The deflection of any rectangular beam simply supported, is (A) Directly proportional to its weight (B) Inversely proportional to its width (C) Inversely proportional to the cube of its depth (D) Directly proportional to the cube of its length

The deflection of any rectangular beam simply supported, is
(A) Directly proportional to its weight
(B) Inversely proportional to its width
(C) Inversely proportional to the cube of its depth
(D) Directly proportional to the cube of its length
by

1 Answer

Answer :

(C) Inversely proportional to the cube of its depth
by

Related questions

If the width b and depth d of a beam simply supported with a central load are interchanged, the deflection at the centre of the beam will be changed in the ratio of (A) b/d (B) d/b (C) (d/b)2 (D) (b/d)

Description : If the width b and depth d of a beam simply supported with a central load are interchanged, the  deflection at the centre of the beam will be changed in the ratio of  (A) b/d (B) d/b (C) (d/b)2 (D) (b/d)

Last Answer : (D) (b/d)2

A simply supported uniform rectangular bar breadth b, depth d and length L carries an isolated load W at its mid-span. The same bar experiences an extension e under same tensile load. The ratio of the maximum deflection to the elongation, is (A) L/d (B) L/2d (C) (L/2d)² (D) (L/3d)²

Description : A simply supported uniform rectangular bar breadth b, depth d and length L carries an isolated  load W at its mid-span. The same bar experiences an extension e under same tensile load. The  ratio of the maximum deflection to the ... (A) L/d (B) L/2d (C) (L/2d)² (D) (L/3d)²

Last Answer : (C) (L/2d)

A simply supported beam is of rectangular section.It carries a uniformly distributed load over the whole span.The deflection at the centre is y.If the depth of beam is doubled ,the deflection at the centre would be a.2y b.4y c.y/2 d.y/8.

Description : A simply supported beam is of rectangular section.It carries a uniformly distributed load over the whole span.The deflection at the centre is y.If the depth of beam is doubled ,the deflection at the centre would be a.2y b.4y c.y/2 d.y/8.

Last Answer : d.y/8.

A uniformly distributed load of 20 kN/m acts on a simply supported beam of rectangular cross section of width 20 mm and depth 60 mm. What is the maximum bending stress acting on the beam of 5m? a. 5030 Mpa b. 5208 Mpa c. 6600 Mpa d. Insufficient data

Description : A uniformly distributed load of 20 kN/m acts on a simply supported beam of rectangular cross section of width 20 mm and depth 60 mm. What is the maximum bending stress acting on the beam of 5m? a. 5030 Mpa b. 5208 Mpa c. 6600 Mpa d. Insufficient data

Last Answer : b. 5208 Mpa

The ratio of the length and depth of a simply supported rectangular beam which experiences maximum bending stress equal to tensile stress, due to same load at its mid span, is (A) 1/2 (B) 2/3 (C) 1/4 (D) 1/3

Description : The ratio of the length and depth of a simply supported rectangular beam which experiences  maximum bending stress equal to tensile stress, due to same load at its mid span, is  (A) 1/2  (B) 2/3  (C) 1/4  (D) 1/3

Last Answer : (B) 2/3 

The width of a beam of uniform strength having a constant depth d length L, simply supported at the ends with a central load W is (A) 2WL/3fd² (B) 3WL/2fd² (C) 2fL/3Wd 4 (D) 3fL²/2Wd

Description : The width of a beam of uniform strength having a constant depth d length L, simply supported at the ends with a central load W is (A) 2WL/3fd² (B) 3WL/2fd² (C) 2fL/3Wd 4 (D) 3fL²/2Wd

Last Answer : (B) 3WL/2fd²

If the width of a simply supported beam carrying an isolated load at its centre is doubled, the deflection of the beam at the centre is changed by (A) 1/2 (B) 1/8 (C) 2 (D) 8

Description : If the width of a simply supported beam carrying an isolated load at its centre is doubled, the deflection of the beam at the centre is changed by (A) 1/2 (B) 1/8 (C) 2 (D) 8

Last Answer : (A) 1/2

If the width of a simply supported beam carrying an isolated load at its centre is doubled, the deflection of the beam at the centre is changed by (A) 2 times (B) 4 times (C) 8 times (D) 1/2 times

Description : If the width of a simply supported beam carrying an isolated load at its centre is doubled, the deflection of the beam at the centre is changed by (A) 2 times (B) 4 times (C) 8 times (D) 1/2 times

Last Answer : (C) 8 times

A simply supported beam carries a uniformly distributed load over the whole span.The deflection at the centre is y.If the distributed load per unit length is doubled and also depth of beam is doubled ,then the deflection at the centre would be a.2y b.4y c.y/2 d.y/4.

Description : A simply supported beam carries a uniformly distributed load over the whole span.The deflection at the centre is y.If the distributed load per unit length is doubled and also depth of beam is doubled ,then the deflection at the centre would be a.2y b.4y c.y/2 d.y/4.

Last Answer : d.y/4.

If the depth of a simply supported beam carrying an isolated load at its centre, is doubled, the deflection of the beam at the centre will be changed by a factor of (A) 2 (B) 1/2 (C) 8 (D) 1/8

Description : If the depth of a simply supported beam carrying an isolated load at its centre, is doubled, the deflection of the beam at the centre will be changed by a factor of (A) 2 (B) 1/2 (C) 8 (D) 1/8

Last Answer : (D) 1/8

A 8 metre long simply supported rectangular beam which carries a distributed load 45 kg/m. experiences a maximum fibre stress 160 kg/cm2 . If the moment of inertia of the beam is 640 cm4 , the overall depth of the beam is (A) 10 cm (B) 12 cm (C) 15 cm (D) 18 cm

Description : A 8 metre long simply supported rectangular beam which carries a distributed load 45 kg/m. experiences a maximum fibre stress 160 kg/cm2 . If the moment of inertia of the beam is 640 cm4 , the overall depth of the beam is (A) 10 cm (B) 12 cm (C) 15 cm (D) 18 cm

Last Answer : (A) 10 cm

For a simply supported beam of span 15 m, the minimum effective depth to satisfy the vertical deflection limits should be (A) 600 mm (B) 750 mm (C) 900 mm (D) More than 1 m

Description : For a simply supported beam of span 15 m, the minimum effective depth to satisfy the vertical deflection limits should be (A) 600 mm (B) 750 mm (C) 900 mm (D) More than 1 m

Last Answer : Answer: Option B

Basic value of span to depth ratio for simply supported beam to control deflection is [ A ] 7 [ B ] 20 [ C ] 26 [ D ] 35

Description : Basic value of span to depth ratio for simply supported beam to control deflection is [ A ] 7 [ B ] 20 [ C ] 26 [ D ] 35

Last Answer : [ B ] 20

A beam of uniform rectangular section 200 mm wide and 300mm deep is simply supported at its ends.It carries a uniformly distributed load of 9KN/m run over the entire span of 5m.If E=1×104 N/mm2, what is the maximum deflection? a.14.26 mm b.17.28 mm c.18.53 mm d.16.27 mm.

Description : A beam of uniform rectangular section 200 mm wide and 300mm deep is simply supported at its ends.It carries a uniformly distributed load of 9KN/m run over the entire span of 5m.If E=1×104 N/mm2, what is the maximum deflection? a.14.26 mm b.17.28 mm c.18.53 mm d.16.27 mm.

Last Answer : d.16.27 mm.

In case of a simply supported rectangular beam of span L and loaded with a central load W, the length of elasto-plastic zone of the plastic hinge, is (A) L/2 (B) L/3 (C) L/4 (D) L/5

Description : In case of a simply supported rectangular beam of span L and loaded with a central load W, the  length of elasto-plastic zone of the plastic hinge, is  (A) L/2  (B) L/3  (C) L/4  (D) L/5 

Last Answer : (B) L/3 

The maximum deflection of a simply supported beam of length L with a central load W, is (A) WL²/48EI (B) W²L/24EI (C) WL3 /48EI (D) WL²/8EI

Description : The maximum deflection of a simply supported beam of length L with a central load W, is (A) WL²/48EI (B) W²L/24EI (C) WL3 /48EI (D) WL²/8EI

Last Answer : (C) WL3 /48EI

The intensity of pressure at any point, in a liquid, is (A) Directly proportional to the area of the vessel containing liquid (B) Directly proportional to the depth of liquid from the surface (C) Directly proportional to the length of the vessel containing liquid (D) Inversely proportional to the depth of liquid from the surface

Description : The intensity of pressure at any point, in a liquid, is (A) Directly proportional to the area of the vessel containing liquid (B) Directly proportional to the depth of liquid from the ... length of the vessel containing liquid (D) Inversely proportional to the depth of liquid from the surface

Last Answer : Answer: Option B

A simply supported beam 6 m long and of effective depth 50 cm, carries a uniformly distributed load 2400 kg/m including its self weight. If the lever arm factor is 0.85 and permissible tensile stress of steel is 1400 kg/cm2 , the area of steel required, is (A) 14 cm(B) 15 cm2(C) 16 cm2(D) 17 cm

Description : A simply supported beam 6 m long and of effective depth 50 cm, carries a uniformly distributed load 2400 kg/m including its self weight. If the lever arm factor is 0.85 and permissible tensile stress of steel is 1400 kg/cm2 ... area of steel required, is (A) 14 cm (B) 15 cm2 (C) 16 cm2 (D) 17 cm

Last Answer : Answer: Option C

δ = (W a 2 b 2 ) / (3 EIL) is the value of deflection for ______ A. simply supported beam which has central point load B. simply supported beam which has eccentric point load C. simply supported beam which has U.D.L. point load per unit length D. fixed beam which has central point load

Description : δ = (W a 2 b 2 ) / (3 EIL) is the value of deflection for ______ A. simply supported beam which has central point load B. simply supported beam which has eccentric point load C. simply supported beam which has U.D.L. point load per unit length D. fixed beam which has central point load

Last Answer : B. simply supported beam which has eccentric point load

δ = (W a 2 b 2 ) / (3 EIl) is the value of deflection for ______ a. simply supported beam which has central point load b. simply supported beam which has eccentric point load c. simply supported beam which has U.D.L. point load per unit length d. fixed beam which has central point load

Description : δ = (W a 2 b 2 ) / (3 EIl) is the value of deflection for ______ a. simply supported beam which has central point load b. simply supported beam which has eccentric point load c. simply supported beam which has U.D.L. point load per unit length d. fixed beam which has central point load

Last Answer : b. simply supported beam which has eccentric point load

A simply supported beam carries uniformly distributed load of 20 kN/m over the length of 5 m. If flexural rigidity is 30000 kN.m2, what is the maximum deflection in the beam? a. 5.4 mm b. 1.08 mm c. 6.2 mm d. 8.6 mm

Description : A simply supported beam carries uniformly distributed load of 20 kN/m over the length of 5 m. If flexural rigidity is 30000 kN.m2, what is the maximum deflection in the beam? a. 5.4 mm b. 1.08 mm c. 6.2 mm d. 8.6 mm

Last Answer : a. 5.4 mm

The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of 4 tonnes at the centre. The maximum stress in the bottom most fibre at the mid span section, is (A) 13.33 kg/cm2 tensile (B) 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive

Description : The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of ... 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive

Last Answer : (C) 26.67 kg/cm2 tensile

The discharge over a rectangular notch is (A) Inversely proportional to H 3/2 (B) Directly proportional to H 3/2 (C) Inversely proportional to H 5/2 (D) Directly proportional to H 5/2

Description : The discharge over a rectangular notch is (A) Inversely proportional to H 3/2 (B) Directly proportional to H 3/2 (C) Inversely proportional to H 5/2 (D) Directly proportional to H 5/2

Last Answer : Answer: Option B

A simply supported beam deflects by 5 mm when it is subjected to a concentrated load of 10 kN at its centre. What will be deflection in a 1/10 model of the beam if the model is subjected to a 1 kN load at its centre? (A) 5 mm (B) 0.5 mm (C) 0.05 mm (D) 0.005 mm

Description : A simply supported beam deflects by 5 mm when it is subjected to a concentrated load of 10 kN at its centre. What will be deflection in a 1/10 model of the beam if the model is subjected to a 1 kN load at its centre? (A) 5 mm (B) 0.5 mm (C) 0.05 mm (D) 0.005 mm

Last Answer : (A) 5 mm

Maximum deflection of a (A) Cantilever beam carrying a concentrated load W at its free end is WL3 /3EI (B) Simply supported beam carrying a concentrated load W at mid-span is WL3 /48EI (C) Cantilever beam, carrying a uniformly distributed load over span is WL3 /8EI (D) All the above

Description : Maximum deflection of a (A) Cantilever beam carrying a concentrated load W at its free end is WL3 /3EI (B) Simply supported beam carrying a concentrated load W at mid-span is WL3 /48EI (C) Cantilever beam, carrying a uniformly distributed load over span is WL3 /8EI (D) All the above

Last Answer : (D) All the above

What is the distance away from midspan of a plastic hinge if developing in a simply supported beam of rectangular cross-section and span 6 m, subjected to a point load at the centre? (a) Zero (b) 1 m (c) 2 m (d) 3 m

Description : What is the distance away from midspan of a plastic hinge if developing in a simply supported beam of rectangular cross-section and span 6 m, subjected to a point load at the centre? (a) Zero (b) 1 m (c) 2 m (d) 3 m

Last Answer : (a) Zero

A simply supported rectangular beam is uniformly loaded and is prestressed. The tendon provided for prestressing should be (a) Straight, above centroidal axis (b) Straight, below centroidal axis (c) parabolic, with convexity upward (d) Parabolic, with convexity downward

Description : A simply supported rectangular beam is uniformly loaded and is prestressed. The tendon provided for prestressing should be (a) Straight, above centroidal axis (b) Straight, below centroidal axis (c) parabolic, with convexity upward (d) Parabolic, with convexity downward

Last Answer : (d) Parabolic, with convexity downward

The maximum deflection of a simply supported beam of span L, carrying an isolated load at the centre of the span; flexural rigidity being EI, is (A) WL3 /3EL (B) WL3 /8EL (C) WL3 /24EL (D) WL3 /48EL

Description : The maximum deflection of a simply supported beam of span L, carrying an isolated load at the  centre of the span; flexural rigidity being EI, is  (A) WL3 /3EL (B) WL3 /8EL (C) WL3 /24EL (D) WL3 /48EL

Last Answer : (D) WL3 /48EL

The maximum deflection of (A) A simply supported beam carrying a uniformly increasing load from either end and having the apex at the mid span is WL3 /60EI (B) A fixed ended beam carrying a distributed load over the span is WL3 /384EI (C) A fixed ended beam carrying a concentrated load at the mid span is WL3 /192EI (D) All the above

Description : The maximum deflection of  (A) A simply supported beam carrying a uniformly increasing load from either end and having  the apex at the mid span is WL3 /60EI (B) A fixed ended beam ... ended beam carrying a concentrated load at the mid span is WL3 /192EI (D) All the above 

Last Answer : (D) All the above 

An increase in temperature on the top fibre of a simply supported beam will cause (a) Downward deflection (b) Upward deflection (c) No deflection (d) Angular rotation about neutral axis

Description : An increase in temperature on the top fibre of a simply supported beam will cause (a) Downward deflection (b) Upward deflection (c) No deflection (d) Angular rotation about neutral axis

Last Answer : Upward deflection

A cantilever beam rectangular in cross-section is subjected to an isolated load at its free end. If the width of the beam is doubled, the deflection of the free end will be changed in the ratio of (A) 8 (B) 1/8 (C) 1/2 (D) 3

Description : A cantilever beam rectangular in cross-section is subjected to an isolated load at its free end. If the  width of the beam is doubled, the deflection of the free end will be changed in the ratio of  (A) 8  (B) 1/8  (C) 1/2  (D) 3

Last Answer : (C) 1/2 

The shear force on a simply supported beam is proportional to (A) Displacement of the neutral axis (B) Sum of the forces (C) Sum of the transverse forces (D) Algebraic sum of the transverse forces of the section

Description : The shear force on a simply supported beam is proportional to (A) Displacement of the neutral axis (B) Sum of the forces (C) Sum of the transverse forces (D) Algebraic sum of the transverse forces of the section

Last Answer : (D) Algebraic sum of the transverse forces of the section

Pick up the incorrect statement from the following. The super-elevation on roads is (A) Directly proportional to width of pavement (B) Directly proportional to velocity of vehicles (C) Inversely proportional to acceleration due to gravity (D) Inversely proportional to the radius of curvature

Description : Pick up the incorrect statement from the following. The super-elevation on roads is (A) Directly proportional to width of pavement (B) Directly proportional to velocity of vehicles (C) Inversely proportional to acceleration due to gravity (D) Inversely proportional to the radius of curvature

Last Answer : Answer: Option B

For normal cases, stiffness of a simply supported beam is satisfied if the ratio of its span to its overall depth does not exceed (A) 10 (B) 15 (C) 20 (D) 25

Description : For normal cases, stiffness of a simply supported beam is satisfied if the ratio of its span to its overall depth does not exceed (A) 10 (B) 15 (C) 20 (D) 25

Last Answer : Answer: Option C

Stress in a beam due to simple bending, is (A) Directly proportional (B) Inversely proportional (C) Curvilinearly related (D) None of these

Description : Stress in a beam due to simple bending, is  (A) Directly proportional  (B) Inversely proportional  (C) Curvilinearly related  (D) None of these 

Last Answer : (A) Directly proportional 

The section modulus of a rectangular section is proportional to (A) Area of the section (B) Square of the area of the section (C) Product of the area and depth (D) Product of the area and width

Description : The section modulus of a rectangular section is proportional to  (A) Area of the section  (B) Square of the area of the section  (C) Product of the area and depth  (D) Product of the area and width

Last Answer : (A) Area of the section

The intensity of pressure at any point, in a liquid, is __________ to the depth of liquid from the surface. (A) Equal (B) Directly proportional (C) Inversely proportional (D) None of these

Description : The intensity of pressure at any point, in a liquid, is __________ to the depth of liquid from the surface. (A) Equal (B) Directly proportional (C) Inversely proportional (D) None of these

Last Answer : Answer: Option B

For the design of a simply supported T-beam the ratio of the effective span to the overall depth of the beam is limited to (A) 10 (B) 15 (C) 20 (D) 25

Description : For the design of a simply supported T-beam the ratio of the effective span to the overall depth of the beam is limited to (A) 10 (B) 15 (C) 20 (D) 25

Last Answer : Answer: Option C

If the ratio of the span to the overall depth does not exceed 10, the stiffness of the beam will ordinarily be satisfactory in case of a (A) Simply supported beam (B) Continuous beam (C) Cantilever beam (D) None of these

Description : If the ratio of the span to the overall depth does not exceed 10, the stiffness of the beam will ordinarily be satisfactory in case of a (A) Simply supported beam (B) Continuous beam (C) Cantilever beam (D) None of these

Last Answer : Answer: Option C

A rolled steel joist is simply supported at its ends and carries a uniformly distributed load which causes a maximum deflection of 10 mm and slope at the ends of 0.002 radian. The length of the joist will be, (A) 10 m (B) 12 m (C) 14 m (D) 16 m

Description : A rolled steel joist is simply supported at its ends and carries a uniformly distributed load which  causes a maximum deflection of 10 mm and slope at the ends of 0.002 radian. The length of the  joist will be,  (A) 10 m  (B) 12 m  (C) 14 m  (D) 16 m 

Last Answer : (D) 16 m 

A uniform girder simply supported at its ends is subjected to a uniformly distributed load over its entire length and is propped at the centre so as to neutralise the deflection. The net B.M. at the centre will be (A) WL (B) WL/8 (C) WL/24 (D) WL/32

Description : A uniform girder simply supported at its ends is subjected to a uniformly distributed load over its entire length and is propped at the centre so as to neutralise the deflection. The net B.M. at the centre will be (A) WL (B) WL/8 (C) WL/24 (D) WL/32

Last Answer : (D) WL/32

For a strongest rectangular beam cut from a circular log, the ratio of the width and depth, is (A) 0.303 (B) 0.404 (C) 0.505 (D) 0.707

Description : For a strongest rectangular beam cut from a circular log, the ratio of the width and depth, is  (A) 0.303  (B) 0.404  (C) 0.505  (D) 0.707 

Last Answer : (D) 0.707 

A beam 3m long simply supported at its ends ,is carrying a point load W at the centre.If the slope at the ends of the beam should not exceed 10,find the deflection at the centre of beam? a.18.41 mm b.13.45 mm c.17.45 mm d.21.67 mm.

Description : A beam 3m long simply supported at its ends ,is carrying a point load W at the centre.If the slope at the ends of the beam should not exceed 10,find the deflection at the centre of beam? a.18.41 mm b.13.45 mm c.17.45 mm d.21.67 mm.

Last Answer : c.17.45 mm

State cable profile in simply supported rectangular beam section.

Description : State cable profile in simply supported rectangular beam section.

Last Answer : Cabe profile: In a prestressed concrete member, external type of loads is balanced by transverse component of suitable cable profile, on effect of loading the net deformation increases the stress, strain and length of the tendon, extension of tendon, increase in strain, increase in stress.

For the same span and loads fixed beam in comparison with simply supported beams has a. lesser value of maximum deflection b. more value of maximum deflecction c.twice the value of maximum deflecction d.same value of maximum deflecction

Description : For the same span and loads fixed beam in comparison with simply supported beams has a. lesser value of maximum deflection b. more value of maximum deflecction c.twice the value of maximum deflecction d.same value of maximum deflecction

Last Answer : a. lesser value of maximum deflection

Which of the following statements is/are true for a simply supported beam? a. Deflection at supports in a simply supported beam is maximum. b.Deflection is maximum at a point where slope is zero . c. Slope is minimum at supports in a simply supported beam. d. All of the above.

Description : Which of the following statements is/are true for a simply supported beam? a. Deflection at supports in a simply supported beam is maximum. b.Deflection is maximum at a point where slope is zero . c. Slope is minimum at supports in a simply supported beam. d. All of the above

Last Answer : b.Deflection is maximum at a point where slope is zero .

Deflection of a simply supported beam when subjected to central point load is given as ________ a. (Wl /16 EI) b. (Wl2/16 EI) c. (Wl3/48 EI) d. (5Wl4/ 384EI)

Description : Deflection of a simply supported beam when subjected to central point load is given as ________ a. (Wl /16 EI) b. (Wl2/16 EI) c. (Wl3/48 EI) d. (5Wl4/ 384EI)

Last Answer : c. (Wl3/48 EI)

The Reynold's number of a ship is __________ to its velocity and length. (A) Directly proportional (B) Inversely proportional (C) Square root of velocity (D) None of these

Description : The Reynold's number of a ship is __________ to its velocity and length. (A) Directly proportional (B) Inversely proportional (C) Square root of velocity (D) None of these

Last Answer : Answer: Option A

The ratio of the length and diameter of a simply supported uniform circular beam which experiences maximum bending stress equal to tensile stress due to same load at its mid span, is (A) 1/8 (B) 1/4 (C) 1/2 (D) 1/3

Description : The ratio of the length and diameter of a simply supported uniform circular beam which  experiences maximum bending stress equal to tensile stress due to same load at its mid span, is  (A) 1/8  (B) 1/4  (C) 1/2  (D) 1/3 

Last Answer : (C) 1/2 

The ratio of the maximum deflections of a simply supported beam with a central load W and of a cantilever of same length and with a load W at its free end, is (A) 1/8 (B) 1/10 (C) 1/12 (D) 1/16

Description : The ratio of the maximum deflections of a simply supported beam with a central load W and of a  cantilever of same length and with a load W at its free end, is  (A) 1/8  (B) 1/10  (C) 1/12  (D) 1/16 

Last Answer : (D) 1/16