A two port network having a 6 dB loss will give

A two port network having a 6 dB loss will give 

(A) an output power which is one - quarter of the input power (B) an output power which is one - half of the input power (C) an output voltage which is 0.707 of the input voltage. (D) an output power which is 0.707 of the input power.
by

1 Answer

Answer :

A two port network having a 6 dB loss will give an output power which is one - quarter of the input power

by

Related questions

The capacity of a standard 4 KHz telephone channel with a 32 dB SNR is

Description : The capacity of a standard 4 KHz telephone channel with a 32 dB SNR is

Last Answer : The capacity of a standard 4 KHz telephone channel with a 32 dB SNR is 32953 bits/second

If two parallel-connected resistors dissipate 6 watts and 10 watts of power, then what is the total power loss?

Last Answer : If two parallel-connected resistors dissipate 6 watts and 10 watts of power, then 16 watts is the total power loss.

You are measuring noise at a -6 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -59 dBm. This is _________ dBa0. A. 24 B. 12 C. 23 D. 32

Description : You are measuring noise at a -6 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -59 dBm. This is _________ dBa0. A. 24 B. 12 C. 23 D. 32

Last Answer : D. 32

The total space loss of transmission and reception for two ground stations with uplink frequency 8GHz and a downlink of 6 GHz with angle of elevations of 3˚ and 7˚ A respectively is A. 403 dB B. 100 dB C. 20 dB D. 215 dB

Description : The total space loss of transmission and reception for two ground stations with uplink frequency 8GHz and a downlink of 6 GHz with angle of elevations of 3˚ and 7˚ A respectively is A. 403 dB B. 100 dB C. 20 dB D. 215 dB

Last Answer : A. 403 dB

What is the free space loss, in dB, between two microwave parabolic antennas 38.0 kilometer apart operating at 7.0 GHz? A. 145.6 dB B. 138.5 dB C. 135.5 dB D. 140.89 dB

Description : What is the free space loss, in dB, between two microwave parabolic antennas 38.0 kilometer apart operating at 7.0 GHz? A. 145.6 dB B. 138.5 dB C. 135.5 dB D. 140.89 dB

Last Answer : D. 140.89 dB

What is the effective radiated power of a repeater with 120 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 6 dB antenna gain? A. 601 W B. 240 W C. 60 W D. 379 W

Description : What is the effective radiated power of a repeater with 120 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 6 dB antenna gain? A. 601 W B. 240 W C. 60 W D. 379 W

Last Answer : C. 60 W

What is the effective radiated power of a repeater with 75 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 6 dB antenna gain? A. 37.6 W B. 237 W C. 150 W D. 23.7 W

Description : What is the effective radiated power of a repeater with 75 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 6 dB antenna gain? A. 37.6 W B. 237 W C. 150 W D. 23.7 W

Last Answer : A. 37.6 W

What is the effective radiated power of a repeater with 50 watts transmitter power output \, 4 dB feedline loss, 3 dB duplexer and circulator loss, and 6 dB antenna gain? A. 158 W B. 39.7 W C. 251 W D. 69.9 W

Description : What is the effective radiated power of a repeater with 50 watts transmitter power output \, 4 dB feedline loss, 3 dB duplexer and circulator loss, and 6 dB antenna gain? A. 158 W B. 39.7 W C. 251 W D. 69.9 W

Last Answer : B. 39.7 W

If a transmission line has a power loss of 6 dB per 100 feet, what is the power at the feed point to the antenna at the end of a 200 foot transmission line fed by a 100 watt transmitter? A. 70 watts B. 50 watts C. 25 watts D. 6 watts

Description : If a transmission line has a power loss of 6 dB per 100 feet, what is the power at the feed point to the antenna at the end of a 200 foot transmission line fed by a 100 watt transmitter? A. 70 watts B. 50 watts C. 25 watts D. 6 watts

Last Answer : D. 6 watts

What is the power loss of a telephone hybrid? A. 6 dB B. 2 dB C. 3 dB D. 1 dB

Description : What is the power loss of a telephone hybrid? A. 6 dB B. 2 dB C. 3 dB D. 1 dB

Last Answer : C. 3 dB

You are measuring noise at a +3 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -57dBm. This is ________dBa0. A. 20 B. 15 C. 25 D. 17

Description : You are measuring noise at a +3 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -57dBm. This is ________dBa0. A. 20 B. 15 C. 25 D. 17

Last Answer : C. 25

Cable attenuation is usually expressed in terms of a. Loss per foot b. dB/km c. intensity per mile d. voltage drop per inch

Description : Cable attenuation is usually expressed in terms of a. Loss per foot b. dB/km c. intensity per mile d. voltage drop per inch

Last Answer : b. dB/km

When the elevation angle of a geostationary satellite is 23˚ and the transmitting frequency is 3840 MHz, what is the free space loss in dB? A. 196 dB B. 200 dB C. 150 dB D. 100 dB

Description : When the elevation angle of a geostationary satellite is 23˚ and the transmitting frequency is 3840 MHz, what is the free space loss in dB? A. 196 dB B. 200 dB C. 150 dB D. 100 dB

Last Answer : A. 196 dB

What is the approximate path loss from satellite-to-earth station? A. 100 dB B. 150 dB C. 175 dB D. 200 dB

Description : What is the approximate path loss from satellite-to-earth station? A. 100 dB B. 150 dB C. 175 dB D. 200 dB

Last Answer : D. 200 dB

What is the effective radiated power of a repeater with 200 watts transmitter power output, 4 dB feline loss, 4 dB duplexer and circulator loss, and 10 dB antenna gain? A. 317 W B. 2000 W C. 126 W D. 260 W

Description : What is the effective radiated power of a repeater with 200 watts transmitter power output, 4 dB feline loss, 4 dB duplexer and circulator loss, and 10 dB antenna gain? A. 317 W B. 2000 W C. 126 W D. 260 W

Last Answer : A. 317 W

What is the insertion loss of connector type splices for a single mode optical fiber? A. 0.51 dB B. 0.49 dB C. 0.31 dB D. 0.38 db

Description : What is the insertion loss of connector type splices for a single mode optical fiber? A. 0.51 dB B. 0.49 dB C. 0.31 dB D. 0.38 db

Last Answer : D. 0.38 db

What is the effective radiated power of a repeater with 100 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 10 dB antenna gain? A. 800 W B. 126 W C. 12.5 W D. 1260 W

Description : What is the effective radiated power of a repeater with 100 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 10 dB antenna gain? A. 800 W B. 126 W C. 12.5 W D. 1260 W

Last Answer : B. 126 W

What is the effective radiated power of a repeater with 75 watts transmitter power output, 4 dB feedline loss, 3 dB duplexer and circulator loss, and 10 dB antenna gain? A. 600 W B. 75 W C. 18.75 W D. 150 W

Description : What is the effective radiated power of a repeater with 75 watts transmitter power output, 4 dB feedline loss, 3 dB duplexer and circulator loss, and 10 dB antenna gain? A. 600 W B. 75 W C. 18.75 W D. 150 W

Last Answer : D. 150 W

What is the effective radiated power of a repeater with 50 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 7 dB antenna gain? A. 300 W B. 315 W C. 31.5 W D. 69.9 W

Description : What is the effective radiated power of a repeater with 50 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 7 dB antenna gain? A. 300 W B. 315 W C. 31.5 W D. 69.9 W

Last Answer : C. 31.5 W

A properly matched transmission line has a loss of 1.5 dB/100m. if 10 W is supplied to one end of the line, how many watts reach the load, 27 m away? A. 10 W B. 7.2 W C. 9.9 W D. 9.1 W

Description : A properly matched transmission line has a loss of 1.5 dB/100m. if 10 W is supplied to one end of the line, how many watts reach the load, 27 m away? A. 10 W B. 7.2 W C. 9.9 W D. 9.1 W

Last Answer : D. 9.1 W

Determine the terrain sensitivity loss for a 4-GHz carrier that is propagating over a very dry, mountainous area. A. -1.25 dB B. -3.05 dB C. -2.01 dB D. -5.01 dB

Description : Determine the terrain sensitivity loss for a 4-GHz carrier that is propagating over a very dry, mountainous area. A. -1.25 dB B. -3.05 dB C. -2.01 dB D. -5.01 dB

Last Answer : A. -1.25 dB

The standard deviation of the variation in the transmission loss of a circuit should not exceed A. 3 dB B. 1 dB C. 5 dB D. 0.5dB

Description : The standard deviation of the variation in the transmission loss of a circuit should not exceed A. 3 dB B. 1 dB C. 5 dB D. 0.5dB

Last Answer : B. 1 dB

Insertion loss of connector-type splices for a single-mode fiber cable. A. 0.2 dB B. 0.3 dB C. 0.09 dB D. 0.38 dB

Description : Insertion loss of connector-type splices for a single-mode fiber cable. A. 0.2 dB B. 0.3 dB C. 0.09 dB D. 0.38 dB

Last Answer : D. 0.38 dB

Cable attenuation is usually expressed in terms of ∙ A. loss per foot ∙ B. dB/km ∙ C. intensity per mile ∙ D. voltage drop per inch

Description : Cable attenuation is usually expressed in terms of ∙ A. loss per foot ∙ B. dB/km ∙ C. intensity per mile ∙ D. voltage drop per inch

Last Answer : . dB/km

For a single mode optical cable with 0.25 dB/km loss, determine the optical power 100 km from a 0.1-mW light source. ∙ A. -45 dBm ∙ B. -15 dBm ∙ C. -35 dBm

Description : For a single mode optical cable with 0.25 dB/km loss, determine the optical power 100 km from a 0.1-mW light source. ∙ A. -45 dBm ∙ B. -15 dBm ∙ C. -35 dBm

Last Answer : ∙ C. -35 dBm

A fiber-optic cable has a loss of 15 dB/km. The attenuation in a cable 1000 ft. long is ∙ A. 4.57 dB ∙ B. 9.3 dB ∙ C. 24 dB ∙ D. 49.2 dB

Description : A fiber-optic cable has a loss of 15 dB/km. The attenuation in a cable 1000 ft. long is ∙ A. 4.57 dB ∙ B. 9.3 dB ∙ C. 24 dB ∙ D. 49.2 dB

Last Answer : A. 4.57 dB

Fiber-optic cables with attenuation of 1.8, 3.4, 5.9 and 18 dB are linked together. The total loss is ∙ A. 7.5 dB ∙ B. 19.8 dB ∙ C. 29.1 dB ∙ D. 650 dB

Description : Fiber-optic cables with attenuation of 1.8, 3.4, 5.9 and 18 dB are linked together. The total loss is ∙ A. 7.5 dB ∙ B. 19.8 dB ∙ C. 29.1 dB ∙ D. 650 dB

Last Answer : C. 29.1 dB

How much is the power loss of the fusion splice? ∙ a. 0.1 dB or less ∙ b. 0.01 dB or less ∙ c. 1 dB or less ∙ d. 10 dB or less

Description : How much is the power loss of the fusion splice? ∙ a. 0.1 dB or less ∙ b. 0.01 dB or less ∙ c. 1 dB or less ∙ d. 10 dB or less

Last Answer : a. 0.1 dB or less

The mechanical splice attenuation loss is _____ dB or less ∙ a. 0.1 ∙ b. 0.01 ∙ c. 0.001 ∙ d. 1

Description : The mechanical splice attenuation loss is _____ dB or less ∙ a. 0.1 ∙ b. 0.01 ∙ c. 0.001 ∙ d. 1

Last Answer : a. 0.1

What is the average loss in fiber splice? ∙ a. 0.10 dB ∙ b. 0.15 dB ∙ c. 0.20 dB ∙ d. 0.25 dB

Description : What is the average loss in fiber splice? ∙ a. 0.10 dB ∙ b. 0.15 dB ∙ c. 0.20 dB ∙ d. 0.25 dB

Last Answer : 0.15 dB

Fiber-optic cables with attenuations of 1.8, 3.4, 5.9, and 18 dB are linked together. The total loss is ∙ a. 7.5 dB ∙ b. 19.8 dB ∙ c. 29.1 dB ∙ d. 650 dB

Description : Fiber-optic cables with attenuations of 1.8, 3.4, 5.9, and 18 dB are linked together. The total loss is ∙ a. 7.5 dB ∙ b. 19.8 dB ∙ c. 29.1 dB ∙ d. 650 dB

Last Answer : ∙ c. 29.1 dB

. A fiber-optic cable has a loss of 15 dB/km. The attenuation in a cable, 100 ft long is ∙ a. 4.57 dB ∙ b. 9.3 dB ∙ c. 24 dB ∙ d. 49.2 dB

Description : . A fiber-optic cable has a loss of 15 dB/km. The attenuation in a cable, 100 ft long is ∙ a. 4.57 dB ∙ b. 9.3 dB ∙ c. 24 dB ∙ d. 49.2 dB

Last Answer : ∙ a. 4.57 dB

Cable attenuation is usually expressed in terms of ∙ a. Loss per foot ∙ b. dB/km ∙ c. intensity per mile ∙ d. voltage drop per inch

Description : Cable attenuation is usually expressed in terms of ∙ a. Loss per foot ∙ b. dB/km ∙ c. intensity per mile ∙ d. voltage drop per inch

Last Answer : ∙ b. dB/km

What is the insertion loss of connector-type splices for a single mode fiber optics? ∙ a. 0.51 dB ∙ b. 0.31 dB ∙ c. 0.49 dB ∙ d. 0.38 dB

Description : What is the insertion loss of connector-type splices for a single mode fiber optics? ∙ a. 0.51 dB ∙ b. 0.31 dB ∙ c. 0.49 dB ∙ d. 0.38 dB

Last Answer : d. 0.38 dB

What is the average insertion loss of fusion splice in fiber optics? ∙ a. 0.09 dB ∙ b. 0.9 dB ∙ c. 0.19 dB ∙ d. 0.009 dB

Description : What is the average insertion loss of fusion splice in fiber optics? ∙ a. 0.09 dB ∙ b. 0.9 dB ∙ c. 0.19 dB ∙ d. 0.009 dB

Last Answer : ∙ b. 0.9 dB

The loss in single-mode fiber-optic cable due to a connector is about: a. 0.02 dB b. 0.2 dB c. 1 dB d. 3 dB

Description : The loss in single-mode fiber-optic cable due to a connector is about: a. 0.02 dB b. 0.2 dB c. 1 dB d. 3 dB

Last Answer : b. 0.2 dB

The loss in single-mode fiber-optic cable due to a splice is about: a. 0.02 dB b. 0.2 dB c. 1 dB d. 3 dB

Description : The loss in single-mode fiber-optic cable due to a splice is about: a. 0.02 dB b. 0.2 dB c. 1 dB d. 3 dB

Last Answer : a. 0.02 dB

The loss in single-mode fiber-optic cable due to the glass is about: a. 40 dB per km b. 4 db per km c. 0.4 dB per km d. zero loss

Description : The loss in single-mode fiber-optic cable due to the glass is about: a. 40 dB per km b. 4 db per km c. 0.4 dB per km d. zero loss

Last Answer : c. 0.4 dB per km

Three identical circuits having 10 dB signal noise-to-noise ratio each are connected in tandem with each other, what is the overall S/N? A. 5.23 dB B. 14.77dB C. 30 dB D. 40 dB

Description : Three identical circuits having 10 dB signal noise-to-noise ratio each are connected in tandem with each other, what is the overall S/N? A. 5.23 dB B. 14.77dB C. 30 dB D. 40 dB

Last Answer : A. 5.23 dB

Three telephone circuits, each having an S/N ratio of 44 dB, are connected in tandem. What is the overall S/N ratio? A. 44 dB B. 39.2 dB C. 41 dB D. 43.52 dB

Description : Three telephone circuits, each having an S/N ratio of 44 dB, are connected in tandem. What is the overall S/N ratio? A. 44 dB B. 39.2 dB C. 41 dB D. 43.52 dB

Last Answer : B. 39.2 dB

A passive two port network is in a steady state. Compared to its input, the steady state output can never offer

Description : A passive two port network is in a steady state. Compared to its input, the steady state output can never offer  A) Higher voltage B) Lower impedance C) Greater power D) Better regulation

Last Answer : A passive two port network is in a steady state. Compared to its input, the steady state output can never offer Greater power

Two port networks are connected in cascade. The parameters of the network are obtained by multiplying in individual

Description : Two port networks are connected in cascade. The parameters of the network are obtained by multiplying in individual

Last Answer : Two port networks are connected in cascade. The parameters of the network are obtained by multiplying in individual ABCD parameter matrix

For a two -port reciprocal network, the three transmission parameters are A = 4, B = 7 and C = 5. ...

Description : For a two -port reciprocal network, the three transmission parameters are A = 4, B = 7 and C = 5. What is the value of D ?  (a) 9.5 (b) 9.0 (c) 8.5 (d) 8.0

Last Answer : For a two -port reciprocal network, the three transmission parameters are A = 4, B = 7 and C = 5. What is the value of D ?  (a) 9.5 (b) 9.0 (c) 8.5 (d) 8.0

A Two-Port Network is said to be symmetrical when the following equalities hold good

Description : A Two-Port Network is said to be symmetrical when the following equalities hold good (A) Z11 = Z22 and Z12 = Z21 (B) Z11 = Z22 (C) Y12 = Y21 (D) Y11 = Y22 and Y12 = Y21

Last Answer : A Two-Port Network is said to be symmetrical when the following equalities hold good Z11 = Z22

How do you instal the Tritton 4-USB Port Network Hub & Switch?

Description : How do you instal the Tritton 4-USB Port Network Hub & Switch?

Last Answer : Simply plug into your network and share 4 USB ports.

An endpoint of an inter-process communication flow across a computer network is called a. socket b. pipe c. port d. machine

Description : An endpoint of an inter-process communication flow across a computer network is called a. socket b. pipe c. port d. machine

Last Answer : a. socket

An endpoint of an inter-process communication flow across a computer network is called a. socket b. pipe c. port d. machine

Description : An endpoint of an inter-process communication flow across a computer network is called a. socket b. pipe c. port d. machine

Last Answer : a. socket

Which of the following used for the Network Testing and port scanning A)NetCat B)SuperScan C)NetScan D)All of Above

Description : Which of the following used for the Network Testing and port scanning A)NetCat B)SuperScan C)NetScan D)All of Above

Last Answer : D)All of Above

Network Testing and port scanning tools are : a. Sam Spade b. SuperScan c. NetScan d. All of the above

Description : Network Testing and port scanning tools are : a. Sam Spade b. SuperScan c. NetScan d. All of the above

Last Answer : d. All of the above

. As an ethical hacker, you should scan all ________ UDP and TCP port on each network host that’s found by your scanner. a. 65535 b. 65353 c. 65333 d. 65555

Description : . As an ethical hacker, you should scan all ________ UDP and TCP port on each network host that’s found by your scanner. a. 65535 b. 65353 c. 65333 d. 65555

Last Answer : a. 65535