The ratio of maximum shear stress to average shear stress of a circular beam, is
(A) 2/3
(B) 3/2
(C) 3/4
(D) 4/3
Description : The average shear stress in a beam of circular section is _______ times the maximum shear stress. a. 0.75 b. 1.5 c. 4/3 d. equa
Last Answer : a. 0.75
Description : The ratio of maximum shear stress to average shear stress is 4/3 in _______ a. circular cross-section b. rectangular cross-section c. square cross-section d. all of the above
Last Answer : a. circular cross-section
Description : The maximum shear stress (qmax) in a rectangular beam is (A) 1.25 times the average (B) 1.50 times the average (C) 1.75 times the average (D) 2.0 times the average
Last Answer : Answer: Option B
Description : The maximum shear stress in rectangular beam is _____________________times of average shear stress. (a) 1.15 (b) 1.25 (c) 1.50 (d) 1.75
Last Answer : (c) 1.50
Description : A hollow prismatic beam of circular section is subjected to a torsional moment. The maximum shear stress occurs at (a) inner wall of cross section (b) middle of thickness (c) outer surface of shaft (d) none of these
Last Answer : (c) outer surface of shaft
Description : In a reinforced concrete beam , the shear stress distribution above the neutral axis following a (a) A straight line (b) Circular curve (c) Parabolic curve (d) All the above
Last Answer : (c) Parabolic curve
Description : The ratio of the length and diameter of a simply supported uniform circular beam which experiences maximum bending stress equal to tensile stress due to same load at its mid span, is (A) 1/8 (B) 1/4 (C) 1/2 (D) 1/3
Last Answer : (C) 1/2
Description : What is the average shear stress acting on a rectangular beam, if 50 N/mm2is the maximum shear stress acting on it? a. 31.5 N/mm2 b. 33.33 N/mm2 c. 37.5 N/mm2 d. 42.5 N/mm2
Last Answer : b. 33.33 N/mm2
Description : Consider the following statements in respect of steady laminar flow through a circular pipe: 1. Shear stress is zero on the central axis of the pipe 2. Discharge varies directly with the viscosity of the fluid 3. Velocity is maximum at the ... 2 , 3 & 4 (b) 1 & 3 only (c) 2 & 4 only (d)3 & 4 only
Last Answer : (b) 1 & 3 only
Description : If the maximum shear stress at the end of a simply supported R.C.C. beam of 6 m effective span is 10 kg/cm2 , the share stirrups are provided for a distance from either end where, is (A) 50 cm (B) 100 cm (C) 150 cm (D) 200 cm
Last Answer : Answer: Option C
Description : The maximum shear stress (q) in concrete of a reinforced cement concrete beam is (A) Shear force/(Lever arm × Width) (B) Lever arm/(Shear force × Width) (C) Width/(Lever arm × Shear force) (D) (Shear force × Width)/Lever arm
Last Answer : Answer: Option A
Description : An R.C.C. beam of 25 cm width and 50 cm effective depth has a clear span of 6 metres and carries a U.D.L. of 3000 kg/m inclusive of its self weight. If the lever arm constant for the section is 0.865, the maximum intensity ... , is (A) 8.3 kg/cm2 (B) 7.6 kg/cm2 (C) 21.5 kg/cm2 (D) 11.4 kg/cm2
Description : If the maximum shear stress at the end of a simply supported R.C.C. beam of 16 m effective span is 10 kg/cm2 , the length of the beam having nominal reinforcement, is (A) 8 cm (B) 6 m (C) 8 m (D) 10 m
Description : For a reinforced concrete beam section, the shape of shear stress diagram is (a) Parabolic over the whole section with maximum value at the neutral axis. (b) Parabolic above the neutral axis and rectangular below the neutral axis. (c) Linearly varying as the distance form the N.A. (d) All the above.
Last Answer : (b) Parabolic above the neutral axis and rectangular below the neutral axis.
Description : If the shear force along a section of a beam is zero, the bending moment at the section is (A) Zero (B) Maximum (C) Minimum (D) Average of maximum-minimum
Last Answer : (B) Maximum
Description : Distribution of shear intensity over a rectangular section of a beam, follows: (A) A circular curve (B) A straight line (C) A parabolic curve (D) An elliptical curve
Description : In case of laminar flow of fluid through a circular pipe, the (A) Shear stress over the cross-section is proportional to the distance from the surface of the pipe (B) Surface of velocity distribution is a ... occurs at a radial distance of 0.5 r from the centre of the pipe (r = pipe radius)
Last Answer : (B) Surface of velocity distribution is a paraboloid of revolution, whose volume equals half the volume of circumscribing cylinder
Description : The bending moment ‘M’ and a torque ‘T’ is applied on a solid circular shaft. If the maximum bending stress equals to maximum shear stress developed, then ‘M’ is equal to (A) T/2 (B) T (C) 2 T (D) 4 T
Last Answer : (A) T/2
Description : A hollow circular tube with a 2.3-cm I.D. and 2.5-cm O.D. is rigidly supported at its ends. A 2.5 kN-m torque is applied at the center of this tube. What is the maximum shear stress acting on this tube? (a) 2.87Mpa (b) 4.27 Mpa (c) 6.92 Mpa (d) 10.2 Mpa
Last Answer : (a) 2.87Mpa
Description : A circular shaft subjected to torsion undergoes a twist of 10in a length of 120 cm. If the maximum shear stress induced is limited to 1000 kg/cm2and if modulus of rigidity G = 0.8 x 106then the radius of the shaft should be (a) p/8 (b) p/27 (c) 18/p (d) 27/p
Last Answer : (d) 27/p
Description : A circular pipe is subjected to maximum shear force of 60 kN. What is the diameter of the pipe if maximum allowable shear stress is 5 Mpa? a. 27.311 mm b. 75.56 mm c. 142.72 mm d. 692.10 mm
Last Answer : c. 142.72 mm
Description : Shear stress in a I-section beam is maximum art the (a) Outermost fiber (b) At the junction of web and flange (c) Central fiber (d) None
Last Answer : b) At the junction of web and flange
Description : The shear stress acting on the neutral axis of a beam is _____ a. maximum b. minimum c. zero d. none of the above
Last Answer : a. maximum
Description : State the position of maximum shear stress and bending stress in S/S rectangular beam section carrying udl.
Last Answer : i. Maximum shear stress developed at the neutral axis of the rectangular section at support of simply supported beam. ii. Maximum bending stress developed at the top and bottom fibre of the rectangular section at mid span of simply supported beam.
Description : A diagram which shows the variations of the axial load for all sections of the span of a beam, is called (A) Bending moment diagram (B) Shear force diagram (C) Thrust diagram (D) Stress diagram
Description : A beam is said to be of uniform strength, if (A) B.M. is same throughout the beam (B) Shear stress is same throughout the beam (C) Deflection is same throughout the beam (D) Bending stress is same at every section along its longitudinal axis
Last Answer : (D) Bending stress is same at every section along its longitudinal axis
Description : A beam is said to be of uniform strength, if (A) B.M. is same throughout the beam (B) Deflection is same throughout the beam (C) Bending stress is same throughout the beam (D) Shear stress is same throughout the beam
Last Answer : (C) Bending stress is same throughout the beam
Description : The reinforced concrete beam which has width 25 cm, lever arm 40 cm, shear force 6t/cm2 , safe shear stress 5 kg/cm2 and B.M. 24 mt, (A) Is safe in shear (B) Is unsafe in shear (C) Is over safe in shear (D) Needs redesigning
Description : Steel beam theory is used for (A) Design of simple steel beams (B) Steel beams encased in concrete (C) Doubly reinforced beams ignoring compressive stress in concrete (D) Beams if shear exceeds 4 times allowable shear stress
Description : Pick up the incorrect statement from the following. The intensity of horizontal shear stress at the elemental part of a beam section, is directly proportional to (A) Shear force (B) Area of the section ... . of the area from its neutral axis (D) Moment of the beam section about its neutral axis
Last Answer : Answer: Option D
Description : In a beam the local bond stress Sb, is equal to (A) Shear force/(Leaver arm Total perimeter of reinforcement) (B) Total perimeter of reinforcement/(Leaver arm Shear force) (C) ... force Total perimeter of reinforcement) (D) Leaver arm/(Bending moment Total perimeter of reinforcement)
Description : Dimensions of a beam need be changed if the shear stress is more than (A) 10 kg/cm2 (B) 15 kg/cm2 (C) 20 kg/cm2 (D) 25 kg/cm
Description : If the shear stress in a R.C.C. beam is (A) Equal or less than 5 kg/cm2 , no shear reinforcement is provided (B) Greater than 4 kg/cm2 , but less than 20 kg/cm2 , shear reinforcement is provided (C) Greater than 20 kg/cm2 , the size of the section is changed (D) All the above
Description : In the zone of R.C.C. beam where shear stress is less than 5 kg/cm2 , nominal reinforcement is provided at a pitch of (A) One-half lever arm of the section (B) One-third lever arm of the section (C) Lever arm of the section (D) One and half lever arm of the section
Description : Pick up the incorrect statement from the following: Tensile reinforcement bars of a rectangular beam (A) Are curtailed if not required to resist the bending moment (B) Are bent up at suitable ... to serve as shear reinforcement (D) Are maintained at bottom to provide at least local bond stress
Description : An R.C.C. beam of 6 m span is 30 cm wide and has a lever arm of 55 cm. If it carries a U.D.L. of 12 t per m and allowable shear stress is 5 kg/cm2 , the beam (A) Is safe in shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined bars (D) Needs revision of section
Description : The main reason for providing number of reinforcing bars at a support in a simply supported beam is to resist in that zone (A) Compressive stress (B) Shear stress (C) Bond stress (D) Tensile stress
Description : A shaft is subjected to bending moment M and a torque T simultaneously. The ratio of the maximum bending stress to maximum shear stress developed in the shaft, is (A) M/T (B) T/M (C) 2M/T (D) 2T/M
Last Answer : (C) 2M/T
Description : If the strain energy stored per unit volume in a hollow shaft subjected to a pure torque when t attains maximum shear stress fs the ratio of inner diameter to outer diameter, is 17/64 (fs/N) (A) 1/2 (B) 1/3 (C) 1/4 (D) 1/5
Last Answer : (C) 1/4
Description : In alluvial channels carrying clear water, the ratio of maximum tractive shear stress on the slides and that on the channel beams approximately. a) 0.5 b) 1.76 c) 0.76 d) 1.5
Last Answer : c) 0.76
Description : The ratio of the length and depth of a simply supported rectangular beam which experiences maximum bending stress equal to tensile stress, due to same load at its mid span, is (A) 1/2 (B) 2/3 (C) 1/4 (D) 1/3
Last Answer : (B) 2/3
Description : The effective depth of a singly reinforced rectangular beam is 300mm. the section is over-reinforced and the neutral axis is 120mm below the top. If the maximum stress attained by concrete is 5N/mn2 and the modular ratio ... in the steel will (a) 130N/mm2 (b) 135N/mm2 (c) 160N/mm2 (d) 180N/mm2
Last Answer : (b) 135N/mm2
Description : The ratio of maximum and average shear stresses on a rectangular section, is (A) 1 (B) 1.25 (C) 1.5 (D) 2.5
Last Answer : (C) 1.5
Description : If L is the effective span of a R.C.C. beam which is subjected to maximum shear qmax at the ends, the distance from either end over which stirrups for the shear, are provided, is (A) (L/2) (1 - 3/qmax) (B) (L/3) (1 - 5/qmax) (C) (L/2) (1 - 5/qmax) (D) (L/2) (1 - 2/qmax)
Description : In a ring beam subjected to uniformly distributed load (i) Shear force at mid span is zero (ii) Shear force at mid span is maximum (iii) Torsion at mid span is zero (iv) Torsion at mid span is maximum The correct answer ... and (iii) (B) (i) and (iv) (C) (ii) and (iii) (D) (ii) and (iv)
Last Answer : Option A
Description : For a strongest rectangular beam cut from a circular log, the ratio of the width and depth, is (A) 0.303 (B) 0.404 (C) 0.505 (D) 0.707
Last Answer : (D) 0.707
Description : Drag co-efficient for flow past immersed body is the ratio of __________ to the product of velocity head and density. (A) Shear stress (B) Shear force (C) Average drag per unit projected area (D) None of these
Last Answer : (C) Average drag per unit projected area
Description : Maximum shear stress is (a) Average sum of principal stresses (b) Average difference of principal stresses (c) Average sum as well as difference of principal stresses (d) None
Last Answer : (b) Average difference of principal stresses
Description : If the critical shear stress of a channel is XC, then the average value of shear stress required to move the grain on the bank is (A) 0.5 XC (B) 0.75 TC (C) XC (D) 1.33 TC
Description : If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed
Last Answer : a) M/2πtr2