Which one of the following is the correct ratio of plastic moment to yield moment for a simply supported beam of uniform square cross section throughout the span (a) 1.5 (b) 1.7 (c) 2.0 (d) 2.34

Which one of the following is the correct ratio of plastic moment to yield moment
for a simply supported beam of uniform square cross section throughout the span
(a) 1.5 (b) 1.7 (c) 2.0 (d) 2.34
by

1 Answer

Answer :

(a) 1.5
by

Related questions

What is the distance away from midspan of a plastic hinge if developing in a simply supported beam of rectangular cross-section and span 6 m, subjected to a point load at the centre? (a) Zero (b) 1 m (c) 2 m (d) 3 m

Description : What is the distance away from midspan of a plastic hinge if developing in a simply supported beam of rectangular cross-section and span 6 m, subjected to a point load at the centre? (a) Zero (b) 1 m (c) 2 m (d) 3 m

Last Answer : (a) Zero

In case of a simply supported I-section beam of span L and loaded with a central load W, the length of elasto-plastic zone of the plastic hinge, is (A) L/2 (B) L/3 (C) L/4 (D) L/5

Description : In case of a simply supported I-section beam of span L and loaded with a central load W, the  length of elasto-plastic zone of the plastic hinge, is  (A) L/2  (B) L/3  (C) L/4  (D) L/5 

Last Answer : (D) L/5 

The ratio of the length and diameter of a simply supported uniform circular beam which experiences maximum bending stress equal to tensile stress due to same load at its mid span, is (A) 1/8 (B) 1/4 (C) 1/2 (D) 1/3

Description : The ratio of the length and diameter of a simply supported uniform circular beam which  experiences maximum bending stress equal to tensile stress due to same load at its mid span, is  (A) 1/8  (B) 1/4  (C) 1/2  (D) 1/3 

Last Answer : (C) 1/2 

A beam of uniform rectangular section 200 mm wide and 300mm deep is simply supported at its ends.It carries a uniformly distributed load of 9KN/m run over the entire span of 5m.If E=1×104 N/mm2, what is the maximum deflection? a.14.26 mm b.17.28 mm c.18.53 mm d.16.27 mm.

Description : A beam of uniform rectangular section 200 mm wide and 300mm deep is simply supported at its ends.It carries a uniformly distributed load of 9KN/m run over the entire span of 5m.If E=1×104 N/mm2, what is the maximum deflection? a.14.26 mm b.17.28 mm c.18.53 mm d.16.27 mm.

Last Answer : d.16.27 mm.

In case of a simply supported rectangular beam of span L and loaded with a central load W, the length of elasto-plastic zone of the plastic hinge, is (A) L/2 (B) L/3 (C) L/4 (D) L/5

Description : In case of a simply supported rectangular beam of span L and loaded with a central load W, the  length of elasto-plastic zone of the plastic hinge, is  (A) L/2  (B) L/3  (C) L/4  (D) L/5 

Last Answer : (B) L/3 

Basic value of span to depth ratio for simply supported beam to control deflection is [ A ] 7 [ B ] 20 [ C ] 26 [ D ] 35

Description : Basic value of span to depth ratio for simply supported beam to control deflection is [ A ] 7 [ B ] 20 [ C ] 26 [ D ] 35

Last Answer : [ B ] 20

A simply supported beam of span carries a uniformly distributed load . The maximum bending moment is (A) WL/2 (B) WL/4 (C) WL/8 (D) WL/12

Description : A simply supported beam of span carries a uniformly distributed load . The maximum bending moment is (A) WL/2 (B) WL/4 (C) WL/8 (D) WL/12

Last Answer : (C) WL/8

A simply supported beam of span L carries a concentrated load W at its mid-span. The maximum bending moment M is (A) WL/2 (B) WL/4 (C) WL/8 (D) WL/12

Description : A simply supported beam of span L carries a concentrated load W at its mid-span. The maximum  bending moment M is  (A) WL/2  (B) WL/4  (C) WL/8  (D) WL/12

Last Answer : (B) WL/4

The maximum bending moment due to a moving load on a simply supported beam, occurs (A) At the mid span (B) At the supports (C) Under the load (D) Anywhere on the beam

Description : The maximum bending moment due to a moving load on a simply supported beam, occurs (A) At the mid span (B) At the supports (C) Under the load (D) Anywhere on the beam

Last Answer : (C) Under the load

The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of 4 tonnes at the centre. The maximum stress in the bottom most fibre at the mid span section, is (A) 13.33 kg/cm2 tensile (B) 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive

Description : The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of ... 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive

Last Answer : (C) 26.67 kg/cm2 tensile

A simply supported uniform rectangular bar breadth b, depth d and length L carries an isolated load W at its mid-span. The same bar experiences an extension e under same tensile load. The ratio of the maximum deflection to the elongation, is (A) L/d (B) L/2d (C) (L/2d)² (D) (L/3d)²

Description : A simply supported uniform rectangular bar breadth b, depth d and length L carries an isolated  load W at its mid-span. The same bar experiences an extension e under same tensile load. The  ratio of the maximum deflection to the ... (A) L/d (B) L/2d (C) (L/2d)² (D) (L/3d)²

Last Answer : (C) (L/2d)

A simply supported beam A carries a point load at its mid span. Another identical beam B carries the same load but uniformly distributed over the entire span. The ratio of the maximum deflections of the beams A and B, will be (A) 2/3 (B) 3/2 (C) 5/8 (D) 8/5

Description : A simply supported beam A carries a point load at its mid span. Another identical beam B carries  the same load but uniformly distributed over the entire span. The ratio of the maximum  deflections of the beams A and B, will be  (A) 2/3  (B) 3/2  (C) 5/8  (D) 8/5 

Last Answer : (D) 8/5 

The ratio of the length and depth of a simply supported rectangular beam which experiences maximum bending stress equal to tensile stress, due to same load at its mid span, is (A) 1/2 (B) 2/3 (C) 1/4 (D) 1/3

Description : The ratio of the length and depth of a simply supported rectangular beam which experiences  maximum bending stress equal to tensile stress, due to same load at its mid span, is  (A) 1/2  (B) 2/3  (C) 1/4  (D) 1/3

Last Answer : (B) 2/3 

For the design of a simply supported T-beam the ratio of the effective span to the overall depth of the beam is limited to (A) 10 (B) 15 (C) 20 (D) 25

Description : For the design of a simply supported T-beam the ratio of the effective span to the overall depth of the beam is limited to (A) 10 (B) 15 (C) 20 (D) 25

Last Answer : Answer: Option C

For normal cases, stiffness of a simply supported beam is satisfied if the ratio of its span to its overall depth does not exceed (A) 10 (B) 15 (C) 20 (D) 25

Description : For normal cases, stiffness of a simply supported beam is satisfied if the ratio of its span to its overall depth does not exceed (A) 10 (B) 15 (C) 20 (D) 25

Last Answer : Answer: Option C

If the ratio of the span to the overall depth does not exceed 10, the stiffness of the beam will ordinarily be satisfactory in case of a (A) Simply supported beam (B) Continuous beam (C) Cantilever beam (D) None of these

Description : If the ratio of the span to the overall depth does not exceed 10, the stiffness of the beam will ordinarily be satisfactory in case of a (A) Simply supported beam (B) Continuous beam (C) Cantilever beam (D) None of these

Last Answer : Answer: Option C

A beam of uniform strength has a. same cross-section throughout the beam b. same bending stress at every section c. same bending moment at every section d. same shear stress at every section

Description : A beam of uniform strength has a. same cross-section throughout the beam b. same bending stress at every section c. same bending moment at every section d. same shear stress at every section

Last Answer : b. same bending stress at every section

In comparison with a simply supported beam of same span and load , a continuous beam has a.less maximum bending moment b. same bending moment c. higher maximum bending moment d. twice the bending moment

Description : In comparison with a simply supported beam of same span and load , a continuous beam has a.less maximum bending moment b. same bending moment c. higher maximum bending moment d. twice the bending moment

Last Answer : a.less maximum bending moment

For the same span and loads fixed beam in comparison with simply supported beams has a. lesser value of maximum bending moment b. more value of maximum bending moment c.twice the value of maximum bending moment d.same value of maximum bending moment

Description : For the same span and loads fixed beam in comparison with simply supported beams has a. lesser value of maximum bending moment b. more value of maximum bending moment c.twice the value of maximum bending moment d.same value of maximum bending moment

Last Answer : a. lesser value of maximum bending moment

A concentrated load P acts on a simply supported beam of span L at a distance L/3 from the left support. The bending moment at the point of application of the load is given by (a) PL/3 (b) 2PL/3 (c) PL/9 (d) 2PL/9

Description : A concentrated load P acts on a simply supported beam of span L at a distance L/3 from the left support. The bending moment at the point of application of the load is given by (a) PL/3 (b) 2PL/3 (c) PL/9 (d) 2PL/9

Last Answer : (d) 2PL/9

A simply supported beam is of rectangular section.It carries a uniformly distributed load over the whole span.The deflection at the centre is y.If the depth of beam is doubled ,the deflection at the centre would be a.2y b.4y c.y/2 d.y/8.

Description : A simply supported beam is of rectangular section.It carries a uniformly distributed load over the whole span.The deflection at the centre is y.If the depth of beam is doubled ,the deflection at the centre would be a.2y b.4y c.y/2 d.y/8.

Last Answer : d.y/8.

Pick up the correct statement from the following: (A) In a loaded beam, the moment at which the first yield occurs is called yield moment(B) In a loaded beam, the moment at which the entire section of the beam becomes fully plastic, is called plastic moment (C) In a fully plastic stage of the beam, the neutral axis divides the section in two sections of equal area (D) All the above

Description : Pick up the correct statement from the following:  (A) In a loaded beam, the moment at which the first yield occurs is called yield moment (B) In a loaded beam, the moment at which the ... beam, the neutral axis divides the section in two sections of  equal area  (D) All the above 

Last Answer : (D) All the above 

A simply supported wooden beam 150 cm long and having a cross section 16 cm × 24 cm carries a concentrated load, at the centre. If the permissible stress ft = 75 kg/cm2 and fs= 10 kg/cm2 the safe load is (A) 3025 kg (B) 3050 kg (C) 3075 kg (D) 3100 kg

Description : A simply supported wooden beam 150 cm long and having a cross section 16 cm × 24 cm carries a  concentrated load, at the centre. If the permissible stress ft = 75 kg/cm2  and fs= 10 kg/cm2  the safe  load is  (A) 3025 kg  (B) 3050 kg  (C) 3075 kg  (D) 3100 kg 

Last Answer : (C) 3075 kg 

If a constant section beam is subjected to a uniform bending moment throughout, its length bends to (A) A circular arc (B) A parabolic arc (C) A catenary (D) None of these

Description : If a constant section beam is subjected to a uniform bending moment throughout, its length bends  to  (A) A circular arc  (B) A parabolic arc  (C) A catenary  (D) None of these 

Last Answer : (A) A circular arc 

Negative yield line form i. Near the supports in the case of slabs fixed or continuous at the edge. ii. At mid span in the case of slabs fixed. iii.At mid span for simply supported circular slab [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Description : Negative yield line form i. Near the supports in the case of slabs fixed or continuous at the edge. ii. At mid span in the case of slabs fixed. iii.At mid span for simply supported circular slab [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Last Answer : [ A ] i

A simply supported beam carrying a uniformly distributed load over its whole span, is propped at the centre of the span so that the beam is held to the level of the end supports. The reaction of the prop will be (A) Half the distributed load (B) 3/8th the distributed load (C) 5/8th the distributed load (D) Distributed load

Description : A simply supported beam carrying a uniformly distributed load over its whole span, is propped at  the centre of the span so that the beam is held to the level of the end supports. The reaction of  ... B) 3/8th the distributed load  (C) 5/8th the distributed load  (D) Distributed load 

Last Answer : (C) 5/8th the distributed load 

The maximum deflection of a simply supported beam of span L, carrying an isolated load at the centre of the span; flexural rigidity being EI, is (A) WL3 /3EL (B) WL3 /8EL (C) WL3 /24EL (D) WL3 /48EL

Description : The maximum deflection of a simply supported beam of span L, carrying an isolated load at the  centre of the span; flexural rigidity being EI, is  (A) WL3 /3EL (B) WL3 /8EL (C) WL3 /24EL (D) WL3 /48EL

Last Answer : (D) WL3 /48EL

The maximum deflection of (A) A simply supported beam carrying a uniformly increasing load from either end and having the apex at the mid span is WL3 /60EI (B) A fixed ended beam carrying a distributed load over the span is WL3 /384EI (C) A fixed ended beam carrying a concentrated load at the mid span is WL3 /192EI (D) All the above

Description : The maximum deflection of  (A) A simply supported beam carrying a uniformly increasing load from either end and having  the apex at the mid span is WL3 /60EI (B) A fixed ended beam ... ended beam carrying a concentrated load at the mid span is WL3 /192EI (D) All the above 

Last Answer : (D) All the above 

Maximum deflection of a (A) Cantilever beam carrying a concentrated load W at its free end is WL3 /3EI (B) Simply supported beam carrying a concentrated load W at mid-span is WL3 /48EI (C) Cantilever beam, carrying a uniformly distributed load over span is WL3 /8EI (D) All the above

Description : Maximum deflection of a (A) Cantilever beam carrying a concentrated load W at its free end is WL3 /3EI (B) Simply supported beam carrying a concentrated load W at mid-span is WL3 /48EI (C) Cantilever beam, carrying a uniformly distributed load over span is WL3 /8EI (D) All the above

Last Answer : (D) All the above

If the maximum shear stress at the end of a simply supported R.C.C. beam of 6 m effective span is 10 kg/cm2 , the share stirrups are provided for a distance from either end where, is (A) 50 cm (B) 100 cm(C) 150 cm (D) 200 cm

Description : If the maximum shear stress at the end of a simply supported R.C.C. beam of 6 m effective span is 10 kg/cm2 , the share stirrups are provided for a distance from either end where, is (A) 50 cm (B) 100 cm (C) 150 cm (D) 200 cm

Last Answer : Answer: Option C

If the maximum shear stress at the end of a simply supported R.C.C. beam of 16 m effective span is 10 kg/cm2 , the length of the beam having nominal reinforcement, is (A) 8 cm (B) 6 m (C) 8 m (D) 10 m

Description : If the maximum shear stress at the end of a simply supported R.C.C. beam of 16 m effective span is 10 kg/cm2 , the length of the beam having nominal reinforcement, is (A) 8 cm (B) 6 m (C) 8 m (D) 10 m

Last Answer : Answer: Option C

For a simply supported beam of span 15 m, the minimum effective depth to satisfy the vertical deflection limits should be (A) 600 mm (B) 750 mm (C) 900 mm (D) More than 1 m

Description : For a simply supported beam of span 15 m, the minimum effective depth to satisfy the vertical deflection limits should be (A) 600 mm (B) 750 mm (C) 900 mm (D) More than 1 m

Last Answer : Answer: Option B

A simply supported beam AB is subjected to a concentrated load at C, the centre of the span. The area of the SF diagram from A to C will give a) BM at C b) Load at S c) SF at C d)Difference between BM values at A and C

Description : A simply supported beam AB is subjected to a concentrated load at C, the centre of the span. The area of the SF diagram from A to C will give a) BM at C b) Load at S c) SF at C d)Difference between BM values at A and C

Last Answer : d)Difference between BM values at A and C

A continuous beam is simply supported on its one or both the end supports the fixing moment on simply supported beam end is a. zero b. infinite c. neglected in calculation d. multiplied by a cross over factor in calculation

Description : A continuous beam is simply supported on its one or both the end supports the fixing moment on simply supported beam end is a. zero b. infinite c. neglected in calculation d. multiplied by a cross over factor in calculation

Last Answer : a. zero

When a series of wheel loads crosses a simply supported girder, the maximum bending moment under any given wheel load occurs when (A) The centre of gravity of the load system is midway between the centre of span and wheel load under consideration (B) The centre of span is midway between the centre of gravity of the load system and the wheel load under consideration (C) The wheel load under consideration is midway between the centre of span and the centre of gravity of the load system (D) None of the above

Description : When a series of wheel loads crosses a simply supported girder, the maximum bending moment under any given wheel load occurs when (A) The centre of gravity of the load system is midway between the centre of ... the centre of span and the centre of gravity of the load system (D) None of the above

Last Answer : (B) The centre of span is midway between the centre of gravity of the load system and the wheel load under consideration

The maximum bending moment due to a train of wheel loads on a simply supported girder (A) Always occurs at centre of span (B) Always occurs under a wheel load (C) Never occurs under a wheel load (D) None of the above

Description : The maximum bending moment due to a train of wheel loads on a simply supported girder (A) Always occurs at centre of span (B) Always occurs under a wheel load (C) Never occurs under a wheel load (D) None of the above

Last Answer : (B) Always occurs under a wheel load

A uniformly distributed load of 20 kN/m acts on a simply supported beam of rectangular cross section of width 20 mm and depth 60 mm. What is the maximum bending stress acting on the beam of 5m? a. 5030 Mpa b. 5208 Mpa c. 6600 Mpa d. Insufficient data

Description : A uniformly distributed load of 20 kN/m acts on a simply supported beam of rectangular cross section of width 20 mm and depth 60 mm. What is the maximum bending stress acting on the beam of 5m? a. 5030 Mpa b. 5208 Mpa c. 6600 Mpa d. Insufficient data

Last Answer : b. 5208 Mpa

The width of a beam of uniform strength having a constant depth d length L, simply supported at the ends with a central load W is (A) 2WL/3fd² (B) 3WL/2fd² (C) 2fL/3Wd 4 (D) 3fL²/2Wd

Description : The width of a beam of uniform strength having a constant depth d length L, simply supported at the ends with a central load W is (A) 2WL/3fd² (B) 3WL/2fd² (C) 2fL/3Wd 4 (D) 3fL²/2Wd

Last Answer : (B) 3WL/2fd²

Design of R.C.C. simply supported beams carrying U.D.L. is based on the resultant B.M. at (A) Supports (B) Mid span (C) Every section (D) Quarter span

Description : Design of R.C.C. simply supported beams carrying U.D.L. is based on the resultant B.M. at (A) Supports (B) Mid span (C) Every section (D) Quarter span

Last Answer : Answer: Option B

The maximum bending moment for a simply supported beam with a uniformly distributed load w/unit length, is (A) WI/2 (B) WI²/4 (C) WI²/8 (D) WI²/12

Description : The maximum bending moment for a simply supported beam with a uniformly distributed  load w/unit length, is  (A) WI/2  (B) WI²/4  (C) WI²/8  (D) WI²/12

Last Answer : (C) WI²/8 

A simply supported beam carries two equal concentrated loads W at distances L/3 from either support. The maximum bending moment (A) WL/3 (B) WL/4 (C) 5WL/4 (D) 3WL/12

Description : A simply supported beam carries two equal concentrated loads W at distances L/3 from either support. The maximum bending moment (A) WL/3 (B) WL/4 (C) 5WL/4 (D) 3WL/12

Last Answer : (A) WL/3

For a simply supported beam carrying uniformly distributed load W on it entire length L, the maximum bending moment is (A) WL/4 (B) WL/8 (C) WL/2 (D) WL/3

Description : For a simply supported beam carrying uniformly distributed load W on it entire length L, the maximum bending moment is (A) WL/4 (B) WL/8 (C) WL/2 (D) WL/3

Last Answer : (B) WL/8

For a simply supported beam with a central load, the bending moment is (A) Least at the centre (B) Least at the supports (C) Maximum at the supports (D) Maximum at the centre

Description : For a simply supported beam with a central load, the bending moment is  (A) Least at the centre  (B) Least at the supports  (C) Maximum at the supports  (D) Maximum at the centre

Last Answer : (D) Maximum at the centre

A 8 metre long simply supported rectangular beam which carries a distributed load 45 kg/m. experiences a maximum fibre stress 160 kg/cm2 . If the moment of inertia of the beam is 640 cm4 , the overall depth of the beam is (A) 10 cm (B) 12 cm (C) 15 cm (D) 18 cm

Description : A 8 metre long simply supported rectangular beam which carries a distributed load 45 kg/m. experiences a maximum fibre stress 160 kg/cm2 . If the moment of inertia of the beam is 640 cm4 , the overall depth of the beam is (A) 10 cm (B) 12 cm (C) 15 cm (D) 18 cm

Last Answer : (A) 10 cm

While testing a cast iron beam (2.5 cm × 2.5 cm) in section and a metre long simply supported at the ends failed when a 100 kg weight is applied at the centre. The maximum stress induced is: (A) 960 kg/cm2 (B) 980 kg/cm2 (C) 1000 kg/cm2 (D) 1200 kg/cm2 Answer: Option

Description : While testing a cast iron beam (2.5 cm × 2.5 cm) in section and a metre long simply supported at  the ends failed when a 100 kg weight is applied at the centre. The maximum stress induced is:  (A) 960 kg/cm2 (B) 980 kg/cm2 (C) 1000 kg/cm2 (D) 1200 kg/c

Last Answer : (A) 960 kg/cm

The shear force on a simply supported beam is proportional to (A) Displacement of the neutral axis (B) Sum of the forces (C) Sum of the transverse forces (D) Algebraic sum of the transverse forces of the section

Description : The shear force on a simply supported beam is proportional to (A) Displacement of the neutral axis (B) Sum of the forces (C) Sum of the transverse forces (D) Algebraic sum of the transverse forces of the section

Last Answer : (D) Algebraic sum of the transverse forces of the section

For the same span and loads fixed beam in comparison with simply supported beams has a. lesser value of maximum deflection b. more value of maximum deflecction c.twice the value of maximum deflecction d.same value of maximum deflecction

Description : For the same span and loads fixed beam in comparison with simply supported beams has a. lesser value of maximum deflection b. more value of maximum deflecction c.twice the value of maximum deflecction d.same value of maximum deflecction

Last Answer : a. lesser value of maximum deflection

A simply supported beam carries a uniformly distributed load over the whole span.The deflection at the centre is y.If the distributed load per unit length is doubled and also depth of beam is doubled ,then the deflection at the centre would be a.2y b.4y c.y/2 d.y/4.

Description : A simply supported beam carries a uniformly distributed load over the whole span.The deflection at the centre is y.If the distributed load per unit length is doubled and also depth of beam is doubled ,then the deflection at the centre would be a.2y b.4y c.y/2 d.y/4.

Last Answer : d.y/4.

In a simply supported beam carrying a uniformly distributed load over the left half span, the point of contraflexure will occur in (a) Left half span of the beam (b) Right half span of the beam. (c) Quarter points of the beam (d) Does not exist

Description : In a simply supported beam carrying a uniformly distributed load over the left half span, the point of contraflexure will occur in (a) Left half span of the beam (b) Right half span of the beam. (c) Quarter points of the beam (d) Does not exist

Last Answer : (d) Does not exist

The shear force at the centre of a simply supported beam of span l carrying a uniformly distributed load of w per unit length over the whole span is (a) wl (b) wl/2 (c) wl/4 (d) Zero

Description : The shear force at the centre of a simply supported beam of span l carrying a uniformly distributed load of w per unit length over the whole span is (a) wl (b) wl/2 (c) wl/4 (d) Zero

Last Answer : (d) Zero