In counterfort retaining walls, the main reinforcement in the stem at support is (A) Not provided (B) Provided only on inner face (C) Provided only on front face (D) Provided both on inner and front faces

In counterfort retaining walls, the main reinforcement in the stem at support is
(A) Not provided
(B) Provided only on inner face
(C) Provided only on front face
(D) Provided both on inner and front faces
by

1 Answer

Answer :

Answer: Option B
by

Related questions

In a counterfort retaining wall, the main reinforcement in the stem at mid span is provided on (A) Front face only (B) Inner face only (C) Both front face and inner face (D) None of the above

Description : In a counterfort retaining wall, the main reinforcement in the stem at mid span is provided on (A) Front face only (B) Inner face only (C) Both front face and inner face (D) None of the above

Last Answer : Answer: Option A

In T-shaped R C. retaining walls, the main reinforcement in the stem is provided on (A) The front face in one direction (B) The front face in both directions (C) The inner face in one direction (D) The inner face in both directions

Description : In T-shaped R C. retaining walls, the main reinforcement in the stem is provided on (A) The front face in one direction (B) The front face in both directions (C) The inner face in one direction (D) The inner face in both directions

Last Answer : Answer: Option C

In the design of a front counterfort in a counterfort retaining wall, the main reinforcement is provided on (i) Bottom face near counterfort (ii) Top face near counterfort (iii) Bottom face near centre of span (iv) Top face near centre of span The correct answer is (A) Only (i) (B) Only (ii) (C) Both (i) and (iv) (D) Both (ii) and (iii)

Description : In the design of a front counterfort in a counterfort retaining wall, the main reinforcement is provided on (i) Bottom face near counterfort (ii) Top face near counterfort (iii) Bottom face near centre of span (iv) Top ... ) (B) Only (ii) (C) Both (i) and (iv) (D) Both (ii) and (iii)

Last Answer : Answer: Option C

In a counterfort retaining wall, the main reinforcement is provided on the (i) Bottom face in front counterfort (ii) Inclined face in front counterfort (iii) Bottom face in back counterfort (iv) Inclined face in back counterfort The correct answer is (A) (i) and (ii), (B) (ii) and (iii) (C) (i) and (iv) (D) (iii) and (iv)

Description : In a counterfort retaining wall, the main reinforcement is provided on the (i) Bottom face in front counterfort (ii) Inclined face in front counterfort (iii) Bottom face in back counterfort (iv) Inclined face in back counterfort ... (B) (ii) and (iii) (C) (i) and (iv) (D) (iii) and (iv)

Last Answer : Answer: Option C

The temperature reinforcement in the vertical slab of a T-shaped R.C. retaining wall is (A) Not needed (B) Provided equally on inner and front faces (C) Provided more on inner face than on front face (D) Provided more on front face than on inner face

Description : The temperature reinforcement in the vertical slab of a T-shaped R.C. retaining wall is (A) Not needed (B) Provided equally on inner and front faces (C) Provided more on inner face than on front face (D) Provided more on front face than on inner face

Last Answer : Answer: Option D

The main reinforcement in the heel of a T-shaped R.C. retaining wall is provided on (A) Top face perpendicular to wall (B) Bottom face perpendicular to wall (C) Both top and bottom faces perpendicular to wall (D) None of these

Description : The main reinforcement in the heel of a T-shaped R.C. retaining wall is provided on (A) Top face perpendicular to wall (B) Bottom face perpendicular to wall (C) Both top and bottom faces perpendicular to wall (D) None of these

Last Answer : Answer: Option A

The main reinforcement in the toe of a T-shaped R C. retaining wall is provided on (i) Top face parallel to the wall (ii) Top face perpendicular to the wall (iii) Bottom face parallel to the wall (iv) Bottom face perpendicular to the wall The correct answer is (A) Only (ii) is correct (B) (i) and (ii) are correct (C) (iii) and (iv) are correct (D) Only (iv) is correct

Description : The main reinforcement in the toe of a T-shaped R C. retaining wall is provided on (i) Top face parallel to the wall (ii) Top face perpendicular to the wall (iii) Bottom face parallel to the wall (iv) ... (i) and (ii) are correct (C) (iii) and (iv) are correct (D) Only (iv) is correct

Last Answer : Answer: Option D

In counterfort type retaining walls (i) The vertical slab is designed as a continuous slab (ii) The heel slab is designed as a continuous slab (iii) The vertical slab is designed as a cantilever (iv) The heel slab is designed as a cantilever The correct answer is (A) (i) and (ii) (B) (i)and(iv) (C) (ii) and (iii) (D) (iii) and (iv)

Description : In counterfort type retaining walls (i) The vertical slab is designed as a continuous slab (ii) The heel slab is designed as a continuous slab (iii) The vertical slab is designed as a cantilever (iv) The heel slab is designed ... (ii) (B) (i)and(iv) (C) (ii) and (iii) (D) (iii) and (iv)

Last Answer : Answer: Option A

Which of the following R.C. retaining walls is suitable for heights beyond 6 m? (A) L-shaped wall (B) T-shaped wall (C) Counterfort type (D) All of the above

Description : Which of the following R.C. retaining walls is suitable for heights beyond 6 m? (A) L-shaped wall (B) T-shaped wall (C) Counterfort type (D) All of the above

Last Answer : Answer: Option C

Pick up the incorrect statement from the following: (A) In the stem of a retaining wall, reinforcement is provided near the earth side (B) In the toe slab of a retaining wall, reinforcement is provided at the bottom of the slab (C) In the heel slab of a retaining wall, reinforcement is provided at the top of the slab (D) None of these

Description : Pick up the incorrect statement from the following: (A) In the stem of a retaining wall, reinforcement is provided near the earth side (B) In the toe slab of a retaining wall, reinforcement is ... slab of a retaining wall, reinforcement is provided at the top of the slab (D) None of these

Last Answer : Answer: Option D

Retaining walls are generally constructed with dry rubble stones with 60 cm top width and (A) 1 : 2 front batter (B) 1 : 3 front batter (C) 1 : 4 front batter (D) 1 : 5 front batter

Description : Retaining walls are generally constructed with dry rubble stones with 60 cm top width and (A) 1 : 2 front batter (B) 1 : 3 front batter (C) 1 : 4 front batter (D) 1 : 5 front batter

Last Answer : Answer: Option B

The effective span of a simply supported slab, is (A) Distance between the centres of the bearings (B) Clear distance between the inner faces of the walls plus twice the thickness of the wall (C) Clear span plus effective depth of the slab (D) None of these

Description : The effective span of a simply supported slab, is (A) Distance between the centres of the bearings (B) Clear distance between the inner faces of the walls plus twice the thickness of the wall (C) Clear span plus effective depth of the slab (D) None of these

Last Answer : Answer: Option B

The effective span of a simply supported slab is (a) Distance between the centers of the bearings (b) Clear distance between the inner faces of the walls plus twice he thickness of the slab. (c) Cleat spa plus effective depth of the slab. (d) All the above

Description : The effective span of a simply supported slab is (a) Distance between the centers of the bearings (b) Clear distance between the inner faces of the walls plus twice he thickness of the slab. (c) Cleat spa plus effective depth of the slab. (d) All the above

Last Answer : (c) Cleat spa plus effective depth of the slab.

Parapet walls along hill roads, are provided (A) To retain the back filling (B) To prevent the hill from sliding (C) To prevent the wheels of the vehicle from coming on the retaining wall (D) None of these

Description : Parapet walls along hill roads, are provided (A) To retain the back filling (B) To prevent the hill from sliding (C) To prevent the wheels of the vehicle from coming on the retaining wall (D) None of these

Last Answer : Answer: Option C

In retaining and breast walls, weep holes are provided at (A) 50 cm vertical height and 50 cm centre to centre horizontally (B) 100 cm vertical height and 100 cm centre to centre horizontally (C) 100 cm vertical height and 120 cm centre to centre horizontally (D) 120 cm vertical height and 100 cm centre to centre horizontally

Description : In retaining and breast walls, weep holes are provided at (A) 50 cm vertical height and 50 cm centre to centre horizontally (B) 100 cm vertical height and 100 cm centre to centre horizontally ... cm centre to centre horizontally (D) 120 cm vertical height and 100 cm centre to centre horizontally

Last Answer : Answer: Option C

Construction joints are generally provided in concrete (A) Roads (B) Retaining walls (C) Lining of canals (D) All the above

Description : Construction joints are generally provided in concrete (A) Roads (B) Retaining walls (C) Lining of canals (D) All the above

Last Answer : Answer: Option D

Weep holes are provided in retaining and breast walls (A) To drain off the water from the filling (B) To ventilate the stone masonry (C) To add architectural beauty (D) To increase compaction of the earth retained

Description : Weep holes are provided in retaining and breast walls (A) To drain off the water from the filling (B) To ventilate the stone masonry (C) To add architectural beauty (D) To increase compaction of the earth retained

Last Answer : Answer: Option A

The thickness of base slab of a retaining wall generally provided, is (A) One half of the width of the stem at the bottom (B) One-third of the width of the stem at the bottom (C) One fourth of the width of the steam at the bottom (D) Width of the stem at the bottom

Description : The thickness of base slab of a retaining wall generally provided, is (A) One half of the width of the stem at the bottom (B) One-third of the width of the stem at the bottom (C) One fourth of the width of the steam at the bottom (D) Width of the stem at the bottom

Last Answer : Answer: Option D

The stepped structure provided for lateral support of a structure, is (A) Retaining wall (B) Breast wall (C) Buttress (D) Parapet wall

Description : The stepped structure provided for lateral support of a structure, is (A) Retaining wall (B) Breast wall (C) Buttress (D) Parapet wall

Last Answer : Answer: Option C

Side face reinforcement shall be provided in the beam when depth of the web in a beam exceeds (A) 50 cm (B) 75 cm (C) 100 cm (D) 120 cm

Description : Side face reinforcement shall be provided in the beam when depth of the web in a beam exceeds (A) 50 cm (B) 75 cm (C) 100 cm (D) 120 cm

Last Answer : Answer: Option B

Side face reinforcement is provided when the depth of beam exceeds [ A ] 250 mm [ B ] 450 mm [ C ] 550 mm [ D ] 750 mm

Description : Side face reinforcement is provided when the depth of beam exceeds [ A ] 250 mm [ B ] 450 mm [ C ] 550 mm [ D ] 750 mm

Last Answer : [ D ] 750 mm

The smoothened surface of the front face of the guay walls, is known as fending which is made of (A) Granite stone (B) Timber (C) Steel (D) All the above

Description : The smoothened surface of the front face of the guay walls, is known as fending which is made of (A) Granite stone (B) Timber (C) Steel (D) All the above

Last Answer : (D) All the above

What is the function of shear keys in the design of retaining walls?

Description : What is the function of shear keys in the design of retaining walls?

Last Answer : In determining the external stability of retaining walls, failure modes like bearing failure, sliding and overturning are normally considered in design. In considering the criterion of sliding, the sliding ... instead of 0.8φ in the previous case and the sliding resistance can be enhanced.

Cantilever retaining walls can safely be used for a height not more than (A) 3 m (B) 4 m (C) 5 m (D) 6 m

Description : Cantilever retaining walls can safely be used for a height not more than (A) 3 m (B) 4 m (C) 5 m (D) 6 m

Last Answer : Answer: Option D

The walls which are necessary on the hill side of roadway where earth has to be retained from slipping is known as (A) Retaining wall (B) Breast wall (C) Parapet wall (D) None of the above

Description : The walls which are necessary on the hill side of roadway where earth has to be retained from slipping is known as (A) Retaining wall (B) Breast wall (C) Parapet wall (D) None of the above

Last Answer : Answer: Option B

For the design of retaining walls, the minimum factor of safety against overturning is taken as (A) 1.5 (B) 2.0 (C) 2.5 (D) 3.0

Description : For the design of retaining walls, the minimum factor of safety against overturning is taken as (A) 1.5 (B) 2.0 (C) 2.5 (D) 3.0

Last Answer : Answer: Option B

Stones used for the construction of retaining walls must be (A) Soft (B) Hard (C) Light (D) Heavy

Description : Stones used for the construction of retaining walls must be (A) Soft (B) Hard (C) Light (D) Heavy

Last Answer : Answer: Option D

Refractory bricks are used for (A) Retaining walls (B) Columns (C) Piers (D) Combustion chambers

Description : Refractory bricks are used for (A) Retaining walls (B) Columns (C) Piers (D) Combustion chambers

Last Answer : Answer: Option D

A heavy stone is suitable for (A) Arches (B) Rubble masonry (C) Roads (D) Retaining walls

Description : A heavy stone is suitable for (A) Arches (B) Rubble masonry (C) Roads (D) Retaining walls

Last Answer : Answer: Option D

The cement, widely used in retaining walls, is (a) R.H.C (b) L.H.C (c) S.R.C. (d) O.P.C.

Description : The cement, widely used in retaining walls, is (a) R.H.C (b) L.H.C (c) S.R.C. (d) O.P.C.

Last Answer : (b) L.H.C

The transverse reinforcements provided at right angles to the main reinforcement (A) Distribute the load (B) Resist the temperature stresses (C) Resist the shrinkage stress (D) All the above

Description : The transverse reinforcements provided at right angles to the main reinforcement (A) Distribute the load (B) Resist the temperature stresses (C) Resist the shrinkage stress (D) All the above

Last Answer : Answer: Option D

The transverse reinforcements provided at right angles to the main reinforcement. (a) To distribute the load. (b) To resist the temp stresses (c) To resist the shrinkage stresses (d) All the above

Description : The transverse reinforcements provided at right angles to the main reinforcement. (a) To distribute the load. (b) To resist the temp stresses (c) To resist the shrinkage stresses (d) All the above

Last Answer : (d) All the above

The stem of a cantilever retaining wall which retains earth level with top is 6 m. If the angle of repose and weight of the soil per cubic metre are 30° and 2000 kg respectively, the effective width of the stem at the bottom, is (A) 51.5 (B) 52.5 (C) 53.5 (D) 54.5

Description : The stem of a cantilever retaining wall which retains earth level with top is 6 m. If the angle of repose and weight of the soil per cubic metre are 30° and 2000 kg respectively, the effective width of the stem at the bottom, is (A) 51.5 (B) 52.5 (C) 53.5 (D) 54.5

Last Answer : Answer: Option C

In a cantilever retaining wall without a heel slab (A) Thickness of the stem is kept same throughout (B) Base slab is made 10 cm thicker than the stem (C) Width of the base slab is kept 0.7 time the total height of the wall (D) All the above

Description : In a cantilever retaining wall without a heel slab (A) Thickness of the stem is kept same throughout (B) Base slab is made 10 cm thicker than the stem (C) Width of the base slab is kept 0.7 time the total height of the wall (D) All the above

Last Answer : Answer: Option D

For walls, columns and vertical faces of all structural members, the form work is generally removed after (A) 24 to 48 hours (B) 3 days (C) 7 days (D) 14 days

Description : For walls, columns and vertical faces of all structural members, the form work is generally removed after (A) 24 to 48 hours (B) 3 days (C) 7 days (D) 14 days

Last Answer : Answer: Option A

If is the overall height of a retaining wall retaining a surcharge, the width of the base slab usually provided, is (A) 0.3 H(B) 0.4 H(C) 0.5 H(D) 0.7 H

Description : If is the overall height of a retaining wall retaining a surcharge, the width of the base slab usually provided, is (A) 0.3 H (B) 0.4 H (C) 0.5 H (D) 0.7 H

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) The breakwater which can be used as a platform for loading and unloading of cargo is called a mole (B) The brick masonry retaining wall which is used for loading and unloading of cargo is called quay wall (C) Three types of break waters are generally provided in harbours (D) All of the above

Description : Pick up the correct statement from the following: (A) The breakwater which can be used as a platform for loading and unloading of cargo is called a mole (B) The brick masonry retaining wall which is ... wall (C) Three types of break waters are generally provided in harbours (D) All of the above

Last Answer : (D) All of the above

Pick up the incorrect statement from the following: (A) The retaining wall should be structurally capable to resist the applied earth pressure (B) The section of the retaining wall should be so proportioned that it may not overturn by the lateral pressure (C) The retaining wall should be safe against sliding (D) To drain off water from the earth retained, weep holes are provided near the top of the retaining wall

Description : Pick up the incorrect statement from the following: (A) The retaining wall should be structurally capable to resist the applied earth pressure (B) The section of the retaining wall should be so ... off water from the earth retained, weep holes are provided near the top of the retaining wall

Last Answer : Answer: Option D

In a doubly reinforced beam , steel reinforcement is provided in a (a) Tensile zone (b) Compression zone (c) Either (a) & (b) (d) Both (a) & (b)

Description : In a doubly reinforced beam , steel reinforcement is provided in a (a) Tensile zone (b) Compression zone (c) Either (a) & (b) (d) Both (a) & (b)

Last Answer : (d) Both (a) & (b)

Total pressure on the vertical face of a retaining wall of height h acts parallel to free surface and from the base at a distance of (A) h/4 (B) h/3 (C) h/2 (D) 2h/3

Description : Total pressure on the vertical face of a retaining wall of height h acts parallel to free surface and from the base at a distance of (A) h/4 (B) h/3 (C) h/2 (D) 2h/3

Last Answer : Answer: Option B

Do I need to consult an engineer or a geologist before I take down retaining walls on my property?

Description : Do I need to consult an engineer or a geologist before I take down retaining walls on my property?

Last Answer : No, you shouldn't need to consult an engineer or geologist regarding removing retaining walls. You will want to make sure that whoever you hire is licensed/bonded and insuranced just in case they cause any damage.

How can I identify retaining walls?

Description : How can I identify retaining walls?

Last Answer : Retaining walls are the perfect option to separate your space from yards or anywhere else. Looking for design and installation ideas to maintain wall construction in your yard? We have something for ... living spaces. We pride ourselves on delivering outstanding quality work on time and on budget.

Development length is the length or extension that should be provided on either side from the [ A ] face of the support [ B ] point of maximum tension [ C ] point of maximum compression [ D ] point of minimum compression

Description : Development length is the length or extension that should be provided on either side from the [ A ] face of the support [ B ] point of maximum tension [ C ] point of maximum compression [ D ] point of minimum compression

Last Answer : [ B ] point of maximum tension

Development length is the length or extension that should be provided on either side from the [ A ] face of the support [ B ] point of maximum tension [ C ] point of maximum compression [ D ] point of minimum compression

Description : Development length is the length or extension that should be provided on either side from the [ A ] face of the support [ B ] point of maximum tension [ C ] point of maximum compression [ D ] point of minimum compression

Last Answer : [ B ] point of maximum tension

In the design of a simply supported skew bridge, which direction of reinforcement should be provided?

Description : In the design of a simply supported skew bridge, which direction of reinforcement should be provided?

Last Answer : In the conventional design of steel reinforcement for a simply supported skew bridge, a set of reinforcement is usually placed parallel to free edge while the other set is designed parallel ... ). In this way, considerable savings would be obtained from the orthogonal arrangement of reinforcement.

The shear reinforcement in R.C.C. is provided to resist (A) Vertical shear (B) Horizontal shear (C) Diagonal compression (D) Diagonal tension

Description : The shear reinforcement in R.C.C. is provided to resist (A) Vertical shear (B) Horizontal shear (C) Diagonal compression (D) Diagonal tension

Last Answer : Answer: Option D

Distribution reinforcement in a simply supported slab, is provided to distribute (A) Load (B) Temperature stress (C) Shrinkage stress (D) All the above

Description : Distribution reinforcement in a simply supported slab, is provided to distribute (A) Load (B) Temperature stress (C) Shrinkage stress (D) All the above

Last Answer : Answer: Option D

An R.C.C. beam not provided with shear reinforcement may develop cracks in its bottom inclined roughly to the horizontal at (A) 25° (B) 35° (C) 45° (D) 55°

Description : An R.C.C. beam not provided with shear reinforcement may develop cracks in its bottom inclined roughly to the horizontal at (A) 25° (B) 35° (C) 45° (D) 55°

Last Answer : Answer: Option C

If the shear stress in a R.C.C. beam is (A) Equal or less than 5 kg/cm2 , no shear reinforcement is provided (B) Greater than 4 kg/cm2 , but less than 20 kg/cm2 , shear reinforcement is provided (C) Greater than 20 kg/cm2 , the size of the section is changed (D) All the above

Description : If the shear stress in a R.C.C. beam is (A) Equal or less than 5 kg/cm2 , no shear reinforcement is provided (B) Greater than 4 kg/cm2 , but less than 20 kg/cm2 , shear reinforcement is provided (C) Greater than 20 kg/cm2 , the size of the section is changed (D) All the above

Last Answer : Answer: Option D

In the zone of R.C.C. beam where shear stress is less than 5 kg/cm2 , nominal reinforcement is provided at a pitch of (A) One-half lever arm of the section (B) One-third lever arm of the section (C) Lever arm of the section (D) One and half lever arm of the section

Description : In the zone of R.C.C. beam where shear stress is less than 5 kg/cm2 , nominal reinforcement is provided at a pitch of (A) One-half lever arm of the section (B) One-third lever arm of the section (C) Lever arm of the section (D) One and half lever arm of the section

Last Answer : Answer: Option C