On what range should you set the voltmeter prior to taking a voltage measurement?

On what range should you set the voltmeter prior to taking  a voltage measurement?
by

1 Answer

Answer :

Highest.
by

Related questions

When taking a voltage measurement, which lead of the voltmeter should you connect to the circuit first?

Description : When taking a voltage measurement, which lead of the voltmeter should you connect to the circuit first?

Last Answer : Ground.

In order to increase its range of measurement, a resistance would be placed in series with which of the following instruments? A. DC voltmeter B. DC ammeter C. frequency meter D. power factor meter

Description : In order to increase its range of measurement, a resistance would be placed in series with which of the following instruments? A. DC voltmeter B. DC ammeter C. frequency meter D. power factor meter

Last Answer : Answer: A

Why should you always use the highest range when connecting a voltmeter to a circuit?

Description : Why should you always use the highest range when connecting a voltmeter to a circuit?

Last Answer : To prevent excess current through the meter movement.

Voltage measurement in a high impedance circuit requires a voltmeter with

Description : Voltage measurement in a high impedance circuit requires a voltmeter with

Last Answer : high input impedance

If an ac voltmeter is connected between the S2 and S3 windings on a TX, at what two rotor positions should the voltmeter read maximum voltage?

Description : If an ac voltmeter is connected between the S2 and S3 windings on a TX, at what two rotor positions should the voltmeter read maximum voltage?

Last Answer : . 150º and 330º

When making voltage measurements in a high-resistance circuit, you should always use a voltmeter with what relative value of resistance?

Description : When making voltage measurements in a high-resistance circuit, you should always use a voltmeter with what relative value of resistance?

Last Answer : . High.

What should a voltmeter read when a TX is set on coarse zero?

Description : What should a voltmeter read when a TX is set on coarse zero?

Last Answer : Approximately 37 volts.

What is the advantage of using a battery test set versus a voltmeter to test batteries?

Description : What is the advantage of using a battery test set versus a voltmeter to test batteries?

Last Answer : A battery test set will test batteries under load conditions.

A multimeter may be damaged by taking a _____________. A. voltage reading while in the ammeter mode B. current reading while in the voltmeter mode C. resistance reading while in the ammeter mode D. resistance reading while in the voltmeter mode

Description : A multimeter may be damaged by taking a _____________. A. voltage reading while in the ammeter mode B. current reading while in the voltmeter mode C. resistance reading while in the ammeter mode D. resistance reading while in the voltmeter mode

Last Answer : Answer: A

Prior to taking a resistance reading with a volt-ohm-milliammeter, the 'zero' setting must be adjusted. After clipping the two leads together, you find the adjustment knob will not return the pointer to 'zero'. This is most likely an indication of ______ A. an improper resistance range setting B. weak batteries C. a faulty zero ohms knob D. a faulty meter movement

Description : Prior to taking a resistance reading with a volt-ohm-milliammeter, the 'zero' setting must be adjusted. After clipping the two leads together, you find the adjustment knob will not return the pointer ... range setting B. weak batteries C. a faulty zero ohms knob D. a faulty meter movement

Last Answer : Answer: B

If the approximate voltage to be measured in a circuit is not known, you should _____________. A. use the lowest voltage range on the voltmeter B. connect the meter in series with the circuit C. only have to calibrate the meter before using it D. use the highest voltage range on the voltmeter

Description : If the approximate voltage to be measured in a circuit is not known, you should _____________. A. use the lowest voltage range on the voltmeter B. connect the meter in series with the circuit C. only have to calibrate the meter before using it D. use the highest voltage range on the voltmeter

Last Answer : Answer: D

What radar scope uses a range step for range measurement?

Description : What radar scope uses a range step for range measurement?

Last Answer : The A scope.

What range of an ammeter is selected for the final measurement?

Description : What range of an ammeter is selected for the final measurement?

Last Answer : A range that allows a meter reading near the center of the scale.

Why should you use the highest range of an ammeter for the initial measurement?

Description : Why should you use the highest range of an ammeter for the initial measurement?

Last Answer : To prevent damage to the meter movement from excessive current.

For measurement of potential difference, potentiometer is perferred in comparison to voltmeter because

Description : For measurement of potential difference, potentiometer is perferred in comparison to voltmeter because

Last Answer : For measurement of potential difference, potentiometer is perferred in comparison to voltmeter because A. ... does not take current from the circuit

In order to make an accurate measurement as possible, the internal resistance of a voltmeter must be

Description : In order to make an accurate measurement as possible, the internal resistance of a voltmeter must be

Last Answer : as high as possible

Ryall crest voltmeter is used for measurement of

Last Answer : Ryall crest voltmeter is used for measurement of High AC voltage.

Besides setting up the meter for expected voltage ranges, what must be strictly observed when taking dc voltage readings?

Description : Besides setting up the meter for expected voltage ranges, what must be strictly observed when taking dc voltage readings?

Last Answer : Polarit

What is the general function of the differential voltmeter?

Description : What is the general function of the differential voltmeter?

Last Answer : To compare an unknown voltage with a known reference voltage and indicate the difference in their values.

Why would you use a hook-on voltmeter instead of a multimeter?

Description : Why would you use a hook-on voltmeter instead of a multimeter?

Last Answer : To measure current safely and easily (with no need to disconnect the wiring of the circuit).

What method is used to allow a voltmeter to have several ranges?

Description : What method is used to allow a voltmeter to have several ranges?

Last Answer : The use of resistors in series with the meter movement.

What is voltmeter sensitivity?

Description : What is voltmeter sensitivity?

Last Answer : It is an indication of the resistance of the meter expressed in ohms per volt. The total resistance of the meter is the sensitivity multiplied by the full-scale voltage.

How is the loading effect of a voltmeter kept to a minimum?

Description : How is the loading effect of a voltmeter kept to a minimum?

Last Answer : A voltmeter must have a high resistance compared to the circuit being measured.

What is the loading effect of a voltmeter?

Description : What is the loading effect of a voltmeter?

Last Answer : The connection of a voltmeter adds a resistance in parallel with the circuit changing the total circuit resistance, and loads the circuit.

How is a voltmeter connected to the circuit to be measured?

Description : How is a voltmeter connected to the circuit to be measured?

Last Answer : In parallel.

What electrical quantity is measured by a voltmeter?

Description : What electrical quantity is measured by a voltmeter?

Last Answer : Voltage.

What term is used to express the sensitivity of a voltmeter?

Description : What term is used to express the sensitivity of a voltmeter?

Last Answer : Ohms per volt

What are the advantages of using a differential voltmeter?

Description : What are the advantages of using a differential voltmeter?

Last Answer : Accuracy and high input impedance.

When would you measure the minimum preheat temperature? a) On completion of each pass b) Immediately prior to commencing the first pass and subsequent passes c) When the welding is complete d) Minimum preheat temperature measurement is only required if the heat input is lower than that specified in WPS

Description : When would you measure the minimum preheat temperature? a) On completion of each pass b) Immediately prior to commencing the first pass and subsequent passes c) When the welding is ... preheat temperature measurement is only required if the heat input is lower than that specified in WPS

Last Answer : b) Immediately prior to commencing the first pass and subsequent passes

In addition to recovery time, what determines the minimum range of a radar set?

Description : In addition to recovery time, what determines the minimum range of a radar set?

Last Answer : Pulse width

When should wires be twisted prior to lacing?

Description : When should wires be twisted prior to lacing?

Last Answer : When required, such as for the filament leads in electron tube amplifiers.

Why must items to be soldered be cleaned just prior to the soldering process?

Description : Why must items to be soldered be cleaned just prior to the soldering process?

Last Answer : Solder will not adhere to dirty, greasy, or oxidized surfaces.

Should aluminum wire be cleaned prior to installing an aluminum terminal lug or splice?

Description : Should aluminum wire be cleaned prior to installing an aluminum terminal lug or splice?

Last Answer : No, it is done automatically by the petroleum abrasive compound that comes in the terminal or splices.

Prior to substituting a diode, what measurements should you take to determine its condition?

Description : Prior to substituting a diode, what measurements should you take to determine its condition?

Last Answer : Voltages and resistances.

A voltmeter of range 2 V and resistance `300 Omega` cannot be converted into ammeter of range

Description : A voltmeter of range 2 V and resistance `300 Omega` cannot be converted into ammeter of range

Last Answer : A voltmeter of range 2 V and resistance `300 Omega` cannot be converted into ammeter of range A. `1 A` B. `1 mA` C. `100 mA` D. `10 mA`

A milli voltmeter of 25 milli volt range is to be converted into an ammeter of 25 ampere range. The value (in ohm) of necessary shunt will be

Description : A milli voltmeter of 25 milli volt range is to be converted into an ammeter of 25 ampere range. The value (in ohm) of necessary shunt will be

Last Answer : A milli voltmeter of 25 milli volt range is to be converted into an ammeter of 25 ampere range. The value (in ohm) ... 001` B. `0.01` C. 1 D. `0.05`

The range of voltmeter is 10 V and its internal resistance is `50 Omega`. To convert it to voltmeter of range 15 V, how much resistance is to be added

Description : The range of voltmeter is 10 V and its internal resistance is `50 Omega`. To convert it to voltmeter of range 15 V, how much resistance is to be added

Last Answer : The range of voltmeter is 10 V and its internal resistance is `50 Omega`. To convert it to ... in parallel D. Add `125 Omega` resistor in series

Why voltmeter range extension need?

Description : Why voltmeter range extension need?

Last Answer : Need answer

Explain range extension for analog DC voltmeter.

Description : Explain range extension for analog DC voltmeter.

Last Answer : Explanation A DC voltmeter can be converted into a multirange voltmeter by connecting a number of resistors (multipliers) in series with the meter movement 

Draw the circuit diagram of multi range AC voltmeter and describe its working

Description : Draw the circuit diagram of multi range AC voltmeter and describe its working

Last Answer : The above circuit looks like a multi range AC voltmeter. We know that, we will get AC voltmeter just by placing rectifier in series (cascade) with DC voltmeter. The above circuit was created ... any two points of an electric circuit, by connecting the switch, S to the desired voltage range.

How range of A.C. ammeter & A.C. voltmeter is extended? Draw suitable diagram.

Description : How range of A.C. ammeter & A.C. voltmeter is extended? Draw suitable diagram.

Last Answer : Extension of A.C. Ammeter Range: The range of a.c. ammeter can be extended by using CT, the arrangement is shown in figure. The CT is current transformer having less number of primary turns carrying high ... high magnitude of source voltage. In this way range of a.c. voltmeter can be extended.

A digital voltmeter has a read-out range from 0 to 9999 counts. When full scale reading is 9.999 V, the

Description : A digital voltmeter has a read-out range from 0 to 9999 counts. When full scale reading is 9.999 V, the resolution of the instrument will be (a) 100 mV (b) 99 mV (c) 9 mV (d) 1 mV 

Last Answer : d) 1mV 9.999v÷9999v

In order to increase the range of a voltmeter

Description : In order to increase the range of a voltmeter

Last Answer : In order to increase the range of a voltmeter a high resistance is connected in series

Range of a voltmeter can be extended by connecting a

Description : Range of a voltmeter can be extended by connecting a

Last Answer : Range of a voltmeter can be extended by connecting a Multiplier in series

A dc voltmeter has a sensitivity of 1000 Ohm/V. When it measures half full scale in 100 V range, the current ...

Description : A dc voltmeter has a sensitivity of 1000 Ohm/V. When it measures half full scale in 100 V range, the current through the voltmeter is

Last Answer : A dc voltmeter has a sensitivity of 1000 Ohm/V. When it measures half full scale in 100 V range, the current through the voltmeter is 1 mA.

Should state department travel warnings be consulted prior to taking trips across the US Mexican border?

Description : Should state department travel warnings be consulted prior to taking trips across the US Mexican border?

Last Answer : State Department Travel Warnings should be consulted prior totaking trips across the US-Mexican border

Why isn't the Marines taking prior service Marines I was told this by a recruiter.?

Description : Why isn't the Marines taking prior service Marines I was told this by a recruiter.?

Last Answer : The military is downsizing quite a bit and are recruiting less and less people. It's due to the economy. You should try again though, never give up your dreams.

Which of the following statements represents the correct method of connecting the shunt of an ammeter prior to taking a reading? A. In series with the load and in series with the meter movement. B. In series with the load and in parallel with the meter movement. C. In parallel with the load and in series with the meter movement. D. In parallel with the load and in parallel with the meter movement.

Description : Which of the following statements represents the correct method of connecting the shunt of an ammeter prior to taking a reading? A. In series with the load and in series with the meter movement. B. In ... with the meter movement. D. In parallel with the load and in parallel with the meter movement.

Last Answer : Answer: B

Which of the following is most likely to be a response to the auditor's assessment that the risk of material misstatement due to fraud for the existence of inventory is high? a. Observe test counts of inventory at certain locations on an unannounced basis. b. Perform analytical procedures rather than taking test counts. c. Request that inventories be counted prior to year end. d. Request that inventory counts at the various locations be counted on different dates so as to allow the same auditor to be present at every count

Description : Which of the following is most likely to be a response to the auditor's assessment that the risk of material misstatement due to fraud for the existence of inventory is high? a. Observe test counts ... be counted on different dates so as to allow the same auditor to be present at every count

Last Answer : Observe test counts of inventory at certain locations on an unannounced basis.

A lead line or sounding line (A) Is stretched thoroughly when wet before it is graduated (B) Should be soaked in water for about one hour prior to taking soundings (C) Is adjusted at regular interval (D) All the above

Description : A lead line or sounding line (A) Is stretched thoroughly when wet before it is graduated (B) Should be soaked in water for about one hour prior to taking soundings (C) Is adjusted at regular interval (D) All the above

Last Answer : (D) All the above