x

speed control methods of three phase induction motor?

376 views

2 Answers

Answer :

Speed control of three phase induction motor

•There are two types of AC motor one is synchronous motor and second is asynchronous motor (induction motor).

•Three phase induction motor is a self starting motor.

•Motor have two main parts one is stator and second is rotor.

•Speed of three phase induction motor can be control from stator side and rotor side.

•The main method for controlling speed of induction motor are one is by changing number of poles second is by stator voltage control third is by V/F control and fourth is by rotor resistance control.

By changing number of poles :

•This method is use for squirrel cage rotor motor only.

image

•The number of stator poles can be change by three methods one is multiple stator winding and second is method of consequent poles and third is pole amplitude modulation.

•We have,"    N_s =  120f/P

•Where, N_s  is the synchronous speed , f is the frequency , P is the number of poles.

•So by changing the number of poles synchronous speed changes.

By stator voltage control :

•We have, 

image

•Torque is directly proportional to stator voltage.

•This method is very easy and cheap but still use rarely.

•Because by decreasing the voltage torque will reduce.

•But this will increase current in motor which will heat the motor which is not good it causes losses.

•Also the torque is proportional to square of voltage so large voltage change is required for changing torque.

By V/F control :

•We have,  N_s=  120f/P

•Where, N_s  is the synchronous speed , f is the frequency , P is the number of poles.

•Also, V=4.44φfTK  ( which means φ α V/f ).

•Where, V is the voltage , φ is the flux , f is the frequency , T is number of turns per phase , K is the winding constant.

•If we increase the frequency (f) flux (φ) will decrease because they are inversely proportional and if we increase the voltage (V ) flux (φ) will increase because they are directly proportional.

•In this method we have to keep V/f ratio constant.

By Rotor resistance control :

•We have, Torque α slip/(rotor resistance)

•This method is use for wound rotor motor only.

image

•By adding external variable resistance to rotor via slip ring we can control the speed of motor.

•It can also use as starter.

•It is simple method.

•But there is resistance means heat means losses means less efficiency.

Like 0 like

Answer :

Speed control of three phase induction motor

image

image

image

image

image

image

Like 0 like

Please log in or register to answer this question.

Related Questions


The speed of a three-phase induction motor is controlled by variable voltage variable frequency control (i.e. keeping V/f constant). As the frequency is reduced, the slip at maximum torque  (1) Decreases (2) Increases (3) Remains constant (4) None of the above
Last Answer : The speed of a three-phase induction motor is controlled by variable voltage variable frequency control (i.e. keeping V/f constant). As the frequency is reduced, the slip at maximum torque Increases 

Show More

239 views 1 answer



The slip of 400 V, three phase, 4 -pole induction motor when rotating at 1440 rpm is 
Last Answer : The slip of 400 V, three phase, 4 -pole induction motor when rotating at 1440 rpm is 4 percent

Show More

365 views 1 answer



How is a three phase cage induction motor self starting?
Last Answer : Any type of induction motor is self starting. Because the reason for torqe production require two flux displaced by some angle theta.If theta is constant with time then torqe will be constant;if ... torqe also pulsating. In induction motor this angle theta is not pulsating.so it is self starting 

Show More

160 views 1 answer



What is mean by plugging in three phase induction motor?
Last Answer : Plugging in three-phase induction motor means interchanging of any two phases of a stator for quick stopping.

Show More

158 views 1 answer



What are the speed control methods of dc motor?
Last Answer : Field control of DC motor Armature control of DC motor

Show More

263 views 2 answers



Split phase induction motor
Last Answer : Split phase induction motor : There are two windings used in split phase induction motor. It is a type of single-phase induction motor. There are two winding one is called main winding and ... motor have low starting torque it is used for small fans, blowers, centrifugal pumps, grinders etc.

Show More

233 views 1 answer






Last Answer : If a single phase induction motor runs slower than normal, the most likely defect is worn bearings.

Show More

170 views 1 answer



How does a single phase induction motor work?
Last Answer : As we know that single phase induction is not self started because for self started we require atleast two revolving field but single phase induction motor has only one. So we provide extra ... 1phase IM classified as split phase IM, capacitor start capacitor run, capacitor start induction run.

Show More

124 views 1 answer



explain the working of single phase induction motor.
Last Answer : Stator has two winding namely main winding and auxiliary winding.when single phase ac supply is given to the motor,its produces alternating field.this field cut by a cage rotor.so some emf ... due to this emf,rotor flux produced.the interaction between two fluxes produce torque.so rotor rotates.

Show More

188 views 1 answer



Single Phase Induction Motor
Last Answer : Single Phase Induction Motor Single phase induction motor is mostly used in home, office, shop and many single phase appliances like pumps,  ... torque and silent operation. It is uses where silent operation is required.

Show More

528 views 1 answer




Last Answer : Speed torque characteristic of a repulsion induction motor is similar to that of a D.C. compound motor.

Show More

169 views 1 answer




Last Answer : Series motor has the poorest speed control.

Show More

103 views 1 answer




Last Answer : Speed control of a universal motor is achieved by varying field flux with tapped field windings, connecting rheostat in series, applying variable voltage by means of silicon controlled rectifier, applying variable voltage by means of variable auto-transformer.

Show More

104 views 1 answer




Last Answer : The speed control of universal motor used for sewing machines is by varying the resistance.

Show More

105 views 1 answer



Explain with neat circuit diagrams the procedures to perform no load and blocked rotor tests on three phase induction motor.

Show More

157 views 0 answers





State any four advantages of three phase induction motor. 
Last Answer : Advantages of three phase induction motor https://youtu.be/27OIOCKN05U

Show More

141 views 2 answers



how can we reverse the direction of rotation of three phase induction motor ?
Last Answer : The direction of rotation of three phase induction motor can be reversed by plugging i.e by changing any two out of three phases of the supply to the stator of the Induction motor terminal.

Show More

139 views 1 answer



Explain the working of a single phase capacitor start induction motor. 
Last Answer : Single phase capacitor start induction motor https://youtu.be/31lvvzU5Puc

Show More

418 views 2 answers



What is the slip (as a percentage) when a 6 pole single phase induction motor operating on 220 V and 60 Hz is rotating at speed of 1140 rpm? A) 60% B) 5% C) 10% D) None of these
Last Answer : What is the slip (as a percentage) when a 6 pole single phase induction motor operating on 220 V and 60 Hz is rotating at speed of 1140 rpm? A) 60% B) 5% C) 10% D) None of these

Show More

127 views 1 answer




Last Answer : Single phase induction motor usually operates on 0.6 power factor lagging.

Show More

127 views 1 answer



A capacitor-start single phase induction motor is switched on to supply with its capacitor replaced by an inductor of equivalent reactance value. It will?
Last Answer : A capacitor-start single phase induction motor is switched on to supply with its capacitor replaced by an inductor of equivalent reactance value. It will not start at all.

Show More

236 views 1 answer



The synchronous speed of an 8 pole induction motor supplied power from a 50 Hz source will be ?
Last Answer : Ns         equals        f/pair pole 50/4      - 12.5

Show More

202 views 2 answers



Speed control of the motor using TRIAC
Last Answer : Speed control of the motor using TRIAC:  This basic phase triggering circuit uses the triac in series with the motor across an AC sinusoidal supply. The variable resistor, VR1 is used ... meaning that it may not trigger at the exact same point for each positive and negative half cycle.

Show More

273 views 1 answer



A 3-phase, 4-pole, 50Hz induction motor runs at a speed of 1440 rpm. The rotating field produced by the rotor rotates at a speed of ________ rpm with respect to stator field. (A) 1500 (B) 0 (C) 1440 (D) 60
Last Answer : 0

Show More

2.1k views 2 answers



In a 3-phase slip-ring induction motor, the slip at some speed is 0.05. The speed is reduced by inserting an external resistance in the rotor circuit and the slip is 0.15. If the rotor winding resistance per phase is 0.2 Ω, the external resistance is (A) 0.2 Ω (B) 0.3 Ω (C) 0.4 Ω (D) 0.5 Ω
Last Answer : In a 3-phase slip-ring induction motor, the slip at some speed is 0.05. The speed is reduced by inserting an external resistance in the rotor circuit and the slip is 0.15. If the rotor winding resistance per phase is 0.2 Ω, the external resistance is 0.3 Ω

Show More

169 views 1 answer



Torque developed by a three-phase, 400V, induction motor is 100 N -m. If the applied voltage is reduced to 200-V, the d'veloped torque will be
Last Answer : Torque developed by a three-phase, 400V, induction motor is 100 N -m. If the applied voltage is reduced to 200-V, the d'veloped torque will be 25 N -m

Show More

435 views 1 answer



A 400 V, 50 Hz three-phase induction motor rotates at 1440 rpm on full -load. The motor is wound for
Last Answer : A 400 V, 50 Hz three-phase induction motor rotates at 1440 rpm on full -load. The motor is wound for 4 poles

Show More

311 views 1 answer



An 8-pole, 50Hz, three-phase induction motor is running at 705rpm and has a rotor copper loss of 5kW. Its rotor input is (A) 5.06 kW (B) 0.3 kW (C) 100 kW (D) 83.33 kW
Last Answer : An 8-pole, 50Hz, three-phase induction motor is running at 705rpm and has a rotor copper loss of 5kW. Its rotor input is 83.33 kW

Show More

180 views 1 answer



In a split-phase induction motor, the resistance/reactance ratios of windings are such that (A) current in the auxiliary winding leads the current in the main winding (B) current in the ... (C) both windings develop the same starting torque (D) both windings develop high starting current
Last Answer : In a split-phase induction motor, the resistance/reactance ratios of windings are such that current in the auxiliary winding leads the current in the main winding

Show More

107 views 1 answer



In a single-phase induction motor when the rotor is stationary and voltage is applied to the stator, then (A) the flux is constant (B) the flux first decreases and then increases in ... increases and decreases in the opposite direction with the same magnitude (D) current flows through the rotor
Last Answer : In a single-phase induction motor when the rotor is stationary and voltage is applied to the stator, then the flux first decreases and then increases in the same direction

Show More

95 views 1 answer



The torque developed by any 3-phase induction motor at 0.8 p.u. slip is (A) Full-load torque (B) unstable torque (C) starting torque (D) break down
Last Answer : The torque developed by any 3-phase induction motor at 0.8 p.u. slip is unstable torque

Show More

3.1k views 1 answer




Last Answer : If starting winding of a single-phase induction motor is left in the circuit, it will draw excessive current and overheat.

Show More

236 views 1 answer




Last Answer : Capacitor start motor has high torque in starting

Show More

137 views 1 answer



What is the operation of three phase induction motor

Show More

7 views 0 answers




Last Answer : Usually wide and sensitive speed control is desired in case of colliery winders.

Show More

142 views 1 answer




Last Answer : Speed control by Ward Leonard method gives uniform speed variation in both directions.

Show More

129 views 1 answer



In a double squirrel cage induction motor, good starting torque is produced as (A) Large current flows through the outer high resistance winding. (B) Large current flows through the inner high ... the outer high resistance winding. (D) Large current flows through the inner low resistance winding.
Last Answer : In a double squirrel cage induction motor, good starting torque is produced as Large current flows through the outer high resistance winding.

Show More

137 views 1 answer



A change of 4% in the supply voltage to an induction motor will produce a change of approximately
Last Answer : A change of 4% in the supply voltage to an induction motor will produce a change of approximately 8% in the rotor torque

Show More

491 views 1 answer



In an induction motor if the flux density is reduced to one-half, of its normal value then the torque will  (1) reduce to one-half (2) reduce to one-fourth (3) remain unchanged (4) increase four times
Last Answer : In an induction motor if the flux density is reduced.to one-half, of its normal value then the torque will reduce to one-fourth

Show More

374 views 1 answer




Last Answer : The rotor slots, in an induction motor, are usually not quite parallel to the shaft because it helps in reducing the tendency of the rotor teeth to remain under the stator teeth.

Show More

146 views 1 answer



Is induction motor is self starting?
Last Answer : Single phase induction motor is not self starting. Three phase induction motor is self starting.

Show More

112 views 1 answer



What is the definition of induction motor?
Last Answer : its working on magnetic base made by coils and its work with 1 phase or 3 phase ac or dc supply

Show More

123 views 1 answer



What is the function of induction motor?
Last Answer : while you give supply to motor its motor run on magnet base 

Show More

160 views 1 answer



At which time power factor of the induction motor is low?
Last Answer : The power factor of the inducction motor is low at the time of starting as compare to while the induction motor is running.

Show More

151 views 1 answer




Last Answer : Induction motor is a AC motor it is also known as asynchronous motor .

Show More

101 views 1 answer




Last Answer : if induction motor rotates exceed than its synchronous speed, it acts as a generator.

Show More

68 views 1 answer



Induction motor
Last Answer : Induction Motor Inductor is a coil of wire which possess the property of inductance. Inductance is the property of an electric conductor which generate electromotive force (EMF ... motor are classified as slip ring induction motor and squirrel cage induction motor.

Show More

80 views 1 answer



The speed of a 2-pole, 3-phase stepper motor operated by 1200 pulses/min (A) 100 rpm (B) 200 rpm (C) 400 rpm (D) 800 rpm
Last Answer : The speed of a 2-pole, 3-phase stepper motor operated by 1200 pulses/min 200 rpm

Show More

158 views 1 answer


Show More⇦ PreviousNext ⇨