 1 from the 'AND' gate as shown in the illustration? EL-0035 A. 1-Jan B. Jan-00 C. 0-1 D. 0-0
Last Answer : Answer: A
Description : As shown in the illustration, which set of truth table input signals will result in an output signal at point 'Y'? EL-0035 A. 0-0 B. 0-1 C. Jan-00 D. 1-Jan
Description : One of the FM signal generator control which varies the phase of the modulating voltage applied to the oscillator of the sweep generator A. Band control B. Phase control C. Marker amplitude control D. Sweep output control
Last Answer : B. Phase control
Description : Amplitude of modulated wave is in phase with A. output B. system C. frequency D. signal
Last Answer : signal
Description : Which of the following is not true: A) An oscillator is a circuit that converts DC to AC B) An oscillator is an amplifier that supplies its own input signal C) All oscillators generate sine waves D) In phase feedback is called positive Feedback
Last Answer : C) All oscillators generate sine waves
Description : In the illustrated circuit, what is the phase relationship of the amplifier output compared to the input? EL-0022 A. 0° in-phase B. 180° out of phase C. phase angle of the input divided by power factor D. unable to determine without the value of the bias voltage
Last Answer : Answer: B
Description : In a circuit such as that shown in figure 3-16, if R1 has a value of 50 ohms and R2 has a value of 250 ohms and the input signal has a value of +10 millivolts, what is the value of the output signal?
Last Answer : 60 millivolts.
Description : In a circuit such as that shown in figure 3-15, if R1 has a value of 100 ohms and R2 has a value of 1 kilohm and the input signal is at a value of + 5 millivolts, what is the value of the output signal?
Last Answer : 50 millivolts.
Description : select the correct response from the choices given in the parentheses. Q-20. In a closed-loop configuration the output signal is determined by (the input signal, the feedback signal, both).
Last Answer : Both the input signal and the feedback signal.
Description : How does dc bias added to the input signal correct the distortion in the output signal?
Last Answer : The dc bias moves the input signal away from the step in the magnetism curve. This prevents the input signal from crossing the zero-point of the magnetism curve.
Description : If the output of a circuit needs to be a complete representation of one-half of the input signal, what class of operation is indicated?
Last Answer : Class B operation.
Description : If the percentage modulation of an AM amplifier is 88% and the modulating signal is 1 volt, the carrier has an amplitude of _______________. A. 1.14 volts B. 0.88 volt C. 1.88 volts D. 0.12 volt
Last Answer : A. 1.14 volts
Description : In a nondegenerative parametric amplifier the difference between the input frequency and the pump frequency is called what?
Last Answer : Idler- or lower-sideband frequency.
Description : What is the primary difference between the pump signal of a simple parametric amplifier and the pump signal of a nondegenerative parametric amplifier?
Last Answer : The pump signal of a nondegenerative parametric amplifier is higher than twice the input signal.
Description : The absolute value of a signal's highest intensity is called………. A. Peak Amplitude B. Frequency C. Phase D. Both a and c
Last Answer : A. Peak Amplitude
Description : On oscilloscope screen for dynamic measurement, lissajous diagram is normally used to determine the __________ of the input signal. (A) Frequency (B) Amplitude (C) Damping (D) None of these
Last Answer : (A) Frequency
Description : When a large signal and a small signal are applied to a lin log amplifier at the same time, what is the effect on the small signal?
Last Answer : Amplification is reduced.
Description : What type of amplifier would be used to amplify the signal from a radio antenna?
Last Answer : An rf voltage amplifier.
Description : Negative feedback amplifier has a signal corrupted by noise as its input. The amplifier will (A) Amplify the noise as much as the signal (B) Reduce the noise (C) Increase the noise (D) Not effect the noise
Last Answer : Negative feedback amplifier has a signal corrupted by noise as its input. The amplifier will Reduce the noise
Description : If C4 were removed from the circuit, what would happen to the output of the amplifier?
Last Answer : The output would decrease. (C4 decouples R2 preventing degenerative feedback from R2.)