A beam is said to be of uniform strength, if (A) B.M. is same throughout the beam (B) Shear stress is same throughout the beam (C) Deflection is same throughout the beam (D) Bending stress is same at every section along its longitudinal axis

A beam is said to be of uniform strength, if
(A) B.M. is same throughout the beam
(B) Shear stress is same throughout the beam
(C) Deflection is same throughout the beam
(D) Bending stress is same at every section along its longitudinal axis
by

1 Answer

Answer :

(D) Bending stress is same at every section along its longitudinal axis
by

Related questions

A beam is said to be of uniform strength, if (A) B.M. is same throughout the beam (B) Deflection is same throughout the beam (C) Bending stress is same throughout the beam (D) Shear stress is same throughout the beam

Description : A beam is said to be of uniform strength, if (A) B.M. is same throughout the beam (B) Deflection is same throughout the beam (C) Bending stress is same throughout the beam (D) Shear stress is same throughout the beam

Last Answer : (C) Bending stress is same throughout the beam

A beam of uniform strength has a. same cross-section throughout the beam b. same bending stress at every section c. same bending moment at every section d. same shear stress at every section

Description : A beam of uniform strength has a. same cross-section throughout the beam b. same bending stress at every section c. same bending moment at every section d. same shear stress at every section

Last Answer : b. same bending stress at every section

In a simple bending theory, one of the assumption is that the plane sections before bending remain plane after bending. This assumption means that a. stress is uniform throughout the beam b. strain is uniform throughout the beam c. stress is proportional to the distance from the neutral axis d. strain is proportional to the distance from the neutral axis

Description : In a simple bending theory, one of the assumption is that the plane sections before bending remain plane after bending. This assumption means that a. stress is uniform throughout the beam b. ... the distance from the neutral axis d. strain is proportional to the distance from the neutral axis

Last Answer : d. strain is proportional to the distance from the neutral axis

In a R.C section under flexure, the assumption that “a plane section before bending remains plane after bending” leads to (a) Strain distribution being linear across the depth (b) Stress distribution being linear across the depth (c) Both stress and strain distribution being linear across the depth (d) Shear stress distribution being uniform along the depth

Description : In a R.C section under flexure, the assumption that a plane section before bending remains plane after bending leads to (a) Strain distribution being linear across the depth (b) ... strain distribution being linear across the depth (d) Shear stress distribution being uniform along the depth

Last Answer : (a) Strain distribution being linear across the depth

If a constant section beam is subjected to a uniform bending moment throughout, its length bends to (A) A circular arc (B) A parabolic arc (C) A catenary (D) None of these

Description : If a constant section beam is subjected to a uniform bending moment throughout, its length bends  to  (A) A circular arc  (B) A parabolic arc  (C) A catenary  (D) None of these 

Last Answer : (A) A circular arc 

The graphical representation of variation of axial load on y axis and position of cross section along x axis is called as _____ (a) Bending moment diagram (b) Shear force diagram (c) Stress-strain diagram (d) Trust diagram

Description : The graphical representation of variation of axial load on y axis and position of cross section along x axis is called as _____ (a) Bending moment diagram (b) Shear force diagram (c) Stress-strain diagram (d) Trust diagram

Last Answer : (d) Trust diagram

Pick up the correct statement from the following: (A) For channels, the shear centre does not coincide its centroid (B) The point of intersection of the bending axis with the cross section of the beam, is called shear centre (C) For I sections, the shear centre coincides with the centroid of the cross section of the beam (D) All the above

Description : Pick up the correct statement from the following:  (A) For channels, the shear centre does not coincide its centroid  (B) The point of intersection of the bending axis with the cross section ... shear centre coincides with the centroid of the cross section of the beam  (D) All the above

Last Answer : (D) All the above

What is the shear stress acting along the neutral axis of triangular beam section, with base 60 mm and height 150 mm, when shear force of 30 kN acts? a. 15.36 N/mm2 b. 10.6 N/mm2 c. 8.88 N/mm2 d. Insufficient data

Description : What is the shear stress acting along the neutral axis of triangular beam section, with base 60 mm and height 150 mm, when shear force of 30 kN acts? a. 15.36 N/mm2 b. 10.6 N/mm2 c. 8.88 N/mm2 d. Insufficient data

Last Answer : c. 8.88 N/mm2

If the shear force along a section of a beam is zero, the bending moment at the section is (A) Zero (B) Maximum (C) Minimum (D) Average of maximum-minimum

Description : If the shear force along a section of a beam is zero, the bending moment at the section is  (A) Zero  (B) Maximum  (C) Minimum  (D) Average of maximum-minimum 

Last Answer : (B) Maximum 

Pick up the correct statement from the following: (A) The bending stress in a section is zero at its neutral axis and maximum at the outer fibres (B) The shear stress is zero at the outer fibres and maximum at the neutral axis (C) The bending stress at the outer fibres, is known as principal stress (D) All the above

Description : Pick up the correct statement from the following:  (A) The bending stress in a section is zero at its neutral axis and maximum at the outer fibres  (B) The shear stress is zero at the outer ... (C) The bending stress at the outer fibres, is known as principal stress  (D) All the above 

Last Answer : (D) All the above 

Pick up the incorrect statement from the following. The intensity of horizontal shear stress at the elemental part of a beam section, is directly proportional to (A) Shear force (B) Area of the section (C) Distance of the C.G. of the area from its neutral axis (D) Moment of the beam section about its neutral axis

Description : Pick up the incorrect statement from the following. The intensity of horizontal shear stress at the elemental part of a beam section, is directly proportional to (A) Shear force (B) Area of the section ... . of the area from its neutral axis (D) Moment of the beam section about its neutral axis

Last Answer : Answer: Option D

For a reinforced concrete beam section, the shape of shear stress diagram is (a) Parabolic over the whole section with maximum value at the neutral axis. (b) Parabolic above the neutral axis and rectangular below the neutral axis. (c) Linearly varying as the distance form the N.A. (d) All the above.

Description : For a reinforced concrete beam section, the shape of shear stress diagram is (a) Parabolic over the whole section with maximum value at the neutral axis. (b) Parabolic above the neutral axis and rectangular below the neutral axis. (c) Linearly varying as the distance form the N.A. (d) All the above.

Last Answer : (b) Parabolic above the neutral axis and rectangular below the neutral axis.

In case of a beam subjected to pure bending a.107 dynes b.the stress intensity in any fibre is proportional to the distance of the fibre from the neutral axis c.the stress intensity in any fibre is proportional to the distance of the fibre from the load carrying end d.the stress intensity in any fibre is uniform e.the nature of stress in any fibre is identical

Description : In case of a beam subjected to pure bending a.107 dynes b.the stress intensity in any fibre is proportional to the distance of the fibre from the neutral axis c.the stress intensity in any fibre is ... d.the stress intensity in any fibre is uniform e.the nature of stress in any fibre is identical

Last Answer : b. the stress intensity in any fibre is proportional to the distance of the fibre from the neutral axis

State the position of maximum shear stress and bending stress in S/S rectangular beam section carrying udl.

Description : State the position of maximum shear stress and bending stress in S/S rectangular beam section carrying udl.

Last Answer : i. Maximum shear stress developed at the neutral axis of the rectangular section at support of simply supported beam. ii. Maximum bending stress developed at the top and bottom fibre of the rectangular section at mid span of simply supported beam.

The ratio of the length and diameter of a simply supported uniform circular beam which experiences maximum bending stress equal to tensile stress due to same load at its mid span, is (A) 1/8 (B) 1/4 (C) 1/2 (D) 1/3

Description : The ratio of the length and diameter of a simply supported uniform circular beam which  experiences maximum bending stress equal to tensile stress due to same load at its mid span, is  (A) 1/8  (B) 1/4  (C) 1/2  (D) 1/3 

Last Answer : (C) 1/2 

If Ac , Asc and A are areas of concrete, longitudinal steel and section of a R.C.C. column and m and c are the modular ratio and maximum stress in the configuration of concrete, the strength of column is (A) cAc + m cAsc (B) c (A - Asc) + m cAsc (C) c [A + (m - 1)ASC] (D) All the above

Description : If Ac , Asc and A are areas of concrete, longitudinal steel and section of a R.C.C. column and m and c are the modular ratio and maximum stress in the configuration of concrete, the strength of column is (A) cAc + m cAsc (B) c (A - Asc) + m cAsc (C) c [A + (m - 1)ASC] (D) All the above

Last Answer : Answer: Option D

is the pre-stressed force applied to the tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The maximum stress in the beam, subjected to a maximum bending moment , is (A) f = (P/A) + (Z/M) (B) f = (A/P) + (M/Z) (C) f = (P/A) + (M/Z) (D) f = (P/A) + (M/6Z)

Description : is the pre-stressed force applied to the tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The maximum stress in the beam, subjected to a maximum bending moment , is (A) f = (P/A) + (Z/M) ... ) + (M/Z) (C) f = (P/A) + (M/Z) (D) f = (P/A) + (M/6Z)

Last Answer : Answer: Option C

is the pre-stressed force applied to tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The minimum stress on the beam subjected to a maximum bending moment is (A) f = (P/A) - (Z/M) (B) f = (A/P) - (M/Z) (C) f = (P/A) - (M/Z) (D) f = (P/A) - (M/6Z)

Description : is the pre-stressed force applied to tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The minimum stress on the beam subjected to a maximum bending moment is (A) f = (P/A) - (Z/M) (B) f = (A/P) - (M/Z) (C) f = (P/A) - (M/Z) (D) f = (P/A) - (M/6Z)

Last Answer : Answer: Option C

Bending moment at any section in a conjugate beam gives in the actual beam (A) Slope (B) Curvature (C) Deflection (D) Bending moment

Description : Bending moment at any section in a conjugate beam gives in the actual beam (A) Slope (B) Curvature (C) Deflection (D) Bending moment

Last Answer : (C) Deflection

If M, I, R, E, F, and Y are the bending moment, moment of inertia, radius of curvature, modulus of elasticity stress and the depth of the neutral axis at section, then (A) M/I = R/E = F/Y (B) I/M = R/E = F/Y (C) M/I = E/R = E/Y (D) M/I = E/R = Y/F

Description : If M, I, R, E, F, and Y are the bending moment, moment of inertia, radius of curvature, modulus of  elasticity stress and the depth of the neutral axis at section, then  (A) M/I = R/E = F/Y (B) I/M = R/E = F/Y (C) M/I = E/R = E/Y (D) M/I = E/R = Y/F

Last Answer : (C) M/I = E/R = E/Y

A beam of uniform rectangular section 200 mm wide and 300mm deep is simply supported at its ends.It carries a uniformly distributed load of 9KN/m run over the entire span of 5m.If E=1×104 N/mm2, what is the maximum deflection? a.14.26 mm b.17.28 mm c.18.53 mm d.16.27 mm.

Description : A beam of uniform rectangular section 200 mm wide and 300mm deep is simply supported at its ends.It carries a uniformly distributed load of 9KN/m run over the entire span of 5m.If E=1×104 N/mm2, what is the maximum deflection? a.14.26 mm b.17.28 mm c.18.53 mm d.16.27 mm.

Last Answer : d.16.27 mm.

The strength of a beam depends upon (a) Its section modulus (b) Permissible bending stress (c) Both (a) and (b) (d) None of these

Description : The strength of a beam depends upon (a) Its section modulus (b) Permissible bending stress (c) Both (a) and (b) (d) None of these

Last Answer : (a) Its section modulus

If is the sectional area of a pre-stressed rectangular beam provided with a tendon pre-stressed by a force through its centroidal longitudinal axis, the compressive stress in concrete, is (A) P/A (B) A/P (C) P/2A (D) 2A/P

Description : If is the sectional area of a pre-stressed rectangular beam provided with a tendon pre-stressed by a force through its centroidal longitudinal axis, the compressive stress in concrete, is (A) P/A (B) A/P (C) P/2A (D) 2A/P

Last Answer : Answer: Option A

When a rectangular beam is loaded transversely, the maximum compressive stress develops on (A) Bottom fibre (B) Top fibre (C) Neutral axis (D) Every cross-section

Description : When a rectangular beam is loaded transversely, the maximum compressive stress develops on (A) Bottom fibre (B) Top fibre (C) Neutral axis (D) Every cross-section

Last Answer : (B) Top fibre

An R.C.C. beam of 25 cm width and 50 cm effective depth has a clear span of 6 metres and carries a U.D.L. of 3000 kg/m inclusive of its self weight. If the lever arm constant for the section is 0.865, the maximum intensity of shear stress, is (A) 8.3 kg/cm2 (B) 7.6 kg/cm2 (C) 21.5 kg/cm2 (D) 11.4 kg/cm2

Description : An R.C.C. beam of 25 cm width and 50 cm effective depth has a clear span of 6 metres and carries a U.D.L. of 3000 kg/m inclusive of its self weight. If the lever arm constant for the section is 0.865, the maximum intensity ... , is (A) 8.3 kg/cm2 (B) 7.6 kg/cm2 (C) 21.5 kg/cm2 (D) 11.4 kg/cm2

Last Answer : Answer: Option A

If the tendon is placed at an eccentricity e below the centroidal axis of the longitudinal axis of a rectangular beam (sectional modulus Z and stressed load P in tendon) the stress at the extreme top edge (A) Is increased by PZ/e (B) Is increased by Pe/Z (C) Is decreased by Pe/Z (D) Remains unchanged

Description : If the tendon is placed at an eccentricity e below the centroidal axis of the longitudinal axis of a rectangular beam (sectional modulus Z and stressed load P in tendon) the stress at the extreme top edge (A) Is ... by PZ/e (B) Is increased by Pe/Z (C) Is decreased by Pe/Z (D) Remains unchanged

Last Answer : Answer: Option C

The direct shear test suffers from the following disadvantage: (A) Drain condition cannot be controlled (B) Pore water pressure cannot be measured (C) Shear stress on the failure plane is not uniform (D) The area under the shear and vertical loads does not remain constant throughout the test

Description : The direct shear test suffers from the following disadvantage: (A) Drain condition cannot be controlled (B) Pore water pressure cannot be measured (C) Shear stress on the failure plane is not uniform (D) The area under the shear and vertical loads does not remain constant throughout the test

Last Answer : Answer: Option C

An R.C.C. beam of 6 m span is 30 cm wide and has a lever arm of 55 cm. If it carries a U.D.L. of 12 t per m and allowable shear stress is 5 kg/cm2 , the beam (A) Is safe in shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined bars (D) Needs revision of section

Description : An R.C.C. beam of 6 m span is 30 cm wide and has a lever arm of 55 cm. If it carries a U.D.L. of 12 t per m and allowable shear stress is 5 kg/cm2 , the beam (A) Is safe in shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined bars (D) Needs revision of section

Last Answer : Answer: Option D

The reduced levels of points, 30 metres apart along the longitudinal section of a road portion between chainages 5 and 9 are shown in the given figure. If there is a uniform up-gradient of the road 120 in 1, the chainage of the point with no filling or cutting is (A) (6 + 15) chains (B) (6 + 12) chains (C) (6 + 18) chains (D) None of these

Description : The reduced levels of points, 30 metres apart along the longitudinal section of a road portion between chainages 5 and 9 are shown in the given figure. If there is a uniform up-gradient of the road 120 in 1, the chainage ... 15) chains (B) (6 + 12) chains (C) (6 + 18) chains (D) None of these

Last Answer : (B) (6 + 12) chains

Which one of the following is the correct ratio of plastic moment to yield moment for a simply supported beam of uniform square cross section throughout the span (a) 1.5 (b) 1.7 (c) 2.0 (d) 2.34

Description : Which one of the following is the correct ratio of plastic moment to yield moment for a simply supported beam of uniform square cross section throughout the span (a) 1.5 (b) 1.7 (c) 2.0 (d) 2.34

Last Answer : (a) 1.5

A diagram which shows the variations of the axial load for all sections of the span of a beam, is called (A) Bending moment diagram (B) Shear force diagram (C) Thrust diagram (D) Stress diagram

Description : A diagram which shows the variations of the axial load for all sections of the span of a beam, is called (A) Bending moment diagram (B) Shear force diagram (C) Thrust diagram (D) Stress diagram

Last Answer : Answer: Option C

In a beam the local bond stress Sb, is equal to (A) Shear force/(Leaver arm × Total perimeter of reinforcement) (B) Total perimeter of reinforcement/(Leaver arm × Shear force) (C) Leaver arm/(Shear force × Total perimeter of reinforcement) (D) Leaver arm/(Bending moment × Total perimeter of reinforcement)

Description : In a beam the local bond stress Sb, is equal to (A) Shear force/(Leaver arm Total perimeter of reinforcement) (B) Total perimeter of reinforcement/(Leaver arm Shear force) (C) ... force Total perimeter of reinforcement) (D) Leaver arm/(Bending moment Total perimeter of reinforcement)

Last Answer : Answer: Option A

Pick up the incorrect statement from the following: Tensile reinforcement bars of a rectangular beam (A) Are curtailed if not required to resist the bending moment (B) Are bent up at suitable places to serve as shear reinforcement (C) Are bent down at suitable places to serve as shear reinforcement (D) Are maintained at bottom to provide at least local bond stress

Description : Pick up the incorrect statement from the following: Tensile reinforcement bars of a rectangular beam (A) Are curtailed if not required to resist the bending moment (B) Are bent up at suitable ... to serve as shear reinforcement (D) Are maintained at bottom to provide at least local bond stress

Last Answer : Answer: Option C

The stress in the wall of a cylinder in a direction normal to its longitudinal axis, due to a force acting along the circumference, is known as (A) Yield stress(B) Longitudinal stress (C) Hoop stress (D) Circumferential stress

Description : The stress in the wall of a cylinder in a direction normal to its longitudinal axis, due to a force  acting along the circumference, is known as  (A) Yield stress  (B) Longitudinal stress  (C) Hoop stress  (D) Circumferential stress 

Last Answer : (C) Hoop stress

The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of 4 tonnes at the centre. The maximum stress in the bottom most fibre at the mid span section, is (A) 13.33 kg/cm2 tensile (B) 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive

Description : The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of ... 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive

Last Answer : (C) 26.67 kg/cm2 tensile

What is the shear stress acting along the neutral axis, over a triangular section? a. 2.66 (S/bh) b. 1.5 (S/bh) c. 0.375 (S/bh) d. None of the above

Description : What is the shear stress acting along the neutral axis, over a triangular section? a. 2.66 (S/bh) b. 1.5 (S/bh) c. 0.375 (S/bh) d. None of the above

Last Answer : a. 2.66 (S/bh)

The intensity of direct longitudinal stress in the cross-section at any point distant r from the neutral axis, is proportional to (A) r (B) 1/r (C) r2 (D) 1/r²

Description : The intensity of direct longitudinal stress in the cross-section at any point distant r from the neutral axis, is proportional to (A) r (B) 1/r (C) r2 (D) 1/r²

Last Answer : (A) r

The following assumption is not true in the theory of pure torsion: (A) The twist along the shaft is uniform (B) The shaft is of uniform circular section throughout (C) Cross-section of the shaft, which is plane before twist remains plane after twist (D) All radii get twisted due to torsion

Description : The following assumption is not true in the theory of pure torsion:  (A) The twist along the shaft is uniform  (B) The shaft is of uniform circular section throughout  (C) Cross- ... , which is plane before twist remains plane after twist  (D) All radii get twisted due to torsion 

Last Answer : (D) All radii get twisted due to torsion 

Most important features of any spring are (a) Deflection, stiffness and strength (b) Stiffness, bending and shear strengths (c) Strain energy, deflection and strength (d) None

Description : Most important features of any spring are (a) Deflection, stiffness and strength (b) Stiffness, bending and shear strengths (c) Strain energy, deflection and strength (d) None

Last Answer : (c) Strain energy, deflection and strength

Most important features of any spring are (a) Deflection, stiffness and strength (b) Stiffness, bending and shear strengths (c) Strain energy, deflection and strength (d) None

Description : Most important features of any spring are (a) Deflection, stiffness and strength (b) Stiffness, bending and shear strengths (c) Strain energy, deflection and strength (d) None

Last Answer : (c) Strain energy, deflection and strength

The ratio of maximum bending stress to maximum shear stress on the cross section when a shaft is simultaneously subjected to a torque T and bending moment M, a. T/M b. M/T c. 2T/M d. 2M/T

Description : The ratio of maximum bending stress to maximum shear stress on the cross section when a shaft is simultaneously subjected to a torque T and bending moment M, a. T/M b. M/T c. 2T/M d. 2M/T

Last Answer : d. 2M/T

Select the incorrect statement from the following In eccentrically loaded columns, [ A ] The tensile strength of concrete is ignored [ B ] Design stress – strain curve for steel in compression is the same as in tension [ C ] The strain at different points in the section will be same [ D ] Plane section remain plane even after bending

Description : Select the incorrect statement from the following In eccentrically loaded columns, [ A ] The tensile strength of concrete is ignored [ B ] Design stress - strain curve for steel in compression is the ... different points in the section will be same [ D ] Plane section remain plane even after bending

Last Answer : [ C ] The strain at different points in the section will be same

The shear force on a simply supported beam is proportional to (A) Displacement of the neutral axis (B) Sum of the forces (C) Sum of the transverse forces (D) Algebraic sum of the transverse forces of the section

Description : The shear force on a simply supported beam is proportional to (A) Displacement of the neutral axis (B) Sum of the forces (C) Sum of the transverse forces (D) Algebraic sum of the transverse forces of the section

Last Answer : (D) Algebraic sum of the transverse forces of the section

A uniformly distributed load of 20 kN/m acts on a simply supported beam of rectangular cross section of width 20 mm and depth 60 mm. What is the maximum bending stress acting on the beam of 5m? a. 5030 Mpa b. 5208 Mpa c. 6600 Mpa d. Insufficient data

Description : A uniformly distributed load of 20 kN/m acts on a simply supported beam of rectangular cross section of width 20 mm and depth 60 mm. What is the maximum bending stress acting on the beam of 5m? a. 5030 Mpa b. 5208 Mpa c. 6600 Mpa d. Insufficient data

Last Answer : b. 5208 Mpa

A T-section beam having flange 180mm wide and 20 mm thick and web 150 mm long and 20 mm thick carries a udl of 80 kN/m over an effective span of 8 m. Calculate the maximum bending stress.

Description : A T-section beam having flange 180mm wide and 20 mm thick and web 150 mm long and 20 mm thick carries a udl of 80 kN/m over an effective span of 8 m. Calculate the maximum bending stress.

Last Answer : Solution :

In a reinforced concrete beam , the shear stress distribution above the neutral axis following a (a) A straight line (b) Circular curve (c) Parabolic curve (d) All the above

Description : In a reinforced concrete beam , the shear stress distribution above the neutral axis following a (a) A straight line (b) Circular curve (c) Parabolic curve (d) All the above

Last Answer : (c) Parabolic curve

A cast iron T section beam is subjected to pure bending. For maximum compressive stress to be three times the maximum tensile stress, centre of gravity of the section from flange side is (A) h/4 (B) h/3 (C) h/2 (D) 2/3 h

Description : A cast iron T section beam is subjected to pure bending. For maximum compressive stress to be  three times the maximum tensile stress, centre of gravity of the section from flange side is  (A) h/4  (B) h/3  (C) h/2  (D) 2/3 h

Last Answer : (A) h/4 

If a three hinged parabolic arch carries a uniformly distributed load on its entire span, every section of the arch resists. (A) Compressive force (B) Tensile force (C) Shear force (D) Bending moment

Description : If a three hinged parabolic arch carries a uniformly distributed load on its entire span, every section of the arch resists. (A) Compressive force (B) Tensile force (C) Shear force (D) Bending moment

Last Answer : (A) Compressive force

Pick up the correct statement from the following: (A) The moment of inertia is calculated about the axis about which bending takes place (B) If tensile stress is less than axial stress, the section experiences compressive stress (C) If tensile stress is equal to axial stress, the section experiences compressive stress (D) All the above

Description : Pick up the correct statement from the following:  (A) The moment of inertia is calculated about the axis about which bending takes place  (B) If tensile stress is less than axial ... tensile stress is equal to axial stress, the section experiences compressive stress  (D) All the above 

Last Answer : (D) All the above 

For shear strength, triaxial shear test is suitable because (A) It can be performed under all three drainage conditions (B) Precise measurement of the pore pressure and volume change during the test is possible (C) Stress distribution on the failure plane, is uniform (D) All the above

Description : For shear strength, triaxial shear test is suitable because (A) It can be performed under all three drainage conditions (B) Precise measurement of the pore pressure and volume change during the test is possible (C) Stress distribution on the failure plane, is uniform (D) All the above

Last Answer : (D) All the above