The capacity of a standard 4 KHz telephone channel with a 32 dB SNR is

The capacity of a standard 4 KHz telephone channel with a 32 dB SNR is
by

1 Answer

Answer :

The capacity of a standard 4 KHz telephone channel with a 32 dB SNR is 32953 bits/second

by

Related questions

What is the channel bandwidth of a standard analogue telephone system? A. 300-500 Hz B. 1200 kHz C. 100-300 Hz D. 300-3400 Hz

Description : What is the channel bandwidth of a standard analogue telephone system? A. 300-500 Hz B. 1200 kHz C. 100-300 Hz D. 300-3400 Hz

Last Answer : D. 300-3400 Hz

The bandwidth requirement of a telephone channel is (A) 3 KHz (B) 15 KHz (C) 5 KHz (D) 25 KHz

Description : The bandwidth requirement of a telephone channel is (A) 3 KHz (B) 15 KHz (C) 5 KHz (D) 25 KHz

Last Answer : (A) 3 KHz

Suppose a digitized voice channel is made by digitizing 8 kHz bandwidth analog voice signal. It is required to sample the signal at twice the highest frequency (two samples per hertz). What is the bit rate required, if it is assumed that each sample requires 8 bits? (A) 32 kbps (B) 64 kbps (C) 128 kbps (D) 256 kbps

Description : Suppose a digitized voice channel is made by digitizing 8 kHz bandwidth analog voice signal. It is required to sample the signal at twice the highest frequency (two samples per hertz). What is the bit rate required, if it ... sample requires 8 bits? (A) 32 kbps (B) 64 kbps (C) 128 kbps (D) 256 kbps

Last Answer : (C) 128 kbps

You are measuring noise in a voice channel at 7 dB test point level. The meter reads -56 dBm (FIA weighted). What is the reading in dBrnc? A. 20 B. 32 C. 35 D. 25

Description : You are measuring noise in a voice channel at 7 dB test point level. The meter reads -56 dBm (FIA weighted). What is the reading in dBrnc? A. 20 B. 32 C. 35 D. 25

Last Answer : C. 35

The signal in a channel is measured to be 23 dB while noise in the same channel is measured to be 9 dB. The signal to noise ratio therefore is __________. A. 9/23 B. 23/9 C. 32 dB D. 14 dB

Description : The signal in a channel is measured to be 23 dB while noise in the same channel is measured to be 9 dB. The signal to noise ratio therefore is __________. A. 9/23 B. 23/9 C. 32 dB D. 14 dB

Last Answer : D. 14 dB

In a PCM system the number of quantization level are 16 and the maximum signal frequency is 4 KHz the

Description : In a PCM system the number of quantization level are 16 and the maximum signal frequency is 4 KHz the transmission bit rate is

Last Answer : In a PCM system the number of quantization level are 16 and the maximum signal frequency is 4 KHz the transmission bit rate is 32 Kbits/sec

A tuned circuit has a Q of 100 at its resonant frequency of 500 kHz. Its bandwidth is _____kHz.

Description : A tuned circuit has a Q of 100 at its resonant frequency of 500 kHz. Its bandwidth is _____kHz. (A) 50000 (B) 0.2 (C) 600 (D) 5

Last Answer : A tuned circuit has a Q of 100 at its resonant frequency of 500 kHz. Its bandwidth is 5 kHz.

At what power level does a 1 KHz tone cause zero interference (144 weighted)? A. 90 dB B. 90 dBm C. -90 dBm D. -90 dBm

Description : At what power level does a 1 KHz tone cause zero interference (144 weighted)? A. 90 dB B. 90 dBm C. -90 dBm D. -90 dBm

Last Answer : D. -90 dBm

ECE Board Exam March 1996 At what power level does a 1 kHz tone cause zero interference (144 weighted) ? A. -90 dB B. -90 dBm C. 90 dBm D. 90 dB

Description : ECE Board Exam March 1996 At what power level does a 1 kHz tone cause zero interference (144 weighted) ? A. -90 dB B. -90 dBm C. 90 dBm D. 90 dB

Last Answer : B. -90 dBm

The frequency-response specification of your tape recorder reads within +/ - 3 dB from 150 Hz to 150 kHz at 60 ips. What does this mean?

Description : The frequency-response specification of your tape recorder reads within +/ - 3 dB from 150 Hz to 150 kHz at 60 ips. What does this mean?

Last Answer : The recorder can record all frequencies between 150 Hz and 150 kHz at 60 ips without varying the output amplitude more than 3 dB.

A two port network having a 6 dB loss will give

Description : A two port network having a 6 dB loss will give  (A) an output power which is one - quarter of the input power (B) an output power which is one - half of the input power (C) an output voltage which is 0.707 of the input voltage. (D) an output power which is 0.707 of the input power.

Last Answer : A two port network having a 6 dB loss will give an output power which is one - quarter of the input power

Distortion caused on telephone line by an adjacent one is called:

Last Answer : Distortion caused on telephone line by an adjacent one is called: Cross talk

The most modern telephone exchange system is:

Last Answer : The most modern telephone exchange system is: Electronic system.

In the telephone, the dial tone has a frequency of

Last Answer : In the telephone, the dial tone has a frequency of 33 Hz.

Three telephone circuits, each having an S/N ratio of 44 dB, are connected in tandem. What is the overall S/N ratio? A. 44 dB B. 39.2 dB C. 41 dB D. 43.52 dB

Description : Three telephone circuits, each having an S/N ratio of 44 dB, are connected in tandem. What is the overall S/N ratio? A. 44 dB B. 39.2 dB C. 41 dB D. 43.52 dB

Last Answer : B. 39.2 dB

What signal-to-noise ratio is required for satisfactory telephone services? A. 50 dB B. 30 dB C. 40dB D. 20 dB

Description : What signal-to-noise ratio is required for satisfactory telephone services? A. 50 dB B. 30 dB C. 40dB D. 20 dB

Last Answer : A. 50 dB

What is the power loss of a telephone hybrid? A. 6 dB B. 2 dB C. 3 dB D. 1 dB

Description : What is the power loss of a telephone hybrid? A. 6 dB B. 2 dB C. 3 dB D. 1 dB

Last Answer : C. 3 dB

What is the channel spacing for SITOR frequencies? A. 500 Hz B. 170 Hz C. 300 Hz D. 3 kHz

Description : What is the channel spacing for SITOR frequencies? A. 500 Hz B. 170 Hz C. 300 Hz D. 3 kHz

Last Answer : A. 500 Hz

What is the channel spacing for MF-HF voice frequencies? A. 2.8 kHz B. 500 Hz C. 3.5 kHz D. 3 kHz

Description : What is the channel spacing for MF-HF voice frequencies? A. 2.8 kHz B. 500 Hz C. 3.5 kHz D. 3 kHz

Last Answer : D. 3 kHz

A superhet receiver has an IF of 455 kHz and is experiencing image-channel interference on a frequency of 1570 kHz. The receiver is tuned to A. 1115 kHz B. 660 kHz C. 2025 kHz D. 910 kHz

Description : A superhet receiver has an IF of 455 kHz and is experiencing image-channel interference on a frequency of 1570 kHz. The receiver is tuned to A. 1115 kHz B. 660 kHz C. 2025 kHz D. 910 kHz

Last Answer : B. 660 kHz

Assume a frequency range of 405.0125 MHz to 405.0875 MHz and 25 kHz channeling plan, determine the center frequency of the second channel from the lower limit. A. 405.030 MHz B. 405.025 MHz C. 405.050 MHz D. 405.075 MHz

Description : Assume a frequency range of 405.0125 MHz to 405.0875 MHz and 25 kHz channeling plan, determine the center frequency of the second channel from the lower limit. A. 405.030 MHz B. 405.025 MHz C. 405.050 MHz D. 405.075 MHz

Last Answer : C. 405.050 MHz

Assume a frequency range of 401.000 MHz to 401.050 MHz, if you apply 25 kHz channeling plan, determine the center frequency of the first channel from the lower limit. A. 401.010 MHz B. 401.0125 MHz C. 401.025 MHz D. 401.00625 MHz

Description : Assume a frequency range of 401.000 MHz to 401.050 MHz, if you apply 25 kHz channeling plan, determine the center frequency of the first channel from the lower limit. A. 401.010 MHz B. 401.0125 MHz C. 401.025 MHz D. 401.00625 MHz

Last Answer : B. 401.0125 MHz

If frequency range of 401.000MHz to 401.050MHz has to be channelized at 12.5 kHz between channel, what is the center of its first channel from the lower limit? A. 401.125MHz B. 401.00625MHz C. 401.025MHz D. 401.0125MHz

Description : If frequency range of 401.000MHz to 401.050MHz has to be channelized at 12.5 kHz between channel, what is the center of its first channel from the lower limit? A. 401.125MHz B. 401.00625MHz C. 401.025MHz D. 401.0125MHz

Last Answer : B. 401.00625MHz

Nominal voice channel A. 20 to 20 KHz B. 16 to 16 KHz C. 3 to 3 KHz D. 4 KHz

Description : Nominal voice channel A. 20 to 20 KHz B. 16 to 16 KHz C. 3 to 3 KHz D. 4 KHz

Last Answer : D. 4 KHz

What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

Description : What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice ... a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

Last Answer : C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz

A noiseless 3 KHz Channel transmits bits with binary level signals. What is the maximum data rate? A. 3 Kbps B. 6 Kbps C. 12 Kbps D. 24 Kbps

Description : A noiseless 3 KHz Channel transmits bits with binary level signals. What is the maximum data rate? A. 3 Kbps B. 6 Kbps C. 12 Kbps D. 24 Kbps

Last Answer : 6 Kbps

How many voice channels are supported for each 30 KHz radio channel in IS-136? a) Eight b) Thirty c) Three d) Sixteen

Description : How many voice channels are supported for each 30 KHz radio channel in IS-136? a) Eight b) Thirty c) Three d) Sixteen

Last Answer : c) Three

How many users or voice channels are supported for each 200 KHz channel in GSM? a) Eight b) Three c) Sixty four d) Twelve

Description : How many users or voice channels are supported for each 200 KHz channel in GSM? a) Eight b) Three c) Sixty four d) Twelve

Last Answer : a) Eight

What is the full form of SNR ?

Last Answer : The full form of SRN is Signal-to-noise ration.

Which performance parameter is the minimum amount of optical power required to achieve a specific bit-error rate (BER) in digital systems or a given signal-to-noise ratio (SNR) in analog systems?

Description : Which performance parameter is the minimum amount of optical power required to achieve a specific bit-error rate (BER) in digital systems or a given signal-to-noise ratio (SNR) in analog systems?

Last Answer : Receiver sensitivity.

Technical manuals for tape recorders can state the SNR in what three different ways?

Description : Technical manuals for tape recorders can state the SNR in what three different ways?

Last Answer : a. Root-mean-square (RMS) signal-to-RMS noise. b. Peak-to-peak signal-to-RMS noise. c. Peak signal-to-RMS noise.

You plan to measure your tape recorder’s SNR. What test equipment will you need?

Description : You plan to measure your tape recorder’s SNR. What test equipment will you need?

Last Answer : A VTVM and a signal generator.

Why does adding dc vice ac bias voltage to the input signal result in a poor signal-to-noise ratio (SNR)?

Description : Why does adding dc vice ac bias voltage to the input signal result in a poor signal-to-noise ratio (SNR)?

Last Answer : With dc bias, the SNR is poor because only a small portion of the magnetism curve is straight enough to use, thus the output signal is weak compared with the natural tape hiss.

To avoid objectionable noise in a microwave TV link, the SNR should be about:

Description : To avoid objectionable noise in a microwave TV link, the SNR should be about:

Last Answer : 25 or more

SNR is: A. Signal to Noise Ratio B. Signal to Net Ratio C. Signal to Noise Rate D. None of above

Description : SNR is: A. Signal to Noise Ratio B. Signal to Net Ratio C. Signal to Noise Rate D. None of above

Last Answer : A. Signal to Noise Ratio

The threshold effect in demodulators is a The rapid fall of output SNR when the input SNR falls below

Description : The threshold effect in demodulators is a) The rapid fall of output SNR when the input SNR falls below a particular value b) Exhibited by all the demodulators when the input SNR is low c) Exhibited by all AM suppressed carrier coherent demodulators d) Exhibited by correlation receivers

Last Answer : The threshold effect in demodulators is The rapid fall of output SNR when the input SNR falls below a particular value

You are measuring a voice channel at a -4 dB test point level, the meter reads -73 dBm (pure test tone) convert the reading in dBmCO. A. 16 B. 18 C. 22 D. 12

Description : You are measuring a voice channel at a -4 dB test point level, the meter reads -73 dBm (pure test tone) convert the reading in dBmCO. A. 16 B. 18 C. 22 D. 12

Last Answer : C. 22

In measuring noise in a voice channel at a 4 dB test point level, the meter reads -70 dBm (F1A weighted), convert the reading to pWp. A. 53 B. 93 C. 63 D. 83

Description : In measuring noise in a voice channel at a 4 dB test point level, the meter reads -70 dBm (F1A weighted), convert the reading to pWp. A. 53 B. 93 C. 63 D. 83

Last Answer : B. 93

You are measuring noise at a -6 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -59 dBm. This is _________ dBa0. A. 24 B. 12 C. 23 D. 32

Description : You are measuring noise at a -6 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -59 dBm. This is _________ dBa0. A. 24 B. 12 C. 23 D. 32

Last Answer : D. 32

What is the baseband frequency of standard FDM basic supergroup? A. 312 to 552 kHz B. 300 to 600 kHz C. 60 to 2540 kHz D. 60 to 108 kHz

Description : What is the baseband frequency of standard FDM basic supergroup? A. 312 to 552 kHz B. 300 to 600 kHz C. 60 to 2540 kHz D. 60 to 108 kHz

Last Answer : A. 312 to 552 kHz

In CCIR system B standard, the line frequency

Last Answer : In CCIR system B standard, the line frequency 15,625 lines/sec.

dB is a standard abbreviation used for the quantitaive expression of :

Description : dB is a standard abbreviation used for the quantitaive expression of :

Last Answer : dB is a standard abbreviation used for the quantitaive expression of : A. A particular pollutants B. The ... D. The density of bacteria in a medium.

dB is a standard abbreviation used for the quantitaive expression of :

Description : dB is a standard abbreviation used for the quantitaive expression of :

Last Answer : dB is a standard abbreviation used for the quantitaive expression of : A. the density of bacteria ... Bacillus in a culture D. a certain pesticide

The agreed standard for measuring loudness is the loudness sensation produced by a 1000 Hz sine wave _____ dB above the listener’s threshold of hearing. A. 80 B. 50 C. 30 D. 40

Description : The agreed standard for measuring loudness is the loudness sensation produced by a 1000 Hz sine wave _____ dB above the listener’s threshold of hearing. A. 80 B. 50 C. 30 D. 40

Last Answer : D. 40

The standard deviation of the variation in the transmission loss of a circuit should not exceed A. 3 dB B. 1 dB C. 5 dB D. 0.5dB

Description : The standard deviation of the variation in the transmission loss of a circuit should not exceed A. 3 dB B. 1 dB C. 5 dB D. 0.5dB

Last Answer : B. 1 dB

The standard test tone A. 0dB B. 10 dBm C. 0 dBm D. 10 dB

Description : The standard test tone A. 0dB B. 10 dBm C. 0 dBm D. 10 dB

Last Answer : C. 0 dBm

ECE Board Exam March 1996 The power of standard test tone is normally ____________. A. 1 dB B. 0 mW C. 1 mW D. 1 W

Description : ECE Board Exam March 1996 The power of standard test tone is normally ____________. A. 1 dB B. 0 mW C. 1 mW D. 1 W

Last Answer : C. 1 mW

dB is a standard abbreviation used for the quantitative expression of (a) the density of bacteria in a medium (b) a particular pollutant (c) the dominant Bacillus in a culture (d) a certain pesticide.

Description : dB is a standard abbreviation used for the quantitative expression of (a) the density of bacteria in a medium (b) a particular pollutant (c) the dominant Bacillus in a culture (d) a certain pesticide.

Last Answer : (b) a particular pollutant

Write down the name of communication channel used for telephone line and TV. -Technology

Description : Write down the name of communication channel used for telephone line and TV. -Technology

Last Answer : Communication channel for telephone line is twisted pair cable and for TV is co-axial cable.

Write down the name of communication channel used for telephone line and TV. -Technology

Description : Write down the name of communication channel used for telephone line and TV. -Technology

Last Answer : Communication channel for telephone line is twisted pair cable and for TV is co-axial cable.