Four amperes of current are measured through a 24 ohms resistor connected across a voltage source. How much voltage does the source produce?
A.960 V
B.9.6 V
C.96 V
D.8 V
Description : When there is 12 mA of current through a 1.2 k ohms resistor, the voltage across the resistor is? A.14.4 V B.1.4 V C.100 V D.10 V
Last Answer : When there is 12 mA of current through a 1.2 k ohms resistor, the voltage across the resistor is? A.14.4 V B.1.4 V C.100 V D.10 V
Description : How much voltage is needed to produce 2.5 A of current through a 200 ohms resistor? A.50 V B.500 V C.80 V D.8 V
Last Answer : 500 V
Description : An electrical component is connected across a 120 volt 60 hertz AC supply. What is the current drawn by the component if the impedance is 200 ohms? A. 0.01 amperes B. 0.60 amperes C. 1.67 amperes D. 100 amperes
Last Answer : Answer: B
Description : What amount of current will flow through resistance of 10 ohms when it is connected across a potential difference of 20 volts? A.30 amperes B.5 amperes C.10 amperes D.2 amperes
Last Answer : 2 amperes
Description : The distance between a generator and its load is 100 feet. What would be the approximate total voltage drop across a two wire supply cable if the current were 5.5 amperes and the resistance of the wire were 2.525 ohms per 1,000 feet? A. 0.5 volts B. 1.38 volts C. 1.90 volts D. 2.77 volts
Last Answer : Answer: D
Description : Twelve volts are applied across a resistor. A current of 3 mA is measured. What is the value of the resistor? A.4 ohms B.400 ohms C.4 kohms D.4.4 ohms
Last Answer : Twelve volts are applied across a resistor. A current of 3 mA is measured. What is the value of the resistor? A.4 ohms B.400 ohms C.4 kohms D.4.4 ohms
Description : A 20 ohm resistor and a 60 ohm resistor are connected in parallel to a voltage source. If the current in the 60 ohm resistor is one ampere, the current in the 20 ohm resistor will be: w) 1/3 ampere x) 2/3 ampere y) 1 ampere z) 3 amperes
Last Answer : ANSWER: Z -- 3 AMPERES
Description : A resistance of 3.3 M ohms is connected across a 500 V source. The resulting current is approximately? A.15.1 μA B.151 μA C.66 mA D.660 mA
Last Answer : A
Description : Electric current is the flow of electrons through a conductor; the rate of this flow is measured in ___________. A. volts B. amperes C. coulombs D. ohms
Description : Electric current is the flow of electrons through a conductor. The rate of this flow is measured as ___________. A. volts/watt B. amperes/centimetre C. coulombs/second D. ohms/volt
Last Answer : Answer: C
Last Answer : Req= (1/1200 +1/560 + 1/2.1)^-1 = 2.1 ohms RT= 2.1 + 7.8 = 9.9 ohms IT = V/R = 24/9.9 = 2.4 A Veq= R I = 2.1 2 ... 7.8 = 12.096 w = 44.928 w _________________________________________ By: Ellis-Junior Kamatjipose [email protected]
Description : Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor and 4.2 V rms across the other, the peak source voltage is? A.16.54 V B.1.65 V C.10.60 V D.5.93 V
Last Answer : Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor and 4.2 V rms across the other, the peak source voltage is? A.16.54 V B.1.65 V C.10.60 V D.5.93 V
Description : In the illustrated circuit, what is the voltage measured across R1 if the battery is 24 volts, the resistance of R1 is 34 ohms, and the resistance of R2 is 126 ohms? EL-0036 A. 24 volts B. 18.9 volts C. 5.1 volts D. 150 millivolts
Description : An ammeter has a full-scale deflection current of 100mA. If the same ammeter is used to measure a full-scale current of 1.0ampere, what is the value of the shunt resistor in ohms if the voltage across the meter is 9.0 volts?
Last Answer : 10 ohms
Description : An LED is operated on a 12 volt automobile circuit. The voltage drop across the LED is 2 volts and the current must be limited to 50 milliamps to prevent its overheating and destruction. What size resistor must be used? w) 60 ohms x) 100 ohms y) 120 ohms z) 200 ohms
Last Answer : ANSWER: Z -- 200 OHMS
Description : A transformer has a turns ratio of two to one. If a 100 ohm resistor is connected on the high side, its resistance as measured on the low side would be: w) 25 ohms x) 50 ohms y) 100 ohms z) 400 ohms
Last Answer : ANSWER: W -- 25 OHMS
Description : Two 100 watt light bulbs are connected in parallel across a 100 volt power supply. The total power developed in the circuit is _______________. A. 200 watts B. 100 watts C. 50 watts D. equal to the product of the amperes times the voltage in each branch
Last Answer : Answer: A
Description : The inductance of a coil is measured in _____________. A. ohms B. volts C. henries D. amperes
Description : What would be the voltage drop across the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts
Description : A resistor of value R/2 is connected in parallel with a resistor of value R/3. The voltage drop across the parallel combination is V. The total current supplied by the voltage source is: w) 2 V/R (read: 2 V over R) x) 3 V/R (read: 3 V over R) y) 4 V/R (read: 4 V over R) z) 5 V/R (read: 5 V over R)
Last Answer : ANSWER: Z -- 5 V/R
Description : A load with an impedance of 440 ohms is connected across the secondary of the transformer illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given
Description : A load with an impedance of 440 ohms is connected across the secondary of the device illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given
Description : What is the power used in a circuit that has 10 amperes of current through a 10-ohm resistor?
Last Answer : 1 kilowatt.
Description : A current of 6 amperes flows through a 2 ohm resistor for 30 seconds. How many coulombs of charge have passed through the resistor?
Last Answer : ANSWER: 180 COULOMBS
Description : A battery is connected to a circuit containing three resistors in parallel. The values of the three resistors are 2 ohms, 3 ohms, and 6 ohms. What is the voltage of the battery if the total circuit current is 12 amps? A. 2 volts B. 6 volts C. 12 volts D. 24 volt
Description : Four equal resistors are connected in parallel, each resistor has an ohmic value of 100 ohms, what is the equivalent resistance?
Last Answer : 25 ohms
Description : If an incandescent lamp of 80 ohms resistance takes a current of 0.75 ampere, what voltage is required to light it? A.45 volts B.60 volts c.23 volts D.None of these
Last Answer : V=IR = 80*0.75 = 60 volts
Description : Two resistances Rl and Ri are connected in series across the voltage source where Rl>Ri. The largest drop will be across?
Last Answer : Two resistances Rl and Ri are connected in series across the voltage source where Rl>Ri. The largest drop will be across Rl.
Description : When the pointer of an analog ohmmeter reads close to zero, the resistor being measured is? A.overheated B.shorted C.open D.reversed
Last Answer : When the pointer of an analog ohmmeter reads close to zero, the resistor being measured is? A.overheated B.shorted C.open D.reversed
Description : What voltage would be measured across the 45 ohm resistor?
Last Answer : Not enough information. But if you know the current, you can useOhm's Law (just multiply the resistance times the current).
Description : Indicate the false statement A. The noise generated in a resistance or the resistive component of any impedance is random. B. Random noise power is proportional to the bandwidth over which is measured ... exist D. All formula referring to random noise are applicable only to the value of such noise.
Last Answer : C. A random voltage across the resistor does not exist
Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 110 ohms, and R2 is 10 kohms what is the voltage measured across R1 EL-0036 A. 11.86 volts B. .131 volts C. 12 volts D. .673 volts
Description : When troubleshooting most electronic circuits, 'loading effect' can be minimized by using a voltmeter with a/an ___________________. A. input impedance much greater than the impedance across which the voltage ... sensitivity of less than 1000 ohms/volt D. sensitivity of more than 1000 volts/ohm
Description : If three wires of 3 ohms, 9 ohms and 5 ohms respectively are connected in series, what their resultant resistance? A.10 ohms B.12 ohms C.17 ohms D.5 ohms
Last Answer : If three wires of 3 ohms, 9 ohms and 5 ohms respectively are connected in series, what their resultant resistance? A.10 ohms B.12 ohms C.17 ohms D.5 ohms
Description : A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?
Last Answer : (a) 330 volts. (b) E1 = 150 volts. E2 = 180 volts. (c) 1.98 kilowatts. (d) P1 = 900 watts. P2 = 1.08 kilowatts component but in a parallel circuit total current divides among the available paths.
Description : The voltage induced across a certain coil is 200 mV. A 1200 resistor is connected to the coil terminals. The induced current will be: A. 1.7 mA B. 16 mA C. 12 mA D. 120 mA
Last Answer : The voltage induced across a certain coil is 200 mV. A 1200 resistor is connected to the coil terminals. The induced current will be: 1.7 mA
Description : How many volts are necessary to provide a current of 10 amperes to a motor with an in-line resistance of 11 ohms? A. 21 volts B. 110 volts C. 220 volts D. 240 volts
Description : A 24 volt battery supplies three devices wired in parallel that each have a resistance of 9 ohms. What is the voltage drop across each device?
Last Answer : A simple circuit has three resistors connected in series. The resistors are 14 ohms 12 ohms and 9 ohms. What is the total resistance of the circuit?
Description : What is the voltage across 'R3' of the illustrated circuit if the supply is 24 volts and the resistance of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms? EL-0020 A. 2 volts B. 6 volts C. 8 volts D. 10 volts
Description : What is the voltage across 'R2' of the illustrated circuit if the supply is 24 volts and the resistance of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms? EL-0020 A. 2 volts B. 6 volts C. 8 volts D. 10 volts
Description : What is the voltage across 'R1' of the illustrated circuit if the supply is 24 volts and resistance of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms? EL-0020 A. 2 volts B. 6 volts C. 8 volts D. 10 volts
Description : If current of 20 mA is passing through op-amp and voltage drop across series resistor is 10 V then value of resistance is A. 500Ω B. 400Ω C. 300Ω D. 200Ω
Last Answer : 500Ω
Description : If the rms voltage drop across a 15 kilt resistor is 16 V, the peak current through the resistor is : - a) 15 mA b) 1.5 mA c) 10 mA d) 1 mA
Last Answer : If the rms voltage drop across a 15 kilt resistor is 16 V, the peak current through the resistor is : - 1.5 mA
Description : In the illustrated circuit, what is the resistance across R2 if the battery voltage is 32 VDC, the resistance of R1 is 1.2 kohms and the current through R2 is 18.82 milliamps? EL-0036 A. 500 ohms B. 1,200 ohms C. 10 ohms D. The answer can not be found with the information given.
Description : The number of micro amperes in 2 milli amperes is? A.2 μA B.20 μA C.200 μA D.2,000 μA
Last Answer : The number of micro amperes in 2 milli amperes is? A.2 μA B.20 μA C.200 μA D.2,000 μA
Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 24 kohms, and R2 is 3610 ohms what is the current flowing through R1? EL-0036 A. .434 milliamps B. .005 amp C. 6.00 amps D. 2.4 milliamps
Description : When 2,4 and 6 ohms resistor are connected in parallel their resultant equivalent resistance will be A. 12ohm b. 11/12ohm C. 12/11ohm d. None
Last Answer : C. 12/11ohm
Description : A string of five resistors connected in series is connected across a 6 V battery. Zero voltage is measured across all the resistors except the third resistor. The voltage across the third resistor is: A. 0 V B. 1.2V C. 6V D. 0.6V
Last Answer : A string of five resistors connected in series is connected across a 6 V battery. Zero voltage is measured across all the resistors except the third resistor. The voltage across the third resistor is: 6V
Description : 24 cells of emf `1.5 V` each having internal resistance of 1 ohm are connected to an external resistance of `1.5` ohms. To get maximum current,
Last Answer : 24 cells of emf `1.5 V` each having internal resistance of 1 ohm are connected to an external ... in series and 4 such rows are connected in parallel
Description : A circuit is to be designed in which a capacitor must charge to 40 percent of the maximum charging voltage in 200 microseconds. The resistor to be used has a resistance of 40,000 ohms. What size capacitor must be used?
Last Answer : 0.1 microfarads 40% from the graph = 0.5