Description : A pre-stressed concrete member is preferred because (A) Its dimensions are not decided from the diagonal tensile stress (B) Large size of long beams carrying large shear force need not be adopted (C) Removal of cracks in the members due to shrinkage (D) All the above
Last Answer : Answer: Option D
Description : The allowable shear stress in the web of mild steel beams decreases with (a) Decrease in h/t ratio (b) Increase in h/t ratio (c ) Decrease in thickness (d) Increase in height Where h is the height and t is the thickness
Last Answer : (b) Increase in h/t ratio
Description : The Maximum shear stress in Slabs should not exceed -------- the maximum values allowed for beams. [ A ] Half Of [ B ] One-Fourth Of [ C ] Twice [ D ] Those Given In
Last Answer : [ A ] Half Of
Description : An R.C.C. beam of 25 cm width and 50 cm effective depth has a clear span of 6 metres and carries a U.D.L. of 3000 kg/m inclusive of its self weight. If the lever arm constant for the section is 0.865, the maximum intensity ... , is (A) 8.3 kg/cm2 (B) 7.6 kg/cm2 (C) 21.5 kg/cm2 (D) 11.4 kg/cm2
Last Answer : Answer: Option A
Description : Steel beam theory is used for (A) Design of simple steel beams (B) Steel beams encased in concrete (C) Doubly reinforced beams ignoring compressive stress in concrete (D) Beams if shear exceeds 4 times allowable shear stress
Last Answer : Answer: Option C
Description : The allowable shear stress in stiffened webs of mild steel beams decreases with (a) Decrease in the spacing of the stiffeners (b) Increase in the spacing of the stiffeners (c) Decrease in the effective depth (d) Increase in the effective depth
Last Answer : (b) Increase in the spacing of the stiffeners
Description : The ratio of the thickness of web to that of flange of steel rolled structural beams and channels is (A) Less than 1 (B) Equal to 1 (C) Greater than 1 (D) Less than 1 in beams but greater than 1 in channels
Description : The cross sections of the beams of equal length are a circle and a square whose permissible bending stress is same under same maximum bending. The ratio of their flexural weights is, (A) 1.118 (B) 1.338 (C) 1.228 (D) 1.108
Last Answer : (A) 1.118
Description : If the critical shear stress of a channel is XC, then the average value of shear stress required to move the grain on the bank is (A) 0.5 XC (B) 0.75 TC (C) XC (D) 1.33 TC
Last Answer : Answer: Option B
Description : State the position of maximum shear stress and bending stress in S/S rectangular beam section carrying udl.
Last Answer : i. Maximum shear stress developed at the neutral axis of the rectangular section at support of simply supported beam. ii. Maximum bending stress developed at the top and bottom fibre of the rectangular section at mid span of simply supported beam.
Description : If yielding strength=400N/mm2, the find the permissible shear stress according to ASME standards. a) 72 N/mm2 b) 76 N/mm2 c) 268 N/mm2 d) 422 N/mm2
Last Answer : a) 72 N/mm2
Description : If yielding strength=400N/mm², the find the permissible shear stress according to ASME standards. a) 72 N/mm² b) 76 N/mm² c) 268 N/mm² d) 422 N/mm²
Last Answer : a) 72 N/mm²
Description : If the strain energy stored per unit volume in a hollow shaft subjected to a pure torque when t attains maximum shear stress fs the ratio of inner diameter to outer diameter, is 17/64 (fs/N) (A) 1/2 (B) 1/3 (C) 1/4 (D) 1/5
Last Answer : (C) 1/4
Description : A shaft is subjected to bending moment M and a torque T simultaneously. The ratio of the maximum bending stress to maximum shear stress developed in the shaft, is (A) M/T (B) T/M (C) 2M/T (D) 2T/M
Last Answer : (C) 2M/T
Description : The ratio of maximum shear stress to average shear stress of a circular beam, is (A) 2/3 (B) 3/2 (C) 3/4 (D) 4/3
Last Answer : (D) 4/3
Description : An intermediate T-beam reinforced with two layers of tensile steel with clear cover 13 cm encasted with the floor of a hall 12 metres by 7 metres, is spaced at 3 metres from adjoining beams and if the width of the beam is ... breadth of the flange is (A) 300 cm (B) 233 cm (C) 176 cm (D) 236 cm
Description : Design of R.C.C. simply supported beams carrying U.D.L. is based on the resultant B.M. at (A) Supports (B) Mid span (C) Every section (D) Quarter span
Description : The deep beams are designed for (a) Shear force only (b) Bending moment only (c) Both S.F & B.M (d) Bearing
Last Answer : (b) Bending moment only
Description : A simply supported beam A carries a point load at its mid span. Another identical beam B carries the same load but uniformly distributed over the entire span. The ratio of the maximum deflections of the beams A and B, will be (A) 2/3 (B) 3/2 (C) 5/8 (D) 8/5
Last Answer : (D) 8/5
Description : In a combined footing for two columns carrying unequal loads, the maximum hogging bending moment occurs at (A) Less loaded column (B) More loaded column (C) A point of the maximum shear force (D) A point of zero shear force
Description : The ratio of average values of shear stresses produced on the bed and the banks of a channel due to flowing water is (A) Less than 1 (B) Equal to 1 (C) Greater than 1 (D) Equal to zero
Description : 0 Pick up the correct statement from the following: (A) The point through which the resultant of the shear stresses passes is known as shear centre (B) In the standard rolled channels, the shear centre ... horizontal plane and away from the C.G., outside of the leg projection (D) All the above
Last Answer : (D) All the above
Description : A block of weight 20 kg slides with an initial velocity of 2 m sec down an inclined plane on to a spring of stiffness 10 kg/cm. If the co--efficient of friction is 0.2, angle ? = 30 the ratio of ... be a.More than one b.One c.Less than one d.Depends on the stiffness of spring e.None of the above
Last Answer : a. More than one
Description : If a solid shaft (diameter 20 cm, length 400 cm, N = 0.8 × 105 N/mm2 ) when subjected to a twisting moment, produces maximum shear stress of 50 N/mm2 , the angle of twist in radians, is (A) 0.001 (B) 0.002 (C) 0.0025 (D) 0.003
Last Answer : (C) 0.0025
Description : The maximum load to which a fillet joint of length can be subjected to, is (A) 0.7 × S × fillet size × L (B) 2 × S × fillet size × L (C) Permissible shear stress × fillet size × L (D) (S × fillet size × L)/3
Last Answer : (A) 0.7 × S × fillet size × L
Description : The maximum shear stress (qmax) in a rectangular beam is (A) 1.25 times the average (B) 1.50 times the average (C) 1.75 times the average (D) 2.0 times the average
Description : As per IS:456, maximum shear stress for M20 glade concrete in working stress method is [ A ] 1.6 N/mm2 [ B ] 1.8 N/mm2 [ C ] 2.0 N/mm2 [ D ] 2.2 N/mm2
Last Answer : [ B ] 1.8 N/mm2
Description : Consider the following statements. In case of flood routing in a river channel by Muskingum method, the coefficient x represents : 1. A dimensionless constant indicating the relative importance of inflow and outflow in determining storage ... , 3 and 4 only (c) 1, 2 and 3 only (d) 2, 3 and 4 only
Last Answer : (b) 1, 3 and 4 only
Description : According to the steel beam theory of doubly reinforced beams (A) Tension is resisted by tension steel (B) Compression is resisted by compression steel (C) Stress in tension steel equals the stress in compression steel (D) All the above
Description : Pre-stress loss due to friction occurs (A) Only in post-tensioned beams (B) Only in pre-tensioned beams (C) In both post-tensioned and pre-tensioned beams (D) None of the above
Description : The maximum area of tension reinforcement in beams shall not exceed (A) 0.15 % (B) 1.5 % (C) 4 % (D) 1 %
Description : For a continuous floor slab supported on beams, the ratio of end span length and intermediate span length, is (A) 0.6 (B) 0.7 (C) 0.8 (D) 0.9
Description : The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate spans is kept (A) 0.7 (B) 0.8 (C) 0.9 (D) 0.6
Description : The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate span is kept. (a) 0.7 (b) 0.8 (c) 0.9 (d) 0.6
Last Answer : (c) 0.9
Description : The ratio of maximum bending stress to maximum shear stress on the cross section when a shaft is simultaneously subjected to a torque T and bending moment M, a. T/M b. M/T c. 2T/M d. 2M/T
Last Answer : d. 2M/T
Description : The ratio of maximum shear stress to average shear stress is 4/3 in _______ a. circular cross-section b. rectangular cross-section c. square cross-section d. all of the above
Last Answer : a. circular cross-section
Description : Maximum allowable shear stress for M25 grade concrete is [ A ] 2.5 N/mm2 [ B ] 2.8 N/mm2 [ C ] 3.1 N/mm2 [ D ] 3.5 N/mm2
Last Answer : [ C ] 3.1 N/mm2
Description : The ratio of shear stress and shear strain of an elastic material, is (A) Modulus of Rigidity (B) Shear Modulus (C) Modulus of Elasticity (D) Both (a) and (b)
Last Answer : (D) Both (a) and (b)
Description : Factor of safety against sliding of a slope, is the ratio of (A) Actual cohesion to that required to maintain stability of slope (B) Shear strength to shear stress along the surface (C) Neither (a) nor (b) (D) Both (a) and (b)
Description : Viscous force is the __________ of shear stress due to viscosity and cross-section area of flow. (A) Sum (B) Different (C) Product (D) Ratio
Description : Bulk modulus of a fluid is the ratio of (A) Shear stress to shear strain (B) Increase in volume to the viscosity of fluid (C) Increase in pressure to the volumetric strain (D) Critical velocity to the viscosity of fluid
Description : Critical shear stress of cohesive sediment (a) Decreases with the void ratio for a given plasticity index (b) Increases with the plasticity index for a given void ratio (c) Increases with shear strength for a given clay content (d) All of the above.
Last Answer : (c) Increases with shear strength for a given clay content
Description : The Maximum percentage of steel in tension allowed for beams [ A ] 0.2 [ B ] 0.4 [ C ] 2 [ D ] 4
Last Answer : [ A ] 0.2
Description : Pick up the correct statement from the following: (A) For channels, the shear centre does not coincide its centroid (B) The point of intersection of the bending axis with the cross section ... shear centre coincides with the centroid of the cross section of the beam (D) All the above
Last Answer : For given maximum axle load tractive efforts of AC. locomotive will be more than that of D.C. locomotive.
Description : Two parallel wires carrying current in the same direction attract each other while two beams of electrons travelling in the same direction repel each
Last Answer : Two parallel wires carrying current in the same direction attract each other while two beams of ... force between them D. magnetic force between them
Description : Macaulays method is more convenient for beams carrying a. Single concentrated load. b.UDL c. Multi loads d.None.
Last Answer : c. Multi loads
Description : The maximum magnitude of shear stress due to shear force F on a rectangular section of area A at the neutral axis, is (A) F/A (B) F/2A (C) 3F/2A (D) 2F/3A
Last Answer : (C) 3F/2A
Description : Pick up the correct statement from the following: (A) The bending stress in a section is zero at its neutral axis and maximum at the outer fibres (B) The shear stress is zero at the outer ... (C) The bending stress at the outer fibres, is known as principal stress (D) All the above
Description : Pick up the correct statement from the following: (A) Mcg = M M 2 + r2 ) where letters carry their usual meanings (B) Tcp = m 2 + T2 )where ... maximum shear stress caused by the combined bending and torsion, is called equivalent torque (D) All the above