Convert 350 mA to amperes.

Convert 350 mA to amperes.
by

1 Answer

Answer :

0.35 amperes.
by

Related questions

What is the power used in a circuit that has 10 amperes of current through a 10-ohm resistor?

Description : What is the power used in a circuit that has 10 amperes of current through a 10-ohm resistor?

Last Answer : 1 kilowatt.

If Eeff is 130 volts and Ieff is 3 amperes, what is the total resistance (RT) in the circuit?

Description : If Eeff is 130 volts and Ieff is 3 amperes, what is the total resistance (RT) in the circuit?

Last Answer : 43.3 ohms.

A galvanometer of 65 Ω resistance gives full scale deflection with 4 mA current. In order to convert it into ammeter, the range of 10 A is connected with it, the shunt resistance should be a) 0.1 Ω b) 0.2 Ω c) 0.06 Ω d) 0.03 Ω

Description : A galvanometer of 65 Ω resistance gives full scale deflection with 4 mA current. In order to convert it into ammeter, the range of 10 A is connected with it, the shunt resistance should be a) 0.1 Ω b) 0.2 Ω c) 0.06 Ω d) 0.03 Ω

Last Answer : d) 0.03 Ω

If a voltage divider is required for a load that will use 450 mA of current, what should be the value of bleeder current?

Description : If a voltage divider is required for a load that will use 450 mA of current, what should be the value of bleeder current?

Last Answer : 45 mA rule-of-thumb.

Convert 2.1 kV to volts.

Description : Convert 2.1 kV to volts.

Last Answer : 2100 volts.

What component is used in a triode amplifier to convert variation in

Description : What component is used in a triode amplifier to convert variation in

Last Answer : A plate load resistor RL

Generators convert mechanical motion to electrical energy using what principle?

Description : Generators convert mechanical motion to electrical energy using what principle?

Last Answer : Magnetic induction

Ships’ generators produce 450-volt, three-phase, ac power; however, most equipment uses 117-volt, single-phase power What transformers and connections are used to convert 450- volt, threephase power to 117-volt, single-phase power?

Description : Ships’ generators produce 450-volt, three-phase, ac power; however, most equipment uses 117-volt, single-phase power What transformers and connections are used to convert 450- volt, threephase power to 117-volt, single-phase power?

Last Answer : A method of generating oscillations, a method of turning the oscillations on and off (keying), and an antenna to radiate the energy.

What is Ampere's Law ?

Description : What is Ampere's Law ?

Last Answer : : The French mathematician Adrienne Marie discovered the law of the ball between two conductors carrying an ampere current. This formula is named after him. The force acting between two current-carrying parallel conductors is ... or , F = 2X10-7I1I2L / r Here , 2X10-7 = proportional constant

Nichrome wire is used in an electric heater because _______. (1) It has high resistance (2) It has high melting point (3) It can resist a current upto approx 5 amperes (4) For all of the above reasons

Description : Nichrome wire is used in an electric heater because _______. (1) It has high resistance (2) It has high melting point (3) It can resist a current upto approx 5 amperes (4) For all of the above reasons

Last Answer : (4) For all of the above reasons

What is the SI unit of electric current? (1) Amperes (2) Coulombs (3) Joules (4) Watts

Description : What is the SI unit of electric current? (1) Amperes (2) Coulombs (3) Joules (4) Watts

Last Answer : (1) Amperes Explanation: The SI unit for measuring an electric current is the am pere, which is the flow of electric charge across a surface at the rate of one coulomb per second.

Which of the following precautions should be taken when a blown fuse, rated at 10 amperes, is replaced? A. Short out the fuse before removing it from the circuit. B. Use needle-nose pliers to remove fuse from the circuit. C. Replace blown fuse with one of equal voltage and ampere capacity. D. Fuses of 10 ampere rating and less are virtually harmless when energized and may be handled freely.

Description : Which of the following precautions should be taken when a blown fuse, rated at 10 amperes, is replaced? A. Short out the fuse before removing it from the circuit. B. Use needle-nose pliers to ... D. Fuses of 10 ampere rating and less are virtually harmless when energized and may be handled freely.

Last Answer : Answer: C

As shown in the illustration, the function of the switch labeled 'PFSW' is to determine the ______________. EL-0003 A. bus frequency B. reactive volt amperes of the bus C. frequency of either generator D. power factor of either generator

Description : As shown in the illustration, the function of the switch labeled 'PFSW' is to determine the ______________. EL-0003 A. bus frequency B. reactive volt amperes of the bus C. frequency of either generator D. power factor of either generator

Last Answer : Answer: D

How many volts are necessary to provide a current of 10 amperes to a motor with an in-line resistance of 11 ohms? A. 21 volts B. 110 volts C. 220 volts D. 240 volts

Description : How many volts are necessary to provide a current of 10 amperes to a motor with an in-line resistance of 11 ohms? A. 21 volts B. 110 volts C. 220 volts D. 240 volts

Last Answer : Answer: B

What power is consumed by a heating element using a current of 20 amperes at 120 volts? A. 20 watts B. 66.67 watts C. 720 watts D. 2400 watts

Description : What power is consumed by a heating element using a current of 20 amperes at 120 volts? A. 20 watts B. 66.67 watts C. 720 watts D. 2400 watts

Last Answer : Answer: D

What is the wattage of a heating element drawing a current of 30 amperes, at 120 volts? A. 30 watts B. 99.97 watts C. 360 watts D. 3600 watts

Description : What is the wattage of a heating element drawing a current of 30 amperes, at 120 volts? A. 30 watts B. 99.97 watts C. 360 watts D. 3600 watts

Last Answer : Answer: D

Two 100 watt light bulbs are connected in parallel across a 100 volt power supply. The total power developed in the circuit is _______________. A. 200 watts B. 100 watts C. 50 watts D. equal to the product of the amperes times the voltage in each branch

Description : Two 100 watt light bulbs are connected in parallel across a 100 volt power supply. The total power developed in the circuit is _______________. A. 200 watts B. 100 watts C. 50 watts D. equal to the product of the amperes times the voltage in each branch

Last Answer : Answer: A

A lead-acid battery can deliver 20 amperes continuously for 10 hours with an ampere-hour rating of ____________. A. 20 B. 40 C. 200 D. 400

Description : A lead-acid battery can deliver 20 amperes continuously for 10 hours with an ampere-hour rating of ____________. A. 20 B. 40 C. 200 D. 400

Last Answer : Answer: C

A circuit breaker for a 300 KW alternator is rated at 470 amperes of full continuous load. The amount of overcurrent allowed is 125%. Which of the following conditions will trip the breaker? A. Sustained current flow of 470 amperes. B. Sustained current flow of 500 amperes for 10 minutes. C. Momentary starting load of 550 amperes. D. Sustained current flow of 590 amperes.

Description : A circuit breaker for a 300 KW alternator is rated at 470 amperes of full continuous load. The amount of overcurrent allowed is 125%. Which of the following conditions will trip the breaker? A. ... 10 minutes. C. Momentary starting load of 550 amperes. D. Sustained current flow of 590 amperes.

Last Answer : Answer: D

A three-phase alternator operates at 450 volts with a power factor of 0.8. If the ammeter indicates 250 amperes, what should be the KW meter reading? A. 90.00 KW B. 127.27 KW C. 155.70 KW D. 194.85 KW

Description : A three-phase alternator operates at 450 volts with a power factor of 0.8. If the ammeter indicates 250 amperes, what should be the KW meter reading? A. 90.00 KW B. 127.27 KW C. 155.70 KW D. 194.85 KW

Last Answer : Answer: C

An electrical component is connected across a 120 volt 60 hertz AC supply. What is the current drawn by the component if the impedance is 200 ohms? A. 0.01 amperes B. 0.60 amperes C. 1.67 amperes D. 100 amperes

Description : An electrical component is connected across a 120 volt 60 hertz AC supply. What is the current drawn by the component if the impedance is 200 ohms? A. 0.01 amperes B. 0.60 amperes C. 1.67 amperes D. 100 amperes

Last Answer : Answer: B

The distance between a generator and its load is 100 feet. What would be the approximate total voltage drop across a two wire supply cable if the current were 5.5 amperes and the resistance of the wire were 2.525 ohms per 1,000 feet? A. 0.5 volts B. 1.38 volts C. 1.90 volts D. 2.77 volts

Description : The distance between a generator and its load is 100 feet. What would be the approximate total voltage drop across a two wire supply cable if the current were 5.5 amperes and the resistance of the wire were 2.525 ohms per 1,000 feet? A. 0.5 volts B. 1.38 volts C. 1.90 volts D. 2.77 volts

Last Answer : Answer: D

What current is required to light two 75 watt lamps and one 40 watt lamp when connected in series to a 120 volt power source? A. 0.161 amperes B. 0.631 amperes C. 1.583 amperes D. 6.199 amperes

Description : What current is required to light two 75 watt lamps and one 40 watt lamp when connected in series to a 120 volt power source? A. 0.161 amperes B. 0.631 amperes C. 1.583 amperes D. 6.199 amperes

Last Answer : Answer: C

Battery capacities are given in _____________. A. volts B. volt-amperes C. volt-hours D. ampere-hours

Description : Battery capacities are given in _____________. A. volts B. volt-amperes C. volt-hours D. ampere-hours

Last Answer : Answer: D

Electric current is the flow of electrons through a conductor; the rate of this flow is measured in ___________. A. volts B. amperes C. coulombs D. ohms

Description : Electric current is the flow of electrons through a conductor; the rate of this flow is measured in ___________. A. volts B. amperes C. coulombs D. ohms

Last Answer : Answer: B

The inductance of a coil is measured in _____________. A. ohms B. volts C. henries D. amperes

Description : The inductance of a coil is measured in _____________. A. ohms B. volts C. henries D. amperes

Last Answer : Answer: C

Which of the following statements regarding the use of a current measuring instrument is correct? A. It must be connected in series with the circuit. B. You should always start with the lowest range until a suitable reading is obtained. C. The indicating needle is deflected from left to right regardless of polarity. D. An external shunt is generally utilized where current is less than 10 amperes.

Description : Which of the following statements regarding the use of a current measuring instrument is correct? A. It must be connected in series with the circuit. B. You should always start with the lowest range ... of polarity. D. An external shunt is generally utilized where current is less than 10 amperes.

Last Answer : Answer: A

Electric current is the flow of electrons through a conductor. The rate of this flow is measured as ___________. A. volts/watt B. amperes/centimetre C. coulombs/second D. ohms/volt

Description : Electric current is the flow of electrons through a conductor. The rate of this flow is measured as ___________. A. volts/watt B. amperes/centimetre C. coulombs/second D. ohms/volt

Last Answer : Answer: C

The ratio of the effective value of the counter EMF in volts, to the effective value of the current in amperes is called _____________. A. impedance factor B. capacitive reactance C. inductive reactance D. root mean square

Description : The ratio of the effective value of the counter EMF in volts, to the effective value of the current in amperes is called _____________. A. impedance factor B. capacitive reactance C. inductive reactance D. root mean square

Last Answer : Answer: C

Power transformers are rated in _____________. A. kilowatts B. ampere-turns C. kilowatt-volts D. kilovolt-amperes

Description : Power transformers are rated in _____________. A. kilowatts B. ampere-turns C. kilowatt-volts D. kilovolt-amperes

Last Answer : Answer: D

In cranking the engine normally motor takes current about a) 300 amperes b) 400 amperesb) 5 0 0 amperes d) 600 amperes

Description : In cranking the engine normally motor takes current about a) 300 amperes b) 400 amperesb) 5 0 0 amperes d) 600 amperes

Last Answer : b) 400 amperes

The change in base current will be A) 0.66 micro ampere B) 6.6 micro amperes C) 66 micro amperes D) 660 micro amperes.

Description : The change in base current will be A) 0.66 micro ampere B) 6.6 micro amperes C) 66 micro amperes D) 660 micro amperes.

Last Answer : A) 0.66 micro ampere

The Principle of an alternating current generator is based on: a. Coulomb’s law b. Ampere’s law c. Faraday’s law d. Lenz’s law

Description : The Principle of an alternating current generator is based on: a. Coulomb’s law b. Ampere’s law c. Faraday’s law d. Lenz’s law

Last Answer : a. Coulomb’s law

Alternators are preferred over dynamo because A. Alternators can produce a strong current of 30-40 amperes. B. Alternators don’t required cutout reiny C. Alternators don’t have commutaters D. All of the above

Description : Alternators are preferred over dynamo because A. Alternators can produce a strong current of 30-40 amperes. B. Alternators don’t required cutout reiny C. Alternators don’t have commutaters D. All of the above

Last Answer : D. All of the above

The transformer ratings are usually expressed in terms of A. Volts B. Amperes C. kW D. kVA

Description : The transformer ratings are usually expressed in terms of A. Volts B. Amperes C. kW D. kVA

Last Answer : D) KVA

A current of 6 amperes flows through a 2 ohm resistor for 30 seconds. How many coulombs of charge have passed through the resistor?

Description : A current of 6 amperes flows through a 2 ohm resistor for 30 seconds. How many coulombs of charge have passed through the resistor? 

Last Answer : ANSWER: 180 COULOMBS

Ten Coulombs of charge flowing through a wire per second is equal to: w) 100 Amperes x) 10 Ampere y) 1 Amperes z) 0.1 Amperes

Description : Ten Coulombs of charge flowing through a wire per second is equal to: w) 100 Amperes x) 10 Ampere y) 1 Amperes z) 0.1 Amperes

Last Answer : ANSWER: X -- 10 AMPERES

A 20 ohm resistor and a 60 ohm resistor are connected in parallel to a voltage source. If the current in the 60 ohm resistor is one ampere, the current in the 20 ohm resistor will be: w) 1/3 ampere x) 2/3 ampere y) 1 ampere z) 3 amperes

Description : A 20 ohm resistor and a 60 ohm resistor are connected in parallel to a voltage source. If the current in the 60 ohm resistor is one ampere, the current in the 20 ohm resistor will be: w) 1/3 ampere x) 2/3 ampere y) 1 ampere z) 3 amperes

Last Answer : ANSWER: Z -- 3 AMPERES

Gauss' law of electricity, Gauss' law of magnetism, Faraday's law of induction, and Amperes' law form the basic equations of electromagnetism. This combination is collectively known as: w) Coulomb's equations x) Volta's equations y) Fermi's equations z) Maxwell's equations

Description : Gauss' law of electricity, Gauss' law of magnetism, Faraday's law of induction, and Amperes' law form the basic equations of electromagnetism. This combination is collectively known as: w) Coulomb's equations x) Volta's equations y) Fermi's equations z) Maxwell's equations

Last Answer : ANSWER: Z -- MAXWELL'S EQUATIONS

The rate at which electrical energy is used is measured in w) volts x) amperes y) joules z) watts

Description : The rate at which electrical energy is used is measured in w) volts x) amperes y) joules z) watts

Last Answer : ANSWER: Z -- WATTS

Which one of the following laws best describes the operation of an electric generator? w) Ampere's Law x) Gauss' Law y) Ohm's Law for Conductors z) Faraday's Law of Induction

Description : Which one of the following laws best describes the operation of an electric generator? w) Ampere's Law x) Gauss' Law y) Ohm's Law for Conductors z) Faraday's Law of Induction

Last Answer : ANSWER: Z -- FARADAY'S LAW OF INDUCTION 

What law describes the force between two stationary electrically charged objects? w) Ampere's law x) Coulomb's law y) Kirchoff's Rules (pron: kir-koff rules) z) Ohm's law

Description : What law describes the force between two stationary electrically charged objects? w) Ampere's law x) Coulomb's law y) Kirchoff's Rules (pron: kir-koff rules) z) Ohm's law

Last Answer : ANSWER: X -- COULOMB'S LAW

Induced electric currents can be explained using which of the following laws? w) Gauss's Law x) Faraday's Law y) Ohm's Law z) Ampere's Law

Description : Induced electric currents can be explained using which of the following laws? w) Gauss's Law x) Faraday's Law y) Ohm's Law z) Ampere's Law

Last Answer : ANSWER: X -- FARADAY'S LAW

The force acting between two point charges can be computed using which of the following laws? w) Ohm's Law x) Ampere's Law y) Coulomb's Law z) Newton's Second Law.

Description : The force acting between two point charges can be computed using which of the following laws? w) Ohm's Law x) Ampere's Law y) Coulomb's Law z) Newton's Second Law.

Last Answer : ANSWER: Y -- COULOMB'S LAW

A current of 4 amperes flowing for 45 minutes deposits 1.062 gm of metal at cathode. Calculate the equivalent weight of the metal. (Given 1 Faraday = 96500 C)

Description : A current of 4 amperes flowing for 45 minutes deposits 1.062 gm of metal at cathode. Calculate the equivalent weight of the metal. (Given 1 Faraday = 96500 C)

Last Answer : Given:  c : 4 amperes   t : 45 minutes : 45 x 60 = 2700 seconds   w : 1.062 gm   1 Faraday : 96500 C  To calculate: Eq. Weight (CE)  According to Faraday's first law:   w = z c t Therefore,  z = w / ct  ... g/c   Now, C.E. = 96500 x E.C.E.   C. E. = 96500 x 0.00009833  C.E. = 9.4888 gm

What is Ampere's law equation?

Description : What is Ampere's law equation?

Last Answer : Module 3 : MAGNETIC FIELD Lecture 16 : Ampere's Law Objectives In this lecture you will learn the following Establish Ampere' law in integral form. Calculate the magnetic field for certain current ... NPTEL Distributed under Creative Commons Attribution-ShareAlike - CC BY-SA.

For a given base voltage and base volt-amperes, the per unit impedance value is x. For the doubled base

Description : For a given base voltage and base volt-amperes, the per unit impedance value is x. For the doubled base values of both voltage and volt-amperes, the per unit impedance will be (a) 2x (b) 0.25x (c) 0.5x (d) no change 

Last Answer : Answer is 2x Base impedance =(base voltage) ²/base current 

A 50 Hz, 4-pole, 500 MVA, 22 kV turbo-generator is delivering rated megavolt amperes at 0.8 power factor.

Description : A 50 Hz, 4-pole, 500 MVA, 22 kV turbo-generator is delivering rated megavolt amperes at 0.8 power factor. Suddenly a fault occurs reducing in electric power output by 40%. Neglect losses and assume constant power input to the ... the time of fault will be  (A) 1.528 (B) 1.018 (C) 0.848 (D) 0.509

Last Answer : A 50 Hz, 4-pole, 500 MVA, 22 kV turbo-generator is delivering rated megavolt amperes at 0.8 power factor. Suddenly a fault occurs reducing in electric power output by 40%. Neglect losses and assume ... the shaft. The accelerating torque in the generator in MNm at the time of fault will be 1.018 

Four amperes of current are measured through a 24 ohms resistor connected across a voltage

Description : Four amperes of current are measured through a 24 ohms resistor connected across a voltage source. How much voltage does the source produce? A.960 V B.9.6 V C.96 V D.8 V

Last Answer : Four amperes of current are measured through a 24 ohms resistor connected across a voltage source. How much voltage does the source produce? A.960 V B.9.6 V C.96 V D.8 V

The number of micro amperes in 2 milli amperes is?

Description : The number of micro amperes in 2 milli amperes is? A.2 μA B.20 μA C.200 μA D.2,000 μA

Last Answer : The number of micro amperes in 2 milli amperes is? A.2 μA B.20 μA C.200 μA D.2,000 μA