An increase in temperature on the top fibre of a simply supported beam will cause (a) Downward deflection (b) Upward deflection (c) No deflection (d) Angular rotation about neutral axis

An increase in temperature on the top fibre of a simply supported beam will cause
(a) Downward deflection
(b) Upward deflection
(c) No deflection
(d) Angular rotation about neutral axis
by

2 Answers

Answer :

(b) Upward deflection
by

Answer :

Upward deflection
by

Related questions

A simply supported rectangular beam is uniformly loaded and is prestressed. The tendon provided for prestressing should be (a) Straight, above centroidal axis (b) Straight, below centroidal axis (c) parabolic, with convexity upward (d) Parabolic, with convexity downward

Description : A simply supported rectangular beam is uniformly loaded and is prestressed. The tendon provided for prestressing should be (a) Straight, above centroidal axis (b) Straight, below centroidal axis (c) parabolic, with convexity upward (d) Parabolic, with convexity downward

Last Answer : (d) Parabolic, with convexity downward

When a simply supported beam is loaded with a point load at the centre, the maximum tensile stress is developed on the (a) Top fibre (b) Bottom fibre (c) Neutral axis (d) None of these

Description : When a simply supported beam is loaded with a point load at the centre, the maximum tensile stress is developed on the (a) Top fibre (b) Bottom fibre (c) Neutral axis (d) None of these

Last Answer : (b) Bottom fibre

Due to shrinkage stresses, a simply supported beam having reinforcement only at bottom tends to (A) Deflect downward (B) Deflect upward (C) Deflect downward or upward (D) None of the above

Description : Due to shrinkage stresses, a simply supported beam having reinforcement only at bottom tends to (A) Deflect downward (B) Deflect upward (C) Deflect downward or upward (D) None of the above

Last Answer : Answer: Option A

Along the neutral axis of a simply supported beam (A) Fibres do not undergo strain (B) Fibres undergo minimum strain (C) Fibres undergo maximum strain (D) None of these

Description : Along the neutral axis of a simply supported beam  (A) Fibres do not undergo strain  (B) Fibres undergo minimum strain  (C) Fibres undergo maximum strain  (D) None of these

Last Answer : (A) Fibres do not undergo strain 

The shear force on a simply supported beam is proportional to (A) Displacement of the neutral axis (B) Sum of the forces (C) Sum of the transverse forces (D) Algebraic sum of the transverse forces of the section

Description : The shear force on a simply supported beam is proportional to (A) Displacement of the neutral axis (B) Sum of the forces (C) Sum of the transverse forces (D) Algebraic sum of the transverse forces of the section

Last Answer : (D) Algebraic sum of the transverse forces of the section

In a simply supported reinforced concrete beam, the reinforcement is placed. (a) Above the neutral axis (b) Below the neutral axis (c) At the neutral axis (d) None of these

Description : In a simply supported reinforced concrete beam, the reinforcement is placed. (a) Above the neutral axis (b) Below the neutral axis (c) At the neutral axis (d) None of these

Last Answer : (b) Below the neutral axis

If the loading on a pre-stressed rectangular beam, is uniformly distributed, the tendon to be provided should be. (A) Straight below centroidal axis (B) Parabolic with convexity downward (C) Parabolic with convexity upward (D) Straight above centroidal axis

Description : If the loading on a pre-stressed rectangular beam, is uniformly distributed, the tendon to be provided should be. (A) Straight below centroidal axis (B) Parabolic with convexity downward (C) Parabolic with convexity upward (D) Straight above centroidal axis

Last Answer : Answer: Option B

When a rectangular beam is loaded transversely, the maximum compressive stress develops on (A) Bottom fibre (B) Top fibre (C) Neutral axis (D) Every cross-section

Description : When a rectangular beam is loaded transversely, the maximum compressive stress develops on (A) Bottom fibre (B) Top fibre (C) Neutral axis (D) Every cross-section

Last Answer : (B) Top fibre

The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of 4 tonnes at the centre. The maximum stress in the bottom most fibre at the mid span section, is (A) 13.33 kg/cm2 tensile (B) 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive

Description : The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of ... 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive

Last Answer : (C) 26.67 kg/cm2 tensile

A 8 metre long simply supported rectangular beam which carries a distributed load 45 kg/m. experiences a maximum fibre stress 160 kg/cm2 . If the moment of inertia of the beam is 640 cm4 , the overall depth of the beam is (A) 10 cm (B) 12 cm (C) 15 cm (D) 18 cm

Description : A 8 metre long simply supported rectangular beam which carries a distributed load 45 kg/m. experiences a maximum fibre stress 160 kg/cm2 . If the moment of inertia of the beam is 640 cm4 , the overall depth of the beam is (A) 10 cm (B) 12 cm (C) 15 cm (D) 18 cm

Last Answer : (A) 10 cm

The maximum deflection of a simply supported beam of span L, carrying an isolated load at the centre of the span; flexural rigidity being EI, is (A) WL3 /3EL (B) WL3 /8EL (C) WL3 /24EL (D) WL3 /48EL

Description : The maximum deflection of a simply supported beam of span L, carrying an isolated load at the  centre of the span; flexural rigidity being EI, is  (A) WL3 /3EL (B) WL3 /8EL (C) WL3 /24EL (D) WL3 /48EL

Last Answer : (D) WL3 /48EL

A simply supported beam deflects by 5 mm when it is subjected to a concentrated load of 10 kN at its centre. What will be deflection in a 1/10 model of the beam if the model is subjected to a 1 kN load at its centre? (A) 5 mm (B) 0.5 mm (C) 0.05 mm (D) 0.005 mm

Description : A simply supported beam deflects by 5 mm when it is subjected to a concentrated load of 10 kN at its centre. What will be deflection in a 1/10 model of the beam if the model is subjected to a 1 kN load at its centre? (A) 5 mm (B) 0.5 mm (C) 0.05 mm (D) 0.005 mm

Last Answer : (A) 5 mm

The maximum deflection of a simply supported beam of length L with a central load W, is (A) WL²/48EI (B) W²L/24EI (C) WL3 /48EI (D) WL²/8EI

Description : The maximum deflection of a simply supported beam of length L with a central load W, is (A) WL²/48EI (B) W²L/24EI (C) WL3 /48EI (D) WL²/8EI

Last Answer : (C) WL3 /48EI

If the width of a simply supported beam carrying an isolated load at its centre is doubled, the deflection of the beam at the centre is changed by (A) 1/2 (B) 1/8 (C) 2 (D) 8

Description : If the width of a simply supported beam carrying an isolated load at its centre is doubled, the deflection of the beam at the centre is changed by (A) 1/2 (B) 1/8 (C) 2 (D) 8

Last Answer : (A) 1/2

If the width of a simply supported beam carrying an isolated load at its centre is doubled, the deflection of the beam at the centre is changed by (A) 2 times (B) 4 times (C) 8 times (D) 1/2 times

Description : If the width of a simply supported beam carrying an isolated load at its centre is doubled, the deflection of the beam at the centre is changed by (A) 2 times (B) 4 times (C) 8 times (D) 1/2 times

Last Answer : (C) 8 times

If the depth of a simply supported beam carrying an isolated load at its centre, is doubled, the deflection of the beam at the centre will be changed by a factor of (A) 2 (B) 1/2 (C) 8 (D) 1/8

Description : If the depth of a simply supported beam carrying an isolated load at its centre, is doubled, the deflection of the beam at the centre will be changed by a factor of (A) 2 (B) 1/2 (C) 8 (D) 1/8

Last Answer : (D) 1/8

If the width b and depth d of a beam simply supported with a central load are interchanged, the deflection at the centre of the beam will be changed in the ratio of (A) b/d (B) d/b (C) (d/b)2 (D) (b/d)

Description : If the width b and depth d of a beam simply supported with a central load are interchanged, the  deflection at the centre of the beam will be changed in the ratio of  (A) b/d (B) d/b (C) (d/b)2 (D) (b/d)

Last Answer : (D) (b/d)2

The maximum deflection of (A) A simply supported beam carrying a uniformly increasing load from either end and having the apex at the mid span is WL3 /60EI (B) A fixed ended beam carrying a distributed load over the span is WL3 /384EI (C) A fixed ended beam carrying a concentrated load at the mid span is WL3 /192EI (D) All the above

Description : The maximum deflection of  (A) A simply supported beam carrying a uniformly increasing load from either end and having  the apex at the mid span is WL3 /60EI (B) A fixed ended beam ... ended beam carrying a concentrated load at the mid span is WL3 /192EI (D) All the above 

Last Answer : (D) All the above 

Maximum deflection of a (A) Cantilever beam carrying a concentrated load W at its free end is WL3 /3EI (B) Simply supported beam carrying a concentrated load W at mid-span is WL3 /48EI (C) Cantilever beam, carrying a uniformly distributed load over span is WL3 /8EI (D) All the above

Description : Maximum deflection of a (A) Cantilever beam carrying a concentrated load W at its free end is WL3 /3EI (B) Simply supported beam carrying a concentrated load W at mid-span is WL3 /48EI (C) Cantilever beam, carrying a uniformly distributed load over span is WL3 /8EI (D) All the above

Last Answer : (D) All the above

The deflection of any rectangular beam simply supported, is (A) Directly proportional to its weight (B) Inversely proportional to its width (C) Inversely proportional to the cube of its depth (D) Directly proportional to the cube of its length

Description : The deflection of any rectangular beam simply supported, is (A) Directly proportional to its weight (B) Inversely proportional to its width (C) Inversely proportional to the cube of its depth (D) Directly proportional to the cube of its length

Last Answer : (C) Inversely proportional to the cube of its depth

For a simply supported beam of span 15 m, the minimum effective depth to satisfy the vertical deflection limits should be (A) 600 mm (B) 750 mm (C) 900 mm (D) More than 1 m

Description : For a simply supported beam of span 15 m, the minimum effective depth to satisfy the vertical deflection limits should be (A) 600 mm (B) 750 mm (C) 900 mm (D) More than 1 m

Last Answer : Answer: Option B

Basic value of span to depth ratio for simply supported beam to control deflection is [ A ] 7 [ B ] 20 [ C ] 26 [ D ] 35

Description : Basic value of span to depth ratio for simply supported beam to control deflection is [ A ] 7 [ B ] 20 [ C ] 26 [ D ] 35

Last Answer : [ B ] 20

A cantilever carries is uniformly distributed load W over its whole length and a force W acts at its free end upward. The net deflection of the free end will be (A) Zero (B) (5/24) (WL3 /EI) upward (C) (5/24) (WL3 /EI) downward (D) None of these

Description : A cantilever carries is uniformly distributed load W over its whole length and a force W acts at its  free end upward. The net deflection of the free end will be  (A) Zero  (B) (5/24) (WL3 /EI) upward  (C) (5/24) (WL3 /EI) downward  (D) None of these 

Last Answer : (B) (5/24) (WL3 /EI) upward

δ = (W a 2 b 2 ) / (3 EIL) is the value of deflection for ______ A. simply supported beam which has central point load B. simply supported beam which has eccentric point load C. simply supported beam which has U.D.L. point load per unit length D. fixed beam which has central point load

Description : δ = (W a 2 b 2 ) / (3 EIL) is the value of deflection for ______ A. simply supported beam which has central point load B. simply supported beam which has eccentric point load C. simply supported beam which has U.D.L. point load per unit length D. fixed beam which has central point load

Last Answer : B. simply supported beam which has eccentric point load

δ = (W a 2 b 2 ) / (3 EIl) is the value of deflection for ______ a. simply supported beam which has central point load b. simply supported beam which has eccentric point load c. simply supported beam which has U.D.L. point load per unit length d. fixed beam which has central point load

Description : δ = (W a 2 b 2 ) / (3 EIl) is the value of deflection for ______ a. simply supported beam which has central point load b. simply supported beam which has eccentric point load c. simply supported beam which has U.D.L. point load per unit length d. fixed beam which has central point load

Last Answer : b. simply supported beam which has eccentric point load

For the same span and loads fixed beam in comparison with simply supported beams has a. lesser value of maximum deflection b. more value of maximum deflecction c.twice the value of maximum deflecction d.same value of maximum deflecction

Description : For the same span and loads fixed beam in comparison with simply supported beams has a. lesser value of maximum deflection b. more value of maximum deflecction c.twice the value of maximum deflecction d.same value of maximum deflecction

Last Answer : a. lesser value of maximum deflection

A beam 3m long simply supported at its ends ,is carrying a point load W at the centre.If the slope at the ends of the beam should not exceed 10,find the deflection at the centre of beam? a.18.41 mm b.13.45 mm c.17.45 mm d.21.67 mm.

Description : A beam 3m long simply supported at its ends ,is carrying a point load W at the centre.If the slope at the ends of the beam should not exceed 10,find the deflection at the centre of beam? a.18.41 mm b.13.45 mm c.17.45 mm d.21.67 mm.

Last Answer : c.17.45 mm

A beam of uniform rectangular section 200 mm wide and 300mm deep is simply supported at its ends.It carries a uniformly distributed load of 9KN/m run over the entire span of 5m.If E=1×104 N/mm2, what is the maximum deflection? a.14.26 mm b.17.28 mm c.18.53 mm d.16.27 mm.

Description : A beam of uniform rectangular section 200 mm wide and 300mm deep is simply supported at its ends.It carries a uniformly distributed load of 9KN/m run over the entire span of 5m.If E=1×104 N/mm2, what is the maximum deflection? a.14.26 mm b.17.28 mm c.18.53 mm d.16.27 mm.

Last Answer : d.16.27 mm.

A simply supported beam carries a uniformly distributed load over the whole span.The deflection at the centre is y.If the distributed load per unit length is doubled and also depth of beam is doubled ,then the deflection at the centre would be a.2y b.4y c.y/2 d.y/4.

Description : A simply supported beam carries a uniformly distributed load over the whole span.The deflection at the centre is y.If the distributed load per unit length is doubled and also depth of beam is doubled ,then the deflection at the centre would be a.2y b.4y c.y/2 d.y/4.

Last Answer : d.y/4.

A simply supported beam is of rectangular section.It carries a uniformly distributed load over the whole span.The deflection at the centre is y.If the depth of beam is doubled ,the deflection at the centre would be a.2y b.4y c.y/2 d.y/8.

Description : A simply supported beam is of rectangular section.It carries a uniformly distributed load over the whole span.The deflection at the centre is y.If the depth of beam is doubled ,the deflection at the centre would be a.2y b.4y c.y/2 d.y/8.

Last Answer : d.y/8.

Which of the following statements is/are true for a simply supported beam? a. Deflection at supports in a simply supported beam is maximum. b.Deflection is maximum at a point where slope is zero . c. Slope is minimum at supports in a simply supported beam. d. All of the above.

Description : Which of the following statements is/are true for a simply supported beam? a. Deflection at supports in a simply supported beam is maximum. b.Deflection is maximum at a point where slope is zero . c. Slope is minimum at supports in a simply supported beam. d. All of the above

Last Answer : b.Deflection is maximum at a point where slope is zero .

Deflection of a simply supported beam when subjected to central point load is given as ________ a. (Wl /16 EI) b. (Wl2/16 EI) c. (Wl3/48 EI) d. (5Wl4/ 384EI)

Description : Deflection of a simply supported beam when subjected to central point load is given as ________ a. (Wl /16 EI) b. (Wl2/16 EI) c. (Wl3/48 EI) d. (5Wl4/ 384EI)

Last Answer : c. (Wl3/48 EI)

A simply supported beam carries uniformly distributed load of 20 kN/m over the length of 5 m. If flexural rigidity is 30000 kN.m2, what is the maximum deflection in the beam? a. 5.4 mm b. 1.08 mm c. 6.2 mm d. 8.6 mm

Description : A simply supported beam carries uniformly distributed load of 20 kN/m over the length of 5 m. If flexural rigidity is 30000 kN.m2, what is the maximum deflection in the beam? a. 5.4 mm b. 1.08 mm c. 6.2 mm d. 8.6 mm

Last Answer : a. 5.4 mm

In case of a beam subjected to pure bending a.107 dynes b.the stress intensity in any fibre is proportional to the distance of the fibre from the neutral axis c.the stress intensity in any fibre is proportional to the distance of the fibre from the load carrying end d.the stress intensity in any fibre is uniform e.the nature of stress in any fibre is identical

Description : In case of a beam subjected to pure bending a.107 dynes b.the stress intensity in any fibre is proportional to the distance of the fibre from the neutral axis c.the stress intensity in any fibre is ... d.the stress intensity in any fibre is uniform e.the nature of stress in any fibre is identical

Last Answer : b. the stress intensity in any fibre is proportional to the distance of the fibre from the neutral axis

The demand curve for a Giffen good is (1) upward rising (2) downward falling (3) parallel to the quantity axis (4) parallel to the price axis

Description : The demand curve for a Giffen good is (1) upward rising (2) downward falling (3) parallel to the quantity axis (4) parallel to the price axis

Last Answer : (1) upward rising Explanation: A Giffen good is a good whose consumption in-creases as its price increases. (For a normal good, as the price increases, consumption decreases.) Thus, the ... a price changes the income effect outweighs the substitution effect and this leads to perverse demand curve.

Long run supply curve of a decreasing cost industry is (a) Downward sloping curve ; (b) Upward sloping curve; (c) Straight line parallel to X axis ; (d) Straight line parallel to y axis

Description : Long run supply curve of a decreasing cost industry is (a) Downward sloping curve ; (b) Upward sloping curve; (c) Straight line parallel to X axis ; (d) Straight line parallel to y axis

Last Answer : (a) Downward sloping curve ;

Long run supply curve of a increasing cost industry is (a) Horizontal line overlapping X axis ; (b) Upward sloping line; (c) Downward sloping line ; (d) Vertical line

Description : Long run supply curve of a increasing cost industry is (a) Horizontal line overlapping X axis ; (b) Upward sloping line; (c) Downward sloping line ; (d) Vertical line 

Last Answer : (b) Upward sloping line; 

The demand curve for a Giffen good is (1) upward rising (2) downward falling (3) parallel to the quantity axis (4) parallel to the price axis

Description : The demand curve for a Giffen good is (1) upward rising (2) downward falling (3) parallel to the quantity axis (4) parallel to the price axis 

Last Answer : upward rising

A rolled steel joist is simply supported at its ends and carries a uniformly distributed load which causes a maximum deflection of 10 mm and slope at the ends of 0.002 radian. The length of the joist will be, (A) 10 m (B) 12 m (C) 14 m (D) 16 m

Description : A rolled steel joist is simply supported at its ends and carries a uniformly distributed load which  causes a maximum deflection of 10 mm and slope at the ends of 0.002 radian. The length of the  joist will be,  (A) 10 m  (B) 12 m  (C) 14 m  (D) 16 m 

Last Answer : (D) 16 m 

A simply supported uniform rectangular bar breadth b, depth d and length L carries an isolated load W at its mid-span. The same bar experiences an extension e under same tensile load. The ratio of the maximum deflection to the elongation, is (A) L/d (B) L/2d (C) (L/2d)² (D) (L/3d)²

Description : A simply supported uniform rectangular bar breadth b, depth d and length L carries an isolated  load W at its mid-span. The same bar experiences an extension e under same tensile load. The  ratio of the maximum deflection to the ... (A) L/d (B) L/2d (C) (L/2d)² (D) (L/3d)²

Last Answer : (C) (L/2d)

A uniform girder simply supported at its ends is subjected to a uniformly distributed load over its entire length and is propped at the centre so as to neutralise the deflection. The net B.M. at the centre will be (A) WL (B) WL/8 (C) WL/24 (D) WL/32

Description : A uniform girder simply supported at its ends is subjected to a uniformly distributed load over its entire length and is propped at the centre so as to neutralise the deflection. The net B.M. at the centre will be (A) WL (B) WL/8 (C) WL/24 (D) WL/32

Last Answer : (D) WL/32

The maximum compressive stress at the top of a beam is 1600 kg/cm2 and the corresponding tensile stress at its bottom is 400 kg/cm2 . If the depth of the beam is 10 cm, the neutral axis from the top, is(A) 2 cm (B) 4 cm (C) 6 cm (D) 8 cm

Description : The maximum compressive stress at the top of a beam is 1600 kg/cm2 and the corresponding tensile stress at its bottom is 400 kg/cm2 . If the depth of the beam is 10 cm, the neutral axis from the top, is (A) 2 cm (B) 4 cm (C) 6 cm (D) 8 cm

Last Answer : (D) 8 cm

The neutral axis of a beam cross-section must (A) Pass through the centroid of the section (B) Be equidistant from the top of bottom films (C) Be an axis of symmetry of the section (D) None of these

Description : The neutral axis of a beam cross-section must (A) Pass through the centroid of the section (B) Be equidistant from the top of bottom films (C) Be an axis of symmetry of the section (D) None of these

Last Answer : (A) Pass through the centroid of the section

The section of the beam having greater width at the top in comparison to the width below neutral axis is known as. (a) Critical section (b) T-section (c) L-section (d) None of these

Description : The section of the beam having greater width at the top in comparison to the width below neutral axis is known as. (a) Critical section (b) T-section (c) L-section (d) None of these

Last Answer : (b) T-section

The effective depth of a singly reinforced rectangular beam is 300mm. the section is over-reinforced and the neutral axis is 120mm below the top. If the maximum stress attained by concrete is 5N/mn2 and the modular ratio is 18, then the stress developed in the steel will (a) 130N/mm2 (b) 135N/mm2 (c) 160N/mm2 (d) 180N/mm2

Description : The effective depth of a singly reinforced rectangular beam is 300mm. the section is over-reinforced and the neutral axis is 120mm below the top. If the maximum stress attained by concrete is 5N/mn2 and the modular ratio ... in the steel will (a) 130N/mm2 (b) 135N/mm2 (c) 160N/mm2 (d) 180N/mm2

Last Answer : (b) 135N/mm2

In a simply supported beam loaded with U.D.L over the whole section, the bending stress is …………. at top and ………….. at bottom. (a) Compressive, tensile (b) Tensile, compressive (c) Tensile, zero (d) Compressive, zero

Description : In a simply supported beam loaded with U.D.L over the whole section, the bending stress is …………. at top and ………….. at bottom. (a) Compressive, tensile (b) Tensile, compressive (c) Tensile, zero (d) Compressive, zero

Last Answer : (a) Compressive, tensile

If the load on beam is increased, the tensile stress sin the concrete below the neutral axis will (a) Increase (b) Decrease (c) Remain unchanged (d) None of these

Description : If the load on beam is increased, the tensile stress sin the concrete below the neutral axis will (a) Increase (b) Decrease (c) Remain unchanged (d) None of these

Last Answer : (a) Increase

The ratio of the length and diameter of a simply supported uniform circular beam which experiences maximum bending stress equal to tensile stress due to same load at its mid span, is (A) 1/8 (B) 1/4 (C) 1/2 (D) 1/3

Description : The ratio of the length and diameter of a simply supported uniform circular beam which  experiences maximum bending stress equal to tensile stress due to same load at its mid span, is  (A) 1/8  (B) 1/4  (C) 1/2  (D) 1/3 

Last Answer : (C) 1/2 

In case of a simply supported rectangular beam of span L and loaded with a central load W, the length of elasto-plastic zone of the plastic hinge, is (A) L/2 (B) L/3 (C) L/4 (D) L/5

Description : In case of a simply supported rectangular beam of span L and loaded with a central load W, the  length of elasto-plastic zone of the plastic hinge, is  (A) L/2  (B) L/3  (C) L/4  (D) L/5 

Last Answer : (B) L/3 

The ratio of the maximum deflections of a simply supported beam with a central load W and of a cantilever of same length and with a load W at its free end, is (A) 1/8 (B) 1/10 (C) 1/12 (D) 1/16

Description : The ratio of the maximum deflections of a simply supported beam with a central load W and of a  cantilever of same length and with a load W at its free end, is  (A) 1/8  (B) 1/10  (C) 1/12  (D) 1/16 

Last Answer : (D) 1/16