Differentiate between two and three wire control.

Differentiate between two and three wire control.
by

1 Answer

Answer :

Two wire control: 
Three wire control
It provides low voltage release
It provides low voltage protection
IT will automatically start when power resumes
IT will automatically start when power resumes
It does not have sealing contact
It has sealing contact
It is not safe for operator
It is safe for operator
It is used for submersible pump motors which are located at remote locations 
Its is used for industrial control panels where safety is important 
by

Related questions

Differentiate between two-wire and three-wire control

Description : Differentiate between two-wire and three-wire control

Last Answer : Two-Wire Control  Three-Wire Control 1 The control component offers only two-wires for its connection in control circuit. The control components offer threewires for their connection in control ... using starter. The safe starting ensures the Novolt protection.  4

Differentiate between control wiring and power wiring.

Description : Differentiate between control wiring and power wiring.

Last Answer : Control Wiring Power Wiring Used for connecting control circuit which consists of input devices such as push buttons, selector switches, proximity switches, indicating lamps etc. Used for ... Conductor selections for power wiring is based on rating of load and overload capacity.

Differentiate air fuel ratio between carburetted engine and electronic fuel injection engines control system.

Description : Differentiate air fuel ratio between carburetted engine and electronic fuel injection engines control system.

Last Answer : Sr. No. Carburetted engine Electronic Fuel Injection (EFI) engine 1 Fuel atomization depends upon velocity of air in the venturi. Atomization of fuel is independent of cranking ... occurs in carbureted engine. Equal quantity of fuel is supplied to port for each cylinder

Differentiate between power and control wiring

Description : Differentiate between power and control wiring

Last Answer : Power wiring Control wiring 1 Used for connecting load to main power supply through appropriate switchgear and protecting devices such as overload relay contacts Used for ... can be used for connecting control circuit as control circuit does not carry higher current.

Describe the importance of three wire and four wire configuration for RTD with suitable circuit diagram.

Description : Describe the importance of three wire and four wire configuration for RTD with suitable circuit diagram.

Last Answer : Three wire RTD: Four wire RTD: Three wire configurations is used to help the circuit compensate for lead wire resistance, and thus provide a truer indication of the measured ... the leads. To get the optimum performance, it is generally best to specify the RTD configuration. 

In a three phase half wave rectifier feeding resistive load, if the input source is a three phase 4 wire system

Description : In a three phase half wave rectifier feeding resistive load, if the input source is a three phase 4 wire system and line to line voltage is 100 V. The supply frequency is 400 Hz. The ripple frequency at the output is: (1) 400 Hz (2) 800 Hz (3) 1200 Hz (4) None of these

Last Answer : In a three phase half wave rectifier feeding resistive load, if the input source is a three phase 4 wire system and line to line voltage is 100 V. The supply frequency is 400 Hz. The ripple frequency at the output is: 1200 Hz

In a 3-phase 4-wire distribution system three unbalanced but equal magnitude impedances are connected...

Description : In a 3-phase 4-wire distribution system three unbalanced but equal magnitude impedances are connected between respective lines and neutral. The magnitude of current in the neutral conductor for RYB and RBY phase sequences ... ) zero (B) same (C) different (D) same in magnitude but differs in phase.

Last Answer : In a 3-phase 4-wire distribution system three unbalanced but equal magnitude impedances are connected between respective lines and neutral. The magnitude of current in the neutral conductor for RYB and RBY phase sequences are different 

In a certain three -wire Y -connected generator, the phase voltages are 2 kV. The magnitudes of the line...

Description : In a certain three -wire Y -connected generator, the phase voltages are 2 kV. The magnitudes of the line voltages will be: A. 2,000 V B. 6,000 V C. 666 V D. 3,464 V

Last Answer : In a certain three -wire Y -connected generator, the phase voltages are 2 kV. The magnitudes of the line voltages will be: 3,464 V

Differentiate between N-channel and P-channel J-FET.

Description : Differentiate between N-channel and P-channel J-FET.

Last Answer : N-Channel JFET P-Channel JFET 1.The current conduction takes place due to electrons 1.The current conduction takes place due to holes. 2.Its switching speed and cut off ... It is most widely used in circuit applications 5.It is comparatively less used in circuit applications

Differentiate between RAM & ROM in PLC memory

Description : Differentiate between RAM & ROM in PLC memory

Last Answer : RAM ROM Random access memory Read Only memory Used for storing temporary data Used for storing fixed data such as programs Data is lost when power is removed Data is retained in case of power loss  Read write speed is quite faster Write operation is slow

Differentiate between pneumatic and hydraulic system.

Description : Differentiate between pneumatic and hydraulic system. 

Last Answer : Pneumatic System Hydraulic System 1 Pneumatic system uses gas for power transmission, after compression and it is used as medium for carrying out mechanical work. ... : In industrial applications, air conditioners Applications: In petrochemical industries, oil refineries.

Differentiate between mass flow rate and volumetric flow rate.

Description : Differentiate between mass flow rate and volumetric flow rate. 

Last Answer : Volumetric flow rate Mass flow rate Volumetric flow is the measure of a substance moving through a device over time. Mass flow rate is the amount of Mass moving through an instrument over ... = Velocity of flowing fluid x Area. Mass flow rate = volumetric flow rate x density

Differentiate between positive and negative feedback.

Description : Differentiate between positive and negative feedback.

Last Answer : PARAMETER POSITIVE FEEDBACK NEGATIVE FEEDBACK Overall phase shift 0° or 360° 180° Feedback and input signal Are in phase Are out of phase Input signal ... Increases Input impedance Decreases Increases Output impedance Increases Decreases

Differentiate between spontaneous and stimulated emission of light with diagram.

Description : Differentiate between spontaneous and stimulated emission of light with diagram.

Last Answer : Spontaneous emission Stimulated emission Excited atoms comes to ground state on its own accord Excited atoms comes to ground state after interaction with incident photon. Radiations are in random ... Number of photons emitted are less Number of photons emitted are more

Differentiate between isotopes and isobars.

Description : Differentiate between isotopes and isobars.

Last Answer : Isotopes Isobars These are the atoms of same element having same atomic number but different atomic mass number. These are the atoms of different elements having different atomic number but same atomic mass ... are different e.g. 11H, 12H, 13H e.g. 1840Ar, 1940K, 2040Ca

Differentiate between thermosetting and thermo-softening plastics.

Description : Differentiate between thermosetting and thermo-softening plastics. 

Last Answer : Thermosetting Thermo-softening 1. The plastics who possess three dimensional complicated structure with cross linkages are called as thermo setting plastics 1. The plastics who possess ... , Urea formaldehyde, Silicon plastic 11. Examples- Polythene, Polystyrene, PVC, Teflon 

Differentiate between orbits and orbitals.

Description : Differentiate between orbits and orbitals. 

Last Answer : Orbits Orbitals 1. It is fixed path along which the electrons revolve around the nucleus. 1. It is the region in the space where the probability of finding an electron is maximum. 2. Orbits are ...   5. The number of orbitals relative to energy level are n2=1, 4, 9, 16 etc. 

Give any three importance of dosage forms. Differentiate between Mouthwash and Gargle.

Description : Give any three importance of dosage forms. Differentiate between Mouthwash and Gargle.

Last Answer : Importance of dosage forms : 1. To protect drug substances from oxidation, hydrolysis, reduction etc.eg. coated tablets, sealed ampoules etc. 2. To protect the drug from destructive effect of ... mouth wash, Listrin. 6. Examples: Phenol gargle, potassium chlorate gargle, Betadine.