The minimum clearance between the ground and a 220 kV line is about (a) 4.3 m (b) 5.5 m (c) 7.0 m (d) 10.5 m

The minimum clearance between the ground and a 220 kV line is about (a) 4.3 m (b) 5.5 m (c) 7.0 m (d) 10.5 m
by

1 Answer

Answer :

(c) 7.0 m
by

Related questions

The minimum clearance between the ground and a 220 kV line is about (a) 4.3 m (b) 5.5 m (c) 7.0 m (d) 10.5 m

Description : The minimum clearance between the ground and a 220 kV line is about (a) 4.3 m (b) 5.5 m (c) 7.0 m (d) 10.5 m

Last Answer : (c) 7.0 m

The operating voltage of extra high tension cables is upto (a) 6.6 kV (b) 11 kV (c) 33 kV (d) 66 kV (e) 132 kV

Description : The operating voltage of extra high tension cables is upto (a) 6.6 kV (b) 11 kV (c) 33 kV (d) 66 kV (e) 132 kV

Last Answer : (d) 66 kV

The operating voltage of supertension cables is up to (a) 3.3 kV (b) 6.6 kV (c) 11 kV (d) 33 kV

Description : The operating voltage of supertension cables is up to (a) 3.3 kV (b) 6.6 kV (c) 11 kV (d) 33 kV

Last Answer : (d) 33 kV

Overhead system can be designed for operation up to (a) 11 kV (b) 33 kV (c) 66 kV (d) 400 kV

Description : Overhead system can be designed for operation up to (a) 11 kV (b) 33 kV (c) 66 kV (d) 400 kV

Last Answer : (c) 66 kV

The underground system cannot be operated above (a) 440 V (b) 11 kV (c) 33 kV (d) 66 kV

Description : The underground system cannot be operated above (a) 440 V (b) 11 kV (c) 33 kV (d) 66 kV

Last Answer : (d) 66 kV

If variable part of annual cost on account of interest and depreciation on the capital outlay is equal to the annual cost of electrical energy wasted in the conductors, the total annual cost will be minimum and the corresponding size of conductor will be most economical. This statement is known as (a) Kelvin's law (b) Ohm's law (c) Kirchhoffs law (d) Faraday's law (e) none of the above

Description : If variable part of annual cost on account of interest and depreciation on the capital outlay is equal to the annual cost of electrical energy wasted in the conductors, the total annual cost will be minimum and the ... (b) Ohm's law (c) Kirchhoffs law (d) Faraday's law (e) none of the above

Last Answer : (a) Kelvin's law

Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at the line terminals (c) Possibility of better protection for the line due to possible use of higher terminal reactants (d) Improvement of power factor at times of moderate and heavy loads (e) Possibility of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Description : Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at ... of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Last Answer : (a) Increase of short-circuit current of the system

The square root of the ratio of line impedance and shunt admittance is called the (a) surge impedance of the line (b) conductance of the line (c) regulation of the line (d) none of the above

Description : The square root of the ratio of line impedance and shunt admittance is called the (a) surge impedance of the line (b) conductance of the line (c) regulation of the line (d) none of the above

Last Answer : (a) surge impedance of the line

The phenomenon qf rise in voltage at the receiving end of the open-circuited or lightly loaded line is called the (a) Seeback effect (b) Ferranti effect (c) Raman effect (d) none of the above

Description : The phenomenon qf rise in voltage at the receiving end of the open-circuited or lightly loaded line is called the (a) Seeback effect (b) Ferranti effect (c) Raman effect (d) none of the above

Last Answer : (b) Ferranti effect

310 km line is considered as (a) a long line (b) a medium line (c) a short line (d) any of the above

Description : 310 km line is considered as (a) a long line (b) a medium line (c) a short line (d) any of the above

Last Answer : (a) a long line

The wooden poles well impregnated with creosite oil or any preservative compound have life (a) from 2 to 5 years (b) 10 to 15 years (c) 25 to 30 years (d) 60 to 70 years

Description : The wooden poles well impregnated with creosite oil or any preservative compound have life (a) from 2 to 5 years (b) 10 to 15 years (c) 25 to 30 years (d) 60 to 70 years

Last Answer : (c) 25 to 30 years

The spacing between phase conductors of a 220 kV line is approximately equal to (a) 2 m (b) 3.5 m (c) 6 m (d) 8.5 m

Description : The spacing between phase conductors of a 220 kV line is approximately equal to (a) 2 m (b) 3.5 m (c) 6 m (d) 8.5 m

Last Answer : (c) 6 m

The material commonly used for sheaths of underground cables is (a) lead (b) rubber (c) copper (d) iron

Description : The material commonly used for sheaths of underground cables is (a) lead (b) rubber (c) copper (d) iron

Last Answer : (a) lead

The material generally used for armour of high voltage cables is (a) aluminium (b) steel (c) brass (d) copper

Description : The material generally used for armour of high voltage cables is (a) aluminium (b) steel (c) brass (d) copper

Last Answer : (b) steel

In transmission lines the crossarms are made of (a) copper (b) wood (c) R.C.C. (d) steel

Description : In transmission lines the crossarms are made of (a) copper (b) wood (c) R.C.C. (d) steel

Last Answer : (d) steel

Overhead lines generally use (a) copper conductors (b) all aluminium conductors (c) A.C.S.R. conductors (d) none of these

Description : Overhead lines generally use (a) copper conductors (b) all aluminium conductors (c) A.C.S.R. conductors (d) none of these

Last Answer : (c) A.C.S.R. conductors

The material commonly used for insulation in high voltage cables is (a) lead (b) paper (c) rubber (d) none of the above

Description : The material commonly used for insulation in high voltage cables is (a) lead (b) paper (c) rubber (d) none of the above

Last Answer : (b) paper

Distribution lines in India generally use (a) wooden poles (b) R.C.C. poles (c) steel towers (d) none of the above

Description : Distribution lines in India generally use (a) wooden poles (b) R.C.C. poles (c) steel towers (d) none of the above

Last Answer : (b) R.C.C. poles

Multicore cables generally use (a) square conductors (b) circular conductors (c) rectangular conductors (d) sector-shaped conductors (e) none of the above

Description : Multicore cables generally use (a) square conductors (b) circular conductors (c) rectangular conductors (d) sector-shaped conductors (e) none of the above

Last Answer : (d) sector-shaped conductors

High voltage transmission lines use (a) suspension insulators (b) pin insulators (c) both (a) and (b) (d) none of the above

Description : High voltage transmission lines use (a) suspension insulators (b) pin insulators (c) both (a) and (b) (d) none of the above

Last Answer : (a) suspension insulators

The distributors for residential areas are (a) single phase (b) three-phase three wire (c) three-phase four wire (d) none of the above

Description : The distributors for residential areas are (a) single phase (b) three-phase three wire (c) three-phase four wire (d) none of the above

Last Answer : (c) three-phase four wire

Most of the high voltage transmission lines in India are (a) underground (b) overhead (c) either of the above (d) none of the above

Description : Most of the high voltage transmission lines in India are (a) underground (b) overhead (c) either of the above (d) none of the above

Last Answer : (b) overhead

The voltage of the single phase supply to residential consumers is (a) 110 V (b) 210 V (c) 230 V (d) 400 V

Description : The voltage of the single phase supply to residential consumers is (a) 110 V (b) 210 V (c) 230 V (d) 400 V

Last Answer : (c) 230 V

Besides a method of trial and error, which of the following methods is employed for solution of network problems in interconnected system ? (a) Circulating current method (b) Thevenin's theorem (c) Superposition of currents (d) Direct application of Kirehhoffs laws (e) All of the above

Description : Besides a method of trial and error, which of the following methods is employed for solution of network problems in interconnected system ? (a) Circulating current method (b) Thevenin's theorem (c) Superposition of currents (d) Direct application of Kirehhoffs laws (e) All of the above

Last Answer : (e) All of the above

A booster is a (a) series wound generator (b) shunt wound generator (c) synchronous generator (d) none of the above

Description : A booster is a (a) series wound generator (b) shunt wound generator (c) synchronous generator (d) none of the above

Last Answer : (a) series wound generator

Which of the following D.C. distribution system is the simplest and lowest in first cost ? (a) Radial system (b) Ring system (c) Inter-connected system (d) None of the above

Description : Which of the following D.C. distribution system is the simplest and lowest in first cost ? (a) Radial system (b) Ring system (c) Inter-connected system (d) None of the above

Last Answer : (a) Radial system

Due to which of the following reasons the cables should not be operated too hot ? (a) The oil may loose its viscosity and it may start drawing off from higher levels (b) Expansion of the oil may cause the sheath to burst (c) Unequal expansion may create voids in the insulation which will lead to ionization (d) The thermal instability may rise due to the rapid increase of dielectric losses with temperature (e) All of the above

Description : Due to which of the following reasons the cables should not be operated too hot ? (a) The oil may loose its viscosity and it may start drawing off from higher levels (b) Expansion of the ... instability may rise due to the rapid increase of dielectric losses with temperature (e) All of the above

Last Answer : (e) All of the above

Which of the following methods is used for laying of underground cables ? (a) Direct laying (b) Draw-in-system (c) Solid system (d) All of the above

Description : Which of the following methods is used for laying of underground cables ? (a) Direct laying (b) Draw-in-system (c) Solid system (d) All of the above

Last Answer : (d) All of the above

The operating voltage of high voltage cables is up to (a)l.lkV (b)3.3kV (c)6.6kV (d)llkV

Description : The operating voltage of high voltage cables is up to (a)l.lkV (b)3.3kV (c)6.6kV (d)llkV

Last Answer : (d)llkV

Which of the following are the constants of the transmission lines ? (a) Resistance (b) Inductance (c) Capacitance (d) All of the above

Description : Which of the following are the constants of the transmission lines ? (a) Resistance (b) Inductance (c) Capacitance (d) All of the above

Last Answer : (d) All of the above

The corona is considerably affected by which of the following ? (a) Size of the conductor (b) Shape of the conductor (c) Surface condition of the conductor (d) All of the above

Description : The corona is considerably affected by which of the following ? (a) Size of the conductor (b) Shape of the conductor (c) Surface condition of the conductor (d) All of the above

Last Answer : (d) All of the above

The usual spans with R.C.C. poles are (a) 40—50 meters (b) 60—100 meters (c) 80—100 meters (d) 300—500 meters

Description : The usual spans with R.C.C. poles are (a) 40—50 meters (b) 60—100 meters (c) 80—100 meters (d) 300—500 meters

Last Answer : (c) 80—100 meters

Galvanised steel wire is generally used as (a) stay wire (b) earth wire (c) structural components (d) all of the above

Description : Galvanised steel wire is generally used as (a) stay wire (b) earth wire (c) structural components (d) all of the above

Last Answer : (d) all of the above

Which of the following materials is not used for transmission and distribution of electrical power ? (a) Copper (b) Aluminium (c) Steel (d) Tungsten

Description : Which of the following materials is not used for transmission and distribution of electrical power ? (a) Copper (b) Aluminium (c) Steel (d) Tungsten

Last Answer : (d) Tungsten

are the conductors, which connect the consumer's terminals to the distribution (a) Distributors (b) Service mains (c) Feeders (d) None of the above

Description : are the conductors, which connect the consumer's terminals to the distribution (a) Distributors (b) Service mains (c) Feeders (d) None of the above

Last Answer : (b) Service mains

By which of the following systems electric power may be transmitted ? (a) Overhead system (b) Underground system (c) Both (a) and (b) (d) None of the above

Description : By which of the following systems electric power may be transmitted ? (a) Overhead system (b) Underground system (c) Both (a) and (b) (d) None of the above

Last Answer : (c) Both (a) and (b)

The X:R ratio of 220 kV line as compared to 400 kV line is?

Description : The X:R ratio of 220 kV line as compared to 400 kV line is?

Last Answer : The X:R ratio of 220 kV line as compared to 400 kV line is smaller.

A minimum clearance of 6.3 m to ground is required for overhead lines when operating voltages are :

Description : A minimum clearance of 6.3 m to ground is required for overhead lines when operating voltages are :  (A) less than 66 kV (B) lie between 66 kV and 110 kV (C) more than 165 kV (D) lie between 110 kV and 165 kV

Last Answer : A minimum clearance of 6.3 m to ground is required for overhead lines when operating voltages are : lie between 66 kV and 110 kV

What are the levels of SF6 gas in 220 kV breaker and their significance?

Description : What are the levels of SF6 gas in 220 kV breaker and their significance?

Last Answer : 7 kg/cm2 - normal pressure 5.2 bar - alarm 5.0 bar - closing/tripping operation blocked. 

What is the type of 220 kV circuit breaker?

Description : What is the type of 220 kV circuit breaker? 

Last Answer : 220 kV, SF6 breaker, single pole, puffer type. 

What are the main parts of 220 kV Circuit Breaker?

Description : What are the main parts of 220 kV Circuit Breaker? 

Last Answer : Pole column filled with SF6 Pneumatic drive system with compressed air circuit Control cubicle unit 

Give the details of switchyard 220 kV CB, Isolator, CT, CVT and lightning arrestor.

Description : Give the details of switchyard 220 kV CB, Isolator, CT, CVT and lightning arrestor.  

Last Answer : 220 kV SF6 Circuit Breaker 1. Make - ABB 2. Air pressure blocking a. Close Block - 17.3 bar. b. Open block - 16.7 bar. c. Auto reclose block - 19 bar. 3. SF6 pressure block a. Alarm - 5. ... , storage and erection. Rated voltage : 216 kV rms. Operating voltage : 184 kV rms. 

In 220 kV switchyard why lightning arrestor should be properly grounded?

Description : In 220 kV switchyard why lightning arrestor should be properly grounded?

Last Answer : a. During lightning, surges should be discharged to ground, otherwise it will puncture the equipment insulation and it is possible only when lightning arrestor is grounded properly.  b. In order to make it effective ... kV. Soil resistivity a should be minimum and may be it is 3.5 ohm per meter.  

What is the difference in action of lock out pressure signal on 6.6 kV and 220 kV breakers?

Description : What is the difference in action of lock out pressure signal on 6.6 kV and 220 kV breakers?

Last Answer : When lock out signal comes to 6.6 kV breakers the breaker will trip. Where as in case of 220 kV breakers the breaker will not trip. If the breaker is open it will be open only and can not be closed. If it is in closed condition it will be closed.

What are the protections provided for 220 kV lines and bus bars?

Description : What are the protections provided for 220 kV lines and bus bars? 

Last Answer : a. Bus bar differential protection. b. Distance protection. c. Over current protection. d. Earth fault protection. 

Why earth switches are provided in 220 kV bays?

Description : Why earth switches are provided in 220 kV bays?  

Last Answer : When bay CB trips, both end (station and grid) CB will trip. The earth switches are provided because the grid will always be alive so to prevent any shocks to the operator or maintenance personnel who is working on the line or bay due to accidental energizing of the bus.  

Cables for 220 kV lines are invariably (a) mica insulated (b) paper insulated (c) compressed oil or compressed gas insulated (d) rubber insulated (e) none of the above

Description : Cables for 220 kV lines are invariably (a) mica insulated (b) paper insulated (c) compressed oil or compressed gas insulated (d) rubber insulated (e) none of the above

Last Answer : (c) compressed oil or compressed gas insulated

For transmission of power over a distance of 500 km, the transmission voltage should be in the range (a) 150 to 220 kV (b) 100 to 120 kV (c) 60 to 100 kV (d) 20 to 50 kV

Description : For transmission of power over a distance of 500 km, the transmission voltage should be in the range (a) 150 to 220 kV (b) 100 to 120 kV (c) 60 to 100 kV (d) 20 to 50 kV

Last Answer : (a) 150 to 220 kV

A single core cable is designed to work for a single phase system with a peak voltage of 220 kV. The maximum

Description : A single core cable is designed to work for a single phase system with a peak voltage of 220 kV. The maximum permissible stress in the dielectric is not to exceed 20 kV/mm. For economical size, the overall core diameter of the cable is (A) 28.2 mm (B) 26.4 mm (C) 24.4 mm (D) 22.0 mm

Last Answer : A single core cable is designed to work for a single phase system with a peak voltage of 220 kV. The maximum permissible stress in the dielectric is not to exceed 20 kV/mm. For economical size, the overall core diameter of the cable is 22.0 mm

The minimum vertical clearance of overhanging cliffs or any other structure above the surface of a hill road, should be (A) 3 m(B) 4 m (C) 5 m (D) 6 m

Description : The minimum vertical clearance of overhanging cliffs or any other structure above the surface of a hill road, should be (A) 3 m (B) 4 m (C) 5 m (D) 6 m

Last Answer : Answer: Option C