A simply supported beam of span L carries a concentrated load W at its mid-span. The maximum
bending moment M is
(A) WL/2
(B) WL/4
(C) WL/8
(D) WL/12
Description : A simply supported beam carries two equal concentrated loads W at distances L/3 from either support. The maximum bending moment (A) WL/3 (B) WL/4 (C) 5WL/4 (D) 3WL/12
Last Answer : (A) WL/3
Description : A simply supported beam of span carries a uniformly distributed load . The maximum bending moment is (A) WL/2 (B) WL/4 (C) WL/8 (D) WL/12
Last Answer : (C) WL/8
Description : In a simply supported beam subjected to uniformly distributed load (w) over the entire length (l), total load=W, maximum Bending moment is (a) Wl/8 or wl2/8 at the mid-point (b) Wl/8 or wl2/8 at the end (c) Wl/4 or wl2/4 (d) Wl/2
Last Answer : (a) Wl/8 or wl2/8 at the mid-point
Description : For a simply supported beam carrying uniformly distributed load W on it entire length L, the maximum bending moment is (A) WL/4 (B) WL/8 (C) WL/2 (D) WL/3
Last Answer : (B) WL/8
Description : For a simply supported beam of span L, with point load W at the centre, the maximum B.M. will be (a) WL (b) WL/2 (c) WL/4 (d) WL/8
Last Answer : (c) WL/4
Description : The general expression for the B.M. of a beam of length l is the beam carries M = (wl/2) x - (wx²/2) (A) A uniformly distributed load w/unit length (B) A load varying linearly from zero at one end to w at the other end (C) An isolated load at mid span (D) None of these
Last Answer : (A) A uniformly distributed load w/unit length
Description : A concentrated load P acts on a simply supported beam of span L at a distance L/3 from the left support. The bending moment at the point of application of the load is given by (a) PL/3 (b) 2PL/3 (c) PL/9 (d) 2PL/9
Last Answer : (d) 2PL/9
Description : The maximum bending moment due to a moving load on a simply supported beam, occurs (A) At the mid span (B) At the supports (C) Under the load (D) Anywhere on the beam
Last Answer : (C) Under the load
Description : For a simply supported beam of span L, loaded with U.D.L. w/m over the whole span, the maximum B.M will be (a) wL/4 (b) wL2 /8 (c) wL2 /4 (d) WwL2 /2
Last Answer : (b) wL2
Description : Maximum deflection of a (A) Cantilever beam carrying a concentrated load W at its free end is WL3 /3EI (B) Simply supported beam carrying a concentrated load W at mid-span is WL3 /48EI (C) Cantilever beam, carrying a uniformly distributed load over span is WL3 /8EI (D) All the above
Last Answer : (D) All the above
Description : The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of ... 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive
Last Answer : (C) 26.67 kg/cm2 tensile
Description : A simply supported uniform rectangular bar breadth b, depth d and length L carries an isolated load W at its mid-span. The same bar experiences an extension e under same tensile load. The ratio of the maximum deflection to the ... (A) L/d (B) L/2d (C) (L/2d)² (D) (L/3d)²
Last Answer : (C) (L/2d)
Description : A simply supported beam A carries a point load at its mid span. Another identical beam B carries the same load but uniformly distributed over the entire span. The ratio of the maximum deflections of the beams A and B, will be (A) 2/3 (B) 3/2 (C) 5/8 (D) 8/5
Last Answer : (D) 8/5
Description : The ratio of the length and diameter of a simply supported uniform circular beam which experiences maximum bending stress equal to tensile stress due to same load at its mid span, is (A) 1/8 (B) 1/4 (C) 1/2 (D) 1/3
Last Answer : (C) 1/2
Description : If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span ... (L + 2D/3)² (C) WL/10 (L - 2D/3)² (D) WL/12 (L - D/3)²
Last Answer : Answer: Option C
Description : The shear force at the centre of a simply supported beam of span l carrying a uniformly distributed load of w per unit length over the whole span is (a) wl (b) wl/2 (c) wl/4 (d) Zero
Last Answer : (d) Zero
Description : The maximum deflection of (A) A simply supported beam carrying a uniformly increasing load from either end and having the apex at the mid span is WL3 /60EI (B) A fixed ended beam ... ended beam carrying a concentrated load at the mid span is WL3 /192EI (D) All the above
Description : The ratio of the length and depth of a simply supported rectangular beam which experiences maximum bending stress equal to tensile stress, due to same load at its mid span, is (A) 1/2 (B) 2/3 (C) 1/4 (D) 1/3
Last Answer : (B) 2/3
Description : If the length of a wall on either side of a lintel opening is at least half of its effective span L, the load W carried by the lintel is equivalent to the weight of brickwork contained in an equilateral triangle, producing a maximum bending moment (A) WL/2 (B) WL/4 (C) WL/6 (D) WL/8
Description : A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the value of E = 0.2 ... joist, is (A) 200 mm (B) 250 mm (C) 300 mm (D) 400 mm
Last Answer : (D) 400 mm
Description : A 8 metre long simply supported rectangular beam which carries a distributed load 45 kg/m. experiences a maximum fibre stress 160 kg/cm2 . If the moment of inertia of the beam is 640 cm4 , the overall depth of the beam is (A) 10 cm (B) 12 cm (C) 15 cm (D) 18 cm
Last Answer : (A) 10 cm
Description : The maximum bending moment for a simply supported beam with a uniformly distributed load w/unit length, is (A) WI/2 (B) WI²/4 (C) WI²/8 (D) WI²/12
Last Answer : (C) WI²/8
Description : A pre-stressed rectangular beam which carries two concentrated loads W at L/3 from either end, is provided with a bent tendon with tension P such that central one-third portion of the tendon remains parallel to the longitudinal axis, the maximum dip h is (A) WL/P (B) WL/2P (C) WL/3P (D) WL/4P
Description : In comparison with a simply supported beam of same span and load , a continuous beam has a.less maximum bending moment b. same bending moment c. higher maximum bending moment d. twice the bending moment
Last Answer : a.less maximum bending moment
Description : A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending strain energy stored in the ... (A) 411 N mm (B) 511 N mm (C) 611 N mm (D) 711 N mm
Last Answer : (C) 611 N mm
Description : In a cantilever subjected to a concentrated load (W) at the free end and having length =l, Maximum bending moment is (a) Wl at the free end (b) Wl at the fixed end (c) Wl/2 at the fixed end (d) Wl at the free end
Last Answer : (b) Wl at the fixed end
Description : A beam of uniform rectangular section 200 mm wide and 300mm deep is simply supported at its ends.It carries a uniformly distributed load of 9KN/m run over the entire span of 5m.If E=1×104 N/mm2, what is the maximum deflection? a.14.26 mm b.17.28 mm c.18.53 mm d.16.27 mm.
Last Answer : d.16.27 mm.
Description : Maximum bending moment in a S.S. beam having a concentrated load at the centre will be (a) WL (b) WL/2 (c) WL/4 (d) None
Description : In a simply supported beam, bending moment at the end (a) Is always zero if it does not carry couple at the end (b) Is zero, if the beam has uniformly distributed load only (c) Is zero if the beam has concentrated loads only (d) May or may not be zero
Last Answer : (a) Is always zero if it does not carry couple at the end
Description : When a series of wheel loads crosses a simply supported girder, the maximum bending moment under any given wheel load occurs when (A) The centre of gravity of the load system is midway between the centre of ... the centre of span and the centre of gravity of the load system (D) None of the above
Last Answer : (B) The centre of span is midway between the centre of gravity of the load system and the wheel load under consideration
Description : The maximum bending moment due to a train of wheel loads on a simply supported girder (A) Always occurs at centre of span (B) Always occurs under a wheel load (C) Never occurs under a wheel load (D) None of the above
Last Answer : (B) Always occurs under a wheel load
Description : For the same span and loads fixed beam in comparison with simply supported beams has a. lesser value of maximum bending moment b. more value of maximum bending moment c.twice the value of maximum bending moment d.same value of maximum bending moment
Last Answer : a. lesser value of maximum bending moment
Description : A simply supported wooden beam 150 cm long and having a cross section 16 cm × 24 cm carries a concentrated load, at the centre. If the permissible stress ft = 75 kg/cm2 and fs= 10 kg/cm2 the safe load is (A) 3025 kg (B) 3050 kg (C) 3075 kg (D) 3100 kg
Last Answer : (C) 3075 kg
Description : A simply supported beam (l + 2a) with equal overhangs (a) carries a uniformly distributed load over the whole length, the B.M. changes sign if (A) l > 2a (B) l < 2a (C) l = 2a (D) l = 4a
Last Answer : (A) l > 2a
Description : In case of a simply supported rectangular beam of span L and loaded with a central load W, the length of elasto-plastic zone of the plastic hinge, is (A) L/2 (B) L/3 (C) L/4 (D) L/5
Last Answer : (B) L/3
Description : In case of a simply supported I-section beam of span L and loaded with a central load W, the length of elasto-plastic zone of the plastic hinge, is (A) L/2 (B) L/3 (C) L/4 (D) L/5
Last Answer : (D) L/5
Description : For a simply supported beam with a central load, the bending moment is (A) Least at the centre (B) Least at the supports (C) Maximum at the supports (D) Maximum at the centre
Last Answer : (D) Maximum at the centre
Description : A simply supported beam AB is subjected to a concentrated load at C, the centre of the span. The area of the SF diagram from A to C will give a) BM at C b) Load at S c) SF at C d)Difference between BM values at A and C
Last Answer : d)Difference between BM values at A and C
Description : The maximum deflection of a simply supported beam of span L, carrying an isolated load at the centre of the span; flexural rigidity being EI, is (A) WL3 /3EL (B) WL3 /8EL (C) WL3 /24EL (D) WL3 /48EL
Last Answer : (D) WL3 /48EL
Description : If a bent tendon is required to balance a concentrated load W at the centre of the span L, the central dip h must be at least (A) WL/P (B) WL/2P (C) WL/3P (D) WL/4P
Last Answer : Answer: Option D
Description : A simply supported beam is of rectangular section.It carries a uniformly distributed load over the whole span.The deflection at the centre is y.If the depth of beam is doubled ,the deflection at the centre would be a.2y b.4y c.y/2 d.y/8.
Last Answer : d.y/8.
Description : A simply supported beam which carries a uniformly distributed load has two equal overhangs. To have maximum B.M. produced in the beam least possible, the ratio of the length of the overhang to the total length of the beam, is (A) 0.207 (B) 0.307 (C) 0.407 (D) 0.508
Last Answer : (A) 0.207
Description : A simply supported beam carries uniformly distributed load of 20 kN/m over the length of 5 m. If flexural rigidity is 30000 kN.m2, what is the maximum deflection in the beam? a. 5.4 mm b. 1.08 mm c. 6.2 mm d. 8.6 mm
Last Answer : a. 5.4 mm
Description : A simply supported beam carries a uniformly distributed load over the whole span.The deflection at the centre is y.If the distributed load per unit length is doubled and also depth of beam is doubled ,then the deflection at the centre would be a.2y b.4y c.y/2 d.y/4.
Last Answer : d.y/4.
Description : A beam of length L is pinned at both ends and is subjected to a concentrated bending couple of moment M at its centre. The maximum bending moment in the beam is (A) M (B) M/2 (C) M/3 (D) ML/2
Last Answer : (A) M
Description : Design of R.C.C. simply supported beams carrying U.D.L. is based on the resultant B.M. at (A) Supports (B) Mid span (C) Every section (D) Quarter span
Last Answer : Answer: Option B
Description : A uniform girder simply supported at its ends is subjected to a uniformly distributed load over its entire length and is propped at the centre so as to neutralise the deflection. The net B.M. at the centre will be (A) WL (B) WL/8 (C) WL/24 (D) WL/32
Last Answer : (D) WL/32
Description : The ratio of the maximum deflections of a simply supported beam with a central load W and of a cantilever of same length and with a load W at its free end, is (A) 1/8 (B) 1/10 (C) 1/12 (D) 1/16
Last Answer : (D) 1/16
Description : If the maximum shear stress at the end of a simply supported R.C.C. beam of 16 m effective span is 10 kg/cm2 , the length of the beam having nominal reinforcement, is (A) 8 cm (B) 6 m (C) 8 m (D) 10 m
Description : A simply supported beam 6 m long and of effective depth 50 cm, carries a uniformly distributed load 2400 kg/m including its self weight. If the lever arm factor is 0.85 and permissible tensile stress of steel is 1400 kg/cm2 ... area of steel required, is (A) 14 cm (B) 15 cm2 (C) 16 cm2 (D) 17 cm