Fluid is a substance that (A) Cannot be subjected to shear forces (B) Always expands until it fills any container (C) Has the same shear stress at a point regardless of its motion (D) Cannot remain at rest under action of any shear force

Fluid is a substance that
(A) Cannot be subjected to shear forces
(B) Always expands until it fills any container
(C) Has the same shear stress at a point regardless of its motion
(D) Cannot remain at rest under action of any shear force
by

1 Answer

Answer :

Answer: Option D
by

Related questions

A fluid is the one, which (A) Cannot remain at rest under the action of shear force (B) Continuously expands till it fills any container (C) Is incompressible (D) Permanently resists distortion

Description : A fluid is the one, which (A) Cannot remain at rest under the action of shear force (B) Continuously expands till it fills any container (C) Is incompressible (D) Permanently resists distortion

Last Answer : (A) Cannot remain at rest under the action of shear force

The pressure intensity is the same in all directions at a point in a fluid (A) Only when the fluid is frictionless (B) Only when the fluid is at rest having zero velocity (C) When there is no motion of one fluid layer relative to an adjacent layer (D) Regardless of the motion of one fluid layer relative to an adjacent layer

Description : The pressure intensity is the same in all directions at a point in a fluid (A) Only when the fluid is frictionless (B) Only when the fluid is at rest having zero velocity (C) When there is ... relative to an adjacent layer (D) Regardless of the motion of one fluid layer relative to an adjacent layer

Last Answer : C) When there is no motion of one fluid layer relative to an adjacent layer

A fluid is a substance, that (A) Has to be kept in a closed container (B) Is almost incompressible (C) Has zero shear stress (D) Flows when even a small shear is applied to it

Description : A fluid is a substance, that (A) Has to be kept in a closed container (B) Is almost incompressible (C) Has zero shear stress (D) Flows when even a small shear is applied to it

Last Answer : (D) Flows when even a small shear is applied to it

An object at rest will remain at rest and an object in motion will remain in motion until and unless it is acted upon by an external force. This is Newton's – (1) First law (2) Second law (3) Third law (4) Fourth law

Description : An object at rest will remain at rest and an object in motion will remain in motion until and unless it is acted upon by an external force. This is Newton's – (1) First law (2) Second law (3) Third law (4) Fourth law

Last Answer : (1) First law Explanation: Newton's first law of motion - sometimes referred to as the law of inertia-states that every object will remain at rest or in uniform motion in a straight line unless ... its state by the action of an external force. This is normally taken as the definition of inertia.

The center of pressure of a surface subjected to fluid pressure is the point (A) On the surface at which resultant pressure acts (B) On the surface at which gravitational force acts (C) At which all hydraulic forces meet (D) Similar to metacentre

Description : The center of pressure of a surface subjected to fluid pressure is the point (A) On the surface at which resultant pressure acts (B) On the surface at which gravitational force acts (C) At which all hydraulic forces meet (D) Similar to metacentre

Last Answer : Answer: Option A

The direct shear test suffers from the following disadvantage: (A) Drain condition cannot be controlled (B) Pore water pressure cannot be measured (C) Shear stress on the failure plane is not uniform (D) The area under the shear and vertical loads does not remain constant throughout the test

Description : The direct shear test suffers from the following disadvantage: (A) Drain condition cannot be controlled (B) Pore water pressure cannot be measured (C) Shear stress on the failure plane is not uniform (D) The area under the shear and vertical loads does not remain constant throughout the test

Last Answer : Answer: Option C

The normal stress is the same in all directions at a point in a fluid, only when the fluid (A) Is at rest & has zero viscosity (B) Is frictionless (C) Fluid layer has no motion relative to an adjacent layer of fluid (D) is incompressible & frictionless

Description : The normal stress is the same in all directions at a point in a fluid, only when the fluid (A) Is at rest & has zero viscosity (B) Is frictionless (C) Fluid layer has no motion relative to an adjacent layer of fluid (D) is incompressible & frictionless

Last Answer : (D) is incompressible & frictionless

05. In an internal mouthpiece, if the jet after contraction expands and fills up the whole mouthpiece, then the mouthpiece is said to be running free. A) True B) False

Description : 05. In an internal mouthpiece, if the jet after contraction expands and fills up the whole mouthpiece, then the mouthpiece is said to be running free. A) True B) False

Last Answer : B

05. In an internal mouthpiece, if the jet after contraction expands and fills up the whole mouthpiece, then the mouthpiece is said to be running free. A) True B) False

Description : 05. In an internal mouthpiece, if the jet after contraction expands and fills up the whole mouthpiece, then the mouthpiece is said to be running free. A) True B) False

Last Answer : A

When a section is subjected to two equal and opposite forces tangentially to the section, the stress produced is known as (a) Tensile stress (b) Lateral stress (c) Shear stress (d) No stress

Description : When a section is subjected to two equal and opposite forces tangentially to the section, the stress produced is known as (a) Tensile stress (b) Lateral stress (c) Shear stress (d) No stress

Last Answer : (c) Shear stress

When the helical compression spring is subjected to axial compressive force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Description : When the helical compression spring is subjected to axial compressive force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Last Answer : (D) Torsional shear stress

When the helical extension spring is subjected to axial tensile force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Description : When the helical extension spring is subjected to axial tensile force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Last Answer : (D) Torsional shear stress

A square object of 4 mm is subjected to a force of 3000 N. What is the maximum allowable shear stress acting on it? a. 250.14 mm2 b. 281.25 mm2 c. 400.32 mm2 d. 500 mm2

Description : A square object of 4 mm is subjected to a force of 3000 N. What is the maximum allowable shear stress acting on it? a. 250.14 mm2 b. 281.25 mm2 c. 400.32 mm2 d. 500 mm2

Last Answer : b. 281.25 mm2

A circular pipe is subjected to maximum shear force of 60 kN. What is the diameter of the pipe if maximum allowable shear stress is 5 Mpa? a. 27.311 mm b. 75.56 mm c. 142.72 mm d. 692.10 mm

Description : A circular pipe is subjected to maximum shear force of 60 kN. What is the diameter of the pipe if maximum allowable shear stress is 5 Mpa? a. 27.311 mm b. 75.56 mm c. 142.72 mm d. 692.10 mm

Last Answer : c. 142.72 mm

The normal stress is same in all directions at a point in a fluid (A) Only when the fluid is frictionless (B) Only when the fluid is incompressible and has zero viscosity (C) When there is no motion of one fluid layer relative to an adjacent layer (D) Irrespective of the motion of one fluid layer relative to an adjacent layer

Description : The normal stress is same in all directions at a point in a fluid (A) Only when the fluid is frictionless (B) Only when the fluid is incompressible and has zero viscosity (C) When there ... to an adjacent layer (D) Irrespective of the motion of one fluid layer relative to an adjacent layer

Last Answer : Answer: Option C

Pick out the wrong statement. (A) The shear stress at the pipe (dia = D, length = L) wall in case of laminar flow of Newtonian fluids is (D/4L). ∆p (B) In the equation, T. gc = k. (du/dy) n the value of 'n' for pseudoplastic and Dilatant fluid are < 1 and >1 respectively (C) Shear stress for Newtonian fluid is proportional to the rate of shear in the direction perpendicular to motion (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Description : Pick out the wrong statement. (A) The shear stress at the pipe (dia = D, length = L) wall in case of laminar flow of Newtonian fluids is (D/4L). ∆p (B) In the equation, T. gc = k. ... to motion (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Last Answer : (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

A shaft is subjected to bending moment M and a torque T simultaneously. The ratio of the maximum bending stress to maximum shear stress developed in the shaft, is (A) M/T (B) T/M (C) 2M/T (D) 2T/M

Description : A shaft is subjected to bending moment M and a torque T simultaneously. The ratio of the  maximum bending stress to maximum shear stress developed in the shaft, is  (A) M/T (B) T/M (C) 2M/T (D) 2T/M

Last Answer : (C) 2M/T

If the strain energy stored per unit volume in a hollow shaft subjected to a pure torque when t attains maximum shear stress fs the ratio of inner diameter to outer diameter, is 17/64 (fs/N) (A) 1/2 (B) 1/3 (C) 1/4 (D) 1/5

Description : If the strain energy stored per unit volume in a hollow shaft subjected to a pure torque  when t attains maximum shear stress fs  the ratio of inner diameter to outer diameter, is 17/64  (fs/N)  (A) 1/2  (B) 1/3  (C) 1/4  (D) 1/5

Last Answer : (C) 1/4 

If a solid shaft (diameter 20 cm, length 400 cm, N = 0.8 × 105 N/mm2 ) when subjected to a twisting moment, produces maximum shear stress of 50 N/mm2 , the angle of twist in radians, is (A) 0.001 (B) 0.002 (C) 0.0025 (D) 0.003

Description : If a solid shaft (diameter 20 cm, length 400 cm, N = 0.8 × 105  N/mm2 ) when subjected to a twisting  moment, produces maximum shear stress of 50 N/mm2 , the angle of twist in radians, is  (A) 0.001  (B) 0.002  (C) 0.0025  (D) 0.003 

Last Answer : (C) 0.0025 

shaft subjected to a bending moment M and a torque T, experiences (A) Maximum bending stress = 32M d 3 (B) Maximum shear stress = 16 T d 3 (C) Both (a) and (b) (D) Neither (a) nor (b)

Description :  shaft subjected to a bending moment M and a torque T, experiences  (A) Maximum bending stress = 32M d 3 (B) Maximum shear stress = 16 T d 3 (C) Both (a) and (b)  (D) Neither (a) nor (b)

Last Answer : (C) Both (a) and (b) 

Along the principal plan subjected to maximum principal stress (A) Maximum shear stress acts (B) Minimum shear stress acts(C) No shear stress acts (D) None of these

Description : Along the principal plan subjected to maximum principal stress (A) Maximum shear stress acts (B) Minimum shear stress acts (C) No shear stress acts (D) None of these

Last Answer : (C) No shear stress acts

The maximum load to which a fillet joint of length can be subjected to, is (A) 0.7 × S × fillet size × L (B) 2 × S × fillet size × L (C) Permissible shear stress × fillet size × L (D) (S × fillet size × L)/3

Description : The maximum load to which a fillet joint of length can be subjected to, is  (A) 0.7 × S × fillet size × L (B) 2 × S × fillet size × L (C) Permissible shear stress × fillet size × L (D) (S × fillet size × L)/3 

Last Answer : (A) 0.7 × S × fillet size × L

Pick up the correct statement from the following: (A) An unconfined compression test is a special case of triaxial compression test (B) An unconfined compression test is a special case of direct shear test (C) The confining pressure is maximum during an unconfined compression test (D) The cylindrical specimen of a soil is subjected to major principal stress till it fails due to shearing along the plane of the failure

Description : Pick up the correct statement from the following: (A) An unconfined compression test is a special case of triaxial compression test (B) An unconfined compression test is a special case of direct ... subjected to major principal stress till it fails due to shearing along the plane of the failure

Last Answer : Option A

Which of the following forces does not act on a fluid at rest? (A) Viscous force (B) Gravity force (C) Hydrostatic force (D) Surface tension force

Description : Which of the following forces does not act on a fluid at rest? (A) Viscous force (B) Gravity force (C) Hydrostatic force (D) Surface tension force

Last Answer : (A) Viscous force

When a shaft is subjected to a twisting moment, every cross-section of the shaft will be under (a) Tensile stress (b) Compressive stress (c) Shear stress (d) All of these

Description : When a shaft is subjected to a twisting moment, every cross-section of the shaft will be under (a) Tensile stress (b) Compressive stress (c) Shear stress (d) All of these

Last Answer : c) Shear stress

The normal stress in a fluid will be constant in all directions at a point only if (A) It is incompressible (B) It has uniform viscosity (C) It has zero viscosity (D) It is at rest

Description : The normal stress in a fluid will be constant in all directions at a point only if (A) It is incompressible (B) It has uniform viscosity (C) It has zero viscosity (D) It is at rest

Last Answer : Answer: Option D

According to principle of transmissibility of forces, the effect of a force upon a body is (A) Maximum when it acts at the center of gravity of a body (B) Different at different points in its line of action (C) The same at every point in its line of action (D) Minimum when it acts at the C.G. of the body

Description : According to principle of transmissibility of forces, the effect of a force upon a body is (A) Maximum when it acts at the center of gravity of a body (B) Different at different points in its line of action ... at every point in its line of action (D) Minimum when it acts at the C.G. of the body

Last Answer : (C) The same at every point in its line of action

__________ stress cannot be sustained by a fluid in equilibrium. (A) Shear (B) Tensile (C) Compressive

Description : __________ stress cannot be sustained by a fluid in equilibrium. (A) Shear (B) Tensile (C) Compressive

Last Answer : Option A

Which of the following statements regarding the use of a current measuring instrument is correct? A. It must be connected in series with the circuit. B. You should always start with the lowest range until a suitable reading is obtained. C. The indicating needle is deflected from left to right regardless of polarity. D. An external shunt is generally utilized where current is less than 10 amperes.

Description : Which of the following statements regarding the use of a current measuring instrument is correct? A. It must be connected in series with the circuit. B. You should always start with the lowest range ... of polarity. D. An external shunt is generally utilized where current is less than 10 amperes.

Last Answer : Answer: A

An arch may be subjected to (A) Shear and axial force (B) Bending moment and shear force (C) Bending moment and axial force (D) Thrust, shear force and bending moment

Description : An arch may be subjected to  (A) Shear and axial force  (B) Bending moment and shear force  (C) Bending moment and axial force  (D) Thrust, shear force and bending moment 

Last Answer : (D) Thrust, shear force and bending moment 

In a ring beam subjected to uniformly distributed load (i) Shear force at mid span is zero (ii) Shear force at mid span is maximum (iii) Torsion at mid span is zero (iv) Torsion at mid span is maximum The correct answer is (A) (i) and (iii) (B) (i) and (iv) (C) (ii) and (iii) (D) (ii) and (iv)

Description : In a ring beam subjected to uniformly distributed load (i) Shear force at mid span is zero (ii) Shear force at mid span is maximum (iii) Torsion at mid span is zero (iv) Torsion at mid span is maximum The correct answer ... and (iii) (B) (i) and (iv) (C) (ii) and (iii) (D) (ii) and (iv)

Last Answer : Option A

Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) None of the listed

Description : Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) None of the listed

Last Answer : b) Tensile

Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) None of the listed

Description : Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) None of the listed

Last Answer : b) Tensile

It is a secondary shaft used to counter the direction of main shaft. 81. Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) twisting

Description : It is a secondary shaft used to counter the direction of main shaft. 81. Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) twisting

Last Answer : b) Tensile

When equal and opposite forces applied to a body, tend to elongate it, the stress so produced, is called (A) Shear stress (B) Compressive stress (C) Tensile stress (D) Transverse stress

Description : When equal and opposite forces applied to a body, tend to elongate it, the stress so produced, is called (A) Shear stress (B) Compressive stress (C) Tensile stress (D) Transverse stress

Last Answer : (C) Tensile stress

In a cantilever subjected to a combination of concentrated load, uniformly distributed load and uniformly varying load, Maximum bending moment is (a) Where shear force=0 (b) At the free end (c) At the fixed end (d) At the mid-point

Description : In a cantilever subjected to a combination of concentrated load, uniformly distributed load and uniformly varying load, Maximum bending moment is (a) Where shear force=0 (b) At the free end (c) At the fixed end (d) At the mid-point

Last Answer : (c) At the fixed end

Choose the wrong statement (A) Fluids are capable of flowing (B) Fluids conform to the shape of the containing vessels (C) When in equilibrium, fluids cannot sustain tangential forces (D) When in equilibrium, fluids can sustain shear forces

Description : Choose the wrong statement (A) Fluids are capable of flowing (B) Fluids conform to the shape of the containing vessels (C) When in equilibrium, fluids cannot sustain tangential forces (D) When in equilibrium, fluids can sustain shear forces

Last Answer : Answer: Option D

The normal stress is the same in all directions at a point in a fluid, when the fluid is (A) Non-viscous (B) Incompressible (C) Both (A) and (B) (D) Having no motion of one fluid layer relative to the other

Description : The normal stress is the same in all directions at a point in a fluid, when the fluid is (A) Non-viscous (B) Incompressible (C) Both (A) and (B) (D) Having no motion of one fluid layer relative to the other

Last Answer : (D) Having no motion of one fluid layer relative to the other

16. The shear stress-strain graph for a Non-Newtonian fluid is a curve. A) Correct B) Incorrect

Description : 16. The shear stress-strain graph for a Non-Newtonian fluid is a curve. A) Correct B) Incorrect

Last Answer : A

According to Newton's law of viscosity, the shear stress on a layer of a fluid is __________ to the rate of shear strain. (A) Equal to (B) Directly proportional (C) Inversely proportional (D) None of these

Description : According to Newton's law of viscosity, the shear stress on a layer of a fluid is __________ to the rate of shear strain. (A) Equal to (B) Directly proportional (C) Inversely proportional (D) None of these

Last Answer : Answer: Option B

Bulk modulus of a fluid is the ratio of (A) Shear stress to shear strain (B) Increase in volume to the viscosity of fluid (C) Increase in pressure to the volumetric strain (D) Critical velocity to the viscosity of fluid

Description : Bulk modulus of a fluid is the ratio of (A) Shear stress to shear strain (B) Increase in volume to the viscosity of fluid (C) Increase in pressure to the volumetric strain (D) Critical velocity to the viscosity of fluid

Last Answer : Answer: Option C

The shear stress-strain graph for a Newtonian fluid is a (A) Straight line (B) Parabolic curve (C) Hyperbolic curve (D) Elliptical

Description : The shear stress-strain graph for a Newtonian fluid is a (A) Straight line (B) Parabolic curve (C) Hyperbolic curve (D) Elliptical

Last Answer : Answer: Option A

In a static fluid (A) Resistance to shear stress is small (B) Fluid pressure is zero (C) Linear deformation is small (D) Only normal stresses can exist

Description : In a static fluid (A) Resistance to shear stress is small (B) Fluid pressure is zero (C) Linear deformation is small (D) Only normal stresses can exist

Last Answer : Answer: Option D

A fluid in equilibrium can't sustain (A) Tensile stress (B) Compressive stress (C) Shear stress (D) Bending stress

Description : A fluid in equilibrium can't sustain (A) Tensile stress (B) Compressive stress (C) Shear stress (D) Bending stress

Last Answer : Answer: Option C

Consider the following statements in respect of steady laminar flow through a circular pipe: 1. Shear stress is zero on the central axis of the pipe 2. Discharge varies directly with the viscosity of the fluid 3. Velocity is maximum at the centre of the pipe. 4. Hydraulic gradient varies as the square of the mean velocity of flow. Which of these statements are correct? (a) 1, 2 , 3 & 4 (b) 1 & 3 only (c) 2 & 4 only (d)3 & 4 only

Description : Consider the following statements in respect of steady laminar flow through a circular pipe: 1. Shear stress is zero on the central axis of the pipe 2. Discharge varies directly with the viscosity of the fluid 3. Velocity is maximum at the ... 2 , 3 & 4 (b) 1 & 3 only (c) 2 & 4 only (d)3 & 4 only

Last Answer : (b) 1 & 3 only

When a bar is subjected to increase in temperature and its deformation is prevented, the stress induced in the bar is (a) Tensile (b) Compressive (c) Shear (d) None of the above

Description : When a bar is subjected to increase in temperature and its deformation is prevented, the stress induced in the bar is (a) Tensile (b) Compressive (c) Shear (d) None of the above

Last Answer : (b) Compressive

When a bar is subjected to a change of temperature and its longitudinal deformation is prevented, the stress induced in the bar is (a) Tensile (b) Compressive (c) Shear (d) Temperature

Description : When a bar is subjected to a change of temperature and its longitudinal deformation is prevented, the stress induced in the bar is (a) Tensile (b) Compressive (c) Shear (d) Temperature

Last Answer : (d) Temperature

The shear force on a simply supported beam is proportional to (A) Displacement of the neutral axis (B) Sum of the forces (C) Sum of the transverse forces (D) Algebraic sum of the transverse forces of the section

Description : The shear force on a simply supported beam is proportional to (A) Displacement of the neutral axis (B) Sum of the forces (C) Sum of the transverse forces (D) Algebraic sum of the transverse forces of the section

Last Answer : (D) Algebraic sum of the transverse forces of the section

Pick up the correct statement from the following: (A) For thin structures subjected to wetting and drying, the water cement ratio should be 0.45 (B) For mass concrete structures subjected to wetting and drying, the water ratio should be 0.55 (C) For thin structures which remain continuously under water, the water-cement ratio by weight should be 0.55 (D) All the above

Description : Pick up the correct statement from the following: (A) For thin structures subjected to wetting and drying, the water cement ratio should be 0.45 (B) For mass concrete structures subjected to wetting and ... under water, the water-cement ratio by weight should be 0.55 (D) All the above

Last Answer : Answer: Option D